On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
q35 machines have an implicit ahci (sata) controller at 00:1F.2 which
has no "id" associated with it. For this reason, we can't refer to it
as "ahci0". Instead, we don't give an id on the commandline, which
qemu interprets as "use the first ahci controller". We then need to
specify the unit with "unit=%d" rather than adding it onto the bus
arg.
We had been setting the device alias in the devinceinfo for pci
controllers to "pci%u", but then hardcoding "pci.%u" when creating the
device address for other devices using that pci bus. This all worked
just fine until we encountered the built-in "pcie.0" bus (the PCIe
root complex) in Q35 machines.
In order to create the correct commandline for this one case, this
patch:
1) sets the alias for PCI controllers correctly, to "pci.%u" (or
"pcie.%u" for the pcie-root controller)
2) eliminates the hardcoded "pci.%u" for pci controllers when
generatuing device address strings, and instead uses the controller's
alias.
3) plumbs a pointer to the virDomainDef all the way down to
qemuBuildDeviceAddressStr. This was necessary in order to make the
aliase of the controller *used by a device* available (previously
qemuBuildDeviceAddressStr only had the deviceinfo of the device
itself, *not* of the controller it was connecting to). This made for a
larger than desired diff, but at least in the future we won't have to
do it again, since all the information we could possibly ever need for
future enhancements is in the virDomainDef. (right?)
This should be done for *all* controllers, but for now we just do it
in the case of PCI controllers, to reduce the likelyhood of
regression.
This patch adds in special handling for a few devices that need to be
treated differently for q35 domains:
usb - there is no implicit/default usb controller for the q35
machinetype. This is done because normally the default usb controller
is added to a domain by just adding "-usb" to the qemu commandline,
and it's assumed that this will add a single piix3 usb1 controller at
slot 1 function 2. That's not what happens when the machinetype is
q35, though. Instead, adding -usb to the commandline adds 3 usb
(version 2) controllers to the domain at slot 0x1D.{1,2,7}. Rather
than having
<controller type='usb' index='0'/>
translate into 3 separate devices on the PCI bus, it's cleaner to not
automatically add a default usb device; one can always be added
explicitly if desired. Or we may decide that on q35 machines, 3 usb
controllers will be automatically added when none is given. But for
this initial commit, at least we aren't locking ourselves into
something we later won't want.
video - qemu always initializes the primary video device immediately
after any integrated devices for the machinetype. Unless instructed
otherwise (by using "-device vga..." instead of "-vga" which libvirt
uses in many cases to work around deficiencies and bugs in various
qemu versions) qemu will always pick the first unused slot. In the
case of the "pc" machinetype and its derivatives, this is always slot
2, but on q35 machinetypes, the first free slot is slot 1 (since the
q35's integrated peripheral devices are placed in other slots,
e.g. slot 0x1f). In order to make the PCI address of the video device
predictable, that slot (1 or 2, depending on machinetype) is reserved
even when no video device has been specified.
sata - a q35 machine always has a sata controller implicitly added at
slot 0x1F, function 2. There is no way to avoid this controller, so we
always add it. Note that the xml2xml tests for the pcie-root and q35
cases were changed to use DO_TEST_DIFFERENT() so that we can check for
the sata controller being automatically added. This is especially
important because we can't check for it in the xml2argv output (it has
no effect on that output since it's an implicit device).
ide - q35 has no ide controllers.
isa and smbus controllers - these two are always present in a q35 (at
slot 0x1F functions 0 and 3) but we have no way of modelling them in
our config. We do need to reserve those functions so that the user
doesn't attempt to put anything else there though. (note that the "pc"
machine type also has an ISA controller, which we also ignore).
This PCI controller, named "dmi-to-pci-bridge" in the libvirt config,
and implemented with qemu's "i82801b11-bridge" device, connects to a
PCI Express slot (e.g. one of the slots provided by the pcie-root
controller, aka "pcie.0" on the qemu commandline), and provides 31
*non-hot-pluggable* PCI (*not* PCIe) slots, numbered 1-31.
Any time a machine is defined which has a pcie-root controller
(i.e. any q35-based machinetype), libvirt will automatically add a
dmi-to-pci-bridge controller if one doesn't exist, and also add a
pci-bridge controller. The reasoning here is that any useful domain
will have either an immediate (startup time) or eventual (subsequent
hot-plug) need for a standard PCI slot; since the pcie-root controller
only provides PCIe slots, we need to connect a dmi-to-pci-bridge
controller to it in order to get a non-hot-plug PCI slot that we can
then use to connect a pci-bridge - the slots provided by the
pci-bridge will be both standard PCI and hot-pluggable.
Since pci-bridge devices themselves can not be hot-plugged into a
running system (although you can hot-plug other devices into a
pci-bridge's slots), any new pci-bridge controller that is added can
(and will) be plugged into the dmi-to-pci-bridge as long as it has
empty slots available.
This patch is also changing the qemuxml2xml-pcie test from a "DO_TEST"
to a "DO_DIFFERENT_TEST". This is so that the "before" xml can omit
the automatically added dmi-to-pci-bridge and pci-bridge devices, and
the "after" xml can include it - this way we are testing if libvirt is
properly adding these devices.
