In 361c8dc17 and 662140fa68 I've implemented hot-(un)plug of
watchdog devices. Document this change.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1447169
Since domain can have at most one watchdog it simplifies things a
bit. However, since we must be able to set the watchdog action as
well, new monitor command needs to be used.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Currently we don't do it. Therefore we accept senseless
combinations of models and buses they are attached to.
Moreover, diag288 watchdog is exclusive to s390(x).
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1475250
It's possible to define and start a pool with a '.' in the
name; however, when trying to add a volume to a domain using
the storage pool source with a '.' in the storage pool name,
the domain RNG validation fails because RNG uses 'genericName'
which does not allow a '.' in the name.
Domain XML def parsing has a virXMLValidateAgainstSchema which
generates the error. The Storage Pool XML def parsing has no
call to virXMLValidateAgainstSchema. The only Storage Pool name
validation occurs in virStoragePoolDefParseXML to ensure the
name doesn't have a '/' in it and in storagePoolDefineXML to
call virXMLCheckIllegalChars using the same parameter "\n" as
qemuDomainDefineXMLFlags would check after the RNG check
could be succesful.
In order to resolve this, create a poolName definition in
storagecommon.rng that will mimic the domain name regex that
disallows a newline character, but add the "/" in the exclude
list. Then modify the pool and volume source name definitions
to key off that poolName.
Unindent the static XML block and move around the autoindent calls so
that further additions don't have to add more of them.
Also rename the string holding the static XML section.
For VMs with persistent config the config may change upon successful
completion of a job. Save it always if a persistent VM finishes a
blockjob. This will simplify further additions.
The status XML would be saved only for the copy job (in case of success)
or on failure even for other jobs. As the status contains the backing
chain data, which change after success we should always save it on
block job completion.
In cea3715b2e and d86fd2402e I've fixed domifstat and QoS
that was reversed for some types of interfaces. Document this
in the news file.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Checking of disk presence accesses storage on the host so it should be
done from the host setup function. Move the code to new function called
qemuProcessPrepareHostStorage and remove qemuDomainCheckDiskPresence.
Introduce a new function to prepare domain disks which will also do the
volume source to actual disk source translation.
The 'pretend' condition is not transferred to the new location since it
does not help in writing tests and also no tests abuse it.
Pass flags to the function rather than just whether we have incoming
migration. This also enforces correct startup policy for USB devices
when reverting from a snapshot.
qemuMigrationPrepareAny called multiple of the functions starting the
qemu process for incoming migration by adding the flags explicitly.
Extract them to a variable so that they can be easily used for other
calls or changed in the future.
Interestingly enough, we don't document the point of view of the
interface statistics. Therefore it's unknown to users if for
instance rx_packets is the number of packets received by domain or
received by host (from domain). Document this explicitly.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Similarly to previous patch, for some types of interface domain
and host are on the same side of RX/TX barrier. In that case, we
need to set up the QoS differently. Well, swapped.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1497410
The comment in virNetDevTapInterfaceStats() implementation for
Linux states that packets transmitted by domain are received by
the host and vice versa. Well, this is true but not for all types
of interfaces. For instance, for macvtaps when TAP device is
hooked right onto a physical device any packet that domain sends
looks also like a packet sent to the host. Therefore, we should
allow caller to chose if the stats returned should be straight
copy or swapped.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Small wrapper to lookup interface in domain definition by its
name.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Users might have configured interface so that it's type of
network, but the corresponding network plugs interfaces into an
OVS bridge. Therefore, we have to check for the actual type of
the interface instead of the configured one.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
This code compiles only on Linux. Therefore the condition we
check is always true.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
clang doesn't like mode_t type as an argument to va_arg():
error: second argument to 'va_arg' is of promotable type 'mode_t' (aka
'unsigned short'); this va_arg has undefined behavior because arguments
will be promoted to 'int'
mode = va_arg(ap, mode_t);
^~~~~~
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
qemu 2.7.0 introduces multiqueue virtio-blk(commit 2f27059).
This patch introduces a new attribute "queues". An example of
the XML:
<disk type='file' device='disk'>
<driver name='qemu' type='qcow2' queues='4'/>
The corresponding QEMU command line:
-device virtio-blk-pci,scsi=off,num-queues=4,id=virtio-disk0
Signed-off-by: Lin Ma <lma@suse.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
When detaching an <interface/> from a domain, the MAC address is
parsed and if not present one is generated. If no corresponding
interface is found in the domain, the following error is
reported:
error: operation failed: no device matching mac address 52:54:00:75:32:5b found
where the MAC address is the auto generated one. This might be
very confusing. Solution to this is to ignore auto generated MAC
address when looking up the device.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
It will come handy to know if the MAC address was generated (e.g.
during XML parse) or if it was parsed since provided by user in
the XML.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Found by Coverity. If virNWFilterHashTablePut, then the 3rd arg @val
must be free'd since it would be leaked.
This also fixes potential problem on the error path where the caller
could assume the virNWFilterHashTablePut was successful when in fact
it failed leading to other issues.
Rather than using loop break;'s in order to force a return
of rc = -1, let's just return -1 immediately on the various
error paths and then return 0 on the success path.
This is normally not an issue since the tests which use mocked open() do
not create files. But once coverage build is enabled, gcov_open will use
O_CREATE and real_open will read random data rather than the actual mode
argument.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
virDomainDiskSourceParse got to the point of being an ugly spaghetti
mess by adding more and more stuff into it. Split out parsing of network
disk information into a separate function so that it stays contained.
Building RPM should only be allowed on a supported platform, but
unpacking the source and applying all patches can be done anywhere.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
We get a question every now and then about why hibernation works when
suspend-to-disk is disabled and similar. Let's hope that, by documenting the
obvious more blatantly, people will get more informed.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
On pure success paths, virNWFilterIPAddrMapAddIPAddr was validly
consuming the input @addr; however, on failure paths it was possible
that virNWFilterVarValueCreateSimple succeed, but virNWFilterHashTablePut
failed resulting in virNWFilterVarValueFree being called to clean
up @val which also cleaned up the input @addr. Thus the caller had
no way to determine on failure whether it too should clean up the
passed parameter.
Instead, let's create a copy of the input @addr, then handle that
properly in the API allowing/forcing the caller to free it's own
copy of the input parameter.
The test suite has hardcoded /etc/pki/qemu as the cert dir, but this
only works if configure has --sysconfdir=/etc passed. We must set the
vxhs cert dir to a stable path in the test suite.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Alter qemu command line generation in order to possibly add TLS for
a suitably configured domain.
Sample TLS args generated by libvirt -
-object tls-creds-x509,id=objvirtio-disk0_tls0,dir=/etc/pki/qemu,\
endpoint=client,verify-peer=yes \
-drive file.driver=vxhs,file.tls-creds=objvirtio-disk0_tls0,\
file.vdisk-id=eb90327c-8302-4725-9e1b-4e85ed4dc251,\
file.server.type=tcp,file.server.host=192.168.0.1,\
file.server.port=9999,format=raw,if=none,\
id=drive-virtio-disk0,cache=none \
-device virtio-blk-pci,bus=pci.0,addr=0x4,drive=drive-virtio-disk0,\
id=virtio-disk0
Update the qemuxml2argvtest with a couple of examples. One for a
simple case and the other a bit more complex where multiple VxHS disks
are added where at least one uses a VxHS that doesn't require TLS
credentials and thus sets the domain disk source attribute "tls = 'no'".
Update the hotplug to be able to handle processing the tlsAlias whether
it's to add the TLS object when hotplugging a disk or to remove the TLS
object when hot unplugging a disk. The hot plug/unplug code is largely
generic, but the addition code does make the VXHS specific checks only
because it needs to grab the correct config directory and generate the
object as the command line would do.
Signed-off-by: Ashish Mittal <Ashish.Mittal@veritas.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
Introduce a function to setup any TLS needs for a disk source.
If there's a configuration or other error setting up the disk source
for TLS, then cause the domain startup to fail.
For VxHS, follow the chardevTLS model where if the src->haveTLS hasn't
been configured, then take the system/global cfg->haveTLS setting for
the storage source *and* mark that we've done so via the tlsFromConfig
setting in storage source.
Next, if we are using TLS, then generate an alias into a virStorageSource
'tlsAlias' field that will be used to create the TLS object and added to
the disk object in order to link the two together for QEMU.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Add an optional virTristateBool haveTLS to virStorageSource to
manage whether a storage source will be using TLS.
Sample XML for a VxHS disk:
<disk type='network' device='disk'>
<driver name='qemu' type='raw' cache='none'/>
<source protocol='vxhs' name='eb90327c-8302-4725-9e1b-4e85ed4dc251' tls='yes'>
<host name='192.168.0.1' port='9999'/>
</source>
<target dev='vda' bus='virtio'/>
</disk>
Additionally add a tlsFromConfig boolean to control whether the TLS
setting was due to domain configuration or qemu.conf global setting
in order to decide whether to Format the haveTLS setting for either
a live or saved domain configuration file.
Update the qemuxml2xmltest in order to add a test to show the proper
parsing.
Also update the docs to describe the tls attribute.
Signed-off-by: Ashish Mittal <Ashish.Mittal@veritas.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
