This resolves one of the issues listed in:
https://bugzilla.redhat.com/show_bug.cgi?id=1003983
00:1E.0 is the location of this controller on at least some actual Q35
hardware, so we try to replicate the placement. The bridge should work
just as well in any other location though, so if 00:1E.0 isn't
available, just allow it to be auto-assigned anywhere appropriate.
This resolves one of the issues in:
https://bugzilla.redhat.com/show_bug.cgi?id=1003983
This device is identical to qemu's "intel-hda" device (known as "ich6"
in libvirt), but has a different PCI device ID (which matches the ID
of the hda audio built into the ich9 chipset, of course). It's not
supported in earlier versions of qemu, so it requires a capability
bit.
The testutils.c file had some fprintfs which had not been
converted from %d to %zu, when 'testCounter' change to be
a size_t. This was a build breaker if --enable-test-oom
was enabled
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Start a test case for the virNetServerClient object, which
initially checks the creation of a virIdentityPtr object.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This splits up the version parsing code into a callable API like QEMU
help/version string parsing so that we can test it as we need to add
additional patterns for newer versions/products.
Coverity complains that the test suite did not check the
return value of dbus_message_iter_append_basic() as we did
in most other places.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This resolves https://bugzilla.redhat.com/show_bug.cgi?id=1008903
The Q35 machinetype has an implicit SATA controller at 00:1F.2 which
isn't given the "expected" id of ahci0 by qemu when it's created. The
original suggested solution to this problem was to not specify any
controller for the disks that use the default controller and just
specify "unit=n" instead; qemu should then use the first IDE or SATA
controller for the disk.
Unfortunately, this "solution" is ignorant of the fact that in the
case of SATA disks, the "unit" attribute in the disk XML is actually
*not* being used for the unit, but is instead used to specify the
"bus" number; each SATA controller has 6 buses, and each bus only
allows a single unit. This makes it nonsensical to specify unit='n'
where n is anything other than 0. It also means that the only way to
connect more than a single device to the implicit SATA controller is
to explicitly give the bus names, which happen to be "ide.$n", where
$n can be replaced by the disk's "unit" number.
This macro is there to test the simplest monitor functions we have,
those in the form of: int ( *func) (qemuMonitorPtr). So far, we have
seven such functions.
Useful to set custom forwarders instead of using the contents of
/etc/resolv.conf. It helps me to setup dnsmasq as local nameserver to
resolve VM domain names from domain 0, when domain option is used.
Signed-off-by: Diego Woitasen <diego.woitasen@vhgroup.net>
Signed-off-by: Eric Blake <eblake@redhat.com>
A user was having an issue with this specific VMWare Fusion config and
he gave me permission to add it as part of our test suite to further
expand our VMX test coverage. Unfortunately our VMX parser and
generator does not support many features contained within and just
silently ignores fields it does not understand so they had to
be removed out in the xml2vmx test. The original unmodified version
exists in the vmx2xml test.
VMWare Fusion 5 can set the CD-ROM's device name to be 'auto detect' when
using the physical drive via 'cdrom-raw' device type. VMWare will then
connect to first available host CD-ROM to the virtual machine upon start
up according to VMWare documentation. If no device is available, it
appears that the device will remain disconnected.
To better model this a CD-ROM that is marked as "auto detect" when in
the off state would be modeled as the following with this patch:
<disk type='block' device='lun'>
<source startupPolicy='optional'/>
<target dev='hda' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
Once the domain transitions to the powered on state, libvirt can
populate the remaining source data with what is connected, if anything.
However future power cycles, the domain may not always start with that
device attached.
A cross build to mingw fails with:
CC virsystemdtest-virsystemdtest.o
../../tests/virsystemdtest.c: In function 'testCreateNoSystemd':
../../tests/virsystemdtest.c:97:9: error: implicit declaration of function 'unsetenv' [-Werror=implicit-function-declaration]
unsetenv("FAIL_NO_SERVICE");
^
../../tests/virsystemdtest.c:97:9: error: nested extern declaration of 'unsetenv' [-Werror=nested-externs]
We could cop out and pull in the gnulib unsetenv module. But when
you stop and think about it, this test requires LD_PRELOAD to work,
and systemd is a Linux-only concept anyways, both of which mean
the test could never work on mingw in the first place. Simpler is
to just fix the test to behave like our other LD_PRELOAD tests.
* tests/virsystemdtest.c: Provide non-Linux implementation.
Signed-off-by: Eric Blake <eblake@redhat.com>
Multiple tests need to register a function to quiesce errors from
libvirt when using a connection and doing negative tests. Each of those
tests had a static function to do so. This can be replaced by a utility
function that enables the errors when debug is enabled.
This patch adds virtTestQuiesceLibvirtErrors() and refactors test that
use private handlers.
qemu/KVM also supports a tftp URL while specifying the cdrom ISO image.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='tftp' name='/url/path'>
<host name='host.name' port='69'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
The ftps protocol is another protocol supported by qemu/KVM while specifying
the cdrom ISO image.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='ftps' name='/url/path'>
<host name='host.name' port='990'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
The https protocol is also accepted by qemu/KVM when specifying the cdrom ISO
image.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='https' name='/url/path'>
<host name='host.name' port='443'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
Debian systems may run the 'systemd-logind' daemon, which causes the
/sys/fs/cgroup/systemd mount to be setup, but no other cgroup
controllers are created. While the LXC driver considers cgroups to
be mandatory, the QEMU driver is supposed to accept them as optional.
We detect whether they are present by looking in /proc/mounts for
any mounts of type 'cgroups', but this is not sufficient. We need to
skip any named mounts (as seen by a name=XXX string in the mount
options), so that we only detect actual resource controllers.
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=721979
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The change to query org.freedesktop.DBus.ListActivatableNames
to detect systemd broke the test suite, since we did not have
stubs to respond to this dbus call.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Commit ef5d51d fixed a crash for numatune with auto placement and
nodeset specified:
<numatune>
<memory mode='preferred' placement='auto' nodeset='0'/>
</numatune>
Some users in Ubuntu/Debian seem to have a setup where all the
cgroup controllers are mounted on /sys/fs/cgroup rather than
any /sys/fs/cgroup/<controller> name. In the loop which detects
which controllers are present for a mount point we were modifying
'mnt_dir' field in the 'struct mntent' var, but not always restoring
the original value. This caused detection to break in the all-in-one
mount setup.
Fix that logic bug and add test case coverage for this mount
setup.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
If we use subdir-objects with automake, any reference to a
cross-directory .c file will result in automake creating
rules that track dependency in the cross directory. But this
presents a problem during 'make distclean' - if the cross
directory is cleaned up first, then the daemon directory will
be left with dangling references to .Po dependency files that
no longer exist.
Meanwhile, referring to the cross-directory .c file means
that we are compiling the file twice - once in src, and once
in daemon. Better is to compile just once in src into a
convenience library, and then use that library from daemon.
The tests directory had a similar situation of a cross-directory
.c file; to solve that, we actually need a convenience library.
* daemon/Makefile.am (DAEMON_SOURCES): Drop .c files...
(libvirtd_LDADD): ...and instead use library.
(libvirtd_conf_la_SOURCES): Declare a new convenience library.
(libvirtd_LDFLAGS): Drop duplicate flag.
* tests/Makefile.am (libvirtdconftest_SOURCES): Drop .c file...
(libvirtdconftest_LDADD): ..and instead use library.
Signed-off-by: Eric Blake <eblake@redhat.com>
Commits 905629f4 and 1716e7a6 have added support for specifying
an IPv4 range and a port range to be used by NAT:
<forward mode='nat'>
<nat>
<address start='10.20.30.40' end='10.20.30.44'/>
<port start='60000' end='65432'/>
</nat>
</forward>
https://bugzilla.redhat.com/show_bug.cgi?id=1004364
An rpm build with client_only set to 1 (for example, RHEL 5 on
s390, or by modifying libvirt.spec.in) failed with
TEST: fdstreamtest
1) Stream read blocking ... OK
2) Stream read non-blocking ... Unexpected EOF block 0 want 128
FAILED
3) Stream write blocking ... OK
4) Stream write non-blocking ... Failed to finish stream: internal error: libvirt: error : cannot execute binary /home/eblake/rpmbuild/BUILD/libvirt-1.1.1/tests/../src/libvirt_iohelper: No such file or directory
Since the test depends on something that was only built for
WITH_LIBVIRTD (see src/Makefile.am), we must do the same for
the test.
* tests/Makefile.am (test_programs): Make fdstreamtest conditional.
Signed-off-by: Eric Blake <eblake@redhat.com>
Automake has builtin support to prevent botched conditional nesting,
but only if you use:
if FOO
else !FOO
endif !FOO
An example error message when using the wrong name:
daemon/Makefile.am:378: error: else reminder (LIBVIRT_INIT_SCRIPT_SYSTEMD_TRUE) incompatible with current conditional: LIBVIRT_INIT_SCRIPT_SYSTEMD_FALSE
daemon/Makefile.am:381: error: endif reminder (LIBVIRT_INIT_SCRIPT_SYSTEMD_TRUE) incompatible with current conditional: LIBVIRT_INIT_SCRIPT_SYSTEMD_FALSE
As our makefiles tend to have quite a bit of nested conditionals,
it's better to take advantage of the benefits of the build system
double-checking that our conditionals are well-nested, but that
requires a syntax check to enforce our usage style.
Alas, unlike C preprocessor and spec files, we can't use indentation
to make it easier to see how deeply nesting goes.
* cfg.mk (sc_makefile_conditionals): New rule.
* daemon/Makefile.am: Enforce the style.
* gnulib/tests/Makefile.am: Likewise.
* python/Makefile.am: Likewise.
* src/Makefile.am: Likewise.
* tests/Makefile.am: Likewise.
* tools/Makefile.am: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
According to VMWare's documentation 'cdrom-raw' is an acceptable value
for deviceType for a CD-ROM drive. The documentation states that the VMX
configuration for a CD-ROM deviceType is as follows:
ide|scsi(n):(n).deviceType = "cdrom-raw|atapi-cdrom|cdrom-image"
From the documentation it appears the following is true:
- cdrom-image = Provides the ISO to the VM
- atapi-cdrom = Provides a NEC emulated ATAPI CD-ROM on top of the host
CD-ROM
- cdrom-raw = Passthru for a host CD-ROM drive. Allows CD-R burning from
within the guest.
A CD-ROM prior to this patch would always provide an 'atapi-cdrom' is
modeled as:
<disk type='block' device='cdrom'>
<source dev='/dev/scd0'/>
<target dev='hda' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
This patch allows the 'device' attribute to be set to 'lun' for a raw
acccess CD-ROM such as:
<disk type='block' device='lun'>
<source dev='/dev/scd0'/>
<target dev='hda' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
Starting with qemu 1.6, the qemu-system-arm vexpress-a9 model has a
hardcoded virtio-mmio transport which enables attaching all virtio
devices.
On the command line, we have to use virtio-XXX-device rather than
virtio-XXX-pci, thankfully s390 already set the precedent here so
it's fairly straight forward.
At the XML level, this adds a new device address type virtio-mmio.
The controller and addressing don't have any subelements at the
moment because we they aren't needed for this usecase, but could
be added later if needed.
Add a test case for an ARM guest with one of every virtio device
enabled.
Similar to the chardev bit, ARM boards depend on the old style '-net nic'
for actually instantiating net devices. But we can't block out
-netdev altogether since it's needed for upcoming virtio support.
And add tests for working ARM XML with console, disk, and networking.
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
Add an attribute named 'removable' to the 'target' element of disks,
which controls the removable flag. For instance, on a Linux guest it
controls the value of /sys/block/$dev/removable. This option is only
valid for USB disks (i.e. bus='usb'), and its default value is 'off',
which is the same behaviour as before.
To achieve this, 'removable=on' (or 'off') is appended to the '-device
usb-storage' parameter sent to qemu when adding a USB disk via
'-disk'. A capability flag QEMU_CAPS_USB_STORAGE_REMOVABLE was added
to keep track if this option is supported by the qemu version used.
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=922495
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Allow use of the usb-storage device only if the new capability flag
QEMU_CAPS_DEVICE_USB_STORAGE is set, which it is for qemu(-kvm)
versions >= 0.12.1.2-rhel62-beta.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Ubuntu libdbus.so links with -Bsymbolic-functions, which means
that we can only LD_PRELOAD functions that we directly call.
Functions which libdbus.so calls internally can not be replaced.
Thus we cannot use dbus_message_new_error or dbus_message_new_method_return
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
QEMU commit 3984890 introduced the "pci-hole64-size" property,
to i440FX-pcihost and q35-pcihost with a default setting of 2 GB.
Translate <pcihole64>x<pcihole64/> to:
-global q35-pcihost.pci-hole64-size=x for q35 machines and
-global i440FX-pcihost.pci-hole64-size=x for i440FX-based machines.
Error out on other machine types or if the size was specified
but the pcihost device lacks 'pci-hole64-size' property.
https://bugzilla.redhat.com/show_bug.cgi?id=990418
<controller type='pci' index='0' model='pci-root'>
<pcihole64 unit='KiB'>1048576</pcihole64>
</controller>
It can be used to adjust (or disable) the size of the 64-bit
PCI hole. The size attribute is in kilobytes (different unit
can be specified on input), but it gets rounded up to
the nearest GB by QEMU.
Disabling it will be needed for guests that crash with the
64-bit PCI hole (like Windows XP), see:
https://bugzilla.redhat.com/show_bug.cgi?id=990418
The ftp protocol is already recognized by qemu/KVM so add this support to
libvirt as well.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='ftp' name='/url/path'>
<host name='host.name' port='21'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
QEMU/KVM already allows a HTTP URL for the cdrom ISO image so add this support
to libvirt as well.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='http' name='/url/path'>
<host name='host.name' port='80'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
qemu-img is going to switch the default for QCOW2
to QCOW2v3 (compat=1.1)
Extend the probing for qemu-img command line options to check
if -o compat is supported. If the volume definition specifies
the qcow2 format but no compat level and -o compat is supported,
specify -o compat=0.10 to create a QCOW2v2 image.
https://bugzilla.redhat.com/show_bug.cgi?id=997977
