A PCI device may have the capability to setup virtual functions (VFs)
but have them currently all disabled. Prior to this patch, if that was
the case the the node device XML for the device wouldn't report any
virtual_functions capability.
With this patch, if a file called "sriov_totalvfs" is found in the
device's sysfs directory, its contents will be interpreted as a
decimal number, and that value will be reported as "maxCount" in a
capability element of the device's XML, e.g.:
<capability type='virtual_functions' maxCount='7'/>
This will be reported regardless of whether or not any VFs are
currently enabled for the device.
NB: sriov_numvfs (the number of VFs currently active) is also
available in sysfs, but that value is implied by the number of items
in the list that is inside the capability element, so there is no
reason to explicitly provide it as an attribute.
sriov_totalvfs and sriov_numvfs are available in kernels at least as far
back as the 2.6.32 that is in RHEL6.7, but in the case that they
simply aren't there, libvirt will behave as it did prior to this patch
- no maxCount will be displayed, and the virtual_functions capability
will be absent from the device's XML when 0 VFs are enabled.
commit db488c79 assumed that dnsmasq would complete IPv6 DAD before
daemonizing, but in reality it doesn't wait, which creates problems
when libvirt's bridge driver sets the matching "dummy tap device" to
IFF_DOWN prior to DAD completing.
This patch waits for DAD completion by periodically polling the kernel
using netlink to check whether there are any IPv6 addresses assigned
to bridge which have a 'tentative' state (if there are any in this
state, then DAD hasn't yet finished). After DAD is finished, execution
continues. To avoid an endless hang in case something was wrong with
the kernel's DAD, we wait a maximum of 5 seconds.
The internal representation of a JSON array counts the items in
size_t. However, for some reason, when asking for the count it's
reported as int. Firstly, we need the function to return a signed
type as it's returning -1 on an error. But, not every system has
integer the same size as size_t. Therefore, lets return ssize_t.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There's a check right at the beginning of the function that
shortcuts if the function was called over all NULL arguments.
However, this was meant just as a fool-proof check so that we
don't crash if function is used in a bad manner. Anyway, it makes
Coverity unhappy as it then thinks any of the arguments could be
NULL. Well, with the current state of the code it can't.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
It may happen that an interface don't have any bandwidth set and
a new one is to be set. In that case, @ifaceBand will be NULL.
This will cause troubles later in the code when deciding what to
do.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So, if a domain vNIC's bandwidth has been successfully set, it's
possible that because @floor is set on network's bridge, this
part may need updating too. And that's exactly what this function
does. While the previous commit introduced a function to check if
@floor can be satisfied, this does all the hard work. In general,
there may be three, well four possibilities:
1) No change in @floor value (either it remain unset, or its
value hasn't changed)
2) The @floor value has changed from a non-zero to a non-zero
value
3) New @floor is to be set
4) Old @floor must be cleared out
The difference between 2), 3) and 4) is, that while in 2) the QoS
tree on the network's bridge already has a special class for the
vNIC, in 3) the class must be created from scratch. In 4) it must
be removed. Fortunately, we have helpers for all three
interesting cases.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When a domain vNIC's bandwidth is to be changed (at runtime) it is
possible that guaranteed minimal bandwidth (@floor) will change too.
Well, so far it is, because we still don't have an implementation that
allows setting it dynamically, so it's effectively erased on:
#virsh domiftune $dom vnet0 --inbound 0
However, that's slightly unfortunate. We do some checks on domain
startup to see if @floor can be guaranteed. We ought do the same if
QoS is changed at runtime.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This is no functional change. It's just that later in the series we
will need to pass class_id as an integer.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There are now many more reasons that virSocketAddrGetRange() could
fail, so it is much more informative to report the error there instead
of in the caller. (one of the two callers was previously assuming
success, which is almost surely safe based on the parsing that has
already happened to the config by that time, but it still is nicer to
account for an error "just in case")
Part of fix for: https://bugzilla.redhat.com/show_bug.cgi?id=985653
This loop had automatic variable definitions mixed with code. This
patch moves the definitions to the top of the function and puts
cleanup for them at the bottom. No functional change.
Part of fix for: https://bugzilla.redhat.com/show_bug.cgi?id=985653
virSocketAddrGetRange() has been updated to take the network address
and prefix, and now checks that both the start and end of the range
are within that network, thus validating that the entire range of
addresses is in the network. For IPv4, it also checks that ranges to
not start with the "network address" of the subnet, nor end with the
broadcast address of the subnet (this check doesn't apply to IPv6,
since IPv6 doesn't have a broadcast or network address)
Negative tests have been added to the network update and socket tests
to verify that bad ranges properly generate an error.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=985653
To silence Coverity just add a 'p &&' in front of the check in
networkFindUnusedBridgeName after the strchr() call. Even though
we know it's not possible to have strchr return NULL since the only
way into the function is if there is a '%' in def->bridge or it's NULL.
Signed-off-by: John Ferlan <jferlan@redhat.com>
For some reason, we allow a bridge name with %d in it, which we replace
with an unsigned integer to form a bridge name that does not yet exist
on the host.
Do not blindly pass it to virAsprintf if it's not the only conversion,
to prevent crashing on input like:
<network>
<name>test</name>
<forward mode='none'/>
<bridge name='virbr%d%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s'/>
</network>
Ignore any template strings that do not have exactly one %d conversion,
like we do in various drivers before calling virNetDevTapCreateInBridgePort.
Since some people use the same naming convention as libvirt for bridge
devices they create outside the context of libvirt, it is much nicer
if we check for those devices when looking for a bridge device name to
auto-assign to a new network.
We already check that any auto-assigned bridge device name for a
virtual network (e.g. "virbr1") doesn't conflict with the bridge name
for any existing libvirt network (via virNetworkSetBridgeName() in
conf/network_conf.c).
We also want to check that the name doesn't conflict with any bridge
device created on the host system outside the control of libvirt
(history: possibly due to the ploriferation of references to libvirt's
bridge devices in HOWTO documents all around the web, it is not
uncommon for an admin to manually create a bridge in their host's
system network config and name it "virbrX"). To add such a check to
virNetworkBridgeInUse() (which is called by virNetworkSetBridgeName())
we would have to call virNetDevExists() (from util/virnetdev.c); this
function calls ioctl(SIOCGIFFLAGS), which everyone on the mailing list
agreed should not be done from an XML parsing function in the conf
directory.
To remedy that problem, this patch removes virNetworkSetBridgeName()
from conf/network_conf.c and puts an identically functioning
networkBridgeNameValidate() in network/bridge_driver.c (because it's
reasonable for the bridge driver to call virNetDevExists(), although
we don't do that yet because I wanted this patch to have as close to 0
effect on function as possible).
There are a couple of inevitable changes though:
1) We no longer check the bridge name during
virNetworkLoadConfig(). Close examination of the code shows that
this wasn't necessary anyway - the only *correct* way to get XML
into the config files is via networkDefine(), and networkDefine()
will always call networkValidate(), which previously called
virNetworkSetBridgeName() (and now calls
networkBridgeNameValidate()). This means that the only way the
bridge name can be unset during virNetworkLoadConfig() is if
someone edited the config file on disk by hand (which we explicitly
prohibit).
2) Just on the off chance that somebody *has* edited the file by hand,
rather than crashing when they try to start their malformed
network, a check for non-NULL bridge name has been added to
networkStartNetworkVirtual().
(For those wondering why I don't instead call
networkValidateBridgeName() there to set a bridge name if one
wasn't present - the problem is that during
networkStartNetworkVirtual(), the lock for the network being
started has already been acquired, but the lock for the network
list itself *has not* (because we aren't adding/removing a
network). But virNetworkBridgeInuse() iterates through *all*
networks (including this one) and locks each network as it is
checked for a duplicate entry; it is necessary to lock each network
even before checking if it is the designated "skip" network because
otherwise some other thread might acquire the list lock and delete
the very entry we're examining. In the end, permitting a setting of
the bridge name during network start would require that we lock the
entire network list during any networkStartNetwork(), which
eliminates a *lot* of parallelism that we've worked so hard to
achieve (it can make a huge difference during libvirtd startup). So
rather than try to adjust for someone playing against the rules, I
choose to instead give them the error they deserve.)
3) virNetworkAllocateBridge() (now removed) would leak any "template"
string set as the bridge name. Its replacement
networkFindUnusedBridgeName() doesn't leak the template string - it
is properly freed.
Rename it to virNetDevGetIPv4AddressIoctl and make
virNetDevGetIPAddress a wrapper around it, allowing
other ways of getting the address to be implemented,
and still falling back to the old method.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This function does not make any sense now, that network driver is
(almost) dropped. I mean, previously, when threads were
serialized, this function was there to check, if no other network
with the same name or UUID exists. However, nowadays that threads
can run more in parallel, this function is useless, in fact it
gives misleading return values. Consider the following scenario.
Two threads, both trying to define networks with same name but
different UUID (e.g. because it was generated during XML parsing
phase, whatever). Lets assume that both threads are about to call
networkValidate() which immediately calls
virNetworkObjIsDuplicate().
T1: calls virNetworkObjIsDuplicate() and since no network with
given name or UUID exist, success is returned.
T2: calls virNetworkObjIsDuplicate() and since no network with
given name or UUID exist, success is returned.
T1: calls virNetworkAssignDef() and successfully places its
network into the virNetworkObjList.
T2: calls virNetworkAssignDef() and since network with the same
name exists, the network definition is replaced.
Okay, this is mainly because virNetworkAssignDef() does not check
whether name and UUID matches. Well, lets make it so! And drop
useless function too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There's no need to lock the network driver, as network driver
initialization is done prior accepting any client. There's nobody
to hop in and do something over partially initialized driver. Nor
qemu driver is doing that.
==30532== Observed (incorrect) order is: acquisition of lock at 0x1439EF50
==30532== at 0x4C31A26: pthread_mutex_lock (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0x5324895: virMutexLock (virthread.c:88)
==30532== by 0x5307E86: virObjectLock (virobject.c:323)
==30532== by 0x5396440: virNetworkObjListForEach (network_conf.c:4511)
==30532== by 0x19B29308: networkStateInitialize (bridge_driver.c:686)
==30532== by 0x53E1CCC: virStateInitialize (libvirt.c:777)
==30532== by 0x11DEB7: daemonRunStateInit (libvirtd.c:906)
==30532== by 0x5324B6A: virThreadHelper (virthread.c:197)
==30532== by 0x4C30456: ??? (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0xA1EC1F2: start_thread (in /lib64/libpthread-2.19.so)
==30532== by 0xA4EDC8C: clone (in /lib64/libc-2.19.so)
==30532==
==30532== followed by a later acquisition of lock at 0x1439CD60
==30532== at 0x4C31A26: pthread_mutex_lock (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0x5324895: virMutexLock (virthread.c:88)
==30532== by 0x19B27B2C: networkDriverLock (bridge_driver.c:102)
==30532== by 0x19B27B60: networkGetDnsmasqCaps (bridge_driver.c:113)
==30532== by 0x19B2856A: networkUpdateState (bridge_driver.c:389)
==30532== by 0x53963E9: virNetworkObjListForEachHelper (network_conf.c:4488)
==30532== by 0x52E2224: virHashForEach (virhash.c:521)
==30532== by 0x539645B: virNetworkObjListForEach (network_conf.c:4512)
==30532== by 0x19B29308: networkStateInitialize (bridge_driver.c:686)
==30532== by 0x53E1CCC: virStateInitialize (libvirt.c:777)
==30532== by 0x11DEB7: daemonRunStateInit (libvirtd.c:906)
==30532== by 0x5324B6A: virThreadHelper (virthread.c:197)
==30532==
==30532== Required order was established by acquisition of lock at 0x1439CD60
==30532== at 0x4C31A26: pthread_mutex_lock (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0x5324895: virMutexLock (virthread.c:88)
==30532== by 0x19B27B2C: networkDriverLock (bridge_driver.c:102)
==30532== by 0x19B28DF9: networkStateInitialize (bridge_driver.c:609)
==30532== by 0x53E1CCC: virStateInitialize (libvirt.c:777)
==30532== by 0x11DEB7: daemonRunStateInit (libvirtd.c:906)
==30532== by 0x5324B6A: virThreadHelper (virthread.c:197)
==30532== by 0x4C30456: ??? (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0xA1EC1F2: start_thread (in /lib64/libpthread-2.19.so)
==30532== by 0xA4EDC8C: clone (in /lib64/libc-2.19.so)
==30532==
==30532== followed by a later acquisition of lock at 0x1439EF50
==30532== at 0x4C31A26: pthread_mutex_lock (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0x5324895: virMutexLock (virthread.c:88)
==30532== by 0x5307E86: virObjectLock (virobject.c:323)
==30532== by 0x538A09C: virNetworkAssignDef (network_conf.c:527)
==30532== by 0x5391EB2: virNetworkLoadState (network_conf.c:3008)
==30532== by 0x53922D4: virNetworkLoadAllState (network_conf.c:3128)
==30532== by 0x19B2929A: networkStateInitialize (bridge_driver.c:671)
==30532== by 0x53E1CCC: virStateInitialize (libvirt.c:777)
==30532== by 0x11DEB7: daemonRunStateInit (libvirtd.c:906)
==30532== by 0x5324B6A: virThreadHelper (virthread.c:197)
==30532== by 0x4C30456: ??? (in /usr/lib64/valgrind/vgpreload_helgrind-amd64-linux.so)
==30532== by 0xA1EC1F2: start_thread (in /lib64/libpthread-2.19.so)
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The following is a long winded way to say this patch is avoiding a
false positive.
Coverity complains that calling networkPlugBandwidth() could eventually
end up with a NULL dereference on iface->bandwidth because in the
networkAllocateActualDevice there's a check of 'iface->bandwidth'
before deciding to try to use the 'portgroup' if it exists or to not
perferm the virNetDevBandwidthCopy if 'bandwidth' is not NULL.
Later in networkPlugBandwidth the 'iface->bandwidth' is sourced from
virDomainNetGetActualBandwidth - which would be either iface->bandwidth
or (preferably) iface->data.network.actual->bandwidth which would have
been filled in from either 'iface->bandwidth' or 'portgroup->bandwidth'
back in networkAllocateActualDevice
There *is* a check in networkCheckBandwidth for the result of the
virDomainNetGetActualBandwidth being NULL and a return 1 based on
that which would cause networkPlugBandwidth to exit properly and thus
never hit the condition that Coverity complains about.
However, since Coverity checks all paths - it somehow believes that
a return of 0 by networkCheckBandwidth in this condition would end
up causing the possible NULL dereference. The "fix" to silence Coverity
is to not have networkCheckBandwidth also call virDomainNetGetActualBandwidth
in order to get the ifaceBand, but rather have it accept it as an argument
which causes Coverity to "see" that it's the exit condition of 1 that won't
have the possible NULL dereference. Since we're passing that, I added the
passing of iface->mac rather than passing iface as well. This just hopefully
makes sure someone doesn't undo this in the future...
Valgrind detected a leak:
==17820== 102 (56 direct, 46 indirect) bytes in 1 blocks are definitely lost in loss record 479 of 646
==17820== at 0x4A08946: calloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==17820== by 0x508521A: virAllocVar (viralloc.c:560)
==17820== by 0x50D9FCA: virObjectNew (virobject.c:193)
==17820== by 0x50A4FD9: dnsmasqCapsNewEmpty (virdnsmasq.c:784)
==17820== by 0x50A514E: dnsmasqCapsNewFromBinary (virdnsmasq.c:830)
==17820== by 0x1B508287: networkStateInitialize (bridge_driver.c:666)
It looks like commit 172acef introduced the problem, because
networkGetDnsmasqCaps() increments the reference count but an
early exit never does a matching decrement.
* src/network/bridge_driver.c (networkStateCleanup): Plug leak.
Signed-off-by: Eric Blake <eblake@redhat.com>
Now that the network driver lock is ash heap of history,
we can use more of networkObjFromNetwork().
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Now that we have fine grained locks, there's no need to
lock the whole driver. We can rely on self-locking APIs.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This is not an immutable pointer and can change during lifetime.
Therefore, in order to drop network driver lock, we must use an
internal accessor which does not lock the network driver yet, but
it will soon. Now it merely returns an referenced object.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Well, network driver code has the driver accessible as a global
variable. This makes any rework hard, as it's unclear where the
variable is accessed and/or modified. Lets just pass the driver
as a parameter to all functions where needed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch turns both virNetworkObjFindByUUID() and
virNetworkObjFindByName() to return an referenced object so that
even if caller unlocks it, it's for sure that object won't
disappear meanwhile. Especially if the object (in general) is
locked and unlocked during the caller run.
Moreover, this commit is nicely small, since the object unrefing
can be done in virNetworkObjEndAPI().
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So far, this is pure code replacement. But once we introduce
reference counting to virNetworkObj this will be more handy as
there'll be only one function to change: virNetworkObjEndAPI().
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So far it's just a structure which happens to have 'Obj' in its
name, but otherwise it not related to virObject at all. No
reference counting, not virObjectLock(), nothing.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Undefining a running, autostarted domain removes the autostart link, but
dom->autostart is not cleared. If the domain is subsequently redefined,
libvirt thinks it is already autostarted and will not create the link
even if requested:
# virsh dominfo example | grep Autostart
Autostart: enable
# ls /etc/libvirt/qemu/autostart/example.xml
/etc/libvirt/qemu/autostart/example.xml
# virsh undefine example
Domain example has been undefined
# virsh define example.xml
Domain example defined from example.xml
# virsh dominfo example | grep Autostart
Autostart: enable
# virsh autostart example
Domain example marked as autostarted
# ls /etc/libvirt/qemu/autostart/example.xml
ls: cannot access /etc/libvirt/qemu/autostart/example.xml: No such file or directory
This commit ensures dom->autostart is cleared whenever the config and
autostart link (if present) are removed.
The bridge network driver cleared this flag itself in networkUndefine.
This commit moves this into virNetworkDeleteConfig for symmetry with
virDomainDeleteConfig, and to ensure it is not missed in future network
drivers.
Signed-off-by: Michael Chapman <mike@very.puzzling.org>
Well, one day this will be self-locking object, but not today.
But lets prepare the code for that! Moreover,
virNetworkObjListFree() is no longer needed, so turn it into
virNetworkObjListDispose().
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In order to hide the object internals (and use just accessors
everywhere), lets store a pointer to the object, instead of object
itself.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Instead of copying the whole object onto stack when calling the
function, just pass the pointer to the object and save up some
space on the stack. Moreover, this prepares the code to hide the
virNetworkObjList structure into network_conf.c and use accessors
only.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Moreover, there are two points within the function, where we're
missing 'goto cleanup'. Fix this too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Okay, this is mainly for educational purposes since is called
from single point only with all the possible locks held. So
there's no way for other thread to hop in and do something wrong.
Nevertheless, we should not give bad example.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
We have this function networkObjFromNetwork() which for given
virNetworkPtr tries to find corresponding virNetworkObjPtr. If no
object is found, a nice error message is printed out:
no network with matching uuid '$uuid' ($name)
Let's improve the error message produced by networkLookupByUUID to
follow that logic.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
libvirt was unconditionally calling virNetDevBandwidthClear() for
every interface (and network bridge) of a type that supported
bandwidth, whether it actually had anything set or not. This doesn't
hurt anything (unless ifname == NULL!), but is wasteful.
This patch makes sure that all calls to virNetDevBandwidthClear() are
qualified by checking that the interface really had some bandwidth
setup done, and checks for a null ifname inside
virNetDevBandwidthClear(), silently returning success if it is null
(as well as removing the ATTRIBUTE_NONNULL from that function's
prototype, since we can't guarantee that it is never null,
e.g. sometimes a type='ethernet' interface has no ifname as it is
provided on the fly by qemu).
The function that parses the <forward> subelement of a network used to
fail/log an error if the network definition contained both a <pf>
element as well as at least one <interface> or <address> element. That
check was present because the configuration of a network should have
either one <pf>, one or more <interface>, or one or more <address>,
but never combinations of multiple kinds.
This caused a problem when libvirtd was restarted with a network
already active - when a network with a <pf> element is started, the
referenced PF (Physical Function of an SRIOV-capable network card) is
checked for VFs (Virtual Functions), and the <forward> is filled in
with a list of all VFs for that PF either in the form of their PCI
addresses (a list of <address>) or their netdev names (a list of
<interface>); the <pf> element is not removed though. When libvirtd is
restarted, it parses the network status and finds both the original
<pf> from the config, as well as the list of either <address> or
<interface>, fails the parse, and the network is not added to the
active list. This failure is often obscured because the network is
marked as autostart so libvirt immediately restarts it.
It seems odd to me that <interface> and <address> are stored in the
same array rather than keeping two separate arrays, and having
separate arrays would have made the check much simpler. However,
changing to use two separate arrays would have required changes in
more places, potentially creating more conflicts and (more
importantly) more possible regressions in the event of a backport, so
I chose to keep the existing data structure in order to localize the
change.
It appears that this problem has been in the code ever since support
for <pf> was added (0.9.10), but until commit
34cc3b2f10 (first in libvirt 1.2.4)
networks with interface pools were not properly marked as active on
restart anyway, so there is no point in backporting this patch any
further than that.
Not all files we want to find using virFileFindResource{,Full} are
generated when libvirt is built, some of them (such as RNG schemas) are
distributed with sources. The current API was not able to find source
files if libvirt was built in VPATH.
Both RNG schemas and cpu_map.xml are distributed in source tarball.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When defining and creating networks, we have been checking to make
sure there is only a single "default" portgroup, but haven't verified
that no two portgroups have the same name. We *do* check for multiple
definitions when updating the portgroups in an existing network
though.
This patch adds a check to networkValidate(), which is called when a
network is defined or created, to disallow duplicate names. It would
actually make sense to do this in the network XML parser (since it's
not really "something that might make sense but isn't supported by
this driver", but is instead "something that should never be
allowed"), but doing that carries the danger of causing errors when
rereading the config of existing networks when libvirtd is restarted
after an upgrade, and that would result in networks disappearing from
libvirt's list. (I'm thinking I should change the error to "XML_ERROR"
instead of "UNSUPPORTED", even though that's not the type of error
that networkValidate is intended for)
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1115858
For stateless, client side drivers, it is never correct to
probe for secondary drivers. It is only ever appropriate to
use the secondary driver that is associated with the
hypervisor in question. As a result the ESX & HyperV drivers
have both been forced to do hacks where they register no-op
drivers for the ones they don't implement.
For stateful, server side drivers, we always just want to
use the same built-in shared driver. The exception is
virtualbox which is really a stateless driver and so wants
to use its own server side secondary drivers. To deal with
this virtualbox has to be built as 3 separate loadable
modules to allow registration to work in the right order.
This can all be simplified by introducing a new struct
recording the precise set of secondary drivers each
hypervisor driver wants
struct _virConnectDriver {
virHypervisorDriverPtr hypervisorDriver;
virInterfaceDriverPtr interfaceDriver;
virNetworkDriverPtr networkDriver;
virNodeDeviceDriverPtr nodeDeviceDriver;
virNWFilterDriverPtr nwfilterDriver;
virSecretDriverPtr secretDriver;
virStorageDriverPtr storageDriver;
};
Instead of registering the hypervisor driver, we now
just register a virConnectDriver instead. This allows
us to remove all probing of secondary drivers. Once we
have chosen the primary driver, we immediately know the
correct secondary drivers to use.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This adds a new "localOnly" attribute on the domain element of the
network xml. With this set to "yes", DNS requests under that domain
will only be resolved by libvirt's dnsmasq, never forwarded upstream.
This was how it worked before commit f69a6b987d, and I found that
functionality useful. For example, I have my host's NetworkManager
dnsmasq configured to forward that domain to libvirt's dnsmasq, so I can
easily resolve guest names from outside. But if libvirt's dnsmasq
doesn't know a name and forwards it to the host, I'd get an endless
forwarding loop. Now I can set localOnly="yes" to prevent the loop.
Signed-off-by: Josh Stone <jistone@redhat.com>
Moving code for parsing and formatting network routes to
networkcommon_conf helps reusing those routes for domains. The route
definition has been hidden to help reducing the number of unnecessary
checks in the format function.
Lack of a lease (whether mac is given or not) is a normal expected
scenario, since we are already filling in rv with nleases (which is
okay as 0 if there is no lease). There is no need to raise an error.
This fixes:
> virsh # net-dhcp-leases --mac 00:50:56:c0:00:01 default
> error: Failed to get leases info for default
> error: internal error: no lease with matching MAC address: 00:50:56:c0:00:01
Signed-off-by: Nehal J Wani <nehaljw.kkd1@gmail.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
When the bridge device for a network has macTableManager='libvirt' the
intent is that all kernel management of the bridge's MAC table
(Forwarding Database, or fdb, in the case of a Linux Host Bridge) be
disabled, with libvirt handling updates to the table instead. The
setup required for the bridge itself is:
1) set the "vlan_filtering" property of the bridge device to 1.
2) If the bridge has a "Dummy" tap device used to set a fixed MAC
address on the bridge (which is always the case for a bridge created
by libvirt, and never the case for a bridge created by the host system
network config), turn off learning and unicast_flood on this tap (this
is needed even though this tap is never IFF_UP, because the kernel
ignores the IFF_UP flag of devices when using their settings to
automatically decide whether or not to turn off promiscuous mode for
any attached device).
(1) is done both for libvirt-created/managed bridges, and for bridges
that are created by the host system config, while (2) is done only for
bridges created by libvirt (i.e. for forward modes of nat, routed, and
isolated bridges)
There is no attempt to turn vlan_filtering off when destroying the
network because in the case of a libvirt-created bridge, the bridge is
about to be destroyed anyway, and in the case of a system bridge, if
the other devices attached to the bridge could operate properly before
destroying libvirt's network object, they will continue to operate
properly (this is similar to the way that libvirt will enable
ip_forwarding whenever a routed/natted network is started, but will
never attempt to disable it if they are stopped).
At the time that the network driver allocates a connection to a
network, the tap device that will be used hasn't yet been created -
that will be done later by qemu (or lxc or whoever) - but if the
network has macTableManager='libvirt', then when we do get around to
creating the tap device, we will need to add an entry for it to the
network bridge's fdb (forwarding database) *and* turn off learning and
unicast_flood for that tap device in the bridge's sysfs settings. This
means that qemu needs to know both the bridge name as well as the
setting of macTableManager, so we either need to create a new API to
retrieve that info, or just pass it back in the ActualNetDef that is
created during networkAllocateActualDevice. We choose the latter
method, since it's already done for the bridge device, and it has the
side effect of making the information available in domain status.
(NB: in the future, I think that the tap device should actually be
created by networkAllocateActualDevice(), as that will solve several
other problems, but that is a battle for another day, and this
information will still be useful outside the network driver)
When the actualType of a virDomainNetDef is "network", it means that
we are connecting to a libvirt-managed network (routed, natted, or
isolated) which does use a bridge device (created by libvirt). In the
past we have required drivers such as qemu to call the public API to
retrieve the bridge name in this case (even though it is available in
the NetDef's ActualNetDef if the actualType is "bridge" (i.e., an
externally-created bridge that isn't managed by libvirt). There is no
real reason for this difference, and as a matter of fact it
complicates things for qemu. Also, there is another bridge-related
attribute (macTableManager) that will need to be available in both
cases, so this makes things consistent.
In order to avoid problems when restarting libvirtd after an update
from an older version that *doesn't* store the network's bridgename in
the ActualNetDef, we also need to put it in place during
networkNotifyActualDevice() (this function is run for each interface
of each domain whenever libvirtd is restarted).
Along with making the bridge name available in the internal object, it
is also now reported in the <source> element of the <interface> state
XML (or the <actual> subelement in the internally-stored format).
The one oddity about this change is that usually there is a separate
union for every different "type" in a higher level object (e.g. in the
case of a virDomainNetDef there are separate "network" and "bridge"
members of the union that pivots on the type), but in this case
network and bridge types both have exactly the same attributes, so the
"bridge" member is used for both type==network and type==bridge.
https://bugzilla.redhat.com/show_bug.cgi?id=1115292
In one of the previous commits (eafb53fe) we disallowed
network-wide bandwidth to some network types. However, we
forgot about <portgroups/> which can have <bandwidth/> too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch enables the helper program to detect event(s) triggered when
there is a change in lease length or expiry and client-id. This
transfers complete control of leases database to libvirt and obsoletes
use of the lease database file (<network-name>.leases). That file will
not be created, read, or written. This is achieved by adding the option
--leasefile-ro to dnsmasq and passing a custom env var to leaseshelper,
which helps us map events related to leases with their corresponding
network bridges, no matter what the event be.
Also, this requires the addition of a new non-lease entry in our custom
lease database: "server-duid". It is required to identify a DHCPv6
server.
Now that dnsmasq doesn't maintain its own leases database, it relies on
our helper program to tell it about previous leases and server duid.
Thus, this patch makes our leases program honor an extra action: "init",
in which it sends the known info in a particular format to dnsmasq
by printing it to stdout.
The drawback of this change is that upgrade to this new approach does
not transfer the existing leases for the network if the leaseshelper
wasn't already used.
Starting from libvirt-1.2.4, network state XML files moved to another
directory (see commit b9e95491) and libvirt automatically migrates the
network state files to a new location. However, the code used
dirent.d_type which is not supported by all filesystems. Thus, when
libvirt was upgraded on a host which used such filesystem, network state
XMLs were not properly moved and running networks disappeared from
libvirt.
This patch falls back to lstat() whenever dirent.d_type is DT_UNKNOWN to
fix this issue.
https://bugzilla.redhat.com/show_bug.cgi?id=1167145
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
The shared network driver is stateful and inside the daemon so
there is no need to use the networkPrivateData field to get the
driver handle. Just access the global driver handle directly.
Many places already directly accessed the global driver handle
in any case, so the code could never work without relying on
this.
As is done with other items such as vlan, virtualport, and bandwidth,
set the actual trustGuestRxFilters value to be used by a domain
interface according to a merge of the same attribute in the interface,
portgroup, and network in use. the interface setting always takes
precedence (if specified), followed by portgroup, and finally the
setting in the network is used if it's not specified in the interface
or portgroup.
Our style overwhelmingly uses hanging braces (the open brace
hangs at the end of the compound condition, rather than on
its own line), with the primary exception of the top level function
body. Fix the few remaining outliers, before adding a syntax
check in a later patch.
* src/interface/interface_backend_netcf.c (netcfStateReload)
(netcfInterfaceClose, netcf_to_vir_err): Correct use of { in
compound statement.
* src/conf/domain_conf.c (virDomainHostdevDefFormatSubsys)
(virDomainHostdevDefFormatCaps): Likewise.
* src/network/bridge_driver.c (networkAllocateActualDevice):
Likewise.
* src/util/virfile.c (virBuildPathInternal): Likewise.
* src/util/virnetdev.c (virNetDevGetVirtualFunctions): Likewise.
* src/util/virnetdevmacvlan.c
(virNetDevMacVLanVPortProfileCallback): Likewise.
* src/util/virtypedparam.c (virTypedParameterAssign): Likewise.
* src/util/virutil.c (virGetWin32DirectoryRoot)
(virFileWaitForDevices): Likewise.
* src/vbox/vbox_common.c (vboxDumpNetwork): Likewise.
* tests/seclabeltest.c (main): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Martin Kletzander pointed out in email that my commit 2a193f64
introduced a crash in networkCreateInterfacePool() during startup of
any network that doesn't have a <pf> subelement of its <forward>
element. He also supplied a patch.
http://www.redhat.com/archives/libvir-list/2014-August/msg00655.html
I expanded on that patch by cleaning up now-extraneous checks in the
callers of networkCreateInterfacePool().
Fortunately the offending patch hasn't been in any release, and hasn't
been (to my knowledge) backported to any other branch.
When a network is defined with "<pf dev='xyz'/>", libvirt will query
sysfs to learn the list of all virtual functions (VF) associated with
that Physical Function (PF) then populate the network's interface pool
accordingly. This action was previously done only when the first guest
actually requested an interface from the network. This patch changes
it to populate the pool immediately when the network is started. This
way any problems with the PF or its VFs will become apparent sooner.
Note that we can't remove the old calls to networkCreateInterfacePool
that happen whenever a guest requests an interface - doing so would be
asking for failures on hosts that had libvirt upgraded with a network
that had been started but not yet used.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1047818
networkCreateInterfacePool was a bit loose in its error cleanup, which
could result in a network definition with interfaces in the pool that
were NULL. This would in turn lead to a libvirtd crash when a guest
tried to attach an interface using the network with that pool.
In particular this would happen when creating a pool to be used for
macvtap connections. macvtap needs the netdev name of the virtual
function in order to use it, and each VF only has a netdev name if it
is currently bound to a network driver. If one of the VFs of a PF
happened to be bound to the pci-stub or vfio-pci driver (indicating
it's already in use for PCI passthrough), or no driver at all, it
would have no name. In this case networkCreateInterfacePool would
return an error, but would leave the netdef->forward.nifs set to the
total number of VFs in the PF. The interface attach that triggered
calling of networkCreateInterfacePool (it uses a "lazy fill" strategy)
would simply fail, but the very next attempt to attach an interface
using the same network pool would result in a crash.
This patch refactors networkCreateInterfacePool to bring it more in
line with current coding practices (label name, use of a switch with
no default case) as well as providing the following two changes to
behavior:
1) If a VF with no netdev name is encountered, just log a warning and
continue; only fail if exactly 0 devices are found to put in the pool.
2) If the function fails, clean up any partial interface pool and set
netdef->forward.nifs to 0.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1111455
Otherwise this beautiful error would be overwritten when
the function is called with a really high rate number:
2014-07-28 12:51:47.920+0000: 2304: error : virCommandWait:2399 :
internal error: Child process (/sbin/tc class add dev vnet0 parent 1:
classid 1:1 htb rate 4294968kbps) unexpected exit status 1: Illegal "rate"
Usage: ... qdisc add ... htb [default N] [r2q N]
default minor id of class to which unclassified packets are sent {0}
r2q DRR quantums are computed as rate in Bps/r2q {10}
debug string of 16 numbers each 0-3 {0}
... class add ... htb rate R1 [burst B1] [mpu B] [overhead O]
[prio P] [slot S] [pslot PS]
[ceil R2] [cburst B2] [mtu MTU] [quantum Q]
rate rate allocated to this class (class can still borrow)
burst max bytes burst which can be accumulated during idle period {computed}
mpu minimum packet size used in rate computations
overhead per-packet size overhead used in rate computations
linklay adapting to a linklayer e.g. atm
ceil definite upper class rate (no borrows) {rate}
cburst burst but for ceil {computed}
mtu max packet size we create rate map for {1600}
prio priority of leaf; lowe
https://bugzilla.redhat.com/show_bug.cgi?id=1043735
libvirt previously only touched an interface's disable_ipv6 setting in
sysfs if it needed to be set to 1, assuming that 0 is the
default. Apparently that isn't always the case though (kernel 3.15.7-1
in Arch Linux reportedly defaults a new interface's disable_ipv6
setting to 1) so this patch explicitly sets it to 0 or 1 as
appropriate.
Replace:
if (virBufferError(&buf)) {
virBufferFreeAndReset(&buf);
virReportOOMError();
...
}
with:
if (virBufferCheckError(&buf) < 0)
...
This should not be a functional change (unless some callers
misused the virBuffer APIs - a different error would be reported
then)
Instead of maintaining two very similar APIs, add the "@mac" parameter
to virNetworkGetDHCPLeases and kill virNetworkGetDHCPLeasesForMAC. Both
of those functions would return data the same way, so making @mac an
optional filter simplifies a lot of stuff.
Don't free individual JSON array members as the array will be freed at
the end. This may potentially lead to a crash although it didn't crash
on my setup.
Query the network driver for the path of the custom leases file for the given
virtual network and parse it to retrieve info.
src/network/bridge_driver.c:
* Implement networkGetDHCPLeases
* Implement networkGetDHCPLeasesForMAC
* Implement networkGetDHCPLeasesHelper
If the leasehelper_path couldn't be found the code would leak the
freshly constructed command structure. Re-arrange code to avoid the
problem.
Found by coverity, broken by baafe668fa.
In "src/conf/domain_conf.h" there are many enum declarations. The
cleanup in this header filer was started, but it wasn't enough and
there are many other files that has enum variables declared. So, the
commit was starting to be big. This commit finish the cleanup in this
header file and in other files that has enum variables, parameters,
or functions declared.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Introduce helper program to catch events from dnsmasq and maintain a custom
lease file per network. It supports dhcpv4 and dhcpv6. The file is saved as
"<interface-name>.status".
Each lease contains the following info:
<expiry-time (epoch time)> <mac> <iaid> <ip-address> <hostname> <clientid>
Example of custom leases file content:
[
{
"iaid": "1221229",
"ip-address": "2001:db8:ca2:2:1::95",
"mac-address": "52:54:00:12:a2:6d",
"hostname": "Fedora20",
"client-id": "00:04:1a:c1:d9:6b:5a:0a:e2:bc:f8:4b:1e:37:2e:38:22:55",
"expiry-time": 1393244216
},
{
"ip-address": "192.168.150.208",
"mac-address": "52:54:00:11:56:b3",
"hostname": "Wani-PC",
"client-id": "01:52:54:00:11:56:b3",
"expiry-time": 1393244248
}
]
src/Makefile.am:
* Add options to compile the helper program
src/network/bridge_driver.c:
* Introduce networkDnsmasqLeaseFileNameCustom()
* Invoke helper program along with dnsmasq
* Delete the .status file when corresponding n/w is destroyed.
src/network/leaseshelper.c
* Helper program to create the custom lease file
In "src/conf/" there are many enumeration (enum) declarations.
Similar to the recent cleanup to "src/util" directory, it's
better to use a typedef for variable types, function types and
other usages. Other enumeration and folders will be changed to
typedef's in the future. Most of the files changed in this commit
are reltaed to Network (network_conf.* and interface_conf.*) enums.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The check for a network being active during interface attach was being
done individually in several places (by both the lxc driver and the
qemu driver), but those places were too specific, leading to it *not*
being checked when allocating a connection/device from a macvtap or
hostdev network.
This patch puts a single check in networkAllocateActualDevice(), which
is always called before the any network interface is attached to any
type of domain. It also removes all the other now-redundant checks
from the lxc and qemu drivers.
NB: the following patches are prerequisites for this patch, in the
case that it is backported to any branch:
440beeb network: fix virNetworkObjAssignDef and persistence
8aaa5b6 network: create statedir during driver initialization
b9e9549 network: change location of network state xml files
411c548 network: set macvtap/hostdev networks active if their state
file exists
This fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=880483
libvirt attempts to determine at startup time which networks are
already active, and set their active flags. Previously it has done
this by assuming that all networks are inactive, then setting the
active flag if the network has a bridge device associated with it and
that bridge device exists. This is not useful for macvtap and hostdev
based networks, since they do not use a bridge device.
Of course the reason that such a check had to be done was that the
presence of a status file in the network "stateDir" couldn't be
trusted as an indicator of whether or not a network was active. This
was due to the network driver mistakenly using
/var/lib/libvirt/network to store the status files, rather than
/var/run/libvirt/network (similar to what is done by every other
libvirt driver that stores status xml for its objects). The difference
is that /var/run is cleared out when the host reboots, so you can be
assured that the state file you are seeing isn't just left over from a
previous boot of the host.
Now that the network driver has been switched to using
/var/run/libvirt/network for status, we can also modify it to assume
that any network with an existing status file is by definition active
- we do this when reading the status file. To fine tune the results,
networkFindActiveConfigs() is changed to networkUpdateAllState(),
and only sets active = 0 if the conditions for particular network
types are *not* met.
The result is that during the first run of libvirtd after the host
boots, there are no status files, so no networks are active. Any time
libvirtd is restarted, any network with a status file will be marked
as active (unless the network uses a bridge device and that device for
some reason doesn't exist).
For some reason these have been stored in /var/lib, although other
drivers (e.g. qemu and lxc) store their state files in /var/run.
It's much nicer to store state files in /var/run because it is
automatically cleared out when the system reboots. We can then use
existence of the state file as a convenient indicator of whether or
not a particular network is active.
Since changing the location of the state files by itself will cause
problems in the case of a *live* upgrade from an older libvirt that
uses /var/lib (because current status of active networks will be
lost), the network driver initialization has been modified to migrate
any network state files from /var/lib to /var/run.
This will not help those trying to *downgrade*, but in practice this
will only be problematic in two cases
1) If there are networks with network-wide bandwidth limits configured
*and in use* by a guest during a downgrade to "old" libvirt. In this
case, the class ID's used for that network's tc rules, as well as
the currently in-use bandwidth "floor" will be forgotten.
2) If someone does this: 1) upgrade libvirt, 2) downgrade libvirt, 3)
modify running state of network (e.g. add a static dhcp host, etc),
4) upgrade. In this case, the modifications to the running network
will be lost (but not any persistent changes to the network's
config).
This directory should be created when the network driver is first
started up, not just when a dhcp daemon is run. This hasn't posed a
problem in the past, because the directory has always been
pre-existing.
Experimentation showed that if virNetworkCreateXML() was called for a
network that was already defined, and then the network was
subsequently shutdown, the network would continue to be persistent
after the shutdown (expected/desired), but the original config would
be lost in favor of the transient config sent in with
virNetworkCreateXML() (which would then be the new persistent config)
(obviously unexpected/not desired).
To fix this, virNetworkObjAssignDef() has been changed to
1) properly save/free network->def and network->newDef for all the
various combinations of live/active/persistent, including some
combinations that were previously considered to be an error but didn't
need to be (e.g. setting a "live" config for a network that isn't yet
active but soon will be - that was previously considered an error,
even though in practice it can be very useful).
2) automatically set the persistent flag whenever a new non-live
config is assigned to the network (and clear it when the non-live
config is set to NULL). the libvirt network driver no longer directly
manipulates network->persistent, but instead relies entirely on
virNetworkObjAssignDef() to do the right thing automatically.
After this patch, the following sequence will behave as expected:
virNetworkDefineXML(X)
virNetworkCreateXML(X') (same name but some config different)
virNetworkDestroy(X)
At the end of these calls, the network config will remain as it was
after the initial virNetworkDefine(), whereas previously it would take
on the changes given during virNetworkCreateXML().
Another effect of this tighter coupling between a) setting a !live def
and b) setting/clearing the "persistent" flag, is that future patches
which change the details of network lifecycle management
(e.g. upcoming patches to fix detection of "active" networks when
libvirtd is restarted) will find it much more difficult to break
persistence functionality.
The networkCheckRouteCollision, networkAddFirewallRules and
networkRemoveFirewallRules APIs all take a virNetworkObjPtr
instance, but only ever access the 'def' member. It thus
simplifies testing if the APIs are changed to just take a
virNetworkDefPtr instead
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Since it is an abbreviation, PCI should always be fully
capitalized or full lower case, never Pci.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
A patch submitted by Steven Malin last week pointed out a problem with
libvirt's DNS SRV record configuration:
https://www.redhat.com/archives/libvir-list/2014-March/msg00536.html
When searching for that message later, I found another series that had
been posted by Guannan Ren back in 2012 that somehow slipped between
the cracks:
https://www.redhat.com/archives/libvir-list/2012-July/msg00236.html
That patch was very much out of date, but also pointed out some real
problems.
This patch fixes all the noted problems by refactoring
virNetworkDNSSrvDefParseXML() and networkDnsmasqConfContents(), then
verifies those fixes by added several new records to the test case.
Problems fixed:
* both service and protocol now have an underscore ("_") prepended on
the commandline, as required by RFC2782.
<srv service='sip' protocol='udp' domain='example.com'
target='tests.example.com' port='5060' priority='10'
weight='150'/>
before: srv-host=sip.udp.example.com,tests.example.com,5060,10,150
after: srv-host=_sip._udp.example.com,tests.example.com,5060,10,150
* if "domain" wasn't specified in the <srv> element, the extra
trailing "." will no longer be added to the dnsmasq commandline.
<srv service='sip' protocol='udp' target='tests.example.com'
port='5060' priority='10' weight='150'/>
before: srv-host=sip.udp.,tests.example.com,5060,10,150
after: srv-host=_sip._udp,tests.example.com,5060,10,150
* when optional attributes aren't specified, the separating comma is
also now not placed on the dnsmasq commandline. If optional
attributes in the middle of the line are not specified, they are
replaced with a default value in the commandline (1 for port, 0 for
priority and weight).
<srv service='sip' protocol='udp' target='tests.example.com'
port='5060'/>
before: srv-host=sip.udp.,tests.example.com,5060,,
after: srv-host=_sip._udp,tests.example.com,5060
(actually the would have generated an error, because "optional"
attributes weren't really optional.)
* The allowed characters for both service and protocol are now limited
to alphanumerics, plus a few special characters that are found in
existing names in /etc/services and /etc/protocols. (One exception
is that both of these files contain names with an embedded ".", but
"." can't be used in these fields of an SRV record because it is
used as a field separator and there is no method to escape a "."
into a field.) (Previously only the strings "tcp" and "udp" were
allowed for protocol, but this restriction has been removed, since
RFC2782 specifically says that it isn't limited to those, and that
anyway it is case insensitive.)
* the "domain" attribute is no longer required in order to recognize
the port, priority, and weight attributes during parsing. Only
"target" is required for this.
* if "target" isn't specified, port, priority, and weight are not
allowed (since they are meaningless - an empty target means "this
service is *not available* for this domain").
* port, priority, and weight are now truly optional, as the comments
originally suggested, but which was not actually true.
Any source file which calls the logging APIs now needs
to have a VIR_LOG_INIT("source.name") declaration at
the start of the file. This provides a static variable
of the virLogSource type.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Coverity found an issue in lxc_driver and uml_driver that we don't
check the return value of register functions.
I've also updated all other places and unify the way we check the
return value.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
According to commit b4e0299d if networkAllocateActualDevice() was
successful, it will *always* allocate an iface->data.network.actual,
so we can use this during networkReleaseActualDevice() to know if
there is really anything to undo. We were properly using this
information to only decrement the network connections counter if it
had previously been incremented, but we were unconditionally
unplugging bandwidth and calling the "unplugged" network hook for
*all* interfaces (during qemuProcessStop()) whether they had been
previously plugged or not. This caused problems if a domain failed to
start at some time prior to all interfaces being allocated. (I
encountered this when an interface had a bandwidth floor set but no
inbound QoS).
This patch changes both the call to networkUnplugBandwidth() and the
call to networkRunHook() to only be called if there was a previous
call to "plug" for the same interface.
networkAllocateActualDevice() is called for *all* interfaces, not just
those with type='network'. In that case, it will jump down to its
validate: label immediately, without allocating anything. After
validation is done, two counters are potentially updated (one for the
network, and one for any particular physical device that is chosen),
and then networkRunHook() is called.
This patch refactors that code a slight bit so that networkRunHook()
doesn't get called if netdef is NULL (i.e. type != network) and to
place the conditional increment of dev->connections inside the "if
(netdef)" as well - dev can never be non-null if netdef is null
(because "dev" is the pointer to a device in a network's pool of
devices), so this doesn't have any functional effect, it just makes
the code clearer.
The network hook script gets called whenever an interface is plugged
into or unplugged from a network, but even though the full XML of both
the network and the domain is included, there is no reasonable way to
determine what exact resources the plugged interface is using:
1) Prior to a recent patch which modified the status XML of interfaces
to include the information about actual hardware resources used, it
would be possible to scan through the domain XML output sent to the
hook, and from there find the correct interface, but that interface
definition would not include any runtime info (e.g. bandwidth or vlan
taken from a portgroup, or which physdev was used in case of a macvtap
network).
2) After the patch modifying the status XML of interfaces, the network
name would no longer be included in the domain XML, so it would be
completely impossible to determine which interface was the one being
plugged.
To solve that problem, this patch includes a single <interface>
element at the beginning of the XML sent to the network hook for
"plugged" and "unplugged" (just inside <hookData>) that is the status
XML of the interface being plugged. This XML will include all info
gathered from the chosen network and portgroup.
NB: due to hardcoded spaces in all of the device *Format() functions,
the <interface> element inside the <hookData> will be indented by 6
spaces rather than 2. I had intended to fix this, but it turns out
that to make virDomainNetDefFormat() indentation relative, I would
have to do the same to virDomainDeviceInfoFormat(), and that function
is called from 19 places - making that a prerequisite of this patch
would cause too many merge difficulties if we needed to backport
network hooks, so I chose to ignore the problem here and fix the
problem for *all* devices in a followup later.
Currently, networkRunHook() is called in networkAllocateActualDevice and
friends. These functions, however, doesn't necessarily work on networks,
For example, if domain's interface is defined in this fashion:
<interface type='bridge'>
<mac address='52:54:00:0b:3b:16'/>
<source bridge='virbr1'/>
<model type='rtl8139'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x09' function='0x0'/>
</interface>
The networkAllocateActualDevice jumps directly onto 'validate' label as
the interface is not type of 'network'. Hence, @network is left
initialized to NULL and networkRunHook(network, ...) is called. One of
the things that the hook function does is dereference @network. Soupir.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Basically, the idea is copied from domain code, where tainting
exists for a while. Currently, only one taint reason exists -
VIR_NETWORK_TAINT_HOOK to mark those networks which caused invoking
of hook script.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There might be some use cases, where user wants to prepare the host or
its environment prior to starting a network and do some cleanup after
the network has been shut down. Consider all the functionality that
libvirt doesn't currently have as an example what a hook script can
possibly do.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The lack of debug printings might be frustrating in the future.
Moreover, this function doesn't follow the usual pattern we have in the
rest of the code:
int ret = -1;
/* do some work */
ret = 0;
cleanup:
/* some cleanup work */
return ret;
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1058839
Commit f9f56340 for CVE-2014-0028 almost had the right idea - we
need to check the ACL rules to filter which events to send. But
it overlooked one thing: the event dispatch queue is running in
the main loop thread, and therefore does not normally have a
current virIdentityPtr. But filter checks can be based on current
identity, so when libvirtd.conf contains access_drivers=["polkit"],
we ended up rejecting access for EVERY event due to failure to
look up the current identity, even if it should have been allowed.
Furthermore, even for events that are triggered by API calls, it
is important to remember that the point of events is that they can
be copied across multiple connections, which may have separate
identities and permissions. So even if events were dispatched
from a context where we have an identity, we must change to the
correct identity of the connection that will be receiving the
event, rather than basing a decision on the context that triggered
the event, when deciding whether to filter an event to a
particular connection.
If there were an easy way to get from virConnectPtr to the
appropriate virIdentityPtr, then object_event.c could adjust the
identity prior to checking whether to dispatch an event. But
setting up that back-reference is a bit invasive. Instead, it
is easier to delay the filtering check until lower down the
stack, at the point where we have direct access to the RPC
client object that owns an identity. As such, this patch ends
up reverting a large portion of the framework of commit f9f56340.
We also have to teach 'make check' to special-case the fact that
the event registration filtering is done at the point of dispatch,
rather than the point of registration. Note that even though we
don't actually use virConnectDomainEventRegisterCheckACL (because
the RegisterAny variant is sufficient), we still generate the
function for the purposes of documenting that the filtering
takes place.
Also note that I did not entirely delete the notion of a filter
from object_event.c; I still plan on using that for my upcoming
patch series for qemu monitor events in libvirt-qemu.so. In
other words, while this patch changes ACL filtering to live in
remote.c and therefore we have no current client of the filtering
in object_event.c, the notion of filtering in object_event.c is
still useful down the road.
* src/check-aclrules.pl: Exempt event registration from having to
pass checkACL filter down call stack.
* daemon/remote.c (remoteRelayDomainEventCheckACL)
(remoteRelayNetworkEventCheckACL): New functions.
(remoteRelay*Event*): Use new functions.
* src/conf/domain_event.h (virDomainEventStateRegister)
(virDomainEventStateRegisterID): Drop unused parameter.
* src/conf/network_event.h (virNetworkEventStateRegisterID):
Likewise.
* src/conf/domain_event.c (virDomainEventFilter): Delete unused
function.
* src/conf/network_event.c (virNetworkEventFilter): Likewise.
* src/libxl/libxl_driver.c: Adjust caller.
* src/lxc/lxc_driver.c: Likewise.
* src/network/bridge_driver.c: Likewise.
* src/qemu/qemu_driver.c: Likewise.
* src/remote/remote_driver.c: Likewise.
* src/test/test_driver.c: Likewise.
* src/uml/uml_driver.c: Likewise.
* src/vbox/vbox_tmpl.c: Likewise.
* src/xen/xen_driver.c: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1057321
pointed out that we weren't honoring the <bandwidth> element in
libvirt networks using <forward mode='bridge'/>. In fact, these
networks are just a method of giving a libvirt network name to an
existing Linux host bridge on the system, and libvirt doesn't have
enough information to know where to set such limits. We are working on
a method of supporting network bandwidths for some specific cases of
<forward mode='bridge'/>, but currently libvirt doesn't support it. So
the proper thing to do now is just log an error when someone tries to
put a <bandwidth> element in that type of network. (It's unclear if we
will be able to do proper bandwidth limiting for macvtap networks, and
most definitely we will not be able to support it for hostdev
networks).
While looking through the network XML documentation and comparing it
to the networkValidate function, I noticed that we also ignore the
presence of a mac address in the config in the same cases, rather than
failing so that the user will understand that their desired action has
not been taken.
This patch updates networkValidate() (which is called any time a
persistent network is defined, or a transient network created) to log
an error and fail if it finds either a <bandwidth> or <mac> element
and the network forward mode is anything except 'route'. 'nat', or
nothing. (Yes, neither of those elements is acceptable for any macvtap
mode, nor for a hostdev network).
NB: This does *not* cause failure to start any existing network that
contains one of those elements, so someone might have erroneously
defined such a network in the past, and that network will continue to
function unmodified. I considered it too disruptive to suddenly break
working configs on the next reboot after a libvirt upgrade.
The previous patch fixed "forwardPlainNames" so that it really is
doing only what is intended, but left the default to be
"forwardPlainNames='no'". Discussion around the initial version of
that patch led to the decision that the default should instead be
"forwardPlainNames='yes'" (i.e. the original behavior before commit
f3886825). This patch makes that change to the default.
In commit f386825 we began adding the options
--domain-needed
--local=/$mydomain/
to all dnsmasq commandlines with the stated reason of preventing
forwarding of DNS queries for names that weren't fully qualified
domain names ("FQDN", i.e. a name that included some "."s and a domain
name). This was later changed to
domain-needed
local=/$mydomain/
when we moved the options from the dnsmasq commandline to a conf file.
The original patch on the list, and discussion about it, is here:
https://www.redhat.com/archives/libvir-list/2012-August/msg01594.html
When a domain name isn't specified (mydomain == ""), the addition of
"domain-needed local=//" will prevent forwarding of domain-less
requests to the virtualization host's DNS resolver, but if a domain
*is* specified, the addition of "local=/domain/" will prevent
forwarding of any requests for *qualified* names within that domain
that aren't resolvable by libvirt's dnsmasq itself.
An example of the problems this causes - let's say a network is
defined with:
<domain name='example.com'/>
<dhcp>
..
<host mac='52:54:00:11:22:33' ip='1.2.3.4' name='myguest'/>
</dhcp>
This results in "local=/example.com/" being added to the dnsmasq options.
If a guest requests "myguest" or "myguest.example.com", that will be
resolved by dnsmasq. If the guest asks for "www.example.com", dnsmasq
will not know the answer, but instead of forwarding it to the host, it
will return NOT FOUND to the guest. In most cases that isn't the
behavior an admin is looking for.
A later patch (commit 4f595ba) attempted to remedy this by adding a
"forwardPlainNames" attribute to the <dns> element. The idea was that
if forwardPlainNames='yes' (default is 'no'), we would allow
unresolved names to be forwarded. However, that patch was botched, in
that it only removed the "domain-needed" option when
forwardPlainNames='yes', and left the "local=/mydomain/".
Really we should have been just including the option "--domain-needed
--local=//" (note the lack of domain name) regardless of the
configured domain of the network, so that requests for names without a
domain would be treated as "local to dnsmasq" and not forwarded, but
all others (including those in the network's configured domain) would
be forwarded. We also shouldn't include *either* of those options if
forwardPlainNames='yes'. This patch makes those corrections.
This patch doesn't remedy the fact that default behavior was changed
by the addition of this feature. That will be handled in a subsequent
patch.
This reverts commit 2996e6be19
and some parts of 2636dc8c4d.
The former one tried to implement QoS setting on bridgeless networks.
However, as discussed upstream [1], the patch is far away from being
useful in even a single case. The whole idea of network QoS is to have
aggregated limits over several interfaces. This patch is doing
completely the opposite when merging two QoS settings (from the network
and the domain interface) into one which is then set at the domain
interface itself, not the network.
The latter one is the test for the previous one. Now none of them makes
sense.
1: https://www.redhat.com/archives/libvir-list/2014-January/msg01441.html
Conflicts:
tests/virnetdevbandwidthtest.c: New test has been introduced since
then.
https://bugzilla.redhat.com/show_bug.cgi?id=1055484
Currently, libvirt's XML schema of network allows QoS to be defined for
every network even though it has no bridge. For instance:
<network>
<name>vdsm-no-bridge</name>
<forward mode='passthrough'>
<interface dev='em1.10'/>
</forward>
<bandwidth>
<inbound average='1000' peak='5000' burst='1024'/>
<outbound average='1000' burst='1024'/>
</bandwidth>
</network>
The bandwidth limitations can be, however, applied even on such
networks. In fact, they are going to be applied on the interface that
will be connected to the network on a domain startup. This approach,
however, has one limitation. With bridged networks, there are two points
where QoS can be set: bridge and domain interface. The lower limit of
the two is enforced then. For instance, if the interface has 10Mbps
average, but the network only 1Mbps, there's no way for interface to
transmit packets faster than the 1Mbps limit. With two points this is
enforced by kernel. With only one point, we must combine both QoS
settings into one which is set afterwards. Look at
virNetDevBandwidthMinimal() and you'll understand immediately what I
mean.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Ever since ACL filtering was added in commit 7639736 (v1.1.1), a
user could still use event registration to obtain access to a
domain that they could not normally access via virDomainLookup*
or virConnectListAllDomains and friends. We already have the
framework in the RPC generator for creating the filter, and
previous cleanup patches got us to the point that we can now
wire the filter through the entire object event stack.
Furthermore, whether or not domain:getattr is honored, use of
global events is a form of obtaining a list of networks, which
is covered by connect:search_domains added in a93cd08 (v1.1.0).
Ideally, we'd have a way to enforce connect:search_domains when
doing global registrations while omitting that check on a
per-domain registration. But this patch just unconditionally
requires connect:search_domains, even when no list could be
obtained, based on the following observations:
1. Administrators are unlikely to grant domain:getattr for one
or all domains while still denying connect:search_domains - a
user that is able to manage domains will want to be able to
manage them efficiently, but efficient management includes being
able to list the domains they can access. The idea of denying
connect:search_domains while still granting access to individual
domains is therefore not adding any real security, but just
serves as a layer of obscurity to annoy the end user.
2. In the current implementation, domain events are filtered
on the client; the server has no idea if a domain filter was
requested, and must therefore assume that all domain event
requests are global. Even if we fix the RPC protocol to
allow for server-side filtering for newer client/server combos,
making the connect:serach_domains ACL check conditional on
whether the domain argument was NULL won't benefit older clients.
Therefore, we choose to document that connect:search_domains
is a pre-requisite to any domain event management.
Network events need the same treatment, with the obvious
change of using connect:search_networks and network:getattr.
* src/access/viraccessperm.h
(VIR_ACCESS_PERM_CONNECT_SEARCH_DOMAINS)
(VIR_ACCESS_PERM_CONNECT_SEARCH_NETWORKS): Document additional
effect of the permission.
* src/conf/domain_event.h (virDomainEventStateRegister)
(virDomainEventStateRegisterID): Add new parameter.
* src/conf/network_event.h (virNetworkEventStateRegisterID):
Likewise.
* src/conf/object_event_private.h (virObjectEventStateRegisterID):
Likewise.
* src/conf/object_event.c (_virObjectEventCallback): Track a filter.
(virObjectEventDispatchMatchCallback): Use filter.
(virObjectEventCallbackListAddID): Register filter.
* src/conf/domain_event.c (virDomainEventFilter): New function.
(virDomainEventStateRegister, virDomainEventStateRegisterID):
Adjust callers.
* src/conf/network_event.c (virNetworkEventFilter): New function.
(virNetworkEventStateRegisterID): Adjust caller.
* src/remote/remote_protocol.x
(REMOTE_PROC_CONNECT_DOMAIN_EVENT_REGISTER)
(REMOTE_PROC_CONNECT_DOMAIN_EVENT_REGISTER_ANY)
(REMOTE_PROC_CONNECT_NETWORK_EVENT_REGISTER_ANY): Generate a
filter, and require connect:search_domains instead of weaker
connect:read.
* src/test/test_driver.c (testConnectDomainEventRegister)
(testConnectDomainEventRegisterAny)
(testConnectNetworkEventRegisterAny): Update callers.
* src/remote/remote_driver.c (remoteConnectDomainEventRegister)
(remoteConnectDomainEventRegisterAny): Likewise.
* src/xen/xen_driver.c (xenUnifiedConnectDomainEventRegister)
(xenUnifiedConnectDomainEventRegisterAny): Likewise.
* src/vbox/vbox_tmpl.c (vboxDomainGetXMLDesc): Likewise.
* src/libxl/libxl_driver.c (libxlConnectDomainEventRegister)
(libxlConnectDomainEventRegisterAny): Likewise.
* src/qemu/qemu_driver.c (qemuConnectDomainEventRegister)
(qemuConnectDomainEventRegisterAny): Likewise.
* src/uml/uml_driver.c (umlConnectDomainEventRegister)
(umlConnectDomainEventRegisterAny): Likewise.
* src/network/bridge_driver.c
(networkConnectNetworkEventRegisterAny): Likewise.
* src/lxc/lxc_driver.c (lxcConnectDomainEventRegister)
(lxcConnectDomainEventRegisterAny): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
While comparing network and domain events, I noticed that the
test driver had to do a cast in one place and not the other.
For consistency, we should hide the necessary casting as low
as possible in the stack, with everything else using saner
types.
* src/conf/network_event.h (virNetworkEventStateRegisterID): Alter
type.
* src/conf/network_event.c (virNetworkEventStateRegisterID): Hoist
cast here.
* src/test/test_driver.c (testConnectNetworkEventRegisterAny):
Simplify callers.
* src/remote/remote_driver.c
(remoteConnectNetworkEventRegisterAny): Likewise.
* src/network/bridge_driver.c
(networkConnectNetworkEventRegisterAny): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Ever since their introduction (commit 1509b80 in v0.5.0 for
virConnectDomainEventRegister, commit 4445723 in v0.8.0 for
virConnectDomainEventDeregisterAny), the event deregistration
functions have been documented as returning 0 on success;
likewise for older registration (only the newer RegisterAny
must return a non-zero callbackID). And now that we are
adding virConnectNetworkEventDeregisterAny for v1.2.1, it
should have the same semantics.
Fortunately, all of the stateful drivers have been obeying
the docs and returning 0, thanks to the way the remote_driver
tracks things (in fact, the RPC wire protocol is unable to
send a return value for DomainEventRegisterAny, at least not
without adding a new RPC number). Well, except for vbox,
which was always failing deregistration, due to failure to
set the return value to anything besides its initial -1.
But for local drivers, such as test:///default, we've been
returning non-zero numbers; worse, the non-zero numbers have
differed over time. For example, in Fedora 12 (libvirt 0.8.2),
calling Register twice would return 0 and 1 [the callbackID
generated under the hood]; while in Fedora 20 (libvirt 1.1.3),
it returns 1 and 2 [the number of callbacks registered for
that event type]. Since we have changed the behavior over
time, and since it differs by local vs. remote, we can safely
argue that no one could have been reasonably relying on any
particular behavior, so we might as well obey the docs, as well
as prepare callers that might deal with older clients to not be
surprised if the docs are not strictly followed.
For consistency, this patch fixes the code for all drivers,
even though it only makes an impact for vbox and for local
drivers. By fixing all drivers, future copy and paste from
a remote driver to a local driver is less likely to
reintroduce the bug.
Finally, update the testsuite to gain some coverage of the
issue for local drivers, including the first test of old-style
domain event registration via function pointer instead of
event id.
* src/libvirt.c (virConnectDomainEventRegister)
(virConnectDomainEventDeregister)
(virConnectDomainEventDeregisterAny): Clarify docs.
* src/libxl/libxl_driver.c (libxlConnectDomainEventRegister)
(libxlConnectDomainEventDeregister)
(libxlConnectDomainEventDeregisterAny): Match documentation.
* src/lxc/lxc_driver.c (lxcConnectDomainEventRegister)
(lxcConnectDomainEventDeregister)
(lxcConnectDomainEventDeregisterAny): Likewise.
* src/test/test_driver.c (testConnectDomainEventRegister)
(testConnectDomainEventDeregister)
(testConnectDomainEventDeregisterAny)
(testConnectNetworkEventDeregisterAny): Likewise.
* src/uml/uml_driver.c (umlConnectDomainEventRegister)
(umlConnectDomainEventDeregister)
(umlConnectDomainEventDeregisterAny): Likewise.
* src/vbox/vbox_tmpl.c (vboxConnectDomainEventRegister)
(vboxConnectDomainEventDeregister)
(vboxConnectDomainEventDeregisterAny): Likewise.
* src/xen/xen_driver.c (xenUnifiedConnectDomainEventRegister)
(xenUnifiedConnectDomainEventDeregister)
(xenUnifiedConnectDomainEventDeregisterAny): Likewise.
* src/network/bridge_driver.c
(networkConnectNetworkEventDeregisterAny): Likewise.
* tests/objecteventtest.c (testDomainCreateXMLOld): New test.
(mymain): Run it.
(testDomainCreateXML): Check return values.
Signed-off-by: Eric Blake <eblake@redhat.com>
While the public API & wire protocol included the 'detail'
arg for network lifecycle events, the internal event handling
code did not process it. This meant that if a future libvirtd
server starts sending non-0 'detail' args, the current libvirt
client will not process them.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1035336
The basic problem is that during a network update, the required
iptables rules sometimes change, and this was being handled by simply
removing and re-adding the rules. However, the removal of the old
rules was done based on the *new* state of the network, which would
mean that some of the rules would not match those currently in the
system, so the old rules wouldn't be removed.
This patch removes the old rules prior to updating the network
definition then adds the new rules as soon as the definition is
updated. Note that this could lead to a stray packet or two during the
interim, but that was already a problem before (the period of limbo is
now just slightly longer).
While moving the location for the rules, I added a few more sections
that should result in the iptables rules being redone:
DHCP_RANGE and DHCP_HOST - these are needed because adding/removing a dhcp
host entry could lead to the dhcp service being started/stopped, which
would require that the mangle rule that fixes up dhcp response
checksums sould need to be added/removed, and this wasn't being done.
Most of our code base uses space after comma but not before;
fix the remaining uses before adding a syntax check.
* src/network/bridge_driver.c: Consistently use commas.
* src/node_device/node_device_hal.c: Likewise.
* src/node_device/node_device_udev.c: Likewise.
* src/storage/storage_backend_rbd.c: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1020135
If networkAllocateActualDevice() had failed due to a pool of hostdev
or direct devices being depleted, the calling function could still
call networkReleaseActualDevice() as part of its cleanup, and that
function would then unconditionally decrement the connections count
for the network, even though it hadn't been incremented (due to
failure of allocate). This *was* necessary because the .actual member
of the netdef was allocated with a "lazy" algorithm, only being
created if there was a need to store data there (e.g. if a device was
allocated from a pool, or bandwidth was allocated for the device), so
there was no simple way for networkReleaseActualDevice() to tell if
something really had been allocated (i.e. if "connections++" had been
executed).
This patch changes networkAllocateDevice() to *always* allocate an
actual device for any netdef of type='network', even if it isn't
needed for any other reason. This has no ill effects anywhere else in
the code (except for using a small amount of memory), and
networkReleaseActualDevice() can then determine if there was a
previous successful allocate by checking for .actual != NULL (if not,
it skips the "connections--").
Currently, we ignore whether dnsmasqCapsRefresh succeeds or fails. We
shouldn't do that as we may generate wrong dnsmasq command line (what
is done just a few lines below).
Signed-off-by: Hongwei Bi <hwbi2008@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Useful to set custom forwarders instead of using the contents of
/etc/resolv.conf. It helps me to setup dnsmasq as local nameserver to
resolve VM domain names from domain 0, when domain option is used.
Signed-off-by: Diego Woitasen <diego.woitasen@vhgroup.net>
Signed-off-by: Eric Blake <eblake@redhat.com>
Similarly to qemu_driver.c, we can join often repeating code of looking
up network into one function: networkObjFromNetwork.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This resolves the issue that prompted the filing of
https://bugzilla.redhat.com/show_bug.cgi?id=928638
(although the request there is for something much larger and more
general than this patch).
commit f3868259ca disabled the
forwarding to upstream DNS servers of unresolved DNS requests for
names that had no domain, but were just simple host names (no "."
character anywhere in the name). While this behavior is frowned upon
by DNS root servers (that's why it was changed in libvirt), it is
convenient in some cases, and since dnsmasq can be configured to allow
it, it must not be strictly forbidden.
This patch restores the old behavior, but since it is usually
undesirable, restoring it requires specification of a new option in
the network config. Adding the attribute "forwardPlainNames='yes'" to
the <dns> elemnt does the trick - when that attribute is added to a
network config, any simple hostnames that can't be resolved by the
network's dnsmasq instance will be forwarded to the DNS servers listed
in the host's /etc/resolv.conf for an attempt at resolution (just as
any FQDN would be forwarded).
When that attribute *isn't* specified, unresolved simple names will
*not* be forwarded to the upstream DNS server - this is the default
behavior.
* Move platform specific things (e.g. firewalling and route
collision checks) into bridge_driver_platform
* Create two platform specific implementations:
- bridge_driver_linux: Linux implementation using iptables,
it's actually the code moved from bridge_driver.c
- bridge_driver_nop: dumb implementation that does nothing
Signed-off-by: Eric Blake <eblake@redhat.com>
This is another cleanup before extracting platform-specific
parts from bridge_driver.
Rename struct network_driver to _virNetworkDriverState and
add appropriate typedefs: virNetworkDriverState and
virNetworkDriverStatePtr.
This will help us to avoid potential problems when moving
this struct to the .h file.
Convert the type of loop iterators named 'i', 'j', k',
'ii', 'jj', 'kk', to be 'size_t' instead of 'int' or
'unsigned int', also santizing 'ii', 'jj', 'kk' to use
the normal 'i', 'j', 'k' naming
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
iptablesContext holds only 4 pairs of iptables
(table, chain) and there's no need to pass
it around.
This is a first step towards separating bridge_driver.c
in platform-specific parts.
If networkUnplugBandwidth is called on a network which has
no bandwidth defined, print a warning instead of crashing.
This can happen when destroying a domain with bandwidth if
bandwidth was removed from the network after the domain was
started.
https://bugzilla.redhat.com/show_bug.cgi?id=975359
Although SRIOV network cards support setting a vlan tag on their
virtual functions, and although setting this vlan tag via a <vlan>
element in a domain's <interface> works, setting a vlan tag for these
devices in a <network> definition, or in a network <portgroup>
definition is also supposed to work (and the comment that validates
<vlan> usage even says that!). However, the check to allow it only
checked for an openvswitch network, so attempts to add <vlan> to a
network of type='hostdev' would fail.
This fixes the problem reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=972690
When checking for a collision of a new libvirt network's subnet with
any existing routes, we read all of /proc/net/route into memory, then
parse all the entries. The function that we use to read this file
requires a "maximum length" parameter, which had previously been set
to 64*1024. As each line in /proc/net/route is 128 bytes, this would
allow for a maximum of 512 entries in the routing table.
This patch increases that number to 128 * 100000, which allows for
100,000 routing table entries. This means that it's possible that 12MB
would be allocated, but that would only happen if there really were
100,000 route table entries on the system, it's only held for a very
short time.
Since there is no method of specifying and unlimited max (and that
would create a potential denial of service anyway) hopefully this
limit is large enough to accomodate everyone.
In order to learn libvirt multiqueue several things must be done:
1) The '/dev/net/tun' device needs to be opened multiple times with
IFF_MULTI_QUEUE flag passed to ioctl(fd, TUNSETIFF, &ifr);
2) Similarly, '/dev/vhost-net' must be opened as many times as in 1)
in order to keep 1:1 ratio recommended by qemu and kernel folks.
3) The command line construction code needs to switch from 'fd=X' to
'fds=X:Y:...:Z' and from 'vhostfd=X' to 'vhostfds=X:Y:...:Z'.
4) The monitor handling code needs to learn to pass multiple FDs.
network: static route support for <network>
This patch adds the <route> subelement of <network> to define a static
route. the address and prefix (or netmask) attribute identify the
destination network, and the gateway attribute specifies the next hop
address (which must be directly reachable from the containing
<network>) which is to receive the packets destined for
"address/(prefix|netmask)".
These attributes are translated into an "ip route add" command that is
executed when the network is started. The command used is of the
following form:
ip route add <address>/<prefix> via <gateway> \
dev <virbr-bridge> proto static metric <metric>
Tests are done to validate that the input data are correct. For
example, for a static route ip definition, the address must be a
network address and not a host address. Additional checks are added
to ensure that the specified gateway is directly reachable via this
network (i.e. that the gateway IP address is in the same subnet as one
of the IP's defined for the network).
prefix='0' is supported for both family='ipv4' address='0.0.0.0'
netmask='0.0.0.0' or prefix='0', and for family='ipv6' address='::',
prefix=0', although care should be taken to not override a desired
system default route.
Anytime an attempt is made to define a static route which *exactly*
duplicates an existing static route (for example, address=::,
prefix=0, metric=1), the following error message will be sent to
syslog:
RTNETLINK answers: File exists
This can be overridden by decreasing the metric value for the route
that should be preferred, or increasing the metric for the route that
shouldn't be preferred (and is thus in place only in anticipation that
the preferred route may be removed in the future). Caution should be
used when manipulating route metrics, especially for a default route.
Note: The use of the command-line interface should be replaced by
direct use of libnl so that error conditions can be handled better. But,
that is being left as an exercise for another day.
Signed-off-by: Gene Czarcinski <gene@czarc.net>
Signed-off-by: Laine Stump <laine@laine.org>
This should resolve https://bugzilla.redhat.com/show_bug.cgi?id=958907
Recent new addition of code to read/write active network state to the
NETWORK_STATE_DIR in the network driver broke startup for
qemu:///session. The network driver had several state file paths
hardcoded to /var, which could never possibly work in session mode.
This patch modifies *all* state files to use a variable string that is
set differently according to whether or not we're running
privileged. (It turns out that logDir was never used, so it's been
completely eliminated.)
There are very definitely other problems preventing dnsmasq and radvd
from running in non-privileged mode, but it's more consistent to have
the directories used by them be determined in the same fashion.
NB: I've noted before that the network driver is storing its state
(including dnsmasq and radvd state) in /var/lib, while qemu stores its
state in /var/run. It would probably have been better if the two
matched, but it's been this way for a long time, and changing it would
break running installations during an upgrade, so it's best to just
leave it as it is.
The call to virReportError conditionally switched between
two format strings, with different numbers of placeholders.
This meant the format string with no placeholders was not
protected by a "%s".
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The source code base needs to be adapted as well. Some files
include virutil.h just for the string related functions (here,
the include is substituted to match the new file), some include
virutil.h without any need (here, the include is removed), and
some require both.
On the off-chance that creation of persistent configuration file would
fail when defining a network that is already started as transient, the
code would remove the transient data structure and thus the network.
This patch changes the code so that in such case, the network is again
marked as transient and left behind.
This isn't strictly speaking a bugfix, but I realized I'd gotten a bit
too verbose when I chose the names for
VIR_DOMAIN_HOSTDEV_PCI_BACKEND_TYPE_*. This shortens them all a bit.
I remembered to document this bit, but somehow forgot to implement it.
This adds <driver name='kvm|vfio'/> as a subelement to the <forward>
element of a network (this puts it parallel to the match between
mode='hostdev' attribute in a network and type='hostdev' in an
<interface>).
Since it's already documented, only the parser, formatter, backend
driver recognition (it just translates/moves the flag into the
<interface> at the appropriate time), and a test case were needed.
(I used a separate enum for the values both because the original is
defined in domain_conf.h, which is unavailable from network_conf.h,
and because in the future it's possible that we may want to support
other non-hostdev oriented driver names in the network parser; this
makes sure that one can be expanded without the other).
There will soon be other items related to pci hostdevs that need to be
in the same part of the hostdevsubsys union as the pci address (which
is currently a single member called "pci". This patch replaces the
single member named pci with a struct named pci that contains a single
member named "addr".
Ensure that all drivers implementing public APIs use a
naming convention for their implementation that matches
the public API name.
eg for the public API virDomainCreate make sure QEMU
uses qemuDomainCreate and not qemuDomainStart
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
It will simplify later work if the sub-drivers have dedicated
APIs / field names. ie virNetworkDriver should have
virDrvNetworkOpen and virDrvNetworkClose methods
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Ensure that the driver struct field names match the public
API names. For an API virXXXX we must have a driver struct
field xXXXX. ie strip the leading 'vir' and lowercase any
leading uppercase letters.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Until now tranisent networks weren't really useful as libvirtd wasn't
able to remember them across restarts. This patch adds support for
loading status files of transient networks (that already were generated)
so that the status isn't lost.
This patch chops up virNetworkObjUpdateParseFile and turns it into
virNetworkLoadState and a few friends that will help us to load status
XMLs and refactors the functions that are loading the configs to use
them.
Detected by a simple Shell script:
for i in $(git ls-files -- '*.[ch]'); do
awk 'BEGIN {
fail=0
}
/# *include.*\.h/{
match($0, /["<][^">]*[">]/)
arr[substr($0, RSTART+1, RLENGTH-2)]++
}
END {
for (key in arr) {
if (arr[key] > 1) {
fail=1
printf("%d %s\n", arr[key], key)
}
}
if (fail == 1)
exit 1
}' $i
if test $? != 0; then
echo "Duplicate header(s) in $i"
fi
done;
A later patch will add the syntax-check to avoid duplicate
headers.
By current implementation, network inbound is required in order
to use 'floor' for guaranteeing minimal throughput. This is so,
because we want user to tell us the maximal throughput of the
network instead of finding out ourselves (and detect bogus values
in case of virtual interfaces). However, we are nowadays
requiring this only on documentation level. So if user starts a
domain with 'floor' set on one its interfaces, we silently ignore
the setting. We should error out instead.
This reverts commit 383ebc4694.
We decided the xml for this feature needed more thought to make sure
we are doing it the best way, in particular wrt option values that
have multiple items.
Originally, only a host name was used to associate a
DHCPv6 request with a specific IPv6 address. Further testing
demonstrates that this is an unreliable method and, instead,
a client-id or DUID needs to be used. According to DHCPv6
standards, this id can be a duid-LLT, duid-LL, or duid-UUID
even though dnsmasq will accept almost any text string.
Although validity checking of a specified string makes sure it is
hexadecimal notation with bytes separated by colons, there is no
rigorous check to make sure it meets the standard.
Documentation and schemas have been updated.
Signed-off-by: Gene Czarcinski <gene@czarc.net>
Signed-off-by: Laine Stump <laine@laine.org>
This patch adds support for a new <option>-Tag in the <dhcp> block of
network configs, based on a subset of the fifth proposal by Laine
Stump in the mailing list discussion at
https://www.redhat.com/archives/libvir-list/2012-November/msg01054.html.
Any such defined option will result in a dhcp-option=<number>,"<value>"
statement in the generated dnsmasq configuration file.
Currently, DHCP options can be specified by number only and there is
no whitelisting or blacklisting of option numbers, which should
probably be added.
Signed-off-by: Pieter Hollants <pieter@hollants.com>
Signed-off-by: Laine Stump <laine@laine.org>
We pass over the address/port start/end values many times so we put
them in structs.
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Laine Stump <laine@laine.org>
Let users set the port range to be used for forward mode NAT:
...
<forward mode='nat'>
<nat>
<port start='1024' end='65535'/>
</nat>
</forward>
...
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Laine Stump <laine@laine.org>
Support setting which public ip to use for NAT via attribute
address in subelement <nat> in <forward>:
...
<forward mode='nat'>
<address start='1.2.3.4' end='1.2.3.10'/>
</forward>
...
This will construct an iptables line using:
'-j SNAT --to-source <start>-<end>'
instead of:
'-j MASQUERADE'
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Laine Stump <laine@laine.org>
The conditional setting of cmdout in networkBuildDhcpDaemonCommandLine()
caused Coverity to complain that 'cmd' could be leaked if !cmdout. Since
the function is local and only called with cmdout being passed those checks
have been removed.
The fetch of 'ipdef' in networkRefreshDhcpDaemon() when the loop to fill
in ipv4def fails to find an ipv4 address with dhcp defined. The filled in
ipdef value was not used. Code was made unnecessary with commit it 2d5cd1.
The bandwidth plug and unplug functions were assuming that an
interface's bandwidth setting was always specified directly in the
domain's <interface> definition, but that's not necessarily true - it
could have been obtained from a <portgroup> definition in the network
definition. This patch fixes those functions to use
virDomainNetGetActualBandwidth(), which gets the bandwidth pointer
from iface->data.network.actual if it exists, otherwise returns
iface->bandwidth.
Remove extraneous check for 'netdef' when dereferencing for vlan.nTags.
Prior code would already check if netdef was NULL.
Coverity complained about a path where the 'vlan' was potentially valid,
but a prior checks may not have allocated 'iface->data.network.actual',
so like other paths it needs to be allocated on the fly.
Move the copying of vlan up earlier in networkAllocateActualDevice, so
that actual.type gets properly set.
Since the first assignment to vlan is redundant except in the case of
jumping immediately to validate from the start of the function,
eliminate its initial setting at the top of the function in favor of
calling the helper function virDomainNetGetActualVlan() (which doesn't
depend on the local vlan pointer being initialized) down at validate:
Signed-off-by: Laine Stump <laine@redhat.com>
If addition of rules in networkAddIptablesRules() failed the real error
was masked by error reported when trying to clean up the remaining
rules.
With this patch the original error message is saved and set back after
the removal is complete.
Commit 0211fd6e04 introduced regression
where newly defined networks were not made persistent.
This patch makes the network persistent on each successful definition.
This is yet another refinement to the fix for CVE-2012-3411:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
It turns out that it would be very intrusive to correctly backport the
entire --bind-dynamic option to older dnsmasq versions
(e.g. dnsmasq-2.48 that is used on RHEL6.x and CentOS 6.x), but very
simple to patch those versions to just use SO_BINDTODEVICE on all
their listening sockets (SO_BINDTODEVICE also has the desired effect
of permitting only traffic that was received on the interface(s) where
dnsmasq was set to listen.)
This patch modifies the dnsmasq capabilities detection to detect the
string:
--bind-interfaces with SO_BINDTODEVICE
in the output of "dnsmasq --version", and in that case realize that
using the old --bind-interfaces option is just as safe as
--bind-dynamic (and therefore *not* forbid creation of networks that
use public IP address ranges).
If -bind-dynamic is available, it is still preferred over
--bind-interfaces.
Note that this patch does no harm in upstream, or in any distro's
downstream if it happens to end up there, but builds for distros that
have a new enough dnsmasq to support --bind-dynamic do *NOT* need to
specifically backport this patch; it's only required for distro
releases that have dnsmasq too old to have --bind-dynamic (and those
distros will need to add the SO_BINDTODEVICE patch to dnsmasq,
*including the extra string in the --version output*, as well.
Somehow I managed to push the changes to this file with improper
indentation. This patch just re-indents, reformats the comment lines,
and re-groups a couple of multi-line strings so that they fit within
80 columns. The resulting binary should be identical.
A forgotten "!" in recently-modified code at the top of
networkRefreshDaemon() meant an improper early return, which led to 1)
dnsmasq config files not being updated from the newly modified config,
and 2) dnsmasq not being sent a SIGHUP so that it could learn about
the changes to the config.
virNetworkDefGetIpByIndex() returns NULL if there are no ip objects of
the requested type, and if there are no IP elements, then dnsmasq
shouldn't be running, so we can return early. Otherwise we should
rewrite the config files and send a SIGHUP.
This patch resolves the problem reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=886663
The source of the problem was the fix for CVE 2011-3411:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
which was originally committed upstream in commit
753ff83a50. That commit improperly
removed the "--except-interface lo" from dnsmasq commandlines when
--bind-dynamic was used (based on comments in the latter bug).
It turns out that the problem reported in the CVE could be eliminated
without removing "--except-interface lo", and removing it actually
caused each instance of dnsmasq to listen on localhost on port 53,
which created a new problem:
If another instance of dnsmasq using "bind-interfaces" (instead of
"bind-dynamic") had already been started (or if another instance
started later used "bind-dynamic"), this wouldn't have any immediately
visible ill effects, but if you tried to start another dnsmasq
instance using "bind-interfaces" *after* starting any libvirt
networks, the new dnsmasq would fail to start, because there was
already another process listening on port 53.
(Subsequent to the CVE fix, another patch changed the network driver
to put dnsmasq options in a conf file rather than directly on the
dnsmasq commandline, but preserved the same options.)
This patch changes the network driver to *always* add
"except-interface=lo" to dnsmasq conf files, regardless of whether we use
bind-dynamic or bind-interfaces. This way no libvirt dnsmasq instances
are listening on localhost (and the CVE is still fixed).
The actual code change is miniscule, but must be propogated through all
of the test files as well.
I noticed that /var/lib/libvirt/dnsmasq/*.conf used the wrong word;
it was intended to match the wording in src/util/xml.c.
* src/network/bridge_driver.c (networkDnsmasqConfContents): Fix typo.
* tests/networkxml2confdata/*.conf: Update accordingly.
Currently, we are only keeping a inactive XML configuration
in status dir. This is no longer enough as we need to keep
this class_id attribute so we don't overwrite old entries
when the daemon restarts. However, since there has already
been release which has just <network/> as root element,
and we want to keep things compatible, detect that loaded
status file is older one, and don't scream about it.
Network should be notified if we plug in or unplug an
interface, so it can perform some action, e.g. set/unset
network part of QoS. However, we are doing this in very
early stage, so iface->ifname isn't filled in yet. So
whenever we want to report an error, we must use a different
identifier, e.g. the MAC address.
These classes can borrow unused bandwidth. Basically,
only egress qdsics can have classes, therefore we can
do this kind of traffic shaping only on host's outgoing,
that is domain's incoming traffic.
This patch changes how parameters are passed to dnsmasq. Instead of
being on the command line, the parameters are put into a file (one
parameter per line) and a commandline --conf-file= specifies the
location of the file. The file is located in the same directory as
the leases file.
Putting the dnsmasq parameters into a configuration file
allows them to be examined and more easily understood than
examining the command lines displayed by "ps ax". This is
especially true when a number of networks have been started.
When the use of dnsmasq was originally done, the required command line
was simple, but it has gotten more complicated over time and will
likely become even more complicated in the future.
Note: The test conf files have all been renamed .conf instead of
.argv, and tests/networkxml2xmlargvdata was moved to
tests/networkxml2xmlconfdata.
The DHCPv6 support includes IPV6 dhcp-range and dhcp-host for one
IPv6 subnetwork on one interface. This support will only work
if dnsmasq version >= 2.64; otherwise an error occurs if
dhcp-range or dhcp-host is specified for an IPv6 address.
Essentially, this change provides the same DHCP support for IPv6
that has been available for IPv4.
With dnsmasq >= 2.64, support for the RA service is also now provided
by dnsmasq (radvd is no longer used/started). (Although at least one
version of dnsmasq prior to 2.64 "supported" IPv6 Router
Advertisement, there were bugs (fixed in 2.64) that rendered it
unusable.)
Documentation and the network schema has been updated
to reflect the new support.
The attributes of a <network> element's <forward> element were
previously stored directly in the virNetworkDef object, but
virNetworkUpdateForward() needs to operate on a <forward> in
isolation, so this patchs pulls out all those attributes into a
separate virNetworkForwardDef struct (and shortens their names
appropriately). This new object is contained in the virNetworkDef, not
pointed to by it, so there is no extra memory management.
This patch makes no functional changes, it only changes, e.g.,
"nForwardIfs" to "forward.nifs".
Since there is only a single virNetworkDNSDef for any virNetworkDef,
and it's trivial to determine whether or not it contains any real
data, it's much simpler (and fits more uniformly with the parse
function calling sequence of the parsers for many other objects that
are subordinates of virNetworkDef) if virNetworkDef *contains* an
virNetworkDNSDef rather than pointing to one.
Since it is now just a part of another object rather than its own
object, it no longer makes sense to have a *Free() function, so that
is changed to a *Clear() function.
More importantly though, ParseXML and Clear functions are needed for
the individual items contained in a virNetworkDNSDef (srv, txt, and
host records), but none of them have a *Clear(), and only two of the
three had *ParseXML() functions (both of which used a non-uniform
arglist). Those problems are cleared up by this patch - it splits the
higher-level Clear function into separate functions for each of the
three, creates a parse for txt records, and cleans up the srv and host
parsers, so we now have all the utility functions necessary to
implement virNetworkDefUpdateDNS(Host|Srv|Txt).
This shortens the name of the structs for srv and txt, and their
instances in virNetworkDNSDef, to be more compact and uniform with the
naming of the dns host array. It also changes the type of ntxts, etc
from unsigned int to size_t, so that they can be used directly as args
to VIR_*_ELEMENT.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=767057
It was possible to define a network with <forward mode='bridge'> that
had both a bridge device and a forward device defined. These two are
mutually exclusive by definition (if you are using a bridge device,
then this is a host bridge, and if you have a forward dev defined,
this is using macvtap). It was also possible to put <ip>, <dns>, and
<domain> elements in this definition, although those aren't supported
by the current driver (although it's conceivable that some other
driver might support that).
The items that are invalid by definition, are now checked in the XML
parser (since they will definitely *always* be wrong), and the others
are checked in networkValidate() in the network driver (since, as
mentioned, it's possible that some other network driver, or even this
one, could some day support setting those).
This patch adds the capability for virtual guests to do IPv6
communication via a virtual network interface with no IPv6 (gateway)
addresses specified. This capability has always been enabled by
default for IPv4, but disabled for IPv6 for security concerns, and
because it requires the ip6tables command to be operational (which
isn't the case on a system with the ipv6 module completely disabled).
This patch adds a new attribute "ipv6" at the toplevel of a <network>
object. If ipv6='yes', the extra ip6tables rules required to permite
inter-guest communications are added when the network is started. If
it is 'no', or not present, those rules will not be added; thus the
default behavior doesn't change, so there should be no compatibility
issues with any existing installations.
Note that virtual guests cannot communication with the virtualization
host via this interface, because the following kernel tunable has
been set:
net.ipv6.conf.<bridge_interface_name>.disable_ipv6 = 1
This assures that the bridge interface will not have an IPv6
link-local (fe80::) address.
To control this behavior so that it is not enabled by default, the parameter
ipv6='yes' on the <network> statement has been added.
Documentation related to this patch has been updated.
The network schema has also been updated.
Currently to deal with auto-shutdown libvirtd must periodically
poll all stateful drivers. Thus sucks because it requires
acquiring both the driver lock and locks on every single virtual
machine. Instead pass in a "inhibit" callback to virStateInitialize
which drivers can invoke whenever they want to inhibit shutdown
due to existance of active VMs.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The only important state that should prevent libvirtd shutdown
is from running VMs. Networks, host devices, network filters
and storage pools are all long lived resources that have no
significant in-memory state. They should not block shutdown.
This bug resolves CVE-2012-3411, which is described in the following
bugzilla report:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
The following report is specifically for libvirt on Fedora:
https://bugzilla.redhat.com/show_bug.cgi?id=874702
In short, a dnsmasq instance run with the intention of listening for
DHCP/DNS requests only on a libvirt virtual network (which is
constructed using a Linux host bridge) would also answer queries sent
from outside the virtualization host.
This patch takes advantage of a new dnsmasq option "--bind-dynamic",
which will cause the listening socket to be setup such that it will
only receive those requests that actually come in via the bridge
interface. In order for this behavior to actually occur, not only must
"--bind-interfaces" be replaced with "--bind-dynamic", but also all
"--listen-address" options must be replaced with a single
"--interface" option. Fully:
--bind-interfaces --except-interface lo --listen-address x.x.x.x ...
(with --listen-address possibly repeated) is replaced with:
--bind-dynamic --interface virbrX
Of course libvirt can't use this new option if the host's dnsmasq
doesn't have it, but we still want libvirt to function (because the
great majority of libvirt installations, which only have mode='nat'
networks using RFC1918 private address ranges (e.g. 192.168.122.0/24),
are immune to this vulnerability from anywhere beyond the local subnet
of the host), so we use the new dnsmasqCaps API to check if dnsmasq
supports the new option and, if not, we use the "old" option style
instead. In order to assure that this permissiveness doesn't lead to a
vulnerable system, we do check for non-private addresses in this case,
and refuse to start the network if both a) we are using the old-style
options, and b) the network has a publicly routable IP
address. Hopefully this will provide the proper balance of not being
disruptive to those not practically affected, and making sure that
those who *are* affected get their dnsmasq upgraded.
(--bind-dynamic was added to dnsmasq in upstream commit
54dd393f3938fc0c19088fbd319b95e37d81a2b0, which was included in
dnsmasq-2.63)
In order to optionally take advantage of new features in dnsmasq when
the host's version of dnsmasq supports them, but still be able to run
on hosts that don't support the new features, we need to be able to
detect the version of dnsmasq running on the host, and possibly
determine from the help output what options are in this dnsmasq.
This patch implements a greatly simplified version of the capabilities
code we already have for qemu. A dnsmasqCaps device can be created and
populated either from running a program on disk, reading a file with
the concatenated output of "dnsmasq --version; dnsmasq --help", or
examining a buffer in memory that contains the concatenated output of
those two commands. Simple functions to retrieve capabilities flags,
the version number, and the path of the binary are also included.
bridge_driver.c creates a single dnsmasqCaps object at driver startup,
and disposes of it at driver shutdown. Any time it must be used, the
dnsmasqCapsRefresh method is called - it checks the mtime of the
binary, and re-runs the checks if the binary has changed.
networkxml2argvtest.c creates 2 "artificial" dnsmasqCaps objects at
startup - one "restricted" (doesn't support --bind-dynamic) and one
"full" (does support --bind-dynamic). Some of the test cases use one
and some the other, to make sure both code pathes are tested.
The virStateInitialize method and several cgroups methods were
using an 'int privileged' parameter or similar for dual-state
values. These are better represented with the bool type.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The libvirt coding standard is to use 'function(...args...)'
instead of 'function (...args...)'. A non-trivial number of
places did not follow this rule and are fixed in this patch.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
When assigning the new persistent definition for a transient network
(thus making it persistent) the network needs to be marked persistent
before actually atempting to assign the definition.
Until now, the network undefine API was able to undefine only inactive
networks. The restriction doesn't make sense any more so this patch
implements changing networks to transient.
When a transient network was created some of the checks weren't run on
the definition allowing to start invalid networks.
This patch splits out code to the network validation function and
re-uses that code when creating transient networks.
The network driver didn't care about config files when a network was
destroyed, just when it was undefined leaving behind files for transient
networks.
This patch splits out the cleanup code to a helper function that handles
the cleanup if the inactive network object is being removed and re-uses
this code when getting rid of inactive networks.
The hosts file was created in the network definition function. This
patch moves the place the file is being created to the point where
dnsmasq is being started.
Three FORWARD chain rules are added and two INPUT chain rules
are added when a network is started but only the FORWARD chain
rules are removed when the network is destroyed.
This was found during testing of the fix for:
https://bugzilla.redhat.com/show_bug.cgi?id=868483
networkValidate was supposed to check for the existence of multiple
portgroups and report an error if this was encountered. It did, but
there were two problems:
1) even though it logged an error, it still returned success, allowing
the operation to continue.
2) It could exit the portgroup checking loop early (or possibly not
even do it once) if a vlan tag was supplied in the base network config
or one of the portgroups.
This patch fixes networkValidate to return failure in addition to
logging the error, and also changes it to not exit the portgroup
checking loop early. The logic was a bit off in the checking for vlan
anyway, and it's intertwined with fixing the early loop exit, so I
fixed that as well. Now it correctly checks for combinations where a
<virtualport> is specified in the base network def and <vlan> is given
in a portgroup, as well as the opposite (<vlan> in base network def
and <virtualport> in portgroup), and ignores the case of a disallowed
vlan when using *no* portgroup if there is a default portgroup (since
in that case there is no way to not use any portgroup).
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=868483
virNetworkUpdate, virNetworkDefine, and virNetworkCreate all three
allow network definitions to contain multiple <portgroup> elements
with default='yes'. Only a single default portgroup should be allowed
for each network.
This patch updates networkValidate() (called by both
virNetworkCreate() and virNetworkDefine()) and
virNetworkDefUpdatePortGroup (called by virNetworkUpdate() to not
allow multiple default portgroups.
This fixes the problem reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=868389
Previously, the dnsmasq hosts file (used for static dhcp entries, and
addnhosts file (used for additional dns host entries) were only
created/referenced on the dnsmasq commandline if there was something
to put in them at the time the network was started. Once we can update
a network definition while it's active (which is now possible with
virNetworkUpdate), this is no longer a valid strategy - if there were
0 dhcp static hosts (resulting in no reference to the hosts file on the
commandline), then one was later added, the commandline wouldn't have
linked dnsmasq up to the file, so even though we create it, dnsmasq
doesn't pay any attention.
The solution is to just always create these files and reference them
on the dnsmasq commandline (almost always, anyway). That way dnsmasq
can notice when a new entry is added at runtime (a SIGHUP is sent to
dnsmasq by virNetworkUdpate whenever a host entry is added or removed)
The exception to this is that the dhcp static hosts file isn't created
if there are no lease ranges *and* no static hosts. This is because in
this case dnsmasq won't be setup to listen for dhcp requests anyway -
in that case, if the count of dhcp hosts goes from 0 to 1, dnsmasq
will need to be restarted anyway (to get it listening on the dhcp
port). Likewise, if the dhcp hosts count goes from 1 to 0 (and there
are no dhcp ranges) we need to restart dnsmasq so that it will stop
listening on port 67. These special situations are handled in the
bridge driver's networkUpdate() by checking for ((bool)
nranges||nhosts) both before and after the update, and triggering a
dnsmasq restart if the before and after don't match.
https://bugzilla.redhat.com/show_bug.cgi?id=866364
pointed out a crash due to virNetworkObjAssignDef free'ing
network->newDef without NULLing it afterward. A fix for this is in
upstream commit b7e9202401. While the
NULLing of newDef was a legitimate fix, newDef should have already
been empty (NULL) anyway (as indicated in the comment that was deleted
by that commit).
The reason that newDef had a non-NULL value (i.e. the root cause) was
that networkStartNetwork() had failed after populating
network->newDef, but then neglected to free/NULL newDef in the
cleanup.
(A bit of background here: network->newDef should contain the
persistent config of a network when a network is active (and of course
only when it is persisten), and NULL at all other times. There is also
a network->def which should contain the persistent definition of the
network when it is inactive, and the current live state at all other
times. The idea is that you can make changes to network->newDef which
will take effect the next time the network is restarted, but won't
mess with the current state of the network (virDomainObj has a similar
pair of virDomainDefs that behave in the same fashion). Personally I
think there should be a network->live and network->config, and the
location of the persistent config should *always* be in
network->config, but that's for a later cleanup).
Since I love things to be symmetric, I created a new function called
virNetworkObjUnsetDefTransient(), which reverses the effects of
virNetworkObjSetDefTransient(). I don't really like the name of the
new function, but then I also didn't really like the name of the old
one either (it's just named that way to match a similar function in
the domain conf code).
This function really should have been taking virDevicePCIAddress*
instead of the inefficient virDevicePCIAddress (results in copying two
entire structs onto the stack rather than just two pointers), and
returning a bool true/false (not matching is not necessarily a
"failure", as a -1 return would imply, and also using "if
(!virDevicePCIAddressEqual(x, y))" to mean "if x == y" is just a bit
counterintuitive).
I hit this problem recently when trying to create a bridge with an IPv6
address on a 3.2 kernel: dnsmasq (and, further, radvd) would not bind to
the given address, waiting 20s and then giving up with -EADDRNOTAVAIL
(resp. exiting immediately with "error parsing or activating the config
file", without libvirt noticing it, BTW). This can be reproduced with (I
think) any kernel >= 2.6.39 and the following XML (to be used with
"virsh net-create"):
<network>
<name>test-bridge</name>
<bridge name='testbr0' />
<ip family='ipv6' address='fd00::1' prefix='64'>
</ip>
</network>
(it happens even when you have an IPv4, too)
The problem is that since commit [1] (which, ironically, was made to
“help IPv6 autoconfiguration”) the linux bridge code makes bridges
behave like “real” devices regarding carrier detection. This makes the
bridges created by libvirt, which are started without any up devices,
stay with the NO-CARRIER flag set, and thus prevents DAD (Duplicate
address detection) from happening, thus letting the IPv6 address flagged
as “tentative”. Such addresses cannot be bound to (see RFC 2462), so
dnsmasq fails binding to it (for radvd, it detects that "interface XXX
is not RUNNING", thus that "interface XXX does not exist, ignoring the
interface" (sic)). It seems that this behavior was enhanced somehow with
commit [2] by avoiding setting NO-CARRIER on empty bridges, but I
couldn't reproduce this behavior on my kernel. Anyway, with the “dummy
tap to set MAC address” trick, this wouldn't work.
To fix this, the idea is to get the bridge's attached device to be up so
that DAD can happen (deactivating DAD altogether is not a good idea, I
think). Currently, libvirt creates a dummy TAP device to set the MAC
address of the bridge, keeping it down. But even if we set this device
up, it is not RUNNING as soon as the tap file descriptor attached to it
is closed, thus still preventing DAD. So, we must modify the API a bit,
so that we can get the fd, keep the tap device persistent, run the
daemons, and close it after DAD has taken place. After that, the bridge
will be flagged NO-CARRIER again, but the daemons will be running, even
if not happy about the device's state (but we don't really care about
the bridge's daemons doing anything when no up interface is connected to
it).
Other solutions that I envisioned were:
* Keeping the *-nic interface up: this would waste an fd for each
bridge during all its life. May be acceptable, I don't really
know.
* Stop using the dummy tap trick, and set the MAC address directly
on the bridge: it is possible since quite some time it seems,
even if then there is the problem of the bridge not being
RUNNING when empty, contrary to what [2] says, so this will need
fixing (and this fix only happened in 3.1, so it wouldn't work
for 2.6.39)
* Using the --interface option of dnsmasq, but I saw somewhere
that it's not used by libvirt for backward compatibility. I am
not sure this would solve this problem, though, as I don't know
how dnsmasq binds itself to it with this option.
This is why this patch does what's described earlier.
This patch also makes radvd start even if the interface is
“missing” (i.e. it is not RUNNING), as it daemonizes before binding to
it, and thus sometimes does it after the interface has been brought down
by us (by closing the tap fd), and then originally stops. This also
makes it stop yelling about it in the logs when the interface is down at
a later time.
[1]
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=1faa4356a3bd89ea11fb92752d897cff3a20ec0e
[2]
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=b64b73d7d0c480f75684519c6134e79d50c1b341
The bridge driver implementation of virNetworkUpdate() removes and
re-adds iptables rules any time a network has an <ip>, <forward>, or
<forward>/<interface> element updated. There are some types of
networks that have those elements and yet have no iptables rules
associated with them, and unfortunately the functions that remove/add
iptables rules don't check the type of network before attempting to
remove/add the rules, sometimes leading to an erroneous failure of the
entire update operation.
Under normal circumstances I would refactor the lower level functions
to be more robust, but to avoid code churn as much as possible, I've
just added extra checks directly to networkUpdate().
https://www.gnu.org/licenses/gpl-howto.html recommends that
the 'If not, see <url>.' phrase be a separate sentence.
* tests/securityselinuxhelper.c: Remove doubled line.
* tests/securityselinuxtest.c: Likewise.
* globally: s/; If/. If/
Two changes are introduced in this patch:
- The first change removes ATTRIBUTE_RETURN_CHECK from
virNetDevBandwidthClear, because it was called with ignore_value
always, anyway. The function is used even when it's not necessary
to call it, just for cleanup purposes.
- The second change is added ignoring of the command's exit status,
since it may report an error even when run just as "to be sure we
clean up" function. No libvirt errors are suppresed by this.
A user on IRC had accidentally killed all of his libvirt-started
dnsmasq instances (due to a buggy dnsmasq service script in Fedora
16), and had hoped that libvirtd would notice this on restart and
reload all the dnsmasq daemons (as it does with iptables
rules). Unfortunately this was not the case - as long as the network
object had a pid registered for dnsmasq and/or radvd, it assumed that
the processes were running.
This patch takes advantage of the new utility functions in
bridge_driver.c to do a "refresh" of all radvd and dnsmasq processes
started by libvirt each time libvirtd is restarted - this function
attempts to do a SIGHUP of each existing process, and if that fails,
it restarts the process, rebuilding all the associated config files
and commandline parameters in the process. This normally has no
effect, but will be useful in solving the occasional "odd situation"
without needing to take the drastic step of destroying/re-starting the
network.
Call the network_conf function that modifies the live/persistent/both
config, then refresh/restart dnsmasq/radvd if necessary, and finally
save the config in the proper place(s).
This patch also needed to uncomment a few utility functions that were
added inside #if 0 in the previous commit (to avoid compiler errors
due to unreferenced static functions).
This patch splits the starting of dnsmasq and radvd into multiple
files, and adds new networkRefreshXX() and networkRestartXX()
functions for each. These new functions are currently commented out
because they won't be used until the next commit, and the compile options
require all static functions to be used.
networkRefreshXX() - rewrites any file-based config for dnsmasq/radvd,
and sends SIGHUP to the process to make it reread its config. If the
program isn't already running, it's just started.
networkRestartXX() - kills the given program, waits for it to exit
(see the comments in the function networkKillDaemon()), then calls
networkStartXX().
This commit is here mostly as a checkpoint to verify no change in
functional behavior after refactoring networkStartXX() functions to
fit in with these new functions.
These new functions are highly inspired by those in domain_conf.c (but
not identical), and are intended to make it simpler to update the
various combinations of live/persistent network configs.
The network driver wasn't previously as careful about the separation
between the live "status" in network->def and the persistent "config"
in network->newDef (or sometimes in network->def). This series
attempts to remedy some of that, but probably doesn't go all the way
(enough to get these functions working and enable continued work on
virNetworkUpdate though).
bridge_driver.c and test_driver.c were updated in a few places to take
advantage of the new functions and/or account for changes in argument
lists.
This patch removed the "--filterwin2k" dnsmasq command line
parameter which was unnecessary for domain specification,
possibly blocked some usage, and was command line clutter.
Gene Czarcinski <gene@czarc.net>
libvirt's network config documents that a bridge's STP "forward delay"
(called "delay" in the XML) should be specified in seconds, but
virNetDevBridgeSetSTPDelay() assumes that it is given a delay in
milliseconds (although the comment at the top of the function
incorrectly says "seconds".
This fixes the comment, and converts the delay to milliseconds before
calling virNetDevBridgeSetSTPDelay().
dnsmasq is forwarding a number of queries upstream that should not
be done. There still remains an MX query for a plain name with no
domain specified that will be forwarded is dnsmasq has --domain=xxx
--local=/xxx/ specified. This does not happen with no domain name
and --local=// ... not a libvirt problem.
BTW, thanks again to Claudio Bley!
* configure.ac, spec file: firewalld defaults to enabled if dbus is
available, otherwise is disabled. If --with_firewalld is explicitly
requested and dbus is not available, configure will fail.
* bridge_driver: add dbus filters to get the FirewallD1.Reloaded
signal and DBus.NameOwnerChanged on org.fedoraproject.FirewallD1.
When these are encountered, reload all the iptables reuls of all
libvirt's virtual networks (similar to what happens when libvirtd is
restarted).
* iptables, ebtables: use firewall-cmd's direct passthrough interface
when available, otherwise use iptables and ebtables commands. This
decision is made once the first time libvirt calls
iptables/ebtables, and that decision is maintained for the life of
libvirtd.
* Note that the nwfilter part of this patch was separated out into
another patch by Stefan in V2, so that needs to be revised and
re-reviewed as well.
================
All the configure.ac and specfile changes are unchanged from Thomas'
V3.
V3 re-ran "firewall-cmd --state" every time a new rule was added,
which was extremely inefficient. V4 uses VIR_ONCE_GLOBAL_INIT to set
up a one-time initialization function.
The VIR_ONCE_GLOBAL_INIT(x) macro references a static function called
vir(Ip|Eb)OnceInit(), which will then be called the first time that
the static function vir(Ip|Eb)TablesInitialize() is called (that
function is defined for you by the macro). This is
thread-safe, so there is no chance of any race.
IMPORTANT NOTE: I've left the VIR_DEBUG messages in these two init
functions (one for iptables, on for ebtables) as VIR_WARN so that I
don't have to turn on all the other debug message just to see
these. Even if this patch doesn't need any other modification, those
messages need to be changed to VIR_DEBUG before pushing.
This one-time initialization works well. However, I've encountered
problems with testing:
1) Whenever I have enabled the firewalld service, *all* attempts to
call firewall-cmd from within libvirtd end with firewall-cmd hanging
internally somewhere. This is *not* the case if firewall-cmd returns
non-0 in response to "firewall-cmd --state" (i.e. *that* command runs
and returns to libvirt successfully.)
2) If I start libvirtd while firewalld is stopped, then start
firewalld later, this triggers libvirtd to reload its iptables rules,
however it also spits out a *ton* of complaints about deletion failing
(I suppose because firewalld has nuked all of libvirt's rules). I
guess we need to suppress those messages (which is a more annoying
problem to fix than you might think, but that's another story).
3) I noticed a few times during this long line of errors that
firewalld made a complaint about "Resource Temporarily
unavailable. Having libvirtd access iptables commands directly at the
same time as firewalld is doing so is apparently problematic.
4) In general, I'm concerned about the "set it once and never change
it" method - if firewalld is disabled at libvirtd startup, causing
libvirtd to always use iptables/ebtables directly, this won't cause
*terrible* problems, but if libvirtd decides to use firewall-cmd and
firewalld is later disabled, libvirtd will not be able to recover.
This patch updates the network driver to properly utilize the new
attributes/elements that are now in virNetworkDef
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: Laine Stump <laine@laine.org>
The network pool should be able to keep track of both network device
names and PCI addresses, and return the appropriate one in the
actualDevice when networkAllocateActualDevice is called.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
This patch introduces the new forward mode='hostdev' along with
attribute managed. Includes updates to the network RNG and new xml
parser/formatter code.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Existing code that creates a list of forwardIfs from a single PF
was moved to the new utility function networkCreateInterfacePool.
No functional change.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Add the ability to support VLAN tags for Open vSwitch virtual port
types. To accomplish this, modify virNetDevOpenvswitchAddPort and
virNetDevTapCreateInBridgePort to take a virNetDevVlanPtr
argument. When adding the port to the OVS bridge, setup either a
single VLAN or a trunk port based on the configuration from the
virNetDevVlanPtr.
Signed-off-by: Kyle Mestery <kmestery@cisco.com>
The network driver now looks for the vlan element in network and
portgroup objects, and logs an error at network define time if a vlan
is requested for a network type that doesn't support it. (Currently
vlan configuration is only supported for openvswitch networks, and
networks used to do hostdev assignment of SR-IOV VFs.)
At runtime, the three potential sources of vlan information are
examined in this order: interface, chosen portgroup, network, and the
first that is non-empty is used. Another check for valid network type
is made at this time, since the interface may have requested a vlan (a
legal thing to have in the interface config, since it's not known
until runtime if the chosen network will actually support it).
Since we must also check for domains requesting vlans for unsupported
connection types even if they are type='network', and since
networkAllocateActualDevice() is being called in exactly the correct
places, and has all of the necessary information to check, I slightly
modified the logic of that function so that interfaces that aren't
type='network' don't just return immediately. Instead, they also
perform all the same validation for supported features. Because of
this, it's not necessary to make this identical check in the other
three places that would normally require it: 1) qemu domain startup,
2) qemu device hotplug, 3) lxc domain startup.
This can be seen as a first step in consolidating network-related
functionality into the network driver, rather than having copies of
the same code spread around in multiple places; this will make it
easier to split the network parts off into a separate daemon, as we've
discussed recently.
Just as each physical device used by a network has a connections
counter, now each network has a connections counter which is
incremented once for each guest interface that connects using this
network.
The count is output in the live network XML, like this:
<network connections='20'>
...
</network>
It is read-only, and for informational purposes only - it isn't used
internally anywhere by libvirt.
A later patch will be adding a counter that will be
incremented/decremented each time an guest interface starts/stops
using a particular network. For this to work, all types of networks
need to go through a common return sequence rather than returning
early. To setup for this, a new success: label is added (when
necessary), a new error: label is added which does any cleanup
necessary only for error returns and then does goto cleanup, and early
returns are changed to goto error if it's a failure, or goto success
if it's successful. This way the intent of all the gotos is
unambiguous, and a successful return path never encounters the
"error:" label.
I want to include this count in the xml output of networks, but
calling it "connections" in the XML sounds better than "usageCount", and it
would be better if the name in the XML matched the variable name.
In a few places, usageCount was being initialized to 0, but this is
unnecessary, because VIR_ALLOC_N zero-fills everything anyway.
One of the original ideas behind allowing a <virtualport> in an
interface definition as well as in the <network> definition *and*one
or more <portgroup>s within the network, was that guest-specific
parameteres (like instanceid and interfaceid) could be given in the
interface's virtualport, and more general things (portid, managerid,
etc) could be given in the network and/or portgroup, with all the bits
brought together at guest startup time and combined into a single
virtualport to be used by the guest. This was somehow overlooked in
the implementation, though - it simply picks the "most specific"
virtualport, and uses the entire thing, with no attempt to merge in
details from the others.
This patch uses virNetDevVPortProfileMerge3() to combine the three
possible virtualports into one, then uses
virNetDevVPortProfileCheck*() to verify that the resulting virtualport
type is appropriate for the type of network, and that all the required
attributes for that type are present.
An example of usage is this: assuming a <network> definitions on host
ABC of:
<network>
<name>testA</name>
...
<virtualport type='openvswitch'/>
...
<portgroup name='engineering'>
<virtualport>
<parameters profileid='eng'/>
</virtualport>
</portgroup>
<portgroup name='sales'>
<virtualport>
<parameters profileid='sales'/>
</virtualport>
</portgroup>
</network>
and the same <network> on host DEF of:
<network>
<name>testA</name>
...
<virtualport type='802.1Qbg'>
<parameters typeid="1193047" typeidversion="2"/>
</virtualport>
...
<portgroup name='engineering'>
<virtualport>
<parameters managerid="11"/>
</virtualport>
</portgroup>
<portgroup name='sales'>
<virtualport>
<parameters managerid="55"/>
</virtualport>
</portgroup>
</network>
and a guest <interface> definition of:
<interface type='network'>
<source network='testA' portgroup='sales'/>
<virtualport>
<parameters instanceid="09b11c53-8b5c-4eeb-8f00-d84eaa0aaa4f"
interfaceid="09b11c53-8b5c-4eeb-8f00-d84eaa0aaa4f"\>
</virtualport>
...
</interface>
If the guest was started on host ABC, the <virtualport> used would be:
<virtualport type='openvswitch'>
<parameters interfaceid='09b11c53-8b5c-4eeb-8f00-d84eaa0aaa4f'
profileid='sales'/>
</virtualport>
but if that guest was started on host DEF, the <virtualport> would be:
<virtualport type='802.1Qbg'>
<parameters instanceid="09b11c53-8b5c-4eeb-8f00-d84eaa0aaa4f"
typeid="1193047" typeidversion="2"
managerid="55"/>
</virtualport>
Additionally, if none of the involved <virtualport>s had a specified type
(this includes cases where no virtualport is given at all),
virtPortProfile is now used by 4 different types of network devices
(NETWORK, BRIDGE, DIRECT, and HOSTDEV), and it's getting cumbersome to
replicate so much code in 4 different places just because each type
has the virtPortProfile in a slightly different place. This patch puts
a single virtPortProfile in a common place (outside the type-specific
union) in both virDomainNetDef and virDomainActualNetDef, and adjusts
the parse and format code (and the few other places where it is used)
accordingly.
Note that when a <virtualport> element is found, the parse functions
verify that the interface is of a type that supports one, otherwise an
error is generated (CONFIG_UNSUPPORTED in the case of <interface>, and
INTERNAL in the case of <actual>, since the contents of <actual> are
always generated by libvirt itself).
Per the FSF address could be changed from time to time, and GNU
recommends the following now: (http://www.gnu.org/licenses/gpl-howto.html)
You should have received a copy of the GNU General Public License
along with Foobar. If not, see <http://www.gnu.org/licenses/>.
This patch removes the explicit FSF address, and uses above instead
(of course, with inserting 'Lesser' before 'General').
Except a bunch of files for security driver, all others are changed
automatically, the copyright for securify files are not complete,
that's why to do it manually:
src/security/security_selinux.h
src/security/security_driver.h
src/security/security_selinux.c
src/security/security_apparmor.h
src/security/security_apparmor.c
src/security/security_driver.c
Update the linux bridge driver to use virReportError instead
of the networkReportError custom macro
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Introduce new members in the virMacAddr 'class'
- virMacAddrSet: set virMacAddr from a virMacAddr
- virMacAddrSetRaw: setting virMacAddr from raw 6 byte MAC address buffer
- virMacAddrGetRaw: writing virMacAddr into raw 6 byte MAC address buffer
- virMacAddrCmp: comparing two virMacAddr
- virMacAddrCmpRaw: comparing a virMacAddr with a raw 6 byte MAC address buffer
then replace raw MAC addresses by replacing
- 'unsigned char *' with virMacAddrPtr
- 'unsigned char ... [VIR_MAC_BUFLEN]' with virMacAddr
and introduce usage of above functions where necessary.
commit 52d064f42d added
VIR_NETWORK_XML_INACTIVE in order to allow suppressing the
auto-generated list of VFs in network definitions, and a --inactive
flag to virsh net-dumpxml to take advantage of the flag. However, it
missed out on two opportunities:
1) Use INACTIVE to get the current config of the network as it
exists on disk, rather than the currently active config.
2) Add INACTIVE to the flags used for the virsh net-edit command, so
that it won't include the forward-pool interfaces that were
autogenerated, and so that a re-edit of the network prior to
restarting it will show any other edits made since the last restart
of the network. (prior to this patch, if you edited a network a 2nd
time without restarting, all of the previous edits would magically
disappear).
In order to fit with the new #define-based generic edit function in
virsh.c, a new function vshNetworkGetXMLDesc() was added. This
function first tries to call virNetworkGetXMLDesc with the INACTIVE
flag added, then retries without if the first attempt fails (in the
manner expected when the server doesn't support it).
Remove the uid param from virGetUserConfigDirectory,
virGetUserCacheDirectory, virGetUserRuntimeDirectory,
and virGetUserDirectory
These functions were universally called with the
results of getuid() or geteuid(). To make it practical
to port to Win32, remove the uid parameter and hardcode
geteuid()
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As defined in:
http://standards.freedesktop.org/basedir-spec/basedir-spec-latest.html
This offers a number of advantages:
* Allows sharing a home directory between different machines, or
sessions (eg. using NFS)
* Cleanly separates cache, runtime (eg. sockets), or app data from
user settings
* Supports performing smart or selective migration of settings
between different OS versions
* Supports reseting settings without breaking things
* Makes it possible to clear cache data to make room when the disk
is filling up
* Allows us to write a robust and efficient backup solution
* Allows an admin flexibility to change where data and settings are stored
* Dramatically reduces the complexity and incoherence of the
system for administrators
