AFAIK there aren't any cases where we will/should hit the old code
path for our supported qemu versions, so drop the old code.
Massive test suite churn follows
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
This patch teaches testutil how to read multi-line input files with
backspace-newline line continuation markers.
The patch also breaks up all the single-line arguments test input files into
multi-line files with lines shorter than 80 characters.
The current code for using -drive simply sets the -drive 'index'
parameter. QEMU internally converts this to bus/unit depending
on the type of drive. This does not give us precise control over
the bus/unit assignment though. This change switches over to make
libvirt explicitly calculate the bus/unit number.
In addition bus/unit/index are actually irrelevant for VirtIO
disks, since each virtio disk is a separate PCI device. No disk
controller is involved.
Doing the conversion to bus/unit in libvirt allows us to correctly
attach SCSI controllers when required.
* src/qemu/qemu_conf.c: Specify bus/unit instead of index for
disks
* tests/qemuxml2argvdata/qemuxml2argv-disk*.args: Switch over from
using index=NNNN, to bus=NN, unit=NN for SCSI/IDE/Floppy disks
Introduce a new type="dir" mode for <disks> that allows use of
QEMU's virtual FAT block device driver. eg
<disk type='dir' device='floppy'>
<source dir='/tmp/test'/>
<target dev='fda' bus='fdc'/>
<readonly/>
</disk>
gets turned into
-drive file=fat:floppy:/tmp/test,if=floppy,index=0
Only read-only disks are supported with virtual FAT mode
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add type="dir"
* docs/schemas/domain.rng: Document new disk type
* src/xen/xend_internal.c, src/xen/xm_internal.c: Raise error for
unsupported disk types
* tests/qemuxml2argvdata/qemuxml2argv-disk-cdrom-empty.args: Fix
empty disk file handling
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.xml,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.xml
tests/qemuxml2argvtest.c: Test QEMU vitual FAT driver
* src/qemu/qemu_conf.c: Support generating fat:/some/dir type
disk args
* src/security/security_selinux.c: Temporarily skip labelling
of directory based disks
We keep support for the pty based monitor so that we can re-connect
to VMs started by older versions of libvirtd.
* src/domain_conf.c: handle formatting and parsing unix monitors
* src/qemu_driver.c: add qemudOpenMonitorUnix(), remove the monitor
pty path searching from qemudFindCharDevicePTYs(), switch
qemudStartVMDaemon() and qemuDomainXMLToNative() to using a unix
monitor
* tests/qemuxml2argvtest.c: switch to using a unix monitor
* tests/qemuxml2argvdata/qemuxml2argv-*.args: update test data
virExec will write out the pid of the daemonized process only. Use this
in the QEMU driver, rather than QEMU's pidfile, so we can catch errors we
might miss if the emulator bails early.
* tests/qemuxml2argvtest.c (testCompareXMLToArgvFiles): Adjust the
code that creates "actual" output, so that it too produces a
newline-terminated buffer.
* tests/qemuxml2argvdata/*.args: Append a newline to each, via:
for i in $(find|grep '\.args$'); do echo >> $i;done
handling code. In particular, if you had a section of XML like:
<disk type='file' device='cdrom'>
<target dev='hdc' bus='ide'/>
<readonly/>
</disk>
This used to work with older libvirt, but now fails. This is because we are
actually passing the literal string (null) to the qemu command-line, which qemu
barfs on. This patch fixes it up by making it blank, which allows qemu to
continue on it's merry way.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
