On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
Currently each USB2 companion controller gets put on a separate
PCI slot. Not only is this wasteful of PCI slots, but it is not
in compliance with the spec for USB2 controllers. The master
echi1 and all companion controllers should be in the same slot,
with echi1 in function 7, and uhci1-3 in functions 0-2 respectively.
* src/qemu/qemu_command.c: Special case handling of USB2 controllers
to apply correct pci slot assignment
* tests/qemuxml2argvdata/qemuxml2argv-usb-ich9-ehci-addr.args,
tests/qemuxml2argvdata/qemuxml2argv-usb-ich9-ehci-addr.xml: Expand
test to cover automatic slot assignment
When support for was added for PCI multifunction cards (in commit
9f8baf, first included in libvirt 0.9.3), it was done by always
turning on the multifunction bit for all PCI devices. Since that time
it has been realized that this is not an ideal solution, and that the
multifunction bit must be selectively turned on. For example, see
https://bugzilla.redhat.com/show_bug.cgi?id=728174
and the discussion before and after
https://www.redhat.com/archives/libvir-list/2011-September/msg01036.html
This patch modifies multifunction support so that the multifunction=on
option is only added to the qemu commandline for a device if its PCI
<address> definition has the attribute "multifunction='on'", e.g.:
<address type='pci' domain='0x0000' bus='0x00'
slot='0x04' function='0x0' multifunction='on'/>
In practice, the multifunction bit should only be turned on if
function='0' AND other functions will be used in the same slot - it
usually isn't needed for functions 1-7 (although there are apparently
some exceptions, e.g. the Intel X53 according to the QEMU source
code), and should never be set if only function 0 will be used in the
slot. The test cases have been changed accordingly to illustrate.
With this patch in place, if a user attempts to assign multiple
functions in a slot without setting the multifunction bit for function
0, libvirt will issue an error when the domain is defined, and the
define operation will fail. In the future, we may decide to detect
this situation and automatically add multifunction=on to avoid the
error; even then it will still be useful to have a manual method of
turning on multifunction since, as stated above, there are some
devices that excpect it to be turned on for all functions in a slot.
A side effect of this patch is that attempts to use the same PCI
address for two different devices will now log an error (previously
this would cause the domain define operation to fail, but there would
be no log message generated). Because the function doing this log was
almost completely rewritten, I didn't think it worthwhile to make a
separate patch for that fix (the entire patch would immediately be
obsoleted).
QEMU uses USB bus name "usb.0" when using the legacy -usb argument.
If we want to allow USB devices to specify their addresses with legacy
-usb, we should either in case of legacy bus name drop the 0 from the
address bus, or just drop the 0 from device id. This patch does the
later.
Another solution would be to permit addressing on non-legacy USB
controllers only.
