Use virDomainDefAddUSBController() to add an EHCI1+UHCI1+UHCI2+UHCI3
controller set to newly defined Q35 domains that don't have any USB
controllers defined.
This new function will add a single controller of the given model,
except the case of ich9-usb-ehci1 (the master controller for a USB2
controller set) in which case a set of related controllers will be
added (EHCI1, UHCI1, UHCI2, UHCI3). These controllers will not be
given PCI addresses, but should be otherwise ready to use.
"-1" is allowed for controller model, and means "default for this
machinetype". This matches the existing practice in
qemuDomainDefPostParse(), which always adds the default controller
with model = -1, and relies on the commandline builder to set a model
(that is wrong, but will be fixed later).
We need a virDomainDefAddController() that doesn't check for an
existing controller at the same index (since USB2 controllers must be
added in sets of 4 that are all at the same index), so rather than
duplicating the code in virDomainDefMaybeAddController(), split it
into two functions, in the process eliminating existing duplicated
code that loops through the controller list by calling
virDomainControllerFind(), which does the same thing).
The real Q35 machine puts the first USB controller set (EHCI+(UHCIx4))
on bus 0 slot 0x1D, and the 2nd USB controller set on bus 0 slot 0x1A,
so let's attempt to make the virtual machine match that for
controllers with auto-assigned addresses when possible.
Three test cases were added to assure that the proper addresses are
assigned - one with a single set of unaddressed USB controllers, one
with 3 (to grab both preferred slots plus one more), and one with the
order of the controller definitions reordered, to assure that the
auto-assignment isn't mixed up by order.
When qemuAssignDevicePCISlots() is looking for companion controllers
for a USB controller that has no PCI address specified, it initializes
a virDevicePCIAddress to 0000:00:00.0, fills it in with the
companion's address if one is found, then checks whether or not there
was a find based on slot == 0. On a system with a single PCI bus, that
is a valid way to check, because slot 0 is reserved, but on most other
PCI buses, slot 0 is not reserved, and is open for use by any
device. This patch adds a separate bool that is set when a companion
is found rather than relying on the faulty information provided with
"slot == 0".
Some of the protocol files already include handing of the missing int
types such as xdr_uint64_t, some don't. To fix it everywhere, move out
of the appropriate defines to the utils/virxdrdefs.h file and include
it where needed.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
OpenBSD uses 'struct sockpeercred' instead of 'struct ucred'. Add a
configure check that detects its presence and use if in the code that
could be compiled on OpenBSD.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
As cgroup implementation only works on Linux, it does not
make much sense to include sys/mount.h if other requirements are
not met, such as HAVE_MNTENT_H and HAVE_GETMNTENT_R.
Also, it fixes build on OpenBSD that requires to include sys/param.h
along with sys/mount.h.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
In wireshark commit ceb8d954 (v1.99.2) they have changed the
signature of a function that determines how long a libvirt packet
is. Now it accepts a void pointer for passing data into the
function. Well, this is nice, but we don't need it right now.
Anyway, we have to change our code.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In the upcoming patch we will need yet another #ifdef code block
depending on wireshark version. Instead of defining
WIRESHARK_COMPAT2 or something lets just compare the version
right at the place so that we can clearly see what version broke
API.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In wireshak commit 22149c55 (v.1.11.3) the API was renamed.
Follow the change in our code too. Since the wireshark change was
made in the very same version that we require at least we are
good to go.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In wireshark, they have introduced their own memory allocator
wmem. This means that we need to adapt our code to that change
too. Notably 0ad15f88ccf434e8210ca is the wireshark commit you
want to look at. It's the one where they dropped the old API. The
new allocator has been introduced in 84cc3daa (v1.10.0), however,
was not exposed until 5c05c9e0 (v1.10.0). Since we already are
requiring 1.11.3 or higher no other change is needed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In the wireshark commit e2735ecfdd7a96c they dropped
proto_tree_add_text in favor of proto_tree_add_item. Adapt to
this change.
Moreover, the proto_tree_add_item API is around for ages and we
are already using it anyway. Therefore we don't need to change
required version of wireshark.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
While this is no functional change, whole channel definition is
going to be needed very soon. Moreover, while touching this obey
const correctness rule in qemuAgentOpen() - so far it was passed
regular pointer to channel config even though the function is
expected to not change pointee at all. Pass const pointer
instead.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In qemu driver we listen to virtio channel events like an agent
connected to or disconnected from the guest part of socket.
However, with a little exception - when we find out that the
socket in question is the guest agent one, we connect or
disconnect guest agent which is done prior setting new state in
internal structure. Due to a bug in our code it may happen that
we got the event but failed to set it in internal structure
representing the channel.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Commit b22344f328 mistakenly reordered
Default-* lines. Thanks to that I noticed that we are very inconsistent
with our init scripts, so I took the liberty of synchronizing them,
updating them and making them all look shiny and new. So apart from
fixing the LSB requirements, I also fixed the ordering, specified
runlevels and fix the link to the reference specification.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
We have a policy that if API may end up talking to a guest agent
it should require RW connection. We don't obey the rule in
virDomainGetTime().
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This API does not change domain state. However, we have a policy
that an API talking to a guest agent requires RW access. But that
happens only if source == VIR_DOMAIN_INTERFACE_ADDRESSES_SRC_AGENT.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Implement a --timestamp option for 'virsh net-event', similar to the
one for 'virsh event'.
When the option is used, the human-readable timestamp will be printed
before the message.
Implement a --timestamp option for 'virsh qemu-monitor-event', similar
to the one for 'virsh event'.
When the option is used, the human-readable timestamp will be printed
before the message, and the timing information provided by QEMU will
not be displayed.
Earlier commit 7140807917 forgot to deal
properly with status XMLs where we want the libvirt-internal paths to be
kept in place and not cleared, otherwise we could end up copying a NULL
string and segfaulting th daemon.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If the q35 specific disable s3/s4 setting isn't supported, fallback to
specifying the PIIX setting, which is the previous behavior. It doesn't
have any effect, but qemu will just warn about it rather than error:
qemu-system-x86_64: Warning: global PIIX4_PM.disable_s3=1 not used
qemu-system-x86_64: Warning: global PIIX4_PM.disable_s4=1 not used
Since it doesn't error, I don't think we should either, since there
may be configs in the wild that already have q35 + disable_s3/4 (via
virt-manager)
Using one Makefile per example subdirectory essentially serializes 'make'
calls. Convert to one example/Makefile that builds and distributes
all the subdir files. This reduces example/ rebuild time from about 5.8
seconds to 1.5 seconds on my machine.
One slight difference is that we no longer ship Makefile.am with the
examples in the rpm. This was virtually useless anyways since the Makefile
was very specific to libvirt infrastructure, so wasn't generically
reusable anyways.
Tested with 'make distcheck' and 'make rpm'
No only coverity warns about this, but it kind of makes sense
too. We have a test whether host supports IOMMU. Some platforms
don't have it, I know. But in that case we should print a message
that it's unknown whether platform has it or not.
Before:
(no output)
After:
QEMU: Checking for device assignment IOMMU support : WARN (Unknown if this platform has IOMMU support)
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This function may be called with @dconnuri == NULL, e.g. from
virDomainMigrateToURI3() if the flags are missing
VIR_MIGRATE_PEER2PEER flag. Moreover, all later functions called
from here do wrap it into NULLSTR() so why not do the same here?
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The condition was checking for UHCI (and OHCI for ppc64) availability so
that it can specify the proper device instead of legacy usb. However,
for ppc64, we don't need to check both OHCI and UHCI, but only OHCI as
that is the legacy default. The condition is so big that it was just a
matter of time when someone will make a mistake there, so let's use more
lines so that it is visible what the condition checks for.
This fixes usage of -device instead of -usb for ppc64 that supports
pci-usb-ohci and does not support piix3-usb-uhci.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1297020
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
For some reason we are not setting the driver with memset() to zeros.
But since commit 74abc3deac
driver->securityManager is being accessed and qemuagenttest started
crashing due to that.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Future changes will make some of these tests dependent on specific
QEMUCaps flags, so wire up the basic handling. Flags will be added
in future patches.
For the standard active/inactive XML testing, if we leave the file loading
up to the generic XML2XML infrastructure, we get the benefit of
VIR_TEST_REGENERATE_OUTPUT, at the price of a few more disk reads. Seems
worth it.
Since test files are formatted predictably nowadays, we can make
VIR_TEST_REGENERATE_OUTPUT handle most cases for us with a simple
replacement. test-wrap-argv.pl is still canon, but this bit makes
it easier to confirm test output changes during active development.
The libxl_device_nic structure supports specifying an outgoing rate
limit based on a time interval and bytes allowed per interval. In xl
config a rate limit is specified as "<RATE>/s@<INTERVAL>". INTERVAL
is optional and defaults to 50ms.
libvirt expresses outgoing limits by average (required), peak, burst,
and floor attributes in units of KB/s. This patch supports the outgoing
bandwidth limit by converting the average KB/s to bytes per interval
based on the same default interval (50ms) used by xl.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Both xm and xl config have long supported specifying vif rate
limiting, e.g.
vif = [ 'mac=00:16:3E:74:3d:76,bridge=br0,rate=10MB/s' ]
Add support for mapping rate to and from <bandwidth> in the xenconfig
parser and formatter. rate is mapped to the required 'average' attribute
of the <outbound> element, e.g.
<interface type='bridge'>
...
<bandwidth>
<outbound average='10240'/>
</bandwidth>
</interface>
Also add a unit test to check the conversion logic.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
The xen sexpr config format has long supported specifying vif rate
limiting, e.g.
(device
(vif
(mac '00:16:3e:1b:b1:47')
(rate '10240KB/s')
...
)
)
Add support for mapping rate to and from <bandwidth> in the xenconfig
sexpr parser and formatter. rate is mapped to the required 'average'
attribute of the <outbound> element, e.g.
<interface type='bridge'>
...
<bandwidth>
<outbound average='10240'/>
</bandwidth>
</interface>
Also add unit tests to check the conversion logic.
This patch benefits both the old xen driver and the libxl driver.
Both drivers gain support for vif bandwidth when converting to/from
domXML and xen-sxpr. In addition, the old xen driver will now be
able to handle vif 'rate' setting when communicating with xend.
