Currently, boot order can be specified per device class but there is no
way to specify exact disk/NIC device to boot from.
This patch adds <boot order='N'/> element which can be used inside
<disk/> and <interface/>. This is incompatible with the older os/boot
element. Since not all hypervisors support per-device boot
specification, new deviceboot flag is included in capabilities XML for
hypervisors which understand the new boot element. Presence of the flag
allows (but doesn't require) users to use the new style boot order
specification.
This is in response to a request in:
https://bugzilla.redhat.com/show_bug.cgi?id=665293
In short, under heavy load, it's possible for qemu's networking to
lock up due to the tap device's default 1MB sndbuf being
inadequate. adding "sndbuf=0" to the qemu commandline -netdevice
option will alleviate this problem (sndbuf=0 actually sets it to
0xffffffff).
Because we must be able to explicitly specify "0" as a value, the
standard practice of "0 means not specified" won't work here. Instead,
virDomainNetDef also has a sndbuf_specified, which defaults to 0, but
is set to 1 if some value was given.
The sndbuf value is put inside a <tune> element of each <interface> in
the domain. The intent is that further tunable settings will also be
placed inside this element.
<interface type='network'>
...
<tune>
<sndbuf>0</sndbuf>
...
</tune>
</interface>
This patch is in response to
https://bugzilla.redhat.com/show_bug.cgi?id=643050
The existing libvirt support for the vhost-net backend to the virtio
network driver happens automatically - if the vhost-net device is
available, it is always enabled, otherwise the standard userland
virtio backend is used.
This patch makes it possible to force whether or not vhost-net is used
with a bit of XML. Adding a <driver> element to the interface XML, eg:
<interface type="network">
<model type="virtio"/>
<driver name="vhost"/>
will force use of vhost-net (if it's not available, the domain will
fail to start). if driver name="qemu", vhost-net will not be used even
if it is available.
If there is no <driver name='xxx'/> in the config, libvirt will revert
to the pre-existing automatic behavior - use vhost-net if it's
available, and userland backend if vhost-net isn't available.
* docs/hacking.html.in (Curly braces): Tighten recommendations to
disallow if (cond) one-line; else { block; }.
* HACKING: Regenerate.
Suggested by Daniel P. Berrange.
At this point everything is already in place to make IPv6 happen, we just
need to add a few rules, remove some checks for IPv4-only, and document
the changes to the XML on the website.
This commit adds support for IPv6 parsing and formatting to the
virtual network XML parser, including moving around data definitions
to allow for multiple <ip> elements on a single network, but only
changes the consumers of this API to accommodate for the changes in
API/structure, not to add any actual IPv6 functionality. That will
come in a later patch - this patch attempts to maintain the same final
functionality in both drivers that use the network XML parser - vbox
and "bridge" (the Linux bridge-based driver used by the qemu
hypervisor driver).
* src/libvirt_private.syms: Add new private API functions.
* src/conf/network_conf.[ch]: Change C data structure and
parsing/formatting.
* src/network/bridge_driver.c: Update to use new parser/formatter.
* src/vbox/vbox_tmpl.c: update to use new parser/formatter
* docs/schemas/network.rng: changes to the schema -
* there can now be more than one <ip> element.
* ip address is now an ip-addr (ipv4 or ipv6) rather than ipv4-addr
* new optional "prefix" attribute that can be used in place of "netmask"
* new optional "family" attribute - "ipv4" or "ipv6"
(will default to ipv4)
* define data types for the above
* tests/networkxml2xml(in|out)/nat-network.xml: add multiple <ip> elements
(including IPv6) to a single network definition to verify they are being
correctly parsed and formatted.
In practice this has always been optional, but the RNG has shown it as
mandatory, and since all the examples for make check had it, it was
never noticed. One of the existing test cases has been changed to
check for this.
I also noticed that the dhcp/host/ip was still defined as <text/>,
but should really be <ref name='ipv4-addr'/>
formatnetwork.html has a menu item at level 3. libvirt.css
doesn't have a explicit rule for level 3 and level 3 and
level 2 items end up at the same indentation level.
Add an additional 1em indentation to level 3 menu items.
The xml watchdog dump option is converted to qemu watchdog pause arg
but it is not reasonable to convert it back from qemu watchdog pause
arg since there already is a xml watchdog pause option, so a test for
the dump option to convert it from arg to xml is not added.
Changes common to all network disks:
-Make source name optional in the domain schema, since NBD doesn't use it
-Add a hostName type to the domain schema, and use it instead of genericName, which doesn't include .
-Don't leak host names or ports
-Set the source protocol in qemuParseCommandline
Signed-off-by: Josh Durgin <joshd@hq.newdream.net>
This patch adds network disk support to libvirt/QEMU. The currently
supported protocols are nbd, rbd, and sheepdog. The XML syntax is like
this:
<disk type="network" device="disk">
<driver name="qemu" type="raw" />
<source protocol='rbd|sheepdog|nbd' name="...some image identifier...">
<host name="mon1.example.org" port="6000">
<host name="mon2.example.org" port="6000">
<host name="mon3.example.org" port="6000">
</source>
<target dev="vda" bus="virtio" />
</disk>
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Guarantee that outbuf/errbuf are allocated on success, even if to the
empty string. Caller always has to free the result, and empty output
check requires checking if *outbuf=='\0'. Makes the API easier to use
safely. Failure is best effort allocation (some paths, like
out-of-memory, cannot allocate a buffer, but most do), so caller must
free buffer on failure.
* docs/internals/command.html.in: Update documentation.
* src/util/command.c (virCommandSetOutputBuffer)
(virCommandSetErrorBuffer, virCommandProcessIO) Guarantee empty
string on no output.
* tests/commandtest.c (test17): New test.
* docs/internals/command.html.in: Better documentation of buffer
vs. fd considerations.
* src/util/command.c (virCommandRunAsync): Reject raw execution
with string io.
(virCommandRun): Reject execution with user-specified fds not
visiting a regular file.
The XML docs describe a 'port' attribute for the
storage source <host> element, but the parser never
handled it.
* docs/schemas/storagepool.rng: Define port attribute
* src/conf/storage_conf.c: Add missing parsing/formatting
of host port number
* src/conf/storage_conf.h: Remove bogus/unused 'protocol' field
Similarly to deprecating close(), I am now deprecating fclose() and
introduce VIR_FORCE_FCLOSE() and VIR_FCLOSE(). Also, fdopen() is replaced with
VIR_FDOPEN().
Most of the files are opened in read-only mode, so usage of
VIR_FORCE_CLOSE() seemed appropriate. Others that are opened in write
mode already had the fclose()< 0 check and I converted those to
VIR_FCLOSE()< 0.
I did not find occurrences of possible double-closed files on the way.
IP addresses and MAC addresses had been defined in the RNG simply as
<text/> meaning that, according to the RNG, any string could go in
there. Of course the C parsing code does a much better job of
validating, but we may as well have this describing the contents
accurately (even though it's currently only used during "make check").
All the other RNG files in libvirt are enclosed within <grammar>. This
commit makes the syntactical changes necessary to make network.rng fit
that pattern. (This is the first step in adding some data type
definitions to network.rng for more exact validation of IP and MAC
addresses).
Formatting changes (indentation) will be done in a subsequent commit,
so that actual changes to the code won't be obscured by whitespace.
* docs/schemas/domain.rng: Fix merge error which left SPICE channel
elements under VNC schema.
* tests/qemuhelptest.c: Add SPICE flag to kvm-83 test
* tests/qemuxml2argvdata/qemuxml2argv-graphics-spice.xml: Add
<memballoon> element
This extends the SPICE XML to allow channel security options
<graphics type='spice' port='-1' tlsPort='-1' autoport='yes'>
<channel name='main' mode='secure'/>
<channel name='record' mode='insecure'/>
</graphics>
Any non-specified channel uses the default, which allows both
secure & insecure usage
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/libvirt_private.syms: Add XML syntax for specifying per
channel security options for spice.
* src/qemu/qemu_conf.c: Configure channel security with spice
This extends the XML syntax for <graphics> to allow a password
expiry time to be set
eg
<graphics type='vnc' port='5900' autoport='yes' keymap='en-us' passwd='12345' passwdValidTo='2010-04-09T15:51:00'/>
The timestamp is in UTC.
* src/conf/domain_conf.h: Pull passwd out into separate struct
virDomainGraphicsAuthDef to allow sharing between VNC & SPICE
* src/conf/domain_conf.c: Add parsing/formatting of new passwdValidTo
argument
* src/opennebula/one_conf.c, src/qemu/qemu_conf.c, src/qemu/qemu_driver.c,
src/xen/xend_internal.c, src/xen/xm_internal.c: Update for changed
struct containing VNC password
This adds an element
<graphics type='spice' port='5903' tlsPort='5904' autoport='yes' listen='127.0.0.1'/>
This is the bare minimum that should be exposed in the guest
config for SPICE. Other parameters are better handled as per
host level configuration tunables
* docs/schemas/domain.rng: Define the SPICE <graphics> schema
* src/domain_conf.h, src/domain_conf.c: Add parsing and formatting
for SPICE graphics config
* src/qemu_conf.c: Complain about unsupported graphics types
* src/qemu_conf.c: Add dummy entry in enumeration
* docs/schemas/domain.rng: Add 'qxl' as a type for the <video> tag
* src/domain_conf.c, src/domain_conf.h: Add QXL to video type
enumerations
the element has a mode attribute allowing only 3 values:
- emulate: use the smbios emulation from the hypervisor
- host: try to use the smbios values from the node
- sysinfo: grab the values from the <sysinfo> fields
* docs/schemas/domain.rng: extend the schemas
* src/conf/domain_conf.h: add the flag to the domain config
* src/conf/domain_conf.h: parse and serialize the smbios if present
Reordered the bindings into alphabetical order, added a link to
the php-libvirt source on Github, plus gave the direct package
names needed for Python usage on RHEL/Fedora, and Ubuntu.
The default location for the XML catalog file, /etc/xml/catalog,
used when validating the generated html docs, isn't correct for
MacOS X.
This commit adds an option to the configure script, allowing the
default to be overridden:
--with-xml-catalog-file=/path/to/xml/catalog/file
Previously, only the API docs were installed, rather than the
complete documentation set. This commit ensures the complete
documentation set is installed.
Syntax agreed on in
https://www.redhat.com/archives/libvir-list/2010-September/msg00476.html
<domain ...>
<vcpu current='x'>y</vcpu>
...
can now be used to specify 1 <= x <= y current vcpus, in relation
to the boot-time max of y vcpus. If current is omitted, then
current and max are assumed to be the same value.
* docs/schemas/domain.rng: Add new attribute.
* docs/formatdomain.html.in: Document it.
* tests/qemuxml2argvdata/qemuxml2argv-smp.xml: Add to
domainschematest.
* tests/xml2sexprdata/xml2sexpr-pv-vcpus.xml: Likewise.
Since bugs due to double-closed file descriptors are difficult to track down in a multi-threaded system, I am introducing the VIR_CLOSE(fd) macro to help avoid mistakes here.
There are lots of places where close() is being used. In this patch I am only cleaning up usage of close() in src/conf where the problems were.
I also dare to declare close() as being deprecated in libvirt code base (HACKING).
* docs/formatdomain.html.in: Add memtune element details, added min_guarantee
* src/libvirt.c: Update virDomainGetMemoryParameters api description, make
it more clear that the user first needs to call the api to get the number
of parameters supported and then call again to get the values.
* tools/virsh.pod: Add usage of new command memtune in virsh manpage
https://bugzilla.redhat.com/show_bug.cgi?id=623903 documents a qemu
bug that causes libvirt to hang if virt-manager happens to be
querying balloon info when a guest is paused. Until the qemu bug
is fixed, people need to know how to avoid the issue.
* docs/formatdomain.html.in (Memory balloon device): Mention
model='none'.
This introduces new attribute to filesystem element
to support customizable access mode for mount type.
Valid accessmode are: passthrough, mapped and squash.
Usage:
<filesystem type='mount' accessmode='passthrough'>
<source dir='/export/to/guest'/>
<target dir='mount_tag'/>
</filesystem>
passthrough is the default model if not specified, that's
also the current behaviour.
* include/libvirt/libvirt.h.in: some of the function type description
were broken so they could not be automatically documented
* src/util/event.c docs/apibuild.py: event.c exports one public API
so it needs to be scanned too, avoid a few warnings
To enable the CPU XML from the capabilities to be pasted directly
into the guest XML with no editing, pick a sensible default for
match and feature policy. The CPU match will be exact and the
feature policy will be require. This should ensure safety for
migration and give DWIM semantics for users
* src/conf/cpu_conf.c: Default to exact match and require policy
* docs/formatdomain.html.in: Document new defaults
This adds a script to generate the todo item page from
bugzilla. This requires a valid username+password for
bugzilla, so it is intended that this only be run on
the libvirt.org website via cron. Normal usage will just
generate an empty stub page.
* docs/todo.pl: Script to extract todo items from bugzilla
* docs/todo.cfg-example: Example config file
* docs/sitemap.html.in: Add todo page
* docs/Makefile.am: Generation rules for todo items
This patch adds another example to the nwfilter html page and provides 2 solutions for how to write a filter meeting the given requirements using newly added features.
Since version 4.1 ESX(i) can expose virtual serial devices over TCP.
Add support in the VMX handling code for this, add test cases to cover
it and add links to some documentation.
ESX supports two additional protocols: TELNETS and TLS. Add them to
the list of serial-over-TCP protocols.
The <vcpu cpuset=...> attribute has been available since commit
e193b5dd, but without documentation or RNG validation.
* docs/schemas/domain.rng (vcpu): Further validate cpuset.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.c: Fix typos.
Prior to this patch, the ChangeLog generation was hard coded to use
"awk", when it should have been using the AWK variable set by our
build system.
This breaks compilation on a newly installed OS X system, where the
default path has the Mac (non GNU) awk in the default search PATH
before any installed GNU awk (gawk).
Tweaked the PolicyKit documentation improvement patch submitted
by Patrick Dignan.
Additionally, removed the reference to PolicyKit.conf, which is
no longer used by PolicyKit, plus added a link to the expanded
PolicyKit example page on the wiki.
Added a workable initial page for the libvirt Application
Development Guide, giving the online viewable options +
the available download ones (pdf, epub, srpm).
Added a link to the PDF to the main Downloads page, plus
neatened the html tags throughout the page as they
were a bit of a mess.
Added --enable-compile-warnings=error to the autogen line,
as suggested by Eric Blake.
Xen supports on_crash actions coredump-{destroy,restart}. libvirt
cannot parse config returned by xend that contains either of these
actions
xen52 # xm li -l test | grep on_crash
(on_crash coredump-restart)
xen52 # virsh dumpxml test
error: internal error unknown lifecycle type coredump-restart
This patch adds a new virDomainLifecycleCrash enum and appends
the new options to existing destroy, restart, preserve, and
rename-restart options.
I wrote a patch to add support for listing the Vendor and Model of a
storage pool in the storage pool XML. This would allow vendor
extensions of specific devices. The patch includes a test for the new
attributes as well.
Patrick Dignan
Add documentation for features added a while ago.
* docs/formatdomain.html.in (Time keeping): Update documentation
of <clock> element to match 0.8.0 addition.
The balloon device is automatically added to qemu guests if supported,
but it may be useful to desactivate it. The simplest to not change the
existing behaviour is to allow
<memballoon type="none"/>
as an extra option to desactivate it (it is automatically added if the
memballoon construct is missing for the domain).
The following simple patch just adds the extra option and does not
change the default behaviour but avoid creating a balloon device if
type="none" is used.
* docs/schemas/domain.rng: add the extra type attribute value
* src/conf/domain_conf.c src/conf/domain_conf.h: add the extra enum
value
* src/qemu/qemu_conf.c: if enum is NONE, don't activate the device,
i.e. don't pass the args to qemu/kvm
Now a vpx:// connection has an explicitly specified host. This
allows to enabled several functions for a vpx:// connection
again, like host UUID, hostname, general node info, max vCPU
count, free memory, migration and defining new domains.
Lookup datacenter, compute resource, resource pool and host
system once and cache them. This simplifies the rest of the
code and reduces overall HTTP(S) traffic a bit.
esx:// and vpx:// can be mixed freely for a migration.
Ensure that migration source and destination refer to the
same vCenter. Also directly encode the resource pool and
host system object IDs into the migration URI in the prepare
function. Then directly build managed object references in
the perform function instead of re-looking up already known
information.
All <console> devices now export a <target> type attribute. QEMU defaults
to 'serial', UML defaults to 'uml, xen can be either 'serial' or 'xen'
depending on fullvirt. Understandably there is lots of test fallout.
This will be used to differentiate between a serial vs. virtio console for
QEMU.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Add a new element to the <os> block:
<bootmenu enable="yes|no"/>
Which maps to -boot,menu=on|off on the QEMU command line.
I decided to use an explicit 'enable' attribute rather than just make the
bootmenu element boolean. This allows us to treat lack of a bootmenu element
as 'use hypervisor default'.
Add a pointer to the primary context of a connection and use it in all
driver functions that don't dependent on the context type. This includes
almost all functions that deal with a virDomianPtr. Therefore, using
a vpx:// connection allows you to perform all the usual domain related
actions like start, destroy, suspend, resume, dumpxml etc.
Some functions that require an explicitly specified ESX server don't work
yet. This includes the host UUID, the hostname, the general node info, the
max vCPU count and the free memory. Also not working yet are migration and
defining new domains.
Thanks to DV for knocking together the Relax-NG changes
quickly for me.
Changes since v1:
- Change the domain.rng to correspond to the new schema
- Don't allocate caps->ns in testQemuCapsInit since it is a static table
Changes since v2:
- Change domain.rng to add restrictions on allowed environment names
Changes since v3:
- Remove a bogus comment in the tests
Signed-off-by: Chris Lalancette <clalance@redhat.com>
To allow compatibility with older QEMU PCI device slot assignment
it is necessary to explicitly track the balloon device in the
XML. This introduces a new device
<memballoon model='virtio|xen'/>
It can also have a PCI address, auto-assigned if necessary.
The memballoon will be automatically added to all Xen and QEMU
guests by default.
* docs/schemas/domain.rng: Add <memballoon> element
* src/conf/domain_conf.c, src/conf/domain_conf.h: parsing
and formatting for memballoon device. Always add a memory
balloon device to Xen/QEMU if none exists in XML
* src/libvirt_private.syms: Export memballoon model APIs
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Honour the
PCI device address in memory balloon device
* tests/*: Update to test new functionality
By specifying <vendor> element in CPU requirements a guest can be
restricted to run only on CPUs by a given vendor. Host CPU vendor is
also specified in capabilities XML.
The vendor is checked when migrating a guest but it's not forced, i.e.,
guests configured without <vendor> element can be freely migrated.
(EXTRA_DIST): Remove redundant listing of xml files.
(html/%-%.html, html/%-virterror.html, %-api.xml, %-refs.xml):
Rewrite with...
(python_generated_files): ...new macro, since make didn't see
through the dependency chain correctly otherwise.
Also don't abuse the disk driver name to specify the SCSI controller
model anymore:
<driver name='buslogic'/>
Use the newly added model attribute of the controller element for this:
<controller type='scsi' index='0' model='buslogic'/>
The disk driver name approach is deprecated now, but still works for
backward compatibility reasons.
Update the documentation and tests accordingly.
Fix usage of the words controller and id in the VMX handling code. Use
controller, bus and unit properly.
According to docs/formatdomain.html.in, "The boot element can be
repeated multiple times to setup a priority list of boot devices to try
in turn." The Relax-NG schema required / allowed exactly one entry.
Signed-off-by: Philipp Hahn <hahn@univention.de>
This patch adds an optional XML attribute to a nwfilter rule to give the user control over whether the rule is supposed to be using the iptables state match or not. A rule may now look like shown in the XML below with the statematch attribute either having value '0' or 'false' (case-insensitive).
[...]
<rule action='accept' direction='in' statematch='false'>
<tcp srcmacaddr='1:2:3:4:5:6'
srcipaddr='10.1.2.3' srcipmask='32'
dscp='33'
srcportstart='20' srcportend='21'
dstportstart='100' dstportend='1111'/>
</rule>
[...]
I am also extending the nwfilter schema and add this attribute to a test case.
The virtio serial changes broke the test suite because they forgot
to add the new address attribute to the domain XML schema. The
xml2xml test also broke because the XML no longer roundtrips. This
is due to testing of auto-addition of <controller> elements. Split
that test case off into a separate XML file to avoid breakage
* docs/schemas/domain.rng: Allow port number for virtio serial addresses
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: Revert to
a simple config to avoid breaking xml2xml test
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.xml,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.args: Add
complex test case for auto-controller addition for xml2argv test
* tests/qemuxml2argvtest.c: Add channel-virtio-auto test
Otherwise, 'make check' in the python dir tries to reference a file in
docs that is built by 'make' but not by 'make check'.
* docs/Makefile.am (check-local): New rule.
Reported by Matthias Bolte.
A build on Ubuntu reported:
|| Generating formatnwfilter.html.tmp
/dados/develop/libvirt/docs/formatnwfilter.html.in|390| HTML parser error : Unexpected end tag : p
|| </p>
|| ^
/dados/develop/libvirt/docs/formatnwfilter.html.in|705| HTML parser error : Unexpected end tag : code
|| <td>End of range of valid source ports</code></td>
|| ^
/dados/develop/libvirt/docs/formatnwfilter.html.in|710| HTML parser error : Unexpected end tag : code
|| <td>Start of range of valid destination ports</code></td>
|| ^
* docs/formatnwfilter.html.in: Fix invalid HTML constructs.
Reported by Eduardo Otubo.
This patch parses the following two XML descriptions, one for
802.1Qbg and one for 802.1Qbh, and stores the data internally.
The actual triggering of the switch setup protocol has not been
implemented here but the relevant code to do that should go into
the functions associatePortProfileId() and disassociatePortProfileId().
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbg'>
<parameters managerid='12' typeid='0x123456' typeidversion='1'
instanceid='fa9b7fff-b0a0-4893-8e0e-beef4ff18f8f'/>
</virtualport>
<filterref filter='clean-traffic'/>
</interface>
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbh'>
<parameters profileid='my_profile'/>
</virtualport>
</interface>
I'd suggest to use this patch as a base for triggering the setup
protocol with the 802.1Qb{g|h} switch.
Several rounds of changes were made to this patch. The
following is a list of these changes.
- Renamed structure virVirtualPortProfileDef to virVirtualPortProfileParams
as per Daniel Berrange's request
- Addressing Daniel Berrange's comments:
- removing macvtap.h's dependency on domain_conf.h by
moving the virVirtualPortProfileDef structure into macvtap.h
and not passing virtDomainNetDefPtr to any functions in
macvtap.c
- Addressed most of Chris Wright's comments:
- indicating error in case virtualport XML node cannot be parsed
properly
- parsing hex and decimal numbers using virStrToLong_ui() with
parameter '0' for base
- tgifname (target interface name) variable wasn't necessary
to pass to openMacvtapTap function anymore
- assigning the virtual port data structure to the virDomainNetDef
only if it was previously parsed
- make sure that the error code returned by openMacvtapTap() is a negative n
in case the associatePortProfileId() function failed.
- renaming vsi in the XML to virtualport
- replace all occurrences of vsi in the source as well
- removing mode and MAC address parameters from the functions that
will communicate with the hareware diretctly or indirectly
- moving the associate and disassociate functions to the end of the
file for subsequent patches to easier make them generally available
for export
- passing the macvtap interface name rather than the link device since
this otherwise gives funny side effects when using netlink messages
where IFLA_IFNAME and IFLA_ADDRESS are specified and the link dev
all of a sudden gets the MAC address of the macvtap interface.
- Removing rc = -1 error indications in the case of 802.1Qbg|h setup in case
we wanted to use hook scripts for the setup and so the setup doesn't fail
here.
- if instance ID UUID is not supplied it will automatically be generated
- adapted schema to make instance ID UUID optional
- added test case
- parser and XML generator have been separated into their own
functions so they can be re-used elsewhere (passthrough case
for example)
- Adapted XML parser and generator support the above shown type
(802.1Qbg, 802.1Qbh).
- Adapted schema to above XML
- Adapted test XML to above XML
- Passing through the VM's UUID which seems to be necessary for
802.1Qbh -- sorry no host UUID
- adding virtual function ID to association function, in case it's
necessary to use (for SR-IOV)
Allow for a host UUID in the capabilities XML. Local drivers
will initialize this from the SMBIOS data. If a sanity check
shows SMBIOS uuid is invalid, allow an override from the
libvirtd.conf configuration file
* daemon/libvirtd.c, daemon/libvirtd.conf: Support a host_uuid
configuration option
* docs/schemas/capability.rng: Add optional host uuid field
* src/conf/capabilities.c, src/conf/capabilities.h: Include
host UUID in XML
* src/libvirt_private.syms: Export new uuid.h functions
* src/lxc/lxc_conf.c, src/qemu/qemu_driver.c,
src/uml/uml_conf.c: Set host UUID in capabilities
* src/util/uuid.c, src/util/uuid.h: Support for host UUIDs
* src/node_device/node_device_udev.c: Use the host UUID functions
* tests/confdata/libvirtd.conf, tests/confdata/libvirtd.out: Add
new host_uuid config option to test
* docs/hacking.html.in: Use the "curly braces" section from coreutils'
HACKING, adapting for libvirt's different formatting style.
* HACKING: Sync from the above, still mostly manually.
So far the references to other filters needed to appear before filtering
rules. With the below patch they can now appear in any order.
Also I forgot to add a couple of 'rarp's.
This patch adds support for the RARP protocol. This may be needed due to
qemu sending out a RARP packet (at least that's what it seems to want to
do even though the protocol id is wrong) when migration finishes and
we'd need a rule to let the packets pass.
Unfortunately my installation of ebtables does not understand -p RARP
and also seems to otherwise depend on strings in /etc/ethertype
translated to protocol identifiers. Therefore I need to pass -p 0x8035
for RARP. To generally get rid of the dependency of that file I switch
all so far supported protocols to use their protocol identifier in the
-p parameter rather than the string.
I am also extending the schema and added a test case.
changes from v1 to v2:
- added test case into patch
With this patch I want to enable hex number inputs in the filter XML. A
number that was entered as hex is also printed as hex unless a string
representing the meaning can be found.
I am also extending the schema and adding a test case. A problem with
the DSCP value is fixed on the way as well.
Changes from V1 to V2:
- using asHex boolean in all printf type of functions to select the
output format in hex or decimal format
* configure.ac docs/news.html.in libvirt.spec.in src/libvirt_public.syms:
updates for release of 0.8.0
* po/*.po po/libvirt.pot: updated a lar set of localizations, and merge
the messages
Extend tests to cover all SCSI controller types and document the
new type.
The lsisas1068 SCSI controller type was added in ESX 4.0. The VMX
parser reports an error when this controller type is present. This
makes virsh dumpxml fail for every domain that uses this controller
type.
This patch fixes this and adds lsisas1068 to the list of accepted
SCSI controller types.
Reported by Jonathan Kelley.
This patch adds a relaxng nwfilter schema along with a test that
verifies all the test output XML against the schema. The input XMLs
contain a lot of intentional out-of-range values that make them fail the
schema verification, so I am not verifying against those.
The clock timer XML is being updated in the following ways (based on
further off-list discussion that was missed during the initial
implementation):
1) 'wallclock' is changed to 'track', and the possible values are 'boot'
(corresponds to old 'host'), 'guest', and 'wall'.
2) 'mode' has an additional value 'smpsafe'
3) when tickpolicy='catchup', there can be an optional sub-element of
timer called 'catchup':
<catchup threshold=123 slew=120 limit=10000/>
Those three values are all longs, always optional, and if they are present,
they are positive. Internally, 0 indicates "unspecified".
* docs/schemas/domain.rng: updated RNG definition to account for changes
* src/conf/domain_conf.h: change the C struct and enums to match changes.
* src/conf/domain_conf.c: timer parse and format functions changed to
handle the new selections and new element.
* src/libvirt_private.syms: *TimerWallclock* changes to *TimerTrack*
* src/qemu/qemu_conf.c: again, account for Wallclock --> Track change.
* cfg.mk (sc_prohibit_test_minus_ao): Also check for [.
* docs/Makefile.am (%.html, html/index.html): Avoid non-portable
test usage.
* libvirt.spec.in (%post): Likewise.
* tools/virt-pki-validate.in (servercert.pem): Likewise.
* configure.ac (LOGNAME): Use test, not [, in files processed by
autoconf.
Detected by Matthias Bolte.
timers are sub-elements of clocks. A clock can have zero or more
instances of timer. Within the timer, only the name attribute is
required; all other attributes are optional.
A simpler representation of a timer element is:
<timer name='platform|pit|rtc|hpet|tsc'
wallclock='host|guest'
tickpolicy='delay|catchup|merge|discard'
frequency='123'
mode='auto|native|emulate|paravirt'
present='yes|no'/>
frequency is a ulong. All other attributes are simple enums.
* Fixes per feedback from Dan and Daniel
* Added test datafiles
* Re-disabled JSON flags
* Added code to print the error policy attribute when generating XML
* Re-add empty tag
In the documentation mention that the direct device support is there
since libvirt 0.7.7. A Linux kernel 2.6.34 is required for macvtap to be
available as standard device.
With N_() in place, we can use it for a smaller file.
* doc/api-extension/0008-Step-8-of-8-Add-virsh-support.patch:
Replace all uses of gettext_noop with N_.
* tools/virsh.c: Likewise, throughout the file.
* configure.ac libvirt.spec.in: update with new version
* docs/news.html.in: add list of changes in 0.7.7
* po/*po*: updated spanish and russian localisations, rebuilt
This extends the XML to allow for
<clock offset='timezone' timezone='Europe/Paris'/>
This is useful if the admin has not configured any timezone on the
host OS, but still wants to synchronize a guest to a specific one.
* src/conf/domain_conf.h, src/conf/domain_conf.c: Support extra
'timezone' attribute on clock configuration
* docs/schemas/domain.rng: Add 'timezone' attribute
* src/xen/xend_internal.c, src/xen/xm_internal.c: Reject configs
with a configurable timezone
This introduces a third option for clock offset synchronization,
that allows an arbitrary / variable adjustment to be set. In
essence the XML contains the time delta in seconds, relative to
UTC.
<clock offset='variable' adjustment='123465'/>
The difference from 'utc' mode, is that management apps should
track adjustments and preserve them at next reboot.
* docs/schemas/domain.rng: Schema for new clock mode
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parse
new clock time delta
* src/libvirt_private.syms, src/util/xml.c, src/util/xml.h: Add
virXPathLongLong() method
Add missing rule to build html/libvirt-libvirt.html.
Use a GNU Make pattern rule to avoid running apibuild.py once
for each out-of-date target, in a parallel build.
* docs/Makefile.am
* docs/Makefile.am (libvirt-api.xml libvirt-refs.xml): Generalize
apibuild.py to work in a non-srcdir build. Pass "srcdir" to it.
* docs/apibuild.py (rebuild): Honor the $srcdir envvar.
* docs/Makefile.am (MAINTAINERCLEANFILES): Use this variable
for generated-and-distributed files, not "CLEANFILES".
Besides, "make clean" and "make distclean" should not delete
distributed files.
Add support for virtio-serial by defining a new 'virtio' channel target type
and a virtio-serial controller. Allows the following to be specified in a
domain:
<controller type='virtio-serial' index='0' ports='16' vectors='4'/>
<channel type='pty'>
<target type='virtio' name='org.linux-kvm.port.0'/>
<address type='virtio-serial' controller='0' bus='0'/>
</channel>
* docs/schemas/domain.rng: Add virtio-serial controller and virtio
channel type.
* src/conf/domain_conf.[ch]: Domain parsing/serialization for
virtio-serial controller and virtio channel.
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: add domain xml
parsing test
* src/libvirt_private.syms src/qemu/qemu_conf.c:
virDomainDefAddDiskControllers() renamed to
virDomainDefAddImplicitControllers()
The current schema is more permissive than the XML parsing code in
libvirt. Precisely, 'match' attribute is optional in schema while in
reality its use is bound to <model> element:
- <cpu> element without 'match' attribute is allowed only if <topology>
element is the only child element of <cpu>
- <cpu> element with 'match' attribute requires <model> element to be
present; <topology> and <feature> elements are optional
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When attaching a USB host device based on vendor/product, libvirt
will resolve the vendor/product into a device/bus pair. This means
that when printing XML we should allow device/bus info to be printed
at any time if present
* src/conf/domain_conf.c, docs/schemas/domain.rng: Allow USB device
bus info alongside vendor/product
Allows the initiator to use a variety of IQNs rather than just the
system IQN when creating iSCSI pools.
* docs/schemas/storagepool.rng: extends the syntax with <iqn name="..."/>
* src/conf/storage_conf.[ch]: read and stores the iqn name
* src/storage/storage_backend_iscsi.[ch]: implement the IQN selection
when detected
The RNG now supports IPv6 and bonds attached to bridges, along with
some other minor tweaks. All test files from netcf have been copied to
the test directory and added to the xml2xml and schema tests (and they
all pass, of course ;-)
Currently CPU topology may only be specified together with CPU model:
<cpu match='exact'>
<model>name</model>
<topology sockets='1' cores='2' threads='3'/>
</cpu>
This patch allows for CPU topology specification without the need for
also specifying CPU model:
<cpu>
<topology sockets='1' cores='2' threads='3'/>
</cpu>
'match' attribute and 'model' element are made optional with the
restriction that 'match' attribute has to be set when 'model' is
present.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Although the serial, parallel, chanel, input & fs devices do
not have PCI address info, they can all have device aliases.
Thus it neccessary to associate the virDomainDeviceInfo data
with them all.
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add hooks for
parsing / formatting device info for serial, parallel, channel
input and fs devices.
* docs/schemas/domain.rng: Associate device info with character
devices, input & fs device
The latter is not officially "wrong", but *is* terribly anachronistic.
I think automake documentation or comments call that syntax obsolescent.
* cfg.mk (_makefile_at_at_check_exceptions): Exempt @SCHEMADIR@
and @SYSCONFDIR@ uses -- there are no Makefile variables for those.
* docs/Makefile.am: Use $(INSTALL), not @INSTALL@.
* examples/dominfo/Makefile.am: Similar.
* examples/domsuspend/Makefile.am: Similar.
* proxy/Makefile.am: Similar.
* python/Makefile.am: Similar.
* python/tests/Makefile.am: Similar.
* src/Makefile.am: Similar.
* tests/Makefile.am: Similar.
This augments virDomainDevice with a <controller> element
that is used to represent disk controllers (e.g., scsi
controllers). The XML format is given by
<controller type="scsi" index="<num>">
<address type="pci" domain="0xNUM" bus="0xNUM" slot="0xNUM"/>
</controller>
where type denotes the disk interface (scsi, ide,...), index
is an integer that identifies the controller for association
with disks, and the <address> element specifies the controller
address on the PCI bus as described in previous commits
The address element can be omitted; in this case, an address
will be assigned automatically.
Most of the code in this patch is from Wolfgang Mauerer's
previous disk controller series
* docs/schemas/domain.rng: Define syntax for <controller>
XML element
* src/conf/domain_conf.c, src/conf/domain_conf.h: Define
virDomainControllerDef struct, and routines for parsing
and formatting XML
* src/libvirt_private.syms: Add virDomainControllerInsert
and virDomainControllerDefFree
Add the virDomainDeviceAddress information to the sound, video
and watchdog devices. This means all of them gain the new XML
element
<address .... />
This brings them upto par with disk/net/hostdev devices which
already have address info
* src/conf/domain_conf.h: Add virDomainDeviceAddress to sound,
video & watchdog device struts.
* src/conf/domain_conf.c: Hook up parsing/formatting for
virDomainDeviceAddress in sound, video & watchdog devices
* docs/schemas/domain.rng: Associate device address info
with sound, video & watchdog
Introduce a new structure
struct _virDomainDeviceDriveAddress {
unsigned int controller;
unsigned int bus;
unsigned int unit;
};
and plug that into virDomainDeviceAddress and generates XML that
looks like
<address type='drive' controller='1' bus='0' unit='5'/>
This syntax will be used by the QEMU driver to explicitly control
how drives are attached to the bus
* src/conf/domain_conf.h, src/conf/domain_conf.c: Parsing and
formatting of drive addresses
* docs/schemas/domain.rng: Define new address format for drives
All guest devices now use a common device address structure
summarized by:
enum virDomainDeviceAddressType {
VIR_DOMAIN_DEVICE_ADDRESS_TYPE_NONE,
VIR_DOMAIN_DEVICE_ADDRESS_TYPE_PCI,
};
struct _virDomainDevicePCIAddress {
unsigned int domain;
unsigned int bus;
unsigned int slot;
unsigned int function;
};
struct _virDomainDeviceInfo {
int type;
union {
virDomainDevicePCIAddress pci;
} addr;
};
This replaces the anonymous structs in Disk/Net/Hostdev data
structures. Where available, the address is *always* printed
in the XML file, instead of being hidden in the internal state
file.
<address type='pci' domain='0x0000' bus='0x1e' slot='0x07' function='0x0'/>
The structure definition is based on Wolfgang Mauerer's disk
controller patch series.
* docs/schemas/domain.rng: Define the <address> syntax and
associate it with disk/net/hostdev devices
* src/conf/domain_conf.h, src/conf/domain_conf.c,
src/libvirt_private.syms: APIs for parsing/formatting address
information. Also remove the QEMU specific 'pci_addr' attributes
* src/qemu/qemu_driver.c: Replace use of 'pci_addr' attrs with
new standardized format.
* docs/Makefile.am (uninstall-local): Separate $$f from preceding
dir name with a "/" and use $$(basename $$f) rather than $$f, since
some values of $$f are prefixed with devhelp/.
The MAC addresses with 00:50:56 prefix are split into several ranges:
00:50:56:00:00:00 - 00:50:56:3f:ff:ff 'static' range (manually assigned)
00:50:56:80:00:00 - 00:50:56:bf:ff:ff 'vpx' range (assigned by a VI Client)
Erroneously the 'vpx' range was assumed to be larger and to occupy the
remaining addresses of the 00:50:56 prefix that are not part of the 'static'
range.
00:50:56 was used as prefix for generated MAC addresses, this is not possible
anymore, because there are gaps in the allowed ranges. Therefore, change the
prefix to 00:0c:29 which is the prefix for auto generated MAC addresses anyway.
Allow arbitrary MAC addresses to be used and set the checkMACAddress VMX option
to false in case the MAC address doesn't fall into any predefined range.
* docs/drvesx.html.in: update website accordingly
* src/esx/esx_driver.c: set the auto generation prefix to 00:0c:29
* src/esx/esx_vmx.c: fix MAC address range handling and allow arbitrary MAC
addresses
* tests/vmx2xml*, tests/xml2vmx*: add some basic MAC address range tests
XML schema for CPU flags
Firstly, CPU topology and model with optional features have to be
advertised in host capabilities:
<host>
<cpu>
<arch>ARCHITECTURE</arch>
<features>
<!-- old-style features are here -->
</features>
<model>NAME</model>
<topology sockets="S" cores="C" threads="T"/>
<feature name="NAME"/>
</cpu>
...
</host>
Secondly, drivers which support detailed CPU specification have to
advertise
it in guest capabilities:
<guest>
...
<features>
<cpuselection/>
</features>
</guest>
And finally, CPU may be configured in domain XML configuration:
<domain>
...
<cpu match="MATCH">
<model>NAME</model>
<topology sockets="S" cores="C" threads="T"/>
<feature policy="POLICY" name="NAME"/>
</cpu>
</domain>
Where MATCH can be one of:
- 'minimum' specified CPU is the minimum requested CPU
- 'exact' disable all additional features provided by host CPU
- 'strict' fail if host CPU doesn't exactly match
POLICY can be one of:
- 'force' turn on the feature, even if host doesn't have it
- 'require' fail if host doesn't have the feature
- 'optional' match host
- 'disable' turn off the feature, even if host has it
- 'forbid' fail if host has the feature
'force' and 'disable' policies turn on/off the feature regardless of its
availability on host. 'force' is unlikely to be used but its there for
completeness since Xen and VMWare allow it.
'require' and 'forbid' policies prevent a guest from being started on a host
which doesn't/does have the feature. 'forbid' is for cases where you disable
the feature but a guest may still try to access it anyway and you don't want
it to succeed.
'optional' policy sets the feature according to its availability on host.
When a guest is booted on a host that has the feature and then migrated to
another host, the policy changes to 'require' as we can't take the feature
away from a running guest.
Default policy for features provided by host CPU but not specified in domain
configuration is set using match attribute of cpu tag. If 'minimum' match is
requested, additional features will be treated as if they were specified
with 'optional' policy. 'exact' match implies 'disable' policy and 'strict'
match stands for 'forbid' policy.
* docs/schemas/capability.rng docs/schemas/domain.rng: extend the
RelaxNG schemas to add CPU flags support
The description mismatched the actual structure since the video element
was introduced. The nvram attribute is actually called vram. Specify the
unit of the vram attribute.
The owner and group in the documentation examples were confusingly given as
'0744'. They should be numeric uid and gid. Changed the examples to use the
default uid and gid assigned to qemu in F12.
* docs/formatstorage.html.in: Change example owner and group in volume XML
Replace free(virBufferContentAndReset()) with virBufferFreeAndReset().
Update documentation and replace all remaining calls to free() with
calls to VIR_FREE(). Also add missing calls to virBufferFreeAndReset()
and virReportOOMError() in OOM error cases.
* docs/ChangeLog.xsl docs/newapi.xsl docs/site.xsl: change all
stylesheets to output UTF-8 HTML instead of ISO Latin 1 which was
breaking on some people names.
Introduce a new type="dir" mode for <disks> that allows use of
QEMU's virtual FAT block device driver. eg
<disk type='dir' device='floppy'>
<source dir='/tmp/test'/>
<target dev='fda' bus='fdc'/>
<readonly/>
</disk>
gets turned into
-drive file=fat:floppy:/tmp/test,if=floppy,index=0
Only read-only disks are supported with virtual FAT mode
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add type="dir"
* docs/schemas/domain.rng: Document new disk type
* src/xen/xend_internal.c, src/xen/xm_internal.c: Raise error for
unsupported disk types
* tests/qemuxml2argvdata/qemuxml2argv-disk-cdrom-empty.args: Fix
empty disk file handling
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.xml,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.xml
tests/qemuxml2argvtest.c: Test QEMU vitual FAT driver
* src/qemu/qemu_conf.c: Support generating fat:/some/dir type
disk args
* src/security/security_selinux.c: Temporarily skip labelling
of directory based disks
0.7.3 was broken
* configure.in docs/news.html.in: release of 0.7.4
* configure.in libvirt.spec.in: require netcf >= 0.1.4
* src/Makefile.am: node_device/node_device_udev.h was missing from
NODE_DEVICE_DRIVER_UDEV_SOURCES breaking compilation on platforms with
udev
For backward compatibility we used to add the tty path as
a tty attribute on console of type pty, duplicating the value
now found in source/@path, but the Relax-NG grammar wasn't
extended for this
<console type='pty' tty='/dev/pts/8'>
<source path='/dev/pts/8'/>
<target port='0'/>
</console>
* docs/schemas/domain.rng: allow an optional tty attribute
containing a devicePath
* docs/drivers.html.in: list the ESX driver
* docs/drvesx.html.in: the new ESX driver documentation
* docs/hvsupport.html.in: add the ESX driver to the matrix
* docs/index.html.in, docs/sitemap.html.in: list the ESX driver
* src/esx/esx_driver.c: fix and cleanup some comments
Debian's /etc/xml/catalog doesn't contain system identifiers, so use
public identifiers instead.
* docs/Makefile.am: use public instead of system identifier
* docs/site.xsl: use matching public identifier
* docs/formatdomain.html.in: refactors the existing character device
documentation to make it explicit which directives configure the guest
interface, and which configure the host interface.
This patch is the result of running the following command in the docs
directory: sed -i 's/\t/ /g; s/\s*$//' *.html.in
* docs/*.html.in:convert tabs into 8 spaces and remove trailing whitespace
* src/internal.h (ATTRIBUTE_SENTINEL): New, it's a ggc feature and
protected as such
* src/util/buf.c (virBufferStrcat): Use it.
* src/util/ebtables.c (ebtablesAddRemoveRule): Use it.
* src/util/iptables.c (iptableAddRemoveRule: Use it.
* src/util/qparams.h (new_qparam_set, append_qparams): Use it.
* docs/apibuild.py: avoid breaking the API generator with that new
internal keyword macro
allows the following to be specified in a domain:
<channel type='pipe'>
<source path='/tmp/guestfwd'/>
<target type='guestfwd' address='10.0.2.1' port='4600'/>
</channel>
* proxy/Makefile.am: add network.c as dep of domain_conf.c
* docs/schemas/domain.rng src/conf/domain_conf.[ch]: extend the domain
schemas and the parsing/serialization side for the new construct
QEmu support will add the following on the qemu command line:
-chardev pipe,id=channel0,path=/tmp/guestfwd
-net user,guestfwd=tcp:10.0.2.1:4600-chardev:channel0
* src/qemu/qemu_conf.c: Add argument output for channel
* tests/qemuxml2(argv|xml)test.c: Add test for <channel> domain syntax
This patch adds an optional attribute to the <bootp> tag, that
allows to specify a TFTP server address other than the address of
the DHCP server itself.
This can be used to forward the BOOTP settings of the host down to the
guest. This is something that configurations such as Xen's default
network achieve naturally, but must be done manually for NAT.
* docs/formatnetwork.html.in: Document new attribute.
* docs/schemas/network.rng: Add it to schema.
* src/conf/network_conf.h: Add it to struct.
* src/conf/network_conf.c: Add it to parser and pretty printer.
* src/network/bridge_driver.c: Put it in the dnsmasq command line.
* tests/networkxml2xmlin/netboot-proxy-network.xml
tests/networkxml2xmlout/netboot-proxy-network.xml
tests/networkxml2xmltest.c: add new tests
* src/conf/storage_conf.c src/conf/storage_conf.h: extend the enums
and values
* docs/schemas/storagepool.rng: add to the list of storage pool type
formats
- mpath pools weren't listed
- scsi pools were missing an adapter section
- iscsi pools were missing an auth section
- Logical pools do not require a source name to be specified
The domain/os/type element may have an arch specified without having
a machine variant specified. In fact, this is what python-virtinst
does when defining a guest.
* docs/schemas/domain.rng: allow missing machine type
Removes some auto-generated files still under version control.
It also moves the rule for generating NEWS into the Makefile.am
that's in the same directory as the output file to avoid confusion
* docs/libvirt-api.xml, docs/libvirt-refs.xml, NEWS: Remove
auto-generated files from source control
* Makefile.am: Add rule for generating NEWS file
* docs/Makefile.am: Remove rule for generating NEWS file
Simplify the doTunnelMigrate() method by pulling out the code
which opens/closes the virConnectPtr object into a parent
method
* qemu/qemu_driver.c: Add doPeer2PeerMigrate which then calls
doTunnelMigrate with dconn & dom_xml
* docs/drvqemu.html.in: include documentation for AppArmor sVirt
confinement
* examples/apparmor/TEMPLATE examples/apparmor/libvirt-qemu
examples/apparmor/usr.lib.libvirt.virt-aa-helper
examples/apparmor/usr.sbin.libvirtd: example templates and
configuration files for SVirt Apparmor when using KVM/QEmu
The devhelp/ directory files depend on libvirt-api.xml being
uptodate, but automake always processes SUBDIRS before the
current directory. So devhelp would be built and then the
libvirt-api.xml re-build, invalidating the devhelp data again.
To fix this all the rules for devhelp are moved directly
into the docs/Makefile.am allowing make to see the global
dependancy chain and thus build things in the correct order
* docs/Makefile.am: Add rules for devhelp rebuild
* docs/devhelp/Makefile.am: Remove devhelp rebuild
* configure.in: Remove docs/devhelp/Makefile.am
Implementation of tunnelled migration, using a Unix Domain Socket
on the qemu backend. Note that this requires very new versions of
qemu (0.10.7 at least) in order to get the appropriate bugfixes.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
* docs/schemas/domain.rng: allow one <description> tag in the top level
of the <domain> to store user information as text
* src/conf/domain_conf.c src/conf/domain_conf.h: extend the structure
to store this text, grab it at parse time and save it back when
present after <uuid>
Function comments for virStreamEvent{Add,Update,Remove}Callback() are
missing a trailing ':'. Therefore apibuild.py fails to parse the comment
and warns about the missing ':'.
* docs/libvirt-api.xml, docs/libvirt-refs.xml: updated by apibuild.py
* src/libvirt.c: add missing ':' in function comments
* include/libvirt/libvirt.h.in: Public API contract for
virStreamPtr object
* src/libvirt_public.syms: Export data stream APIs
* src/libvirt_private.syms: Export internal helper APIs
* src/libvirt.c: Data stream API driver dispatch
* src/datatypes.h, src/datatypes.c: Internal helpers for virStreamPtr
object
* src/driver.h: Define internal driver API for streams
* .x-sc_avoid_write: Ignore src/libvirt.c because it trips
up on comments including write()
* python/Makefile.am: Add libvirt-override-virStream.py
* python/generator.py: Add rules for virStreamPtr class
* python/typewrappers.h, python/typewrappers.c: Wrapper
for virStreamPtr
* docs/libvirt-api.xml, docs/libvirt-refs.xml: Regenerate
with new APIs
The python method help docs are copied across from the C
funtion comments, but in the process all line breaks and
indentation was being lost. This made the resulting text
and code examples completely unreadable. Both the API
doc extractor and the python generator were destroying
whitespace & this fixes them to preserve it exactly.
* docs/apibuild.py: Preserve all whitespace when extracting
function comments. Print function comment inside a <![CDATA[
section to fully preserve all whitespace. Look for the
word 'returns' to describe return values, instead of 'return'
to avoid getting confused with code examples including the
C 'return' statement.
* python/generator.py: Preserve all whitespace when printing
function help docs
* src/libvirt.c: Change any return parameter indicated by
'return' to be 'returns', to avoid confusing the API extractor
* docs/libvirt-api.xml: Re-build for fixed descriptions
Currently, libvirtd will start a dnsmasq process for the virtual
network, but (aside from killing the dnsmasq process and replacing it),
there's no way to define tftp boot options.
This change introduces the appropriate tags to the dhcp configuration:
<network>
<name>default</name>
<bridge name="virbr%d" />
<forward/>
<ip address="192.168.122.1" netmask="255.255.255.0">
<tftp root="/var/lib/tftproot" />
<dhcp>
<range start="192.168.122.2" end="192.168.122.254" />
<bootp file="pxeboot.img"/>
</dhcp>
</ip>
</network>
When the attributes are present, these are passed to the
arguments to dnsmasq:
dnsmasq [...] --enable-tftp --tftp-root /srv/tftp --dhcp-boot pxeboot.img
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^^
from <tftp /> from <bootp />
At present, only local tftp servers are supported (ie, dnsmasq runs as
the tftp server), but we could improve this in future by adding a
server= attribute.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2009-09-21 Paolo Bonzini <pbonzini@redhat.com>
Jeremy Kerr <jk@ozlabs.org>
* docs/formatnetwork.html.in: Document new tags.
* docs/formatnetwork.html: Regenerate.
* docs/schemas/network.rng: Update.
* src/network_conf.c (virNetworkDefFree): Free new fields.
(virNetworkDHCPRangeDefParseXML): Parse <bootp>.
(virNetworkIPParseXML): New, parsing <dhcp> and <tftp>.
(virNetworkDefParseXML): Use virNetworkIPParseXML instead of
virNetworkDHCPRangeDefParseXML.
(virNetworkDefFormat): Pretty print new fields.
* src/network_conf.h (struct _virNetworkDef): Add netboot fields.
* src/network_driver.c (networkBuildDnsmasqArgv): Add
TFTP and BOOTP arguments.
* tests/Makefile.am (EXTRA_DIST): Add networkschemadata.
* tests/networkschematest: Look in networkschemadata.
* tests/networkschemadata/netboot-network.xml: New.
* docs/storage/: Move to examples/xml/storage/
* docs/test*.xml: Move to examples/xml/test/
* docs/Makefile.am: Remove example XML files from dist
* Makefile.am: Add examples/xml to EXTRA_DIST
* tests/virshtest.c: Update for moved test XML
* libvirt.spec.in: Include example XML files as docs
* tests/int-overflow: UPdate for moved XML
* docs/*.html, docs/devhelp/*.html, docs/html/*.html: Delete
* docs/.gitignore, docs/devhelp/.gitignore, docs/html/.gitignore:
Ignore generated docs files
* docs/Makefile.am: Rebuild all HTML docs for 'all' target
and include them in EXTRA_DIST and CLEANFILES
* docs/devhelp/Makefile.am: Include HTML in CLEANFILES
* docs/pki_check.sh: Move to tool/virt-pki-validate.in and add
in POD man page documentation
* tools/.gitignore: Ignore generated virt-pki-validate file
* tools/Makefile.am: Install & build virt-pki-validate and
virt-pki-validate.1
* docs/remote.html, docs/remote.html.in: Refer to new tool
name virt-pki-validate
* libvirt.spec.in, mingw32-libvirt.spec.in: Add virt-pki-validate
and virt-pki-validate.1 to files list
* Makefile.am: Add examples/dominfo examples/domsuspend examples/python
as SUBDIRS
* configure.in: Update AC_OUTPUT for new/old Makefiles
* docs/Makefile.am: Remove examples from SUBDIRS
* docs/examples/info1.c: Move to examples/dominfo/info1.c
* docs/examples/suspend.c: Move to examples/domsuspend/suspend.c
* docs/examples: Remove all remaining files
* docs/examples/python: Moved to examples/python/
* examples/dominfo/Makefile.am, examples/domsuspend/Makefile.am: New
build files
* libvirt.spec.in: Update to take account of moved examples
Move the virsh tool and its man page into the tools directory
* Makefile.am: Remove rules for virsh.1 man page
* virsh.1: Remove auto-generated file
* docs/Makefile.am: Remove rules for virsh.pod man page
* docs/virsh.pod: Move to tools/ directory
* src/Makefile.am, src/.gitignore: Remove rules for virsh
* src/console.c, src/console.h, src/*.ico, src/virsh_win_icon.rc,
src/virsh.c: Move into tools/ directory
* tools/Makefile.am: Add rules for building virsh
* tools/.gitignore: Ignore virsh built files
* tests/virshtest.c, tests/int-overflow: Update for new
virsh location
Convert all the secret/storage encryption APIs / wire format to
handle UUIDs in raw format instead of non-canonical printable
format. Guarentees data format correctness.
* docs/schemas/storageencryption.rng: Make UUID mandatory for a secret
and validate fully
* docs/schemas/secret.rng: Fully validate UUID
* include/libvirt/libvirt.h, include/libvirt/libvirt.h.in, Add
virSecretLookupByUUID and virSecretGetUUID. Make
virSecretGetUUIDString follow normal API design pattern
* python/generator.py: Skip generation of virSecretGetUUID,
virSecretGetUUIDString and virSecretLookupByUUID
* python/libvir.c, python/libvirt-python-api.xml: Manual impl
of virSecretGetUUID,virSecretGetUUIDString and virSecretLookupByUUID
* qemud/remote.c: s/virSecretLookupByUUIDString/virSecretLookupByUUID/
Fix get_nonnull_secret/make_nonnull_secret to use unsigned char
* qemud/remote_protocol.x: Fix remote_nonnull_secret to use a
remote_uuid instead of remote_nonnull_string for UUID field.
Rename REMOTE_PROC_SECRET_LOOKUP_BY_UUID_STRING to
REMOTE_PROC_SECRET_LOOKUP_BY_UUID_STRING and make it take an
remote_uuid value
* qemud/remote_dispatch_args.h, qemud/remote_dispatch_prototypes.h,
qemud/remote_dispatch_ret.h, qemud/remote_dispatch_table.h,
qemud/remote_protocol.c, qemud/remote_protocol.h: Re-generate
* src/datatypes.h, src/datatypes.c: Store UUID in raw format instead
of printable. Change virGetSecret to use raw format UUID
* src/driver.h: Rename virDrvSecretLookupByUUIDString to
virDrvSecretLookupByUUID and use raw format UUID
* src/libvirt.c: Add virSecretLookupByUUID and virSecretGetUUID
and re-implement virSecretLookupByUUIDString and
virSecretGetUUIDString in terms of those
* src/libvirt_public.syms: Add virSecretLookupByUUID and
virSecretGetUUID
* src/remote_internal.c: Rename remoteSecretLookupByUUIDString
to remoteSecretLookupByUUID. Fix typo in args for
remoteSecretDefineXML impl. Use raw UUID format for
get_nonnull_secret and make_nonnull_secret
* src/storage_encryption_conf.c, src/storage_encryption_conf.h:
Storage UUID in raw format, and require it to be present in
XML. Use UUID parser to validate.
* secret_conf.h, secret_conf.c: Generate a UUID if none is provided.
Storage UUID in raw format.
* src/secret_driver.c: Adjust to deal with raw UUIDs. Save secrets
in a filed with printable UUID, instead of base64 UUID.
* src/virsh.c: Adjust for changed public API contract of
virSecretGetUUIDString.
* src/storage_Backend.c: DOn't undefine secret we just generated
upon successful volume creation. Fix to handle raw UUIDs. Generate
a non-clashing UUID
* src/qemu_driver.c: Change to use lookupByUUID instead of
lookupByUUIDString
* docs/schemas/domain.rng: Add <serial> element to disks
* src/domain_conf.h, src/domain_conf.c: XML parsing and
formatting for disk serial numbers
* src/qemu_conf.c: Set serial number when launching guests
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-shared.args,
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-shared.xml: Add
serial number to XML test
Add option to domain XML for
<memoryBacking>
<hugepages/>
</memoryBacking>
* configure.in: Add check for mntent.h
* qemud/libvirtd_qemu.aug, qemud/test_libvirtd_qemu.aug, src/qemu.conf
Add 'hugetlbfs_mount' config parameter
* src/qemu_conf.c, src/qemu_conf.h: Check for -mem-path flag in QEMU,
and pass it when hugepages are requested.
Load hugetlbfs_mount config parameter, search for mount if not given.
* src/qemu_driver.c: Free hugetlbfs_mount/path parameter in driver shutdown.
Create directory for QEMU hugepage usage, chowning if required.
* docs/formatdomain.html.in: Document memoryBacking/hugepages elements
* docs/schemas/domain.rng: Add memoryBacking/hugepages elements to schema
* src/util.c, src/util.h, src/libvirt_private.syms: Add virFileFindMountPoint
helper API
* tests/qemuhelptest.c: Add -mem-path constants
* tests/qemuxml2argvtest.c, tests/qemuxml2xmltest.c: Add tests for hugepage
handling
* tests/qemuxml2argvdata/qemuxml2argv-hugepages.xml,
tests/qemuxml2argvdata/qemuxml2argv-hugepages.args: Data files for
hugepage tests
* docs/schemas/domain.rng: augment the video model with an optional
acceleration element with optional accel2d and accel3d flags
* src/domain_conf.c src/domain_conf.h: exten the virDomainVideoDef
structure with an optional accel field, virDomainVideoAccelDefParseXML
and virDomainVideoAccelDefFormat functions to parse and serialize
the structure.
The XML allows <encryption format='unencrypted'/>, this implementation
canonicalizes the internal representation so that "disk->encryption" is
non-NULL iff encryption information is available.
A domain with partial encryption information can be defined,
completeness of the information is not verified. The domain won't
start until the remaining information is added, of course.
* docs/formatdomain.html, docs/formatdomain.html.in: Document
new encryption options for disks
* docs/schemas/domain.rng: Pull in storage encryption schema
rules
* src/domain_conf.h, src/domain_conf.c: Wire up storage encryption
XML parsing/formatting APIs
The XML allows <encryption format='unencrypted'/>, this implementation
canonicalizes the internal representation so that "vol->encryption" is
non-NULL iff the volume is encrypted.
Note that partial encryption information (e.g. specifying an encryption
format, but not the key/passphrase) is valid, libvirt will automatically
choose value for the missing information during volume creation. The
user can read the volume XML, and use the unmodified <encryption> tag in
future operations (without having to be able to understand) its contents.
* docs/formatstorage.html, docs/formatstorage.html.in: Document
storage volume encryption options
* src/storage_conf.c, src/storage_conf.h: Hook up storage
encryption XML handling
* tests/storagevolschemadata/vol-qcow2.xml: Test case for encryption
schema changes
Define an <encryption> tag specifying volume encryption format and
format-depenedent parameters (e.g. passphrase, cipher name, key
length, key).
Currently the only defined parameter is a reference to a "secret"
(passphrase/key) managed using the virSecret* API.
Only the qcow/qcow2 encryption format, and a "default" format used to
let libvirt choose the format during volume creation, is currently
supported.
This patch does not add any users; the <encryption> tag is added in
the following patches to both volumes (to support encrypted volume
creation) and domains.
* docs/*.html: Re-generate
* docs/formatstorageencryption.html.in, docs/sitemap.html.in:
Add page describing storage encryption data format
* docs/schemas/Makefile.am, docs/schemas/storageencryption.rng:
Add RNG schema for storage encryption format
* po/POTFILES.in: Add src/storage_encryption_conf.c
* src/libvirt_private.syms: Export virStorageEncryption* functions
* src/storage_encryption_conf.h, src/storage_encryption_conf.c: Internal
helper APIs for dealing with storage encryption format
* libvirt.spec.in, mingw32-libvirt.spec.in: Add storageencryption.rng
RNG schema
This patch adds a "secret" as a separately managed object, using a
special-purpose API to transfer the secret values between nodes and
libvirt users.
* docs/schemas/secret.rng, docs/schemas/Makefilem.am: Add new
schema for virSecret objects
* docs/*html: Re-generated
* docs/formatsecret.html.in, docs/sitemap.html.in: Add page
describing the virSecret XML schema
* include/libvirt/libvirt.h.in: Define the new virSecret public
API
* src/libvirt_public.syms: Export symbols for new public APIs
* mingw32-libvirt.spec.in, libvirt.spec.in: Add secret.rng to
files list
The documentation for virNodeGetCellsFreeMemory claims the values
returned are in kilobytes, but that's actually wrong; the value
returned is actually in bytes. Fix up the documentation to be
correct.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
e.g. <machine canonical='pc'>pc-0.11</machine>
* src/capabilities.c: output the canonical machine names in the
capabilities output, if available
* docs/schemas/capabilities.rng: add the new attribute
