AFAIK there aren't any cases where we will/should hit the old code
path for our supported qemu versions, so drop the old code.
Massive test suite churn follows
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
If you've ever tried running a huge page backed guest under
different user than in qemu.conf, you probably failed. Problem is
even though we have corresponding APIs in the security drivers,
there's no implementation and thus we don't relabel the huge page
path. But even if we did, so far all of the domains share the
same path:
/hugepageMount/libvirt/qemu
Our only option there would be to set 0777 mode on the qemu dir
which is totally unsafe. Therefore, we can create dir on
per-domain basis, i.e.:
/hugepageMount/libvirt/qemu/domainName
and chown domainName dir to the user that domain is configured to
run under.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.1 the -drive argument can be used to configure
all disks, so the QEMU driver can assume it is always available
and drop support for -hda/-cdrom/etc.
Many of the tests need updating because a great many were
running without CAPS_DRIVE set, so using the -hda legacy
syntax.
Fixing the tests uncovered a bug in the argv -> xml
convertor which failed to handle disk with if=floppy.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
This patch teaches testutil how to read multi-line input files with
backspace-newline line continuation markers.
The patch also breaks up all the single-line arguments test input files into
multi-line files with lines shorter than 80 characters.
Add option to domain XML for
<memoryBacking>
<hugepages/>
</memoryBacking>
* configure.in: Add check for mntent.h
* qemud/libvirtd_qemu.aug, qemud/test_libvirtd_qemu.aug, src/qemu.conf
Add 'hugetlbfs_mount' config parameter
* src/qemu_conf.c, src/qemu_conf.h: Check for -mem-path flag in QEMU,
and pass it when hugepages are requested.
Load hugetlbfs_mount config parameter, search for mount if not given.
* src/qemu_driver.c: Free hugetlbfs_mount/path parameter in driver shutdown.
Create directory for QEMU hugepage usage, chowning if required.
* docs/formatdomain.html.in: Document memoryBacking/hugepages elements
* docs/schemas/domain.rng: Add memoryBacking/hugepages elements to schema
* src/util.c, src/util.h, src/libvirt_private.syms: Add virFileFindMountPoint
helper API
* tests/qemuhelptest.c: Add -mem-path constants
* tests/qemuxml2argvtest.c, tests/qemuxml2xmltest.c: Add tests for hugepage
handling
* tests/qemuxml2argvdata/qemuxml2argv-hugepages.xml,
tests/qemuxml2argvdata/qemuxml2argv-hugepages.args: Data files for
hugepage tests
