When reading in an XML definition for a SCSI target device, the name
property of struct scsi_target refers to the @target element.
Let's fix this obvious typo and also extend the XML schema to provide
validation.
Signed-off-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Until now, the libxl driver ignored any <hap> setting in domain XML
and deferred to libxl, which enables hap if not specified. While
this is a good default, it prevents disabling hap if desired.
This change allows disabling hap with <hap state='off'/>. hap is
explicitly enabled with <hap/> or <hap state='on/>. Absense of <hap>
retains current behavior of deferring default state to libxl.
hap is enabled by default in xm and xl config and usually only
specified when it is desirable to disable hap (hap = 0). Change
the xm,xl <-> xml converter to behave similarly. I.e. only
produce 'hap = 0' when <hap state='off'/> and vice versa.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Most hypervisors use Hardware Assisted Paging by default and don't
require specifying the feature in domain conf. But some hypervisors
support disabling HAP on a per-domain basis. To enable HAP by default
yet provide a knob to disable it, extend the <hap> feature with a
'state=on|off' attribute, similar to <pvspinlock> and <vmport> features.
In the absence of <hap>, the hypervisor default (on) is used. <hap>
without the state attribute would be the same as <hap state='on'/> for
backwards compatibility. And of course <hap state='off'/> disables hap.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
The function already takes two bool arguments, switching to flags makes
it a lot easier to read. Especially in case we need to add another
boolean in the future.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
In post-copy mode none of the hosts has a complete guest state and
rolling back migration is impossible. Thus aborting it would be
equivalent to destroying the domain.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When migration fails in the post-copy mode, it's impossible to just kill
the destination domain and resume the source since the source no longer
contains current guest state. Let's mark domains on both sides as
VIR_DOMAIN_PAUSED_POSTCOPY_FAILED to let the upper layer decide what to
do with them.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When destination libvirtd is restarted during migration in Finish phase
just after the point we started guest CPUs, we should not kill the
domain.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Migration enters "postcopy-active" state after QEMU switches to
post-copy and pauses guest CPUs. From libvirt's point of view this state
is similar to "completed" because we need to transfer guest execution to
the destination host.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
To use post-copy one has to start the migration with
VIR_MIGRATE_POSTCOPY flag and, while migration is in progress, call
virDomainMigrateStartPostCopy() to switch from pre-copy to post-copy.
Signed-off-by: Cristian Klein <cristiklein@gmail.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
VIR_DOMAIN_EVENT_SUSPENDED_POSTCOPY and VIR_DOMAIN_PAUSED_POSTCOPY are
used on the source host once migration enters post-copy mode (which
means the domain gets paused on the source. After the destination host
takes over the execution of the domain, its virtual CPUs are resumed and
the domain enters VIR_DOMAIN_RUNNING_POSTCOPY state and
VIR_DOMAIN_EVENT_RESUMED_POSTCOPY event is emitted.
In case migration fails during post-copy mode and none of the hosts have
complete state of the domain, both domains will remain paused with
VIR_DOMAIN_PAUSED_POSTCOPY_FAILED reason and an upper layer may decide
what to do.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
This allows setting the address in host and/or network order and makes
the naming consistent. Now you don't need to call [hn]to[nh]l()
functions as that is taken care of by these functions. Also, now
the *NetOrder take the address in network order, the other functions in
host order so the naming and usage is consistent. Some places were
having the address in network order and calling ntohl() just so the
original function can call htonl() again. This makes it nicer to read.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If a <graphics type='spice'> has no port nor tlsPort set, the generated
QEMU command line will contain -spice port=0.
This is later going to be ignored by spice-server, but it's better not
to add it at all in this situation.
As an empty -spice is not allowed, we still need to append port=0 if we
did not add any other argument.
The end goal is to avoid adding -spice port=0,addr=127.0.0.1 to QEMU command
line when no SPICE port is specified in libvirt XML.
Currently, the code relies on port=xx to always be present, so subsequent
args can be unconditionally appended with a leading ','. Since port=0
will no longer be added in a subsequent commit, we append a ',' to every
arg instead of prepending, and remove the last one before adding it to
the arg list.
It's just a combination of AddImplicitControllers, and AddConsoleCompat.
Every caller that wants ImplicitControllers also wants the ConsoleCompat
AFAICT, so lump them together. We also need it for future patches.
Even if nss is disabled, the build system tries to build some
targets like libnss_libvirt_impl.la and nsstest. Hide those
under the "if WITH_NSS" block like the rest of NSS plugin bits.
Judging by how the whitelist has skewed quite far from the original
error message, I think it's better to just drop these.
If someone wants to revive this check I suggest implementing it on
a per-HV driver basis with PostParse callbacks.
If we expose this information, which is one byte in every PCI config
file, we let all mgmt apps know whether the device itself is an endpoint
or not so it's easier for them to decide whether such device can be
passed through into a VM (endpoint) or not (*-bridge).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1317531
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Best viewed with '-w' as this is just an adjustment for future patch to
be readable without that.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The only purpose of this test is to catch possible linking
problems with libnss_libvirt.so.2.
One of the problems I faced was that the NSS plugin was unloaded
immediately after it got loaded and the name resolution process
continued with next configured option. Without any error. It was
very hard to debug why until I created this simple test and found
out immediately that there were some symbols missing. The reason
why problem was not caught in nsstest is that in the test we want
to use all the fancy stuff and therefore link it with libvirt.la.
So even if there's a symbol missing in the NSS plugin it will be
found in the libvirt.la.
But even after I resolved the issue we still need this test
because files the NSS plugin is built from are still live (mostly
those under utils/ dir). So as they change new symbol might be
required which would render the NSS plugin unusable.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This function is a different beast compared to previous ones.
But yet again, nothing surprising is happening here.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The implementation is pretty straightforward. Moreover, because
of the nature of things, gethostbyname_r and gethostbyname2_r can
be implemented at the same time too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Name Service Switch is a glibc feature responsible for many
things. Translating domain names into IP addresses and vice versa
is just one of them. However, currently it's the only
functionality that this commit is tickling. Well, in this commit
the plugin skeleton is introduced. Implementation to come in next
patches.
Because of the future testing, where the implementation is to be
linked with a test, this needs to go into static library. Linking
a program with an .so statically is not portable. Therefore a
dummy libnss_libvirt_impl library is being introduced too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This is a missing counterpart for virSocketAddrSetIPv4Addr()
and is going to be needed later in the tests.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This function is going to be used later in such context where the
argument makes no sense. Teach this function to cope with that
instead of the caller having to deal with passing some dummy
argument.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
These functions are going to be reused very shortly. So instead
of duplicating the code, lets move them into utils module.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
None of the existing domXML configs under tests/* specify a
default cache mode since default generally means "use the
hypervisor default" and is left unset by the various hypervisor
drivers. Add a config to tests/domainschemadata that specifies
cache='default'.
Commit id '4f846170' added printing of a new field 'part_separator';
however, neglected to do so when there was an "freeExtent" defined
for the device (as there would be when the disk pool was started).
This patch adjusts the logic to appropriately format the device path and
if there the part_separator attribute.
Commit 'ef2ab8fd' moved just the virDomainConfNWFilterTeardown and left
the logic to save/restore the current error essentially doing nothing
in the error path for qemuBuildCommandLine. So move it to where it
was meant to be.
Although the original code would reset the filter on command creation
errors after building the network command portion and commit 'ef2ab8fd'
altered that logic, the teardown is called during qemuProcessStop from
virDomainConfVMNWFilterTeardown and that code has the save/restore
last error logic, so just allow that code to handle the teardown rather
than running it twice. The qemuProcessStop would be called in the failure
path of qemuBuildCommandLine.
Currently we spawn couple of binaries in our test suite.
Moreover, we provide some spoofed versions of system binaries
hoping that those will be executed instead of the system ones.
For instance, for testing SSH socket we have written our own ssh
binary for producing predictable results. We certainly don't want
to execute the system ssh binary.
However, in order to prefer our binaries over system ones, we
need to set PATH environment variable. But this is done only at
the Makefile level. So if anybody runs a test by hand that
expects our spoofed binary, the test ends up executing real
system binaries. This is not good. In fact, it's terribly wrong.
The fix lies in a small trick - putting our build directory at
the beginning of the PATH environment variable in each test.
Hopefully, since every test has this VIRT_TEST_MAIN* wrapper, we
can fix this at a single place.
Moreover, while this removes setting PATH for our tests written
in bash, it's safe as we are not calling anything ours that would
require PATH change there.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
We include the file in plenty of places. This is mostly due to
historical reasons. The only place that needs something from the
header file is storage_backend_fs which opens _PATH_MOUNTED. But
it gets the file included indirectly via mntent.h. At no other
place in our code we need _PATH_.*. Drop the include and
configure check then.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
