https://bugzilla.redhat.com/show_bug.cgi?id=648855 mentioned a
misuse of 'an' where 'a' is proper; that has since been fixed,
but a search found other problems (some were a spelling error for
'and', while most were fixed by 'a').
* daemon/stream.c: Fix grammar.
* src/conf/domain_conf.c: Likewise.
* src/conf/domain_event.c: Likewise.
* src/esx/esx_driver.c: Likewise.
* src/esx/esx_vi.c: Likewise.
* src/rpc/virnetclient.c: Likewise.
* src/rpc/virnetserverprogram.c: Likewise.
* src/storage/storage_backend_fs.c: Likewise.
* src/util/conf.c: Likewise.
* src/util/dnsmasq.c: Likewise.
* src/util/iptables.c: Likewise.
* src/xen/xen_hypervisor.c: Likewise.
* src/xen/xend_internal.c: Likewise.
* src/xen/xs_internal.c: Likewise.
* tools/virsh.c: Likewise.
The next patch will make it possible to have virDomainSetBlkioParameters
leave device weights unchanged if they are not mentioned in the incoming
string, but this only works if the list of block weights does not allow
duplicate paths. Technically, a user can still confuse libvirt by
passing alternate spellings that resolve to the same device, but it
is not worth worrying about working around that kind of abuse.
* src/conf/domain_conf.c (virDomainDefParseXML): Require unique
paths.
Enable block I/O throttle for per-disk in XML, as the first
per-disk IO tuning parameter.
Signed-off-by: Lei Li <lilei@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
This adds per-device weights to <blkiotune>. Note that the
cgroups implementation only supports weights per block device,
and not per-file within the device; hence this option must be
global to the domain definition rather than tied to individual
<devices>/<disk> entries:
<domain ...>
<blkiotune>
<device>
<path>/path/to/block</path>
<weight>1000</weight>
</device>
</blkiotune>
..
This patch also adds a parameter --device-weights to virsh command
blkiotune for setting/getting blkiotune.weight_device for any
hypervisor that supports it. All <device> entries under
<blkiotune> are concatenated into a single string attribute under
virDomain{Get,Set}BlkioParameters, named "device_weight".
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
virt-xml-validate fails when run on a domain XML file of type 'vbox'.
For failing test case, see https://bugzilla.redhat.com/show_bug.cgi?id=757097
This patch updates the XML schema to accept all valid hypervisor
types, as well as dropping hypervisor types that are not in use
by the current code base.
Signed-off-by: Eric Blake <eblake@redhat.com>
One of my latest patches 2e37bf42d2
copy serial console definition. On domain shutdown we save this
info into state XML. However, later on the daemon start we simply
drop this info and since we are not re-reading qemu log,
vm->def->consoles[0] does not get populated with copy. Therefore
we need to avoid dropping console definition if it is just alias
for serial console.
None of the callers cared if str was updated to point to the next
byte after the parsed cpuset; simplifying this results in quite
a few code simplifications. Additionally, virCPUDefParseXML was
strdup()'ing a malloc()'d string; avoiding a memory copy resulted
in less code.
* src/conf/domain_conf.h (virDomainCpuSetParse): Alter signature.
* src/conf/domain_conf.c (virDomainCpuSetParse): Don't modify str.
(virDomainVcpuPinDefParseXML, virDomainDefParseXML): Adjust
callers.
* src/conf/cpu_conf.c (virCPUDefParseXML): Likewise.
* src/xen/xend_internal.c (sexpr_to_xend_topology): Likewise.
* src/xen/xm_internal.c (xenXMDomainPinVcpu): Likewise.
* src/xenxs/xen_sxpr.c (xenParseSxpr): Likewise.
* src/xenxs/xen_xm.c (xenParseXM): Likewise.
Now, when we support multiple consoles per domain,
the vm->def->console[0] can still remain an alias
for vm->def->serial[0]; However, we need to copy
it's source definition as well otherwise we'll regress
on virDomainOpenConsole.
NWFilters can be provided name-value pairs using the following
XML notation:
<filterref filter='xyz'>
<parameter name='PORT' value='80'/>
<parameter name='VAL' value='abc'/>
</filterref>
The internal representation currently is so that a name is stored as a
string and the value as well. This patch now addresses the value part of it
and introduces a data structure for storing a value either as a simple
value or as an array for later support of lists.
This patch adjusts all code that was handling the values in hash tables
and makes it use the new data type.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
The virDomainNetGetActualBridgeName and virDomainNetGetActualDirectDev
methods both return strings that point to data in the virDomainDefPtr
struct, and should therefore not be freed. The return values should
thus be 'const char *' not 'char *'.
* src/conf/domain_conf.c, src/conf/domain_conf.h: Mark const
* src/network/bridge_driver.c: Update to use a const char *
In preparation for code re-organization, rename the Macvtap
management APIs to have the following patterns
virNetDevMacVLanXXXXX - macvlan/macvtap interface management
virNetDevVPortProfileXXXX - virtual port profile management
* src/util/macvtap.c, src/util/macvtap.h: Rename APIs
* src/conf/domain_conf.c, src/network/bridge_driver.c,
src/qemu/qemu_command.c, src/qemu/qemu_command.h,
src/qemu/qemu_driver.c, src/qemu/qemu_hotplug.c,
src/qemu/qemu_migration.c, src/qemu/qemu_process.c,
src/qemu/qemu_process.h: Update for renamed APIs
This patch adds XML definitions for guest NUMA specification and contains
routines to parse the same. The guest NUMA specification looks like this:
<cpu>
...
<topology sockets='2' cores='4' threads='2'/>
<numa>
<cell cpus='0-7' memory='512000'/>
<cell cpus='8-15' memory='512000'/>
</numa>
...
</cpu>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
For whatever reason, the kernel allows you to create a regular
file named /dev/sdc.12345; although this file will disappear the
next time devtmpfs is remounted. If you let libvirt generate
the name of the external snapshot for a disk image originally
using the block device /dev/sdc, then the domain will be rendered
unbootable once the qcow2 file is lost on the next devtmpfs
remount. In this case, the user should have used 'virsh
snapshot-create --xmlfile' or 'virsh snapshot-create-as --diskspec'
to specify the name for the qcow2 file in a sane location, rather
than relying on libvirt generating a name that is most likely to
be wrong. We can help avoid naive mistakes by enforcing that
the user provide the external name for any backing file that is
not a regular file.
* src/conf/domain_conf.c (virDomainSnapshotAlignDisks): Only
generate names if backing file exists as regular file.
Reported by MATSUDA Daiki.
The src/util/network.c file is a dumping ground for many different
APIs. Split it up into 5 pieces, along functional lines
- src/util/virnetdevbandwidth.c: virNetDevBandwidth type & helper APIs
- src/util/virnetdevvportprofile.c: virNetDevVPortProfile type & helper APIs
- src/util/virsocketaddr.c: virSocketAddr and APIs
- src/conf/netdev_bandwidth_conf.c: XML parsing / formatting
for virNetDevBandwidth
- src/conf/netdev_vport_profile_conf.c: XML parsing / formatting
for virNetDevVPortProfile
* src/util/network.c, src/util/network.h: Split into 5 pieces
* src/conf/netdev_bandwidth_conf.c, src/conf/netdev_bandwidth_conf.h,
src/conf/netdev_vport_profile_conf.c, src/conf/netdev_vport_profile_conf.h,
src/util/virnetdevbandwidth.c, src/util/virnetdevbandwidth.h,
src/util/virnetdevvportprofile.c, src/util/virnetdevvportprofile.h,
src/util/virsocketaddr.c, src/util/virsocketaddr.h: New pieces
* daemon/libvirtd.h, daemon/remote.c, src/conf/domain_conf.c,
src/conf/domain_conf.h, src/conf/network_conf.c,
src/conf/network_conf.h, src/conf/nwfilter_conf.h,
src/esx/esx_util.h, src/network/bridge_driver.c,
src/qemu/qemu_conf.c, src/rpc/virnetsocket.c,
src/rpc/virnetsocket.h, src/util/dnsmasq.h, src/util/interface.h,
src/util/iptables.h, src/util/macvtap.c, src/util/macvtap.h,
src/util/virnetdev.h, src/util/virnetdevtap.c,
tools/virsh.c: Update include files
The virtual port profile parsing/formatting APIs do not
correctly handle unknown profile type strings/numbers.
They behave as a no-op, instead of raising an error
* src/util/network.c, src/util/network.h: Fix error
handling of port profile APIs
* src/conf/domain_conf.c, src/conf/network_conf.c: Update
for API changes
Rename the virVirtualPortProfileParams struct to be
virNetDevVPortProfile, and rename the APIs to match
this prefix.
* src/util/network.c, src/util/network.h: Rename port profile
APIs
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/conf/network_conf.c, src/conf/network_conf.h,
src/network/bridge_driver.c, src/qemu/qemu_hotplug.c,
src/util/macvtap.c, src/util/macvtap.h: Update for
renamed APIs/structs
The socket address APIs in src/util/network.h either take the
form virSocketAddrXXX, virSocketXXX or virSocketXXXAddr.
Sanitize this so everything is virSocketAddrXXXX, and ensure
that the virSocketAddr parameter is always the first one.
* src/util/network.c, src/util/network.h: Santize socket
address API naming
* src/conf/domain_conf.c, src/conf/network_conf.c,
src/conf/nwfilter_conf.c, src/network/bridge_driver.c,
src/nwfilter/nwfilter_ebiptables_driver.c,
src/nwfilter/nwfilter_learnipaddr.c,
src/qemu/qemu_command.c, src/rpc/virnetsocket.c,
src/util/dnsmasq.c, src/util/iptables.c,
src/util/virnetdev.c, src/vbox/vbox_tmpl.c: Update for
API renaming
The default console type may vary based on the OS type. ie a Xen
paravirt guests wants a 'xen' console, while a fullvirt guests
wants a 'serial' console.
A plain integer default console type in the capabilities does
not suffice. Instead introduce a callback that is passed the
OS type.
* src/conf/capabilities.h: Use a callback for default console
type
* src/conf/domain_conf.c, src/conf/domain_conf.h: Use callback
for default console type. Add missing LXC/OpenVZ console types.
* src/esx/esx_driver.c, src/libxl/libxl_conf.c,
src/lxc/lxc_conf.c, src/openvz/openvz_conf.c,
src/phyp/phyp_driver.c, src/qemu/qemu_capabilities.c,
src/uml/uml_conf.c, src/vbox/vbox_tmpl.c,
src/vmware/vmware_conf.c, src/xen/xen_hypervisor.c,
src/xenapi/xenapi_driver.c: Set default console type callback
When no <target> element was set at all, the default console
target type was not being honoured
* src/conf/domain_conf.c: Set default target type for consoles
with no <target>
While Xen only has a single paravirt console, UML, and
QEMU both support multiple paravirt consoles. The LXC
driver can also be trivially made to support multiple
consoles. This patch extends the XML to allow multiple
<console> elements in the XML. It also makes the UML
and QEMU drivers support this config.
* src/conf/domain_conf.c, src/conf/domain_conf.h: Allow
multiple <console> devices
* src/lxc/lxc_driver.c, src/xen/xen_driver.c,
src/xenxs/xen_sxpr.c, src/xenxs/xen_xm.c: Update for
internal API changes
* src/security/security_selinux.c, src/security/virt-aa-helper.c:
Only label consoles that aren't a copy of the serial device
* src/qemu/qemu_command.c, src/qemu/qemu_driver.c,
src/qemu/qemu_process.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Support multiple console devices
* tests/qemuxml2xmltest.c, tests/qemuxml2argvtest.c: Extra
tests for multiple virtio consoles. Set QEMU_CAPS_CHARDEV
for all console /channel tests
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args
tests/qemuxml2argvdata/qemuxml2argv-console-virtio.args: Update
for correct chardev syntax
* tests/qemuxml2argvdata/qemuxml2argv-console-virtio-many.args,
tests/qemuxml2argvdata/qemuxml2argv-console-virtio-many.xml: New
test file
To support "managed" mode of host PCI device, we record the original
states (unbind_from_stub, remove_slot, and reprobe) so that could
reattach the device to host with original driver. But there is no XML
for theses attrs, and thus after daemon is restarted, we lose the
original states. It's easy to reproduce:
1) virsh start domain
2) virsh attach-device dom hostpci.xml (in 'managed' mode)
3) service libvirtd restart
4) virsh destroy domain
You will see the device won't be bound to the original driver
if there was one.
This patch is to solve the problem by introducing internal XML
(won't be dumped to user, only dumped to status XML). The XML is:
<origstates>
<unbind/>
<remove_slot/>
<reprobe/>
</origstates>
Which will be child node of <hostdev><source>...</souce></hostdev>.
(only for PCI device).
A new struct "virDomainHostdevOrigStates" is introduced for the XML,
and the according members are updated when preparing the PCI device.
And function "qemuUpdateActivePciHostdevs" is modified to honor
the original states. Use of qemuGetPciHostDeviceList is removed
in function "qemuUpdateActivePciHostdevs", and the "managed" value of
the device config is honored by the change. This fixes another problem
alongside:
qemuGetPciHostDeviceList set the device as "managed" force
regardless of whether the device is configured as "managed='yes'"
or not in XML, which is not right.
Add additional fields to let you specify the how to authenticate with a disk.
The secret to use may be referenced by a usage string or a UUID, i.e.:
<auth username='myuser'>
<secret type='ceph' usage='secretname'/>
</auth>
or
<auth username='myuser'>
<secret type='ceph' uuid='0a81f5b2-8403-7b23-c8d6-21ccc2f80d6f'/>
</auth>
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
Break some long lines, and use more efficient functions when possible,
such as relying on virBufferEscapeString to skip output on a NULL arg.
Ensure that output does not embed newlines, since auto-indent won't
work in those situations.
* src/conf/domain_conf.c (virDomainTimerDefFormat): Break output lines.
(virDomainDefFormatInternal, virDomainDiskDefFormat)
(virDomainActualNetDefFormat, virDomainNetDefFormat)
(virDomainHostdevDefFormat): Minor cleanups.
Fixing this involved some refactoring of common code out of
domain_conf and nwfilter_conf into nwfilter_params.
* src/conf/nwfilter_params.h (virNWFilterFormatParamAttributes):
Adjust signature.
* src/conf/nwfilter_params.c (_formatParameterAttrs)
(virNWFilterFormatParamAttributes): Adjust indentation handling,
and handle filterref here.
(formatterParam): Delete unused struct.
* src/conf/domain_conf.c (virDomainNetDefFormat): Adjust caller.
* src/conf/nwfilter_conf.c (virNWFilterIncludeDefFormat): Likewise.
This attribute says what to do with cdrom (or floppy) if
the source is missing. It accepts:
- mandatory - fail if missing for any reason (the default)
- requisite - fail if missing on boot up, drop if missing on
migrate/restore/revert
- optional - drop if missing at any start attempt.
However, this patch introduces only XML part of this new
functionality.
More simplifications possible due to auto-indent. Also,
<bandwidth> within <actual> was only using 6 instead of 8 spaces.
* src/util/network.h (virVirtualPortProfileFormat)
(virBandwidthDefFormat): Alter signature.
* src/util/network.c (virVirtualPortProfileFormat)
(virBandwidthDefFormat): Alter indentation.
(virBandwidthChildDefFormat): Tweak to make use easier.
* src/conf/network_conf.c (virPortGroupDefFormat)
(virNetworkDefFormat): Adjust callers.
* src/conf/domain_conf.c (virDomainNetDefFormat): Likewise.
(virDomainActualNetDefFormat): Likewise, and fix bandwidth
indentation.
Auto-indent makes life a bit easier; this patch also drops unused
arguments and replaces a misspelled flag name with two entry points
instead, so that callers don't have to worry about how much spacing
is present when embedding cpu elements.
* src/conf/cpu_conf.h (virCPUFormatFlags): Delete.
(virCPUDefFormat): Drop unused argument.
(virCPUDefFormatBuf): Alter signature.
(virCPUDefFormatBufFull): New prototype.
* src/conf/cpu_conf.c (virCPUDefFormatBuf): Split...
(virCPUDefFormatBufFull): ...into new function.
(virCPUDefFormat): Adjust caller.
* src/conf/domain_conf.c (virDomainDefFormatInternal): Likewise.
* src/conf/capabilities.c (virCapabilitiesFormatXML): Likewise.
* src/cpu/cpu.c (cpuBaselineXML): Likewise.
* tests/cputest.c (cpuTestCompareXML): Likewise.
The improvements to virBuffer, along with a paradigm shift to pass
the original buffer through rather than creating a second buffer,
allow us to shave off quite a few lines of code.
* src/util/sysinfo.h (virSysinfoFormat): Alter signature.
* src/util/sysinfo.c (virSysinfoFormat, virSysinfoBIOSFormat)
(virSysinfoSystemFormat, virSysinfoProcessorFormat)
(virSysinfoMemoryFormat): Change indentation parameter.
* src/conf/domain_conf.c (virDomainSysinfoDefFormat): Adjust
caller.
* src/qemu/qemu_driver.c (qemuGetSysinfo): Likewise.
Add a test for the simple parts of my indentation changes, and
fix the fallout.
* tests/domainsnapshotxml2xmltest.c: New test.
* tests/Makefile.am (domainsnapshotxml2xmltest_SOURCES): Build it.
* src/conf/domain_conf.c (virDomainSnapshotDefFormat): Avoid NULL
deref, match documented order.
* src/conf/domain_conf.h (virDomainSnapshotDefFormat): Add const.
* tests/domainsnapshotxml2xmlout/all_parameters.xml: Tweak output.
* tests/domainsnapshotxml2xmlout/disk_snapshot.xml: Likewise.
* tests/domainsnapshotxml2xmlout/full_domain.xml: Likewise.
* .gitignore: Exempt new binary.
<domainsnapshot> is the first public instance of <domain> being
used as a sub-element, although we have two other private uses
(runtime state, and migration cookie). Although indentation has
no effect on XML parsing, using it makes the output more consistent.
This uses virBuffer auto-indentation to obtain the effect, for all
but the portions of <domain> that are not generated a line at a
time into the same virBuffer. Further patches will clean up the
remaining problems.
* src/conf/domain_conf.h (virDomainDefFormatInternal): New prototype.
* src/conf/domain_conf.c (virDomainDefFormatInternal): Export.
(virDomainObjFormat, virDomainSnapshotDefFormat): Update callers.
* src/libvirt_private.syms (domain_conf.h): Add new export.
* src/qemu/qemu_migration.c (qemuMigrationCookieXMLFormat): Use
new function.
(qemuMigrationCookieXMLFormatStr): Update caller.
Detected by Coverity. Leak present since commit 874e65a; and
while commit d50bb45 tried to fix the issue, it missed a path.
* src/conf/domain_conf.c (virDomainDefParseBootXML): Always clean
up useserial.
With the recent refactoring of qemu snapshot relationships, it
is now trivial to filter on leaves.
* src/conf/domain_conf.c (virDomainSnapshotObjListCount)
(virDomainSnapshotObjListCopyNames): Handle new flag.
* src/qemu/qemu_driver.c (qemuDomainSnapshotListNames)
(qemuDomainSnapshotNum, qemuDomainSnapshotListChildrenNames)
(qemuDomainSnapshotNumChildren): Pass new flag through.
VirtFS allows the user to choose between path/handle based fs driver.
As of now, libvirt hardcoded path based driver only. This patch provides
a solution to allow user to choose between path/handle based fs driver.
Sample:
<filesystem type='mount'>
<driver type='handle'/>
<source dir='/folder/to/share1'/>
<target dir='mount_tag1'/>
</filesystem>
<filesystem type='mount'>
<driver type='path'/>
<source dir='/folder/to/share2'/>
<target dir='mount_tag2'/>
</filesystem>
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The previous optimizations lead to some follow-on cleanups.
* src/conf/domain_conf.c (virDomainSnapshotForEachChild)
(virDomainSnapshotForEachDescendant): Drop dead parameter.
(virDomainSnapshotActOnDescendant)
(virDomainSnapshotObjListNumFrom)
(virDomainSnapshotObjListGetNamesFrom): Update callers.
* src/qemu/qemu_driver.c (qemuDomainSnapshotNumChildren)
(qemuDomainSnapshotListChildrenNames, qemuDomainSnapshotDelete):
Likewise.
* src/conf/domain_conf.h: Update prototypes.
Among other improvements, virDomainSnapshotForEachDescendant is
changed from iterative O(n^2) to recursive O(n). A bit better
than the O(n^3) implementation in virsh snapshot-list!
* src/conf/domain_conf.c (virDomainSnapshotObjListNum)
(virDomainSnapshotObjListNumFrom)
(virDomainSnapshotObjeListGetNames, virDomainSnapshotForEachChild)
(virDomainSnapshotForEachDescendant): Optimize.
(virDomainSnapshotActOnDescendant): Tweak.
(virDomainSnapshotActOnChild, virDomainSnapshotMarkDescendant):
Delete, now that they are unused.
No one was using virDomainSnapshotHasChildren, but that was an
O(n) function. Exposing and tracking a bit more metadata for each
snapshot will allow the same query to be made with an O(1) query
of the member field. For single snapshot operations (create,
delete), callers can be trusted to maintain the metadata themselves,
but for reloading, we can't compute parents as we go since there
is no guarantee that parents were parsed before children, so we also
provide a function to refresh the relationships, and which can
be used to detect if the user has ignored our warnings and been
directly modifying files in /var/lib/libvirt/qemu/snapshot. This
patch only adds metadata; later patches will actually use it.
This layout intentionally hardcodes the size of each snapshot struct,
by tracking sibling pointers, rather than having to deal with the
headache of yet more memory management by directly sticking a
dynamically sized child[] on each parent.
* src/conf/domain_conf.h (_virDomainSnapshotObj)
(_virDomainSnapshotObjList): Add members.
(virDomainSnapshotUpdateRelations, virDomainSnapshotDropParent):
New prototypes.
(virDomainSnapshotHasChildren): Delete.
* src/conf/domain_conf.c (virDomainSnapshotSetRelations)
(virDomainSnapshotUpdateRelations, virDomainSnapshotDropParent):
New functions.
(virDomainSnapshotHasChildren): Drop unused function.
* src/libvirt_private.syms (domain_conf): Update exports.
Not too hard to wire up. The trickiest part is realizing that
listing children of a snapshot cannot use SNAPSHOT_LIST_ROOTS,
and that we overloaded that bit to also mean SNAPSHOT_LIST_DESCENDANTS;
we use that bit to decide which iteration to use, but don't want
the existing counting/listing functions to see that bit.
* src/conf/domain_conf.h (virDomainSnapshotObjListNumFrom)
(virDomainSnapshotObjListGetNamesFrom): New prototypes.
* src/conf/domain_conf.c (virDomainSnapshotObjListNumFrom)
(virDomainSnapshotObjListGetNamesFrom): New functions.
* src/libvirt_private.syms (domain_conf.h): Export them.
* src/qemu/qemu_driver.c (qemuDomainSnapshotNumChildren)
(qemuDomainSnapshotListChildrenNames): New functions.
Redefining disk-only snapshot xml should work even if the user
did not explicitly pass VIR_DOMAIN_SNAPSHOT_CREATE_DISK_ONLY;
the flag is only required for conditions where the <state>
subelement is not already present in parsing (that is, defining
a new snapshot).
Also, fix the error code of some user-visible errors (the remaining
VIR_ERR_INTERNAL_ERROR should not be user-visible, since parsing
of <active> is only done from internal code).
* src/conf/domain_conf.c (virDomainSnapshotDefParseString): Allow
disks during redefinition of disk snapshot.
Previously libvirt's disk device XML only had a single attribute,
error_policy, to control both read and write error policy, but qemu
has separate options for controlling read and write. In one case
(enospc) a policy is allowed for write errors but not read errors.
This patch adds a separate attribute that sets only the read error
policy. If just error_policy is set, it will apply to both read and
write error policy (previous behavior), but if the new rerror_policy
attribute is set, it will override error_policy for read errors only.
Possible values for rerror_policy are "stop", "report", and "ignore"
("report" is the qemu-controlled default for rerror_policy when
error_policy isn't specified).
For consistency, the value "report" has been added to the possible
values for error_policy as well.
commit 12062ab set rerror=ignore when error_policy="enospace" was
selected (since the rerror option in qemu doesn't accept "enospc", as
the werror option does).
After that patch was already pushed, Paolo Bonzini noticed it and
commented that leaving rerror at the default ("report") would be a
better choice. This patch corrects the problem - if error_policy =
"enospace" is given, rerror is left off the qemu commandline,
effectively setting it to "report". For other values, rerror is still
set to match werror.
Additionally, the parsing of error_policy was changed to no longer
erroneously allow "default" as a choice - as with most other
attributes, if you want the default setting, just don't specify an
error_policy.
Finally, two ommissions in the first patch were corrected - a
long-dormant qemuxml2argv test for enospace was enabled, and fixed to
pass, and the argv2xml parser in qemu_command.c was updated to
recognize the different spelling on the qemu commandline.
When booting a virtual machine with a kernel/initrd it is possible
to pass command line arguments using the <cmdline>...args...</cmdline>
element in the guest XML. These appear to the kernel / init process
in /proc/cmdline.
When booting a container we do not have a custom /proc/cmdline,
but we can easily set an environment variable for it. Ideally
we could pass individual arguments to the init process as a
regular set of 'char *argv[]' parameters, but that would involve
libvirt parsing the <cmdline> XML text. This can easily be added
later, even if we add the env variable now
* docs/drvlxc.html.in: Document env variables passed to LXC
* src/conf/domain_conf.c: Add <cmdline> to be parsed for
guests of type='exe'
* src/lxc/lxc_container.c: Set LIBVIRT_LXC_CMDLINE env var
This patch is a fix for:
https://bugzilla.redhat.com/show_bug.cgi?id=743176
which was discovered by Dan Berrange while making bandwidth
configuration work for LXC guests.
Background: Although virtportprofile data from a network portgroup is
only applicable for direct mode interfaces, the code that copies
bandwidth data from the portgroup was also only being executed in the
case of direct mode interfaces. The result was that interfaces using
traditional virtual networks (forward mode='nat|route|none'), and
those using a host bridge for forwarding, would not pick up bandwidth
data from a portgroup defined in the network.
This patch moves that code outside the conditional, so that bandwidth
information is *alway* copied from the appropriate portgroup (unless
the <interface> definition itself already has bandwidth information,
which would take precedence over what's in the portgroup anyway).
When support for was added for PCI multifunction cards (in commit
9f8baf, first included in libvirt 0.9.3), it was done by always
turning on the multifunction bit for all PCI devices. Since that time
it has been realized that this is not an ideal solution, and that the
multifunction bit must be selectively turned on. For example, see
https://bugzilla.redhat.com/show_bug.cgi?id=728174
and the discussion before and after
https://www.redhat.com/archives/libvir-list/2011-September/msg01036.html
This patch modifies multifunction support so that the multifunction=on
option is only added to the qemu commandline for a device if its PCI
<address> definition has the attribute "multifunction='on'", e.g.:
<address type='pci' domain='0x0000' bus='0x00'
slot='0x04' function='0x0' multifunction='on'/>
In practice, the multifunction bit should only be turned on if
function='0' AND other functions will be used in the same slot - it
usually isn't needed for functions 1-7 (although there are apparently
some exceptions, e.g. the Intel X53 according to the QEMU source
code), and should never be set if only function 0 will be used in the
slot. The test cases have been changed accordingly to illustrate.
With this patch in place, if a user attempts to assign multiple
functions in a slot without setting the multifunction bit for function
0, libvirt will issue an error when the domain is defined, and the
define operation will fail. In the future, we may decide to detect
this situation and automatically add multifunction=on to avoid the
error; even then it will still be useful to have a manual method of
turning on multifunction since, as stated above, there are some
devices that excpect it to be turned on for all functions in a slot.
A side effect of this patch is that attempts to use the same PCI
address for two different devices will now log an error (previously
this would cause the domain define operation to fail, but there would
be no log message generated). Because the function doing this log was
almost completely rewritten, I didn't think it worthwhile to make a
separate patch for that fix (the entire patch would immediately be
obsoleted).
This patch was made in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=738095
In short, qemu's default for the rombar setting (which makes the
firmware ROM of a PCI device visible/not on the guest) was previously
0 (not visible), but they recently changed the default to 1
(visible). Unfortunately, there are some PCI devices that fail in the
guest when rombar is 1, so the setting must be exposed in libvirt to
prevent a regression in behavior (it will still require explicitly
setting <rom bar='off'/> in the guest XML).
rombar is forced on/off by adding:
<rom bar='on|off'/>
inside a <hostdev> element that defines a PCI device. It is currently
ignored for all other types of devices.
At the moment there is no clean method to determine whether or not the
rombar option is supported by QEMU - this patch uses the advice of a
QEMU developer to assume support for qemu-0.12+. There is currently a
patch in the works to put this information in the output of "qemu-kvm
-device pci-assign,?", but of course if we switch to keying off that,
we would lose support for setting rombar on all the versions of qemu
between 0.12 and whatever version gets that patch.
QEMU 0.13 introduced cache=unsafe for -drive, this patch exposes
it in the libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_UNSAFE),
as even if $prefix_CACHE_V2 is set, we can't know if unsafe
is supported.
* Improved the reliability of qemu cache type detection.
This patch is mostly code motion - moving some functions out
of qemu_driver and into qemu_domain so they can be reused by
multiple qemu_* files (since qemu_driver.h must not grow).
It also adds a new helper function, qemuDomainRemoveInactive,
which will be used in the next patch.
* src/qemu/qemu_domain.h (qemuFindQemuImgBinary)
(qemuDomainSnapshotWriteMetadata, qemuDomainSnapshotForEachQcow2)
(qemuDomainSnapshotDiscard, qemuDomainSnapshotDiscardAll)
(qemuDomainRemoveInactive): New prototypes.
(struct qemu_snap_remove): New struct.
* src/qemu/qemu_domain.c (qemuDomainRemoveInactive)
(qemuDomainSnapshotDiscardAllMetadata): New functions.
(qemuFindQemuImgBinary, qemuDomainSnapshotWriteMetadata)
(qemuDomainSnapshotForEachQcow2, qemuDomainSnapshotDiscard)
(qemuDomainSnapshotDiscardAll): Move here...
* src/qemu/qemu_driver.c (qemuFindQemuImgBinary)
(qemuDomainSnapshotWriteMetadata, qemuDomainSnapshotForEachQcow2)
(qemuDomainSnapshotDiscard, qemuDomainSnapshotDiscardAll): ...from
here.
(qemuDomainUndefineFlags): Update caller.
* src/conf/domain_conf.c (virDomainRemoveInactive): Doc fixes.
Libvirt loads the domain conf from status XML if it's running when
starting up. The problem is there is no record of the original conf.
(dom->newDef is NULL here).
So libvirt won't be able to restore the domain conf to original one
when destroying/shutdown. E.g.
1) attach a device without "--persistent"
2) restart libvirtd
3) destroy domain
4) start domain
One will see the the disk still exists.
This patch is to fix the peoblem by assigning persistent domain conf
to dom->newDef if it's NULL and the domain is running.
Qemu sends STOP event as part of the shutdown process. Detect such STOP
event and consider shutdown to be reason of emitting such event. That's
the best we can do until qemu provides us the reason directly in STOP
event. This allows us to report shutdown reason for paused state so that
apps can detect domains that failed to finish the shutdown process
(e.g., because qemu is buggy and doesn't exit on SIGTERM or it is
blocked in flushing disk buffers).
* conf/domain_conf.c: allocate memory to def->redirdevs in
virDomainDefParseXML such as VIR_ALLOC_N(def->redirdevs, n),
however, virDomainDefFree(def) hasn't released these memory.
* Detected in valgrind run:
==19820== 209 (16 direct, 193 indirect) bytes in 1 blocks are definitely lost in loss record 25 of 26
==19820== at 0x4A04A28: calloc (vg_replace_malloc.c:467)
==19820== by 0x4A13AF: virAllocN (memory.c:129)
==19820== by 0x4D4A0E: virDomainDefParseXML (domain_conf.c:7258)
==19820== by 0x4D4C93: virDomainDefParseNode (domain_conf.c:7512)
==19820== by 0x4D562F: virDomainDefParse (domain_conf.c:7465)
==19820== by 0x415863: testCompareXMLToXMLFiles (qemuxml2xmltest.c:35)
==19820== by 0x415982: testCompareXMLToXMLHelper (qemuxml2xmltest.c:80)
==19820== by 0x416D31: virtTestRun (testutils.c:140)
==19820== by 0x415604: mymain (qemuxml2xmltest.c:192)
==19820== by 0x416437: virtTestMain (testutils.c:689)
==19820== by 0x3CA7A1ECDC: (below main) (in /lib64/libc-2.12.so)
==19820==
==19820== LEAK SUMMARY:
==19820== definitely lost: 16 bytes in 1 blocks
==19820== indirectly lost: 193 bytes in 5 blocks
==19820== possibly lost: 0 bytes in 0 blocks
==19820== still reachable: 1,054 bytes in 21 blocks
* How to reproduce?
% valgrind -v --leak-check=full ./tests/qemuxml2xmltest
Signed-off-by: Alex Jia <ajia@redhat.com>
Commit 973fcd8f introduced the ability for qemu to reject snapshot
reversion on an ABI incompatibility; but the very example that was
first proposed on-list[1] as a demonstration of an ABI incompatibility,
namely that of changing the max memory allocation, was not being
checked for, resulting in a cryptic failure when running with larger
max mem than what the snapshot was created with:
error: operation failed: Error -22 while loading VM state
This commit merely protects the three variables within mem that are
referenced by qemu_command.c, rather than all 7 (the other 4 variables
affect cgroup handling, but as far as I can tell, have no visible effect
to the qemu guest). This also affects migration and save file handling,
which are other places where we perform ABI compatibility checks.
[1] https://www.redhat.com/archives/libvir-list/2010-December/msg00331.html
* src/conf/domain_conf.c (virDomainDefCheckABIStability): Add
memory sizing checks.
Commit 498d783 cleans up some of virtual file names for parsing strings
in memory. This patch cleans up (hopefuly) the rest forgotten by the
first patch.
This patch also changes all of the previously modified "filenames" to
valid URI's replacing spaces for underscores.
Changes to v1:
- Replace all spaces for underscores, so that the strings form valid
URI's
- Replace spaces in places changed by commit 498d783
While parsing XML strings from memory, the previous convention in
libvirt was to set the virtual file name to "domain.xml" or something
similar. This could potentialy trick the user into looking for a file
named domain.xml on the disk in an attempt to fix the error.
This patch changes these filenames to something that can't be as easily
confused for a valid filename.
Examples of error messages:
---------------------------
Error while loading file from disk:
15:07:59.015: 527: error : catchXMLError:709 : /path/to/domain.xml:1: StartTag: invalid element name
<domain type='kvm'><
--------------------^
Error while parsing definition in memory:
15:08:43.581: 525: error : catchXMLError:709 : (domain definition):2: error parsing attribute name
<name>vm1</name>
--^
Regression introduced in commit d6f6b2d194. Running
'virsh snapshot-create dom' would mistakenly report that
disks can only be specified for disk snapshots.
* src/conf/domain_conf.c (virDomainSnapshotDefParseString): Only
give error about no disk support when <disk> was found.
A new element is introduced to XML that allows to control
state of virtual network interfaces in hypervisors.
Live modification of the link state allows networking tools
propagate topology changes to guest OS or testing of
scenarios in complex (virtual) networks.
This patch adds elements to XML grammars and parsing and generating
code.
It is important to be able to attach USB redirected devices to a
particular controller (one that supports USB2 for instance).
Without this patch, only the default bus was used.
<redirdev bus='usb' type='spicevmc'>
<address type='usb' bus='0' port='4'/>
</redirdev>
I got confused when 'virsh domblkinfo dom disk' required the
path to a disk (which can be ambiguous, since a single file
can back multiple disks), rather than the unambiguous target
device name that I was using in disk snapshots. So, in true
developer fashion, I went for the best of both worlds - all
interfaces that operate on a disk (aka block) now accept
either the target name or the unambiguous path to the backing
file used by the disk.
* src/conf/domain_conf.h (virDomainDiskIndexByName): Add
parameter.
(virDomainDiskPathByName): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainDiskIndexByName): Also allow
searching by path, and decide whether ambiguity is okay.
(virDomainDiskPathByName): New function.
(virDomainDiskRemoveByName, virDomainSnapshotAlignDisks): Update
callers.
* src/qemu/qemu_driver.c (qemudDomainBlockPeek)
(qemuDomainAttachDeviceConfig, qemuDomainUpdateDeviceConfig)
(qemuDomainGetBlockInfo, qemuDiskPathToAlias): Likewise.
* src/qemu/qemu_process.c (qemuProcessFindDomainDiskByPath):
Likewise.
* src/libxl/libxl_driver.c (libxlDomainAttachDeviceDiskLive)
(libxlDomainDetachDeviceDiskLive, libxlDomainAttachDeviceConfig)
(libxlDomainUpdateDeviceConfig): Likewise.
* src/uml/uml_driver.c (umlDomainBlockPeek): Likewise.
* src/xen/xend_internal.c (xenDaemonDomainBlockPeek): Likewise.
* docs/formatsnapshot.html.in: Update documentation.
* tools/virsh.pod (domblkstat, domblkinfo): Likewise.
* docs/schemas/domaincommon.rng (diskTarget): Tighten pattern on
disk targets.
* docs/schemas/domainsnapshot.rng (disksnapshot): Update to match.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: Update test.
Adds an optional element to <domainsnapshot>, which will be used
to give user control over external snapshot filenames on input,
and specify generated filenames on output.
For now, no driver accepts this element; that will come later.
<domainsnapshot>
...
<disks>
<disk name='vda' snapshot='no'/>
<disk name='vdb' snapshot='internal'/>
<disk name='vdc' snapshot='external'>
<driver type='qcow2'/>
<source file='/path/to/new'/>
</disk>
</disks>
<domain>
...
<devices>
<disk ...>
<driver name='qemu' type='raw'/>
<target dev='vdc'/>
<source file='/path/to/old'/>
</disk>
</devices>
</domain>
</domainsnapshot>
* src/conf/domain_conf.h (_virDomainSnapshotDiskDef): New type.
(_virDomainSnapshotDef): Add new elements.
(virDomainSnapshotAlignDisks): New prototype.
* src/conf/domain_conf.c (virDomainSnapshotDiskDefClear)
(virDomainSnapshotDiskDefParseXML, disksorter)
(virDomainSnapshotAlignDisks): New functions.
(virDomainSnapshotDefParseString): Parse new fields.
(virDomainSnapshotDefFree): Clean them up.
(virDomainSnapshotDefFormat): Output them.
* src/libvirt_private.syms (domain_conf.h): Export new function.
* docs/schemas/domainsnapshot.rng (domainsnapshot, disksnapshot):
Add more xml.
* docs/formatsnapshot.html.in: Document it.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: New test.
* tests/domainsnapshotxml2xmlout/disk_snapshot.xml: Update.
In order to distinguish disk snapshots from system checkpoints, a
new state value that is only valid for snapshots is helpful.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_LAST): New placeholder.
* src/conf/domain_conf.h (virDomainSnapshotState): New enum mapping.
(VIR_DOMAIN_DISK_SNAPSHOT): New internal enum value.
* src/conf/domain_conf.c (virDomainState): Use placeholder.
(virDomainSnapshotState): Extend mapping by one for use in snapshot.
(virDomainSnapshotDefParseString, virDomainSnapshotDefFormat):
Handle new state.
(virDomainObjSetState, virDomainStateReasonToString)
(virDomainStateReasonFromString): Avoid compiler warnings.
* tools/virsh.c (vshDomainState, vshDomainStateReasonToString):
Likewise.
* src/libvirt_private.syms (domain_conf.h): Export new functions.
* docs/schemas/domainsnapshot.rng: Tighten state definition.
* docs/formatsnapshot.html.in: Document it.
* tests/domainsnapshotxml2xmlout/disk_snapshot.xml: New test.
As discussed here:
https://www.redhat.com/archives/libvir-list/2011-August/msg00361.htmlhttps://www.redhat.com/archives/libvir-list/2011-August/msg00552.html
Adds snapshot attribute and transient sub-element:
<devices>
<disk type=... snapshot='no|internal|external'>
...
<transient/>
</disk>
</devices>
* docs/schemas/domaincommon.rng (snapshot): New define.
(disk): Add snapshot and persistent attributes.
* docs/formatdomain.html.in: Document them.
* src/conf/domain_conf.h (virDomainDiskSnapshot): New enum.
(_virDomainDiskDef): New fields.
* tests/qemuxml2argvdata/qemuxml2argv-disk-transient.xml: New
test of rng, no args counterpart until qemu support is complete.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.args: New
file, snapshot attribute does not affect args.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.xml: Likewise.
* tests/qemuxml2argvtest.c (mymain): Run new test.
Commit 69278878 fixed one direction of arbitrarily-named snapshots,
but not the round trip path. While auditing domain_conf, I found
a couple other instances that weren't escaping arbitrary strings.
* src/conf/domain_conf.c (virDomainFSDefFormat)
(virDomainGraphicsListenDefFormat, virDomainSnapshotDefFormat):
Escape arbitrary strings.
Just like VM saved state images (virsh save), snapshots MUST
track the inactive domain xml to detect any ABI incompatibilities.
The indentation is not perfect, but functionality comes before form.
Later patches will actually supply a full domain; for now, this
wires up the storage to support one, but doesn't ever generate one
in dumpxml output.
Happily, libvirt.c was already rejecting use of VIR_DOMAIN_XML_SECURE
from read-only connections, even though before this patch, there was
no information to be secured by the use of that flag.
And while we're at it, mark the libvirt snapshot metadata files
as internal-use only.
* src/libvirt.c (virDomainSnapshotGetXMLDesc): Document flag.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Add member.
(virDomainSnapshotDefParseString, virDomainSnapshotDefFormat):
Update signature.
* src/conf/domain_conf.c (virDomainSnapshotDefFree): Clean up.
(virDomainSnapshotDefParseString): Optionally parse domain.
(virDomainSnapshotDefFormat): Output full domain.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML)
(esxDomainSnapshotGetXMLDesc): Update callers.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML)
(vboxDomainSnapshotGetXMLDesc): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML)
(qemuDomainSnapshotLoad, qemuDomainSnapshotGetXMLDesc)
(qemuDomainSnapshotWriteMetadata): Likewise.
* docs/formatsnapshot.html.in: Rework doc example.
Based on a patch by Philipp Hahn.
Minor semantic change - allow domain xml to be generated in place
within a larger buffer, rather than having to go through a
temporary string.
* src/conf/domain_conf.c (virDomainDefFormatInternal): Add
parameter.
(virDomainDefFormat, virDomainObjFormat): Update callers.
Redefining a qemu snapshot requires a bit of a tweak to the common
snapshot parsing code, but the end result is quite nice.
Be careful that redefinitions do not introduce circular parent
chains. Also, we don't want to allow conversion between online
and offline existing snapshots. We could probably do some more
validation for snapshots that don't already exist to make sure
they are even feasible, by parsing qemu-img output, but that
can come later.
* src/conf/domain_conf.h (virDomainSnapshotParseFlags): New
internal flags.
* src/conf/domain_conf.c (virDomainSnapshotDefParseString): Alter
signature to take internal flags.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML): Update caller.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Support
new public flags.
Similar to the last patch in isolating the filtering from the
client actions, so that clients don't have to reinvent the
filtering.
* src/conf/domain_conf.h (virDomainSnapshotForEachChild): New
prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainSnapshotActOnChild)
(virDomainSnapshotForEachChild): New functions.
(virDomainSnapshotCountChildren): Delete.
(virDomainSnapshotHasChildren): Simplify.
* src/qemu/qemu_driver.c (qemuDomainSnapshotReparentChildren)
(qemuDomainSnapshotDelete): Likewise.
This one's nasty. Ever since we fixed virHashForEach to prevent
nested hash iterations for safety reasons (commit fba550f6),
virDomainSnapshotDelete with VIR_DOMAIN_SNAPSHOT_DELETE_CHILDREN
has been broken for qemu: it deletes children, while leaving
grandchildren intact but pointing to a no-longer-present parent.
But even before then, the code would often appear to succeed to
clean up grandchildren, but risked memory corruption if you have
a large and deep hierarchy of snapshots.
For acting on just children, a single virHashForEach is sufficient.
But for acting on an entire subtree, it requires iteration; and
since we declared recursion as invalid, we have to switch to a
while loop. Doing this correctly requires quite a bit of overhaul,
so I added a new helper function to isolate the algorithm from the
actions, so that callers do not have to reinvent the iteration.
Note that this _still_ does not handle CHILDREN correctly if one
of the children is the current snapshot; that will be next.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Add mark.
(virDomainSnapshotForEachDescendant): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainSnapshotMarkDescendant)
(virDomainSnapshotActOnDescendant)
(virDomainSnapshotForEachDescendant): New functions.
* src/qemu/qemu_driver.c (qemuDomainSnapshotDiscardChildren):
Replace...
(qemuDomainSnapshotDiscardDescenent): ...with callback that
doesn't nest hash traversal.
(qemuDomainSnapshotDelete): Use new function.
Each snapshot lookup was iterating over the entire hash table, O(n),
instead of honing in directly on the hash key, amortized O(1).
Besides, fixing this means that virDomainSnapshotFindByName can now
be used inside another virHashForeach iteration (without this patch,
attempts to lookup a snapshot by name during a hash iteration will
fail due to nested iteration).
* src/conf/domain_conf.c (virDomainSnapshotFindByName): Simplify.
(virDomainSnapshotObjListSearchName): Delete unused function.
So that devices can be attached to hubs. Example, to attach to first
port of a usb-hub on port 1.
<hub type='usb'>
<address type='usb' bus='0' port='1'/>
</hub>
<input type='mouse' type='usb'>
<address type='usb' bus='0' port='1.1'/>
</hub>
also add a test entry
Newer QEMU introduced cache=directsync for -drive, this patchset
is to expose it in libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_DIRECTSYNC),
As even $prefix_CACHE_V2 is set, we can't known if directsync
is supported.
Audit all changes to the qemu vm->current_snapshot, and make them
update the saved xml file for both the previous and the new
snapshot, so that there is always at most one snapshot with
<active>1</active> in the xml, and that snapshot is used as the
current snapshot even across libvirtd restarts.
This patch does not fix the case of virDomainSnapshotDelete(,CHILDREN)
where one of the children is the current snapshot; that will be later.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Alter member
type and name.
* src/conf/domain_conf.c (virDomainSnapshotDefParseString)
(virDomainSnapshotDefFormat): Update clients.
* docs/schemas/domainsnapshot.rng: Tighten rng.
* src/qemu/qemu_driver.c (qemuDomainSnapshotLoad): Reload current
snapshot.
(qemuDomainSnapshotCreateXML, qemuDomainRevertToSnapshot)
(qemuDomainSnapshotDiscard): Track current snapshot.
In some versions of qemu, both virtio-blk-pci and virtio-net-pci
devices can have an event_idx setting that determines some details of
event processing. When it is enabled, it "reduces the number of
interrupts and exits for the guest". qemu will automatically enable
this feature when it is available, but there may be cases where this
new feature could actually make performance worse (NB: no such case
has been found so far).
As a safety switch in case such a situation is encountered in the
field, this patch adds a new attribute "event_idx" to the <driver>
element of both disk and interface devices. event_idx can be set to
"on" (to force event_idx on in case qemu has it disabled by default)
or "off" (for force event_idx off). In the case that event_idx support
isn't present in qemu, the attribute is ignored (this on the advice of
the qemu developer).
docs/formatdomain.html.in: document the new flag (marking it as
"don't mess with this!"
docs/schemas/domain.rng: add event_idx in appropriate places
src/conf/domain_conf.[ch]: add event_idx to parser and formatter
src/libvirt_private.syms: export
virDomainVirtioEventIdx(From|To)String
src/qemu/qemu_capabilities.[ch]: detect and report event_idx in
disk/net
src/qemu/qemu_command.c: add event_idx parameter to qemu commandline
when appropriate.
tests/qemuxml2argvdata/qemuxml2argv-event_idx.args,
tests/qemuxml2argvdata/qemuxml2argv-event_idx.xml,
tests/qemuxml2argvtest.c,
tests/qemuxml2xmltest.c: test cases for event_idx.
Originally noticed by comparing the xml generated by virDomainSave
with the xml produced by reparsing and redumping that xml, but I
also did an audit of every last use of VIR_DOMAIN_XML_INACTIVE in
domain_conf.c to ensure that no other discrepancies exist.
* src/conf/domain_conf.c (virDomainDeviceInfoIsSet): Add
parameter, and update all callers. Make static.
(virDomainNetDefFormat): Skip generated ifname.
(virDomainDefFormatInternal): Skip default <seclabel>.
(virDomainChrSourceDefParseXML): Skip generated pty path, and add
parameter. Update callers.
* src/conf/domain_conf.h (virDomainDeviceInfoIsSet): Delete.
* src/libvirt_private.syms (domain_conf.h): Update.
Using a macro ensures that all the code is looking for the same
prefix.
* src/conf/domain_conf.h (VIR_NET_GENERATED_PREFIX): New macro.
* src/conf/domain_conf.c (virDomainNetDefParseXML): Use it.
* src/uml/uml_conf.c (umlConnectTapDevice): Likewise.
* src/qemu/qemu_command.c (qemuNetworkIfaceConnect): Likewise.
Suggested by Laine Stump.
Once it's plugged in, the <listen> element will be an optional
replacement for the "listen" attribute that graphics elements already
have. If the <listen> element is type='address', it will have an
attribute called 'address' which will contain an IP address or dns
name that the guest's display server should listen on. If, however,
type='network', the <listen> element should have an attribute called
'network' that will be set to the name of a network configuration to
get the IP address from.
* docs/schemas/domain.rng: updated to allow the <listen> element
* docs/formatdomain.html.in: document the <listen> element and its
attributes.
* src/conf/domain_conf.[hc]:
1) The domain parser, formatter, and data structure are modified to
support 0 or more <listen> subelements to each <graphics>
element. The old style "legacy" listen attribute is also still
accepted, and will be stored internally just as if it were a
separate <listen> element. On output (i.e. format), the address
attribute of the first <listen> element of type 'address' will be
duplicated in the legacy "listen" attribute of the <graphic>
element.
2) The "listenAddr" attribute has been removed from the unions in
virDomainGRaphicsDef for graphics types vnc, rdp, and spice.
This attribute is now in the <listen> subelement (aka
virDomainGraphicsListenDef)
3) Helper functions were written to provide simple access
(both Get and Set) to the listen elements and their attributes.
* src/libvirt_private.syms: export the listen helper functions
* src/qemu/qemu_command.c, src/qemu/qemu_hotplug.c,
src/qemu/qemu_migration.c, src/vbox/vbox_tmpl.c,
src/vmx/vmx.c, src/xenxs/xen_sxpr.c, src/xenxs/xen_xm.c
Modify all these files to use the listen helper functions rather
than directly referencing the (now missing) listenAddr
attribute. There can be multiple <listen> elements to a single
<graphics>, but the drivers all currently only support one, so all
replacements of direct access with a helper function indicate index
"0".
* tests/* - only 3 of these are new files added explicitly to test the
new <listen> element. All the others have been modified to reflect
the fact that any legacy "listen" attributes passed in to the domain
parse will be saved in a <listen> element (i.e. one of the
virDomainGraphicsListenDefs), and during the domain format function,
both the <listen> element as well as the legacy attributes will be
output.
Every DomainNetDef has a bandwidth, as does every portgroup.
Whenever a DomainNetDef of type NETWORK is about to be used, a call is
made to networkAllocateActualDevice(). This function chooses the "best"
bandwidth object and places it in the DomainActualNetDef.
From that point on, whenever some code needs to use the bandwidth data
for the interface, it's retrieved with virDomainNetGetActualBandwidth(),
which will always return the "best" info as determined in the
previous step.
These functions parse given XML node and return pointer to the
output. Unknown elements are silently ignored. Attributes must
be integer and must fit in unsigned long long.
Free function frees elements of virBandwidth structure.
the domain XML <interface> element is updated in the following ways:
1) <virtualportprofile> can be specified when source type='network'
(previously it was only valid for source type='direct')
2) A new attribute "portgroup" has been added to the <source>
element. When source type='network' (the only time portgroup is
recognized), extra configuration information will be taken from the
<portgroup> element of the given name in the network definition.
3) Each virDomainNetDef now also potentially has a
virDomainActualNetDef which is a private object (never
exported/imported via the public API, and not defined in the RNG) that
is used to maintain information about the physical device that was
actually used for a NetDef of type VIR_DOMAIN_NET_TYPE_NETWORK.
The virDomainActualNetDef will only be parsed/formatted if the
parse/format function is called with the
VIR_DOMAIN_XML_INTERNAL_ACTUAL_NET flag set (which is only needed when
saving/loading a running domain's state info to the stateDir).
The virtPortProfile in the domain interface struct is now a separately
allocated object *pointed to by* (rather than contained in) the main
virDomainNetDef object. This is done to make it easier to figure out
when a virtualPortProfile has/hasn't been specified in a particular
config.
virtPortProfiles are currently only used in the domain XML, but will
soon also be used in the network XML. To prepare for that change, this
patch moves the structure definition into util/network.h and the parse
and format functions into util/network.c (I decided that this was a
better choice than macvtap.h/c for something that needed to always be
available on all platforms).
