Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.1 the -drive argument can be used to configure
all disks, so the QEMU driver can assume it is always available
and drop support for -hda/-cdrom/etc.
Many of the tests need updating because a great many were
running without CAPS_DRIVE set, so using the -hda legacy
syntax.
Fixing the tests uncovered a bug in the argv -> xml
convertor which failed to handle disk with if=floppy.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
This patch makes sure that each network device ("interface") of
type='hostdev' appears on both the hostdevs list and the nets list of
the virDomainDef, and it modifies the qemu driver startup code so that
these devices will be presented to qemu on the commandline as hostdevs
rather than as network devices.
It does not add support for hotplug of these type of devices, or code
to honor the <mac address> or <virtualport> given in the config (both
of those will be done in separate patches).
Once each device is placed on both lists, much of what this patch does
is modify places in the code that traverse all the device lists so
that these hybrid devices are only acted on once - either along with
the other hostdevs, or along with the other network interfaces. (In
many cases, only one of the lists is traversed / a specific operation
is performed on only one type of device. In those instances, the code
can remain unchanged.)
There is one special case - when building the commandline, interfaces
are allowed to proceed all the way through
networkAllocateActualDevice() before deciding to skip the rest of
netdev-specific processing - this is so that (once we have support for
networks with pools of hostdev devices) we can get the actual device
allocated, then rely on the loop processing all hostdevs to generate
the correct commandline.
(NB: <interface type='hostdev'> is only supported for PCI network
devices that are SR-IOV Virtual Functions (VF). Standard PCI[e] and
USB devices, and even the Physical Functions (PF) of SR-IOV devices
can only be assigned to a guest using the more basic <hostdev> device
entry. This limitation is mostly due to the fact that non-SR-IOV
ethernet devices tend to lose mac address configuration whenever the
card is reset, which happens when a card is assigned to a guest;
SR-IOV VFs fortunately don't suffer the same problem.)
