this is the patch to add support for multiple serial ports to the
libvirt Xen driver. It support both old style (serial = "pty") and
new style (serial = [ "/dev/ttyS0", "/dev/ttyS1" ]) definition and
tests for xml2sexpr, sexpr2xml and xmconfig have been added as well.
Written and tested on RHEL-5 Xen dom0 and working as designed but
the Xen version have to have patch for RHBZ #614004 but this patch
is for upstream version of libvirt.
Also, this patch is addressing issue described in RHBZ #670789.
Signed-off-by: Michal Novotny <minovotn@redhat.com>
When executed from cron, commandtest would fail to correctly
identify daemon processes. Set session ID and process group
IDs at startup to ensure we have a consistent environment to
run in.
* tests/commandtest.c: Call setsid() and setpgid()
This is done for two reasons:
- we are getting very close to 64 flags which is the maximum we can use
with unsigned long long
- by using LL constants in enum we already violates C99 constraint that
enum values have to fit into int
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=609463
The problem was that, since a bridge always acquires the MAC address
of the connected interface with the numerically lowest MAC, as guests
are started and stopped, it was possible for the MAC address to change
over time, and this change in the network was being detected by
Windows 7 (it sees the MAC of the default route change), so on each
reboot it would bring up a dialog box asking about this "new network".
The solution is to create a dummy tap interface with a MAC guaranteed
to be lower than any guest interface's MAC, and attach that tap to the
bridge as soon as it's created. Since all guest MAC addresses start
with 0xFE, we can just generate a MAC with the standard "0x52, 0x54,
0" prefix, and it's guaranteed to always win (physical interfaces are
never connected to these bridges, so we don't need to worry about
competing numerically with them).
Note that the dummy tap is never set to IFF_UP state - that's not
necessary in order for the bridge to take its MAC, and not setting it
to UP eliminates the clutter of having an (eg) "virbr0-nic" displayed
in the output of the ifconfig command.
I chose to not auto-generate the MAC address in the network XML
parser, as there are likely to be consumers of that API that don't
need or want to have a MAC address associated with the
bridge.
Instead, in bridge_driver.c when the network is being defined, if
there is no MAC, one is generated. To account for virtual network
configs that already exist when upgrading from an older version of
libvirt, I've added a %post script to the specfile that searches for
all network definitions in both the config directory
(/etc/libvirt/qemu/networks) and the state directory
(/var/lib/libvirt/network) that are missing a mac address, generates a
random address, and adds it to the config (and a matching address to
the state file, if there is one).
docs/formatnetwork.html.in: document <mac address.../>
docs/schemas/network.rng: add nac address to schema
libvirt.spec.in: %post script to update existing networks
src/conf/network_conf.[ch]: parse and format <mac address.../>
src/libvirt_private.syms: export a couple private symbols we need
src/network/bridge_driver.c:
auto-generate mac address when needed,
create dummy interface if mac address is present.
tests/networkxml2xmlin/isolated-network.xml
tests/networkxml2xmlin/routed-network.xml
tests/networkxml2xmlout/isolated-network.xml
tests/networkxml2xmlout/routed-network.xml: add mac address to some tests
This is in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=629662
Explanation
qemu's virtio-net-pci driver allows setting the algorithm used for tx
packets to either "bh" or "timer". This is done by adding ",tx=bh" or
",tx=timer" to the "-device virtio-net-pci" commandline option.
'bh' stands for 'bottom half'; when this is set, packet tx is all done
in an iothread in the bottom half of the driver. (In libvirt, this
option is called the more descriptive "iothread".)
'timer' means that tx work is done in qemu, and if there is more tx
data than can be sent at the present time, a timer is set before qemu
moves on to do other things; when the timer fires, another attempt is
made to send more data. (libvirt retains the name "timer" for this
option.)
The resulting difference, according to the qemu developer who added
the option is:
bh makes tx more asynchronous and reduces latency, but potentially
causes more processor bandwidth contention since the cpu doing the
tx isn't necessarily the cpu where the guest generated the
packets.
Solution
This patch provides a libvirt domain xml knob to change the option on
the qemu commandline, by adding a new attribute "txmode" to the
<driver> element that can be placed inside any <interface> element in
a domain definition. It's use would be something like this:
<interface ...>
...
<model type='virtio'/>
<driver txmode='iothread'/>
...
</interface>
I chose to put this setting as an attribute to <driver> rather than as
a sub-element to <tune> because it is specific to the virtio-net
driver, not something that is generally usable by all network drivers.
(note that this is the same placement as the "driver name=..."
attribute used to choose kernel vs. userland backend for the
virtio-net driver.)
Actually adding the tx=xxx option to the qemu commandline is only done
if the version of qemu being used advertises it in the output of
qemu -device virtio-net-pci,?
If a particular txmode is requested in the XML, and the option isn't
listed in that help output, an UNSUPPORTED_CONFIG error is logged, and
the domain fails to start.
QEMUD_CMD_FLAG_PCI_MULTIBUS should be set in the function
qemuCapsExtractVersionInfo()
The flag QEMUD_CMD_FLAG_PCI_MULTIBUS is used in the function
qemuBuildDeviceAddressStr(). All callers get qemuCmdFlags
by the function qemuCapsExtractVersionInfo() except that
testCompareXMLToArgvFiles() in qemuxml2argvtest.c.
So we should set QEMUD_CMD_FLAG_PCI_MULTIBUS in the function
qemuCapsExtractVersionInfo() instead of qemuBuildCommandLine()
because the function qemuBuildCommandLine() does not be called
when we attach a pci device.
tests: set QEMUD_CMD_FLAG_PCI_MULTIBUS in testCompareXMLToArgvFiles()
set QEMUD_CMD_FLAG_PCI_MULTIBUS before calling qemuBuildCommandLine()
as the flags is not set by qemuCapsExtractVersionInfo().
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
qemu 0.13.0 (at least as built for Fedora 14, and also backported to
RHEL 6.0 qemu) supported an older syntax for a spicevmc channel; it's
not as flexible (it has an implicit name and hides the chardev
aspect), but now that we support spicevmc, we might as well target
both variants.
* src/qemu/qemu_capabilities.h (QEMUD_CMD_FLAG_DEVICE_SPICEVMC):
New flag.
* src/qemu/qemu_capabilities.c (qemuCapsParseDeviceStr): Set it
correctly.
* src/qemu/qemu_command.h (qemuBuildVirtioSerialPortDevStr): Drop
declaration.
* src/qemu/qemu_command.c (qemuBuildVirtioSerialPortDevStr): Alter
signature, check flag.
(qemuBuildCommandLine): Adjust caller and check flag.
* tests/qemuhelptest.c (mymain): Update test.
* tests/qemuxml2argvtest.c (mymain): New test.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc-old.xml:
New file.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc-old.args:
Likewise.
Adds <smartcard mode='passthrough' type='spicevmc'/>, which uses the
new <channel name='smartcard'/> of <graphics type='spice'>.
* docs/schemas/domain.rng: Support new XML.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.h (virDomainGraphicsSpiceChannelName): New
enum value.
(virDomainChrSpicevmcName): New enum.
(virDomainChrSourceDef): Distinguish spicevmc types.
* src/conf/domain_conf.c (virDomainGraphicsSpiceChannelName): Add
smartcard.
(virDomainSmartcardDefParseXML): Parse it.
(virDomainChrDefParseXML, virDomainSmartcardDefParseXML): Set
spicevmc name.
(virDomainChrSpicevmc): New enum conversion functions.
* src/libvirt_private.syms: Export new functions.
* src/qemu/qemu_command.c (qemuBuildChrChardevStr): Conditionalize
name.
* tests/qemuxml2argvtest.c (domain): New test.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-passthrough-spicevmc.args:
New file.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-passthrough-spicevmc.xml:
Likewise.
Inspired by https://bugzilla.redhat.com/show_bug.cgi?id=615757
Add a new character device backend for virtio serial channels that
activates the QEMU spice agent on the main channel using the vdagent
spicevmc connection. The <target> must be type='virtio', and supports
an optional name that specifies how the guest will see the channel
(for now, name must be com.redhat.spice.0).
<channel type='spicevmc'>
<target type='virtio'/>
<address type='virtio-serial' controller='1' bus='0' port='3'/>
</channel>
* docs/schemas/domain.rng: Support new XML.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.h (virDomainChrType): New enum value.
* src/conf/domain_conf.c (virDomainChr): Add spicevmc.
(virDomainChrDefParseXML, virDomainChrSourceDefParseXML)
(virDomainChrDefParseTargetXML): Parse and enforce proper use.
(virDomainChrSourceDefFormat, virDomainChrDefFormat): Format.
* src/qemu/qemu_command.c (qemuBuildChrChardevStr)
(qemuBuildCommandLine): Add qemu support.
* tests/qemuxml2argvtest.c (domain): New test.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc.xml: New
file.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc.args:
Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Qemu smartcard/spicevmc support exists on branches (such as
http://cgit.freedesktop.org/~alon/qemu/commit/?h=usb_ccid.v15&id=024a37b)
but is not yet upstream. The added -help output matches a scratch build
that will be close to the RHEL 6.1 qemu-kvm.
* src/qemu/qemu_capabilities.h (QEMUD_CMD_FLAG_CCID_EMULATED)
(QEMUD_CMD_FLAG_CCID_PASSTHRU, QEMUD_CMD_FLAG_CHARDEV_SPICEVMC):
New flags.
* src/qemu/qemu_capabilities.c (qemuCapsComputeCmdFlags)
(qemuCapsParseDeviceStr): Check for smartcard capabilities.
(qemuCapsExtractVersionInfo): Tweak comment.
* tests/qemuhelptest.c (mymain): New test.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel61: New file.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel61-device: Likewise.
Assuming a hypervisor that supports multiple smartcard devices in the
guest, this would be a valid XML description:
<devices>
<smartcard mode='host'/>
<smartcard mode='host-certificates'>
<certificate>/path/to/cert1</certificate>
<certificate>/path/to/cert2</certificate>
<certificate>/path/to/cert3</certificate>
</smartcard>
<smartcard mode='passthrough' type='tcp'>
<source mode='bind' host='127.0.0.1' service='2001'/>
<protocol type='raw'/>
</smartcard>
</devices>
(As of this commit, the qemu hypervisor will be the first
implementation, but it only supports one smartcard.)
* docs/formatdomain.html.in (Smartcard devices): New section.
* docs/schemas/domain.rng (smartcard): New define, used in
devices.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-host.xml: New file
to test schema.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-host-certificates.xml:
Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-passthrough-tcp.xml:
Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-controller.xml:
Likewise.
This patch teaches testutil how to read multi-line input files with
backspace-newline line continuation markers.
The patch also breaks up all the single-line arguments test input files into
multi-line files with lines shorter than 80 characters.
* src/fdstream.c (virFDStreamOpenFile, virFDStreamCreateFile):
Use VIR_FORCE_CLOSE instead of close.
* tests/commandtest.c (mymain): Likewise.
* tools/virsh.c (editFile): Use virCommand instead of system.
* src/util/util.c (__virExec): Special case preservation of std
file descriptors to child.
Use it in all places where a memory or storage request size is converted
to a larger granularity. This avoids requesting too small memory or storage
sizes that could result from the truncation done by a simple division.
This extends the round up fix in 6002e0406c
to the whole codebase.
Instead of reporting errors for odd values in the VMX code round them up.
Update the QEMU Argv tests accordingly as the original memory size 219200
isn't a even multiple of 1024 and is rounded up to 215 megabyte now. Change
it to 219100 and 219136. Use two different values intentionally to make
sure that rounding up works.
Update virsh.pod accordingly, as rounding down and rejecting are replaced
by rounding up.
qemu allows the user to choose what io storage api should be used,
either the default (threads) or native (linux aio) which in the latter
case can result in better performance.
Based on a patch originally by Matthias Dahl.
Red Hat Bugzilla #591703
Signed-off-by: Eric Blake <eblake@redhat.com>
* src/qemu/qemu_command.c (qemuBuildChrChardevStr): Alter the
chardev alias.
(qemuBuildCommandLine): Output an id for the chardev counterpart.
* tests/qemuxml2argvdata/*: Update tests to match.
Reported by Daniel P. Berrange.
As noticed by Eric, commit 8e28c5d402,
which fixed generation of virtio-serial port numbers, forgot to adjust
test files which resulted in make check failure.
Regression introduced in commit e6b68d7 (Nov 2010).
Prior to that point, handlesAlloc was always a multiple of
EVENT_ALLOC_EXTENT (10), and was an int (so even if the subtraction
had been able to wrap, a negative value would be less than the count
not try to free the handles array). But after that point,
VIR_RESIZE_N made handlesAlloc grow geometrically (with a pattern of
10, 20, 30, 45 for the handles array) but still freed in multiples of
EVENT_ALLOC_EXTENT; and the count changed to size_t. Which means that
after 31 handles have been created, then 30 handles destroyed,
handlesAlloc is 5 while handlesCount is 1, and since (size_t)(1 - 5)
is indeed greater than 1, this then tried to free 10 elements, which
had the awful effect of nuking the handles array while there were
still live handles.
Nuking live handles puts libvirtd in an inconsistent state, and was
easily reproducible by starting and then stopping 60 faqemu guests.
* daemon/event.c (virEventCleanupTimeouts, virEventCleanupHandles):
Avoid integer wrap-around causing us to delete the entire array
while entries are still active.
* tests/eventtest.c (mymain): Expose the bug.
In QEMU, the card itself is a PCI device, but it requires a codec
(either -device hda-output or -device hda-duplex) to actually output
sound. Specifying <sound model='ich6'/> gives us -device intel-hda
-device hda-duplex I think it's important that a simple <sound model='ich6'/>
sets up a useful codec, to have consistent behavior with all other sound cards.
This is basically Dan's proposal of
<sound model='ich6'>
<codec type='output' slot='0'/>
<codec type='duplex' slot='3'/>
</sound>
without the codec bits implemented.
The important thing is to keep a consistent API here, we don't want some
<sound> devs require tweaking codecs but not others. Steps I see to
accomplishing this:
- every <sound> device has a <codec type='default'/> (unless codecs are
manually specified)
- <codec type='none'/> is required to specify 'no codecs'
- new audio settings like mic=on|off could then be exposed in
<sound> or <codec> in a consistent manner for all sound models
v2:
Use model='ich6'
v3:
Use feature detection, from eblake
Set codec id, bus, and cad values
v4:
intel-hda isn't supported if -device isn't available
v5:
Comment spelling fixes
QEMU supports serving VNC over a unix domain socket rather than traditional
TCP host/port. This is specified with:
<graphics type='vnc' socket='/foo/bar/baz'/>
This provides better security access control than VNC listening on
127.0.0.1, but will cause issues with tools that rely on the lax security
(virt-manager in fedora runs as regular user by default, and wouldn't be
able to access a socket owned by 'qemu' or 'root').
Also not currently supported by any clients, though I have patches for
virt-manager, and virt-viewer should be simple to update.
v2:
schema: Make listen vs. socket a <choice>
https://bugzilla.redhat.com/show_bug.cgi?id=620363
When using -incoming stdio or -incoming exec:, qemu keeps the
stdin fd open long after the migration is complete. Not to
mention that exec:cat is horribly inefficient, by doubling the
I/O and going through a popen interface in qemu.
The new -incoming fd: of qemu 0.12.0 closes the fd after using
it, and allows us to bypass an intermediary cat process for
less I/O.
* src/qemu/qemu_command.h (qemuBuildCommandLine): Add parameter.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Support
migration via fd: when possible. Consolidate migration handling
into one spot, now that it is more complex.
* src/qemu/qemu_driver.c (qemudStartVMDaemon): Update caller.
* tests/qemuxml2argvtest.c (mymain): Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-restore-v2-fd.args: New file.
* tests/qemuxml2argvdata/qemuxml2argv-restore-v2-fd.xml: Likewise.
Before the security driver was refactored in d6623003 seclabeltest and
secaatest were basically the same. seclabeltest was meant for SELinux
and secaatest for AppArmor. Both tests exited early when the specific
security driver backend wasn't enabled.
With the new security manager trying to initialize a disabled security
driver backend is an error that can't be distinguished from other errors
anymore. Therefore, the updated seclabeltest just asks for the first
available backend as this will always work even with SELinux and AppArmor
backend being disabled due to the new Nop backend.
Remove the obsolete secaatest and compile and run the seclabeltest
unconditional.
This fixes make check on systems that support AppArmor.
* src/qemu/qemu_capabilities.h (qemuCapsParseDeviceStr): New
prototype.
* src/qemu/qemu_capabilities.c (qemuCapsParsePCIDeviceStrs)
Rename and split...
(qemuCapsExtractDeviceStr, qemuCapsParseDeviceStr): ...to make it
easier to add and test device-specific checks.
(qemuCapsExtractVersionInfo): Update caller.
* tests/qemuhelptest.c (testHelpStrParsing): Also test parsing of
device-related flags.
(mymain): Update expected flags.
* tests/qemuhelpdata/qemu-0.12.1-device: New file.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel60-device: New file.
* tests/qemuhelpdata/qemu-kvm-0.12.3-device: New file.
* tests/qemuhelpdata/qemu-kvm-0.13.0-device: New file.
Commit 870dba0 (Mar 2008) added builddir/src to PATH to pick
up virsh. Later, virsh was moved to tools; commit db68d6b
(Oct 2009) noticed this, but only added the new location rather
than deleting the old location.
* tests/Makefile.am (path_add): Drop now-useless directory.
Suggested by Daniel P. Berrange.
Skip IB700 when assigning PCI slots.
Note: the I6300ESB watchdog _is_ a PCI device.
To test this: I applied this patch to libvirt-0.8.3-2.fc14 (rebasing
it slightly: qemu_command.c didn't exist in that version) and
installed this on my machine, then tested that I could successfully
add an ib700 watchdog device to a guest, start the guest, and the
ib700 was available to the guest. I also added an i6300esb (PCI)
watchdog to another guest, and verified that libvirt assigned a PCI
device to it, that the guest could be started, and that i6300esb was
present in the guest.
Note that if you previously had a domain with a ib700 watchdog, it
would have had an <address type='pci' .../> clause added to it in the
libvirt configuration. This patch does not attempt to remove this.
You cannot start such a domain -- qemu gives an error if you try.
With this patch you are able to remove the bogus address element
without libvirt adding it back.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
The current security driver usage requires horrible code like
if (driver->securityDriver &&
driver->securityDriver->domainSetSecurityHostdevLabel &&
driver->securityDriver->domainSetSecurityHostdevLabel(driver->securityDriver,
vm, hostdev) < 0)
This pair of checks for NULL clutters up the code, making the driver
calls 2 lines longer than they really need to be. The goal of the
patchset is to change the calling convention to simply
if (virSecurityManagerSetHostdevLabel(driver->securityDriver,
vm, hostdev) < 0)
The first check for 'driver->securityDriver' being NULL is removed
by introducing a 'no op' security driver that will always be present
if no real driver is enabled. This guarentees driver->securityDriver
!= NULL.
The second check for 'driver->securityDriver->domainSetSecurityHostdevLabel'
being non-NULL is hidden in a new abstraction called virSecurityManager.
This separates the driver callbacks, from main internal API. The addition
of a virSecurityManager object, that is separate from the virSecurityDriver
struct also allows for security drivers to carry state / configuration
information directly. Thus the DAC/Stack drivers from src/qemu which
used to pull config from 'struct qemud_driver' can now be moved into
the 'src/security' directory and store their config directly.
* src/qemu/qemu_conf.h, src/qemu/qemu_driver.c: Update to
use new virSecurityManager APIs
* src/qemu/qemu_security_dac.c, src/qemu/qemu_security_dac.h
src/qemu/qemu_security_stacked.c, src/qemu/qemu_security_stacked.h:
Move into src/security directory
* src/security/security_stack.c, src/security/security_stack.h,
src/security/security_dac.c, src/security/security_dac.h: Generic
versions of previous QEMU specific drivers
* src/security/security_apparmor.c, src/security/security_apparmor.h,
src/security/security_driver.c, src/security/security_driver.h,
src/security/security_selinux.c, src/security/security_selinux.h:
Update to take virSecurityManagerPtr object as the first param
in all callbacks
* src/security/security_nop.c, src/security/security_nop.h: Stub
implementation of all security driver APIs.
* src/security/security_manager.h, src/security/security_manager.c:
New internal API for invoking security drivers
* src/libvirt.c: Add missing debug for security APIs
This avoids throwing the tests off if LD_LIBRARY_PATH or LD_PRELOAD or
other variables are set.
Signed-off-by: Diego Elio Pettenò <flameeyes@gmail.com>
This commit adds support for IPv6 parsing and formatting to the
virtual network XML parser, including moving around data definitions
to allow for multiple <ip> elements on a single network, but only
changes the consumers of this API to accommodate for the changes in
API/structure, not to add any actual IPv6 functionality. That will
come in a later patch - this patch attempts to maintain the same final
functionality in both drivers that use the network XML parser - vbox
and "bridge" (the Linux bridge-based driver used by the qemu
hypervisor driver).
* src/libvirt_private.syms: Add new private API functions.
* src/conf/network_conf.[ch]: Change C data structure and
parsing/formatting.
* src/network/bridge_driver.c: Update to use new parser/formatter.
* src/vbox/vbox_tmpl.c: update to use new parser/formatter
* docs/schemas/network.rng: changes to the schema -
* there can now be more than one <ip> element.
* ip address is now an ip-addr (ipv4 or ipv6) rather than ipv4-addr
* new optional "prefix" attribute that can be used in place of "netmask"
* new optional "family" attribute - "ipv4" or "ipv6"
(will default to ipv4)
* define data types for the above
* tests/networkxml2xml(in|out)/nat-network.xml: add multiple <ip> elements
(including IPv6) to a single network definition to verify they are being
correctly parsed and formatted.
In practice this has always been optional, but the RNG has shown it as
mandatory, and since all the examples for make check had it, it was
never noticed. One of the existing test cases has been changed to
check for this.
I also noticed that the dhcp/host/ip was still defined as <text/>,
but should really be <ref name='ipv4-addr'/>
Now the VMware driver doesn't depend on the ESX driver anymore.
Add a WITH_VMX option that depends on WITH_ESX and WITH_VMWARE.
Also add a libvirt_vmx.syms file.
Move some escaping functions from esx_util.c to vmx.c.
Adapt the test suite, ESX and VMware driver to the new code layout.
When running 'make check' under a multi-cpu Dom0 xen machine,
nodeinfotest had a spurious failure it was reading from
/sys/devices/system/cpu, but xen has no notion of topology. The test
was intended to be isolated from reading any real system files; the
regression was introduced in Mar 2010 with commit aa2f6f96dd.
Fix things by allowing an early exit for the testsuite.
* src/nodeinfo.c (linuxNodeInfoCPUPopulate): Add parameter.
(nodeGetInfo): Adjust caller.
* tests/nodeinfotest.c (linuxTestCompareFiles): Likewise.
I got some spurious failures when commandhelper won the race and
ran to the point of parent detection prior to the intermediate
daemonizing process getting a chance to exit. This fixes it.
* tests/commandhelper.c (main): Checking for re-parenting to
init(1) is racy; instead check that we belong to a new session.
* tests/qemuhelpdata/qemu-kvm-0.13.0: New file.
* tests/qemuhelptest.c (mymain): New test from Fedora 14 qemu-kvm,
which covers some options (like -fstype passthrough) not tested elsewhere.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel60: New file.
* tests/qemuhelptest.c (mymain): New test from RHEL 6.0 qemu-kvm,
which covers some options (like -vga=qxl) not tested elsewhere.
* .x-sc_prohibit_empty_lines_at_EOF: Exempt qemu help output.
The xml watchdog dump option is converted to qemu watchdog pause arg
but it is not reasonable to convert it back from qemu watchdog pause
arg since there already is a xml watchdog pause option, so a test for
the dump option to convert it from arg to xml is not added.
Commit febc591683 introduced -vga none in
case no video card is included in domain XML. However, old qemu
versions do not support this and such domain cannot be successfully
started.
Guarantee that outbuf/errbuf are allocated on success, even if to the
empty string. Caller always has to free the result, and empty output
check requires checking if *outbuf=='\0'. Makes the API easier to use
safely. Failure is best effort allocation (some paths, like
out-of-memory, cannot allocate a buffer, but most do), so caller must
free buffer on failure.
* docs/internals/command.html.in: Update documentation.
* src/util/command.c (virCommandSetOutputBuffer)
(virCommandSetErrorBuffer, virCommandProcessIO) Guarantee empty
string on no output.
* tests/commandtest.c (test17): New test.
The log lists things like -smbios type=1,vendor="Red Hat", which
is great for shell parsing, but not so great when you realize that
execve() then passes those literal "" on as part of the command
line argument, such that qemu sets SMBIOS with extra literal quotes.
The eventual addition of virCommand is needed before we have the API
to shell-quote a string representation of a command line, so that the
log can still be pasted into a shell, but without inserting extra
bytes into the execve() arguments.
* src/qemu/qemu_conf.c (qemuBuildSmbiosBiosStr)
(qemuBuildSmbiosSystemStr): Qemu doesn't like quotes around uuid
arguments, and the remaining quotes are passed literally to
smbios, making <smbios mode='host'/> inaccurate. Removing the
quotes makes the log harder to parse, but that can be fixed later
with virCommand improvements.
* tests/qemuxml2argvdata/qemuxml2argv-smbios.args: 'Fix' test; it
will need fixing again once virCommand learns how to shell-quote a
potential command line.
* src/qemu/qemu_conf.c (qemudExtractVersionInfo): Check for file
before executing it here, rather than in callers.
(qemudBuildCommandLine): Rewrite with virCommand.
* src/qemu/qemu_conf.h (qemudBuildCommandLine): Update signature.
* src/qemu/qemu_driver.c (qemuAssignPCIAddresses)
(qemudStartVMDaemon, qemuDomainXMLToNative): Adjust callers.
This introduces a new set of APIs in src/util/command.h
to use for invoking commands. This is intended to replace
all current usage of virRun and virExec variants, with a
more flexible and less error prone API.
* src/util/command.c: New file.
* src/util/command.h: New header.
* src/Makefile.am (UTIL_SOURCES): Build it.
* src/libvirt_private.syms: Export symbols internally.
* tests/commandtest.c: New test.
* tests/Makefile.am (check_PROGRAMS): Run it.
* tests/commandhelper.c: Auxiliary program.
* tests/commanddata/test2.log - test15.log: New expected outputs.
* cfg.mk (useless_free_options): Add virCommandFree.
(msg_gen_function): Add virCommandError.
* po/POTFILES.in: New translation.
* .x-sc_avoid_write: Add exemption.
* tests/.gitignore: Ignore new built file.
This patch allows for using custom scripts instead of /usr/bin/qemu
emulator in domain XML. To do so, one would specify relative path to the
custom script in <emulator/>. The path needs to be relative to
qemuxml2argvdata directory and it will be transparently made absolute in
runtime. The expected command line needs to contain the exact relative
path as was used in domain XML.
The problem is RelaxNG schema for domain XML only allows for absolute
path within <emulator/>. To workaround it, an extra '/' must be added at
the beginning of the path. That is, instead of "./qemu.sh" or
"../emulator/qemu.sh" one would use "/./qemu.sh" or
"/../emulator/qemu.sh". The extra slash is removed before further
processing. I don't like this workaround, it's very ugly but it's the
best option I was able to come up with. Relaxing domain XML schema is
not an option IMO.
Without this fix, the test suite doesn't print error messages when a libvirt
function fails. Additionally, only print error reports if DEBUG or VERBOSE
requested.
Similarly to deprecating close(), I am now deprecating fclose() and
introduce VIR_FORCE_FCLOSE() and VIR_FCLOSE(). Also, fdopen() is replaced with
VIR_FDOPEN().
Most of the files are opened in read-only mode, so usage of
VIR_FORCE_CLOSE() seemed appropriate. Others that are opened in write
mode already had the fclose()< 0 check and I converted those to
VIR_FCLOSE()< 0.
I did not find occurrences of possible double-closed files on the way.
Using automated replacement with sed and editing I have now replaced all
occurrences of close() with VIR_(FORCE_)CLOSE() except for one, of
course. Some replacements were straight forward, others I needed to pay
attention. I hope I payed attention in all the right places... Please
have a look. This should have at least solved one more double-close
error.
* docs/schemas/domain.rng: Fix merge error which left SPICE channel
elements under VNC schema.
* tests/qemuhelptest.c: Add SPICE flag to kvm-83 test
* tests/qemuxml2argvdata/qemuxml2argv-graphics-spice.xml: Add
<memballoon> element
This extends the SPICE XML to allow channel security options
<graphics type='spice' port='-1' tlsPort='-1' autoport='yes'>
<channel name='main' mode='secure'/>
<channel name='record' mode='insecure'/>
</graphics>
Any non-specified channel uses the default, which allows both
secure & insecure usage
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/libvirt_private.syms: Add XML syntax for specifying per
channel security options for spice.
* src/qemu/qemu_conf.c: Configure channel security with spice
QEMU crashes & burns if you try multiple Cirrus video cards, but
QXL copes fine. Adapt QEMU config code to allow multiple QXL
video cards
* src/qemu/qemu_conf.c: Support multiple QXL video cards
In common with VNC, the QEMU driver configuration file is used
specify the host level TLS certificate location and a default
password / listen address
* src/qemu/qemu.conf: Add spice_listen, spice_tls,
spice_tls_x509_cert_dir & spice_password config params
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Parsing of
spice config parameters and updating -spice arg generation
to use them
* tests/qemuxml2argvdata/qemuxml2argv-graphics-spice-rhel6.args,
tests/qemuxml2argvtest.c: Expand test case to cover driver
level configuration
This supports the -spice argument posted for review against
the latest upstream QEMU/KVM. This supports the bare minimum
config with port, TLS port & listen address. The x509 bits are
added in a later patch.
* src/qemu_conf.c, src/qemu_conf.h: Add SPICE flag. Check for
-spice availability. Format -spice arg for command line
* qemuhelptest.c: Add SPICE flag
* qemuxml2argvdata/qemuxml2argv-graphics-spice.args: Add <graphics>
for spice
* qemuxml2argvdata/qemuxml2argv-graphics-spice.xml: Add -spice arg
* qemuxml2argvtest.c: Add SPICE flag
This supports the '-vga qxl' parameter in upstream QEMU/KVM
which has SPICE support added. This isn't particularly useful
until you get the next patch for -spice support. Also note that
while the libvirt XML supports multiple video devices, this
patch only supports a single one. A later patch can add support
for 2nd, 3rd, etc PCI devices for QXL
* src/qemu/qemu_conf.h: Flag for QXL support
* src/qemu/qemu_conf.c: Probe for '-vga qxl' support and implement it
* tests/qemuxml2argvtest.c, tests/qemuxml2xmltest.c,
tests/qemuxml2argvdata/qemuxml2argv-graphics-spice.args,
tests/qemuxml2argvdata/qemuxml2argv-graphics-spice.xml: Test
case for generating spice args with RHEL6 kvm
The patch is based on the possiblity in the QEmu command line to
add -smbios options allowing to override the default values picked
by QEmu. We need to detect this first from QEmu help output.
If the domain is defined with smbios to be inherited from host
then we pass the values coming from the Host own SMBIOS, but
if the domain is defined with smbios to come from sysinfo, we
use the ones coming from the domain definition.
* src/qemu/qemu_conf.h: add the QEMUD_CMD_FLAG_SMBIOS_TYPE enum
value
* src/qemu/qemu_conf.c: scan the help output for the smbios support,
and if available add support based on the domain definitions,
and host data
* tests/qemuhelptest.c: add the new enum in the outputs
libvirtd.conf uses "libvirt" as the value of "unix_sock_group",
however, group "libvirt" may not exist on the system, in this case
the case will always fail.
As a solution, replace "libvirt" with "$USER" in "tmp.conf".
When using 0-prefixed numbers, QEmu will interpret them as octal numbers
(as C convention says); this means that if you attach a device that has
addr > 10 (decimal) you're going to attach a different device.
So far, readonly=on option is used when qemu supports -device. However,
there are qemu versions which support readonly option with -drive
although they don't have support for -device.
Add a test suite for check parsing, formatting, range calculation
and netmask checking APIs in virSocketAddr.
* tests/sockettest.c, tests/Makefile.am: Add new test case
This sets the process name to the same value as the Windows title,
but since the name is limited to 16 chars only this is kept as a
configuration option and turned off by default
* src/qemu/qemu.conf src/qemu/qemu_conf.[ch]: hceck for support in the
QEmu help output, add the option in qemu conf file and augment
qemudBuildCommandLine to add it if switched on
* src/qemu/libvirtd_qemu.aug src/qemu/test_libvirtd_qemu.aug: augment
the augeas lenses accordingly
* tests/qemuhelptest.c: cope with the extra flag being detected now
The statstest is xen specific. Instead of filling the code with
a huge number of #ifdef WITH_XEN, just make its entire compilation
conditional in the Makefile.am. Also ensure it links to the Xen
driver so that it builds when driver modules are enabled
* tests/Makefile.am: Make statstest xen conditional. Link to
xen driver
* tests/Makefile.am: Remove all conditionals
This patch series focuses on xendConfigVersion 2 (xm_internal) and 3
(xend_internal), but leaves out changes for xenapi drivers.
See this link for more details about vcpu_avail for xm usage.
http://lists.xensource.com/archives/html/xen-devel/2009-11/msg01061.html
This relies on the fact that def->maxvcpus can be at most 32 with xen.
* src/xen/xend_internal.c (xenDaemonParseSxpr)
(sexpr_to_xend_domain_info, xenDaemonFormatSxpr): Use vcpu_avail
when current vcpus is less than maximum.
* src/xen/xm_internal.c (xenXMDomainConfigParse)
(xenXMDomainConfigFormat): Likewise.
* tests/xml2sexprdata/xml2sexpr-pv-vcpus.sexpr: New file.
* tests/sexpr2xmldata/sexpr2xml-pv-vcpus.sexpr: Likewise.
* tests/sexpr2xmldata/sexpr2xml-pv-vcpus.xml: Likewise.
* tests/xmconfigdata/test-paravirt-vcpu.cfg: Likewise.
* tests/xmconfigdata/test-paravirt-vcpu.xml: Likewise.
* tests/xml2sexprtest.c (mymain): New test.
* tests/sexpr2xmltest.c (mymain): Likewise.
* tests/xmconfigtest.c (mymain): Likewise.
* src/qemu/qemu_conf.c (qemuParseCommandLineSmp): Distinguish
between vcpus and maxvcpus, for new enough qemu.
* tests/qemuargv2xmltest.c (mymain): Add new test.
* tests/qemuxml2argvtest.c (mymain): Likewise.
* tests/qemuxml2xmltest.c (mymain): Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-smp.args: New file.
Syntax agreed on in
https://www.redhat.com/archives/libvir-list/2010-September/msg00476.html
<domain ...>
<vcpu current='x'>y</vcpu>
...
can now be used to specify 1 <= x <= y current vcpus, in relation
to the boot-time max of y vcpus. If current is omitted, then
current and max are assumed to be the same value.
* docs/schemas/domain.rng: Add new attribute.
* docs/formatdomain.html.in: Document it.
* tests/qemuxml2argvdata/qemuxml2argv-smp.xml: Add to
domainschematest.
* tests/xml2sexprdata/xml2sexpr-pv-vcpus.xml: Likewise.
ESX(i) uses UTF-8, but a Windows based GSX server writes
Windows-1252 encoded VMX files.
Add a test case to ensure that libxml2 provides Windows-1252
to UTF-8 conversion.
This enables support for nested SVM using the regular CPU
model/features block. If the CPU model or features include
'svm', then the '-enable-nesting' flag will be added to the
QEMU command line. Latest out of tree patches for nested
'vmx', no longer require the '-enable-nesting' flag. They
instead just look at the cpu features. Several of the models
already include svm support, but QEMU was just masking out
the svm bit silently. So this will enable SVM on such
models
* src/qemu/qemu_conf.h: flag for -enable-nesting
* src/qemu/qemu_conf.c: Use -enable-nesting if VMX or SVM are in
the CPUID
* src/cpu/cpu.h, src/cpu/cpu.c: API to check for a named feature
* src/cpu/cpu_x86.c: x86 impl of feature check
* src/libvirt_private.syms: Add cpuHasFeature
* src/qemuhelptest.c: Add nesting flag where required
Before running each test case clear the thread local error
indicator. After running each test case, dispatch any error
that was reported
* tests/testutils.c: Fix error reporting in test suites
* src/xen/sexpr.c: Ensure () are escaped in sexpr2string
* tests/sexpr2xmldata/sexpr2xml-boot-grub.sexpr,
tests/sexpr2xmldata/sexpr2xml-boot-grub.xml,
tests/xml2sexprdata/xml2sexpr-boot-grub.sexpr,
tests/xml2sexprdata/xml2sexpr-boot-grub.xml: Data files to
check escaping
* tests/sexpr2xmltest.c, tests/xml2sexprtest.c: Add boot-grub
escaping test case
Make use of the existing <filesystem> element to support plan9fs
filesystem passthrough in the QEMU driver
<filesystem type='mount'>
<source dir='/export/to/guest'/>
<target dir='/import/from/host'/>
</filesystem>
NB, the target is not actually a directory, it is merely a arbitrary
string tag that is exported to the guest as a hint for where to mount
it.
Adding parsing code for memory tunables in the domain xml file
also change the internal define structures used for domain memory
informations
Adds a new specific test
This patch adds a test case for testing the XML parser's and instantiator's
support of the state attribute. The other test case tests existing
capabilities. Both test cases will be used in TCK again.
Since version 4.1 ESX(i) can expose virtual serial devices over TCP.
Add support in the VMX handling code for this, add test cases to cover
it and add links to some documentation.
ESX supports two additional protocols: TELNETS and TLS. Add them to
the list of serial-over-TCP protocols.
Description: Implement AppArmorSetSecurityHostdevLabel() and
AppArmorRestoreSecurityHostdevLabel() for hostdev and pcidev attach.
virt-aa-helper also has to be adjusted because *FileIterate() is used for pci
and usb devices and the corresponding XML for hot attached hostdev and pcidev
is not in the XML passed to virt-aa-helper. The new '-F filename' option is
added to append a rule to the profile as opposed to the existing '-f
filename', which rewrites the libvirt-<uuid>.files file anew. This new '-F'
option will append a rule to an existing libvirt-<uuid>.files if it exists,
otherwise it acts the same as '-f'.
load_profile() and reload_profile() have been adjusted to add an 'append'
argument, which when true will use '-F' instead of '-f' when executing
virt-aa-helper.
All existing calls to load_profile() and reload_profile() have been adjusted
to use the old behavior (ie append==false) except AppArmorSetSavedStateLabel()
where it made sense to use the new behavior.
This patch also adds tests for '-F'.
Bug-Ubuntu: https://bugs.launchpad.net/ubuntu/+source/libvirt/+bug/640993
Description: Check for VIR_DOMAIN_CHR_TYPE in serial ports and add 'rw' for
defined serial ports, parallel ports and channels
Bug-Ubuntu: LP: #578527, LP: #609055
Before this patch, the testsuite was noisy:
TEST: qemuargv2xmltest
........................................ 40
................20:41:28.046: warning : qemuParseCommandLine:6565 : unknown QEMU argument '-unknown', adding to the qemu namespace
20:41:28.046: warning : qemuParseCommandLine:6565 : unknown QEMU argument 'parameter', adding to the qemu namespace
. 57 OK
PASS: qemuargv2xmltest
It's not a real failure (which is why the test was completing
successfully), so much as an intentional warning to the user that use
of the qemu namespace has the potential for undefined effects that
leaked through the default logging behavior. After this patch series,
all tests can access any logged data, and this particular test can
explicitly check for the presence or absence of the warning, such that
the test output becomes:
TEST: qemuargv2xmltest
........................................ 40
................. 57 OK
PASS: qemuargv2xmltest
* tests/testutils.h (virtTestLogContentAndReset): New prototype.
* tests/testutils.c (struct virtTestLogData): New struct.
(virtTestLogOutput, virtTestLogClose, virtTestLogContentAndReset):
New functions.
(virtTestMain): Always capture log data emitted during tests.
* tests/qemuargv2xmltest.c (testCompareXMLToArgvHelper, mymain):
Use flag to mark which tests expect noisy stderr.
(testCompareXMLToArgvFiles): Add parameter to test whether stderr
was appropriately silent.
* src/Makefile.am (libvirt.def, libvirt_qemu.def): '\}' and '\t'
are not required by POSIX. Use '}' and literal tab instead.
(install-data-local): Avoid sed -i.
* tests/read-bufsiz: Likewise.
Reported by Mitchell Hashimoto.
The current code will go into an infinite loop if the printf generated
string is >= 1000, AND exactly 1 character smaller than the amount of free
space in the buffer. When this happens, we are dropped into the loop body,
but nothing will actually change, because count == (buf->size - buf->use - 1),
and virBufferGrow returns unchanged if count < (buf->size - buf->use)
Fix this by removing the '- 1' bit from 'size'. The *nprintf functions handle
the NULL byte for us anyways, so we shouldn't need to manually accommodate
for it.
Here's a bug where we are actually hitting this issue:
https://bugzilla.redhat.com/show_bug.cgi?id=602772
v2: Eric's improvements: while -> if (), remove extra va_list variable,
make sure we report buffer error if snprintf fails
v3: Add tests/virbuftest which reproduces the infinite loop before this
patch, works correctly after
Instead of splitting the path part of a datastore path into
directory and file name, keep this in one piece. An example:
"[datastore] directory/file"
was split into this before:
datastoreName = "datastore"
directoryName = "directory"
fileName = "file"
Now it's split into this:
datastoreName = "datastore"
directoryName = "directory"
directoryAndFileName = "directory/file"
This simplifies code using esxUtil_ParseDatastorePath, because
directoryAndFileName is used more often than fileName. Also the
old approach expected the datastore path to reference an actual
file, but this isn't always correct, especially when listing
volumes. In that case esxUtil_ParseDatastorePath is used to parse
a path that references a directory. This fails for a vpx://
connection because the vCenter returns directory paths with a
trailing '/'. The new approach is robust against this and the
actual decision if the datastore path should reference a file or
a directory is up to the caller of esxUtil_ParseDatastorePath.
Update the tests accordingly.
RHEL-5 Xen doesn't support the old style vnc configuration. In sexpr, we
can't really check it with rhel5-api turned on. However, for XM
configuration files it's sufficient to use cfg version 1 instead of 2.
The most common cause of errors with rhel5-api turn on was missing
"(type ioemu)" in sexpr or its equivalent in XM configuration file. This
happens because the presence of that part in sexpr (or cfg) depends on
xen version the host is running. Let's avoid it by explicitly specifying
interface model which ensures "type ioemu" will always be emitted.
This patch adds
<model type='e1000'/>
withing the interface element in all affected xml files. And
(model 'e1000')
to all corresponding sexpr files with similar fix to cfg files. Such
configuration works regardless on Xen version.
I wrote a patch to add support for listing the Vendor and Model of a
storage pool in the storage pool XML. This would allow vendor
extensions of specific devices. The patch includes a test for the new
attributes as well.
Patrick Dignan
floppy0.present defaults to true. Therefore, it needs to be
explicitly set to false when the XML config doesn't specify the
corresponding floppy device.
Also update tests accordingly.
Introduce esxVMX_Context containing functions pointers to
glue both parts together in a generic way.
Move the ESX specific part to esx_driver.c.
This is a step towards making the VMX code reusable in a
potential VMware Workstation and VMware Player driver.
According to <xen-3.4.3/tools/python/xen/xm/create.py:158>
gopts.var('bootargs', val='NAME',
fn=set_value, default=None,
use="Arguments to pass to boot loader")
the "bootloader_args" parameter needs to be translated into "bootargs"
when using "virsh domxml-to-native xen-xm".
The reverse direction (domxml-from-native) is already okay.
This patch fixes domxml-to-native and adds two test files to catch this
problem.
Signed-off-by: Philipp Hahn <hahn@univention.de>
the followup on the boot=on problem, basically it's not needed to
specify it when booting out of IDE devices when using KVM
* src/qemu/qemu_conf.c: do not use boot=on for IDE devices
* tests/qemuxml2argvdata/qemuxml2argv*.args: this changes the output
for 5 of the tests
Don't rely on summary.url anymore, because its value is different
between an esx:// and vpx:// connection. Use host.mountInfo.path
instead.
Don't fallback to lookup by UUID (actually lookup by absolute path)
in esxVI_LookupDatastoreByName when lookup by name fails. Add a
seperate function for this: esxVI_LookupDatastoreByAbsolutePath
'./autobuild.sh' with lcov installed discovered that our
coverage support has been bit-rotting for a while. This
restores it back to a successful state, although I have
not yet spent any time looking through the resulting files to
look for low-hanging fruit in the unit test coverage front.
* configure.ac: Clear COMPILER_FLAGS at right place.
* Makefile.am (cov): Newer genhtml no longer likes plain -s.
* m4/compiler-flags.m4 (gl_COMPILER_FLAGS): Don't AC_SUBST
COMPILER_FLAGS; it is a shell variable for use in configure only.
* src/Makefile.am (AM_CFLAGS, AM_LDFLAGS): New variables, to make
it easier to provide global flag additions. Use throughout, to
uniformly apply coverage flags.
* .gitignore: Globally ignore gcov output.
* daemon/.gitignore: Simplify.
* src/.gitignore: Likewise.
* tests/.gitignore: Likewise.
All <console> devices now export a <target> type attribute. QEMU defaults
to 'serial', UML defaults to 'uml, xen can be either 'serial' or 'xen'
depending on fullvirt. Understandably there is lots of test fallout.
This will be used to differentiate between a serial vs. virtio console for
QEMU.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Add tests for auto memballon, implicit IDE, SCSI, virtio channel
controllers, and console/serial back compat.
Additionally, an explicit qemuxml2argvtest for scsi disks is added.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Add a new element to the <os> block:
<bootmenu enable="yes|no"/>
Which maps to -boot,menu=on|off on the QEMU command line.
I decided to use an explicit 'enable' attribute rather than just make the
bootmenu element boolean. This allows us to treat lack of a bootmenu element
as 'use hypervisor default'.
Commit 68719c4bdd added the disk format
probing option. This makes virt-aa-helper-test fail because the domain
config didn't specifiy the disk format and it didn't pass '-p 1' to
virt-aa-helper to allow disk format probing.
Specify the disk format in the domain config. Pass the '-p 1' option
to virt-aa-helper for the test case with two disks. This way this test
also covers this new option.
Thanks to DV for knocking together the Relax-NG changes
quickly for me.
Changes since v1:
- Change the domain.rng to correspond to the new schema
- Don't allocate caps->ns in testQemuCapsInit since it is a static table
Changes since v2:
- Change domain.rng to add restrictions on allowed environment names
Changes since v3:
- Remove a bogus comment in the tests
Signed-off-by: Chris Lalancette <clalance@redhat.com>
To try and ensure that people upgrading from old QEMU get guests
with the same PCI device ordering, change the way we assign addrs
to match QEMU's default order. This should make Windows less
annoyed.
* src/qemu/qemu_conf.c: Follow QEMU's default PCI ordering
logic when assigning addresses
* tests/*.args: Update for changed PCI addresses
To allow compatibility with older QEMU PCI device slot assignment
it is necessary to explicitly track the balloon device in the
XML. This introduces a new device
<memballoon model='virtio|xen'/>
It can also have a PCI address, auto-assigned if necessary.
The memballoon will be automatically added to all Xen and QEMU
guests by default.
* docs/schemas/domain.rng: Add <memballoon> element
* src/conf/domain_conf.c, src/conf/domain_conf.h: parsing
and formatting for memballoon device. Always add a memory
balloon device to Xen/QEMU if none exists in XML
* src/libvirt_private.syms: Export memballoon model APIs
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Honour the
PCI device address in memory balloon device
* tests/*: Update to test new functionality
Disk format probing is now disabled by default. A new config
option in /etc/qemu/qemu.conf will re-enable it for existing
deployments where this causes trouble
By specifying <vendor> element in CPU requirements a guest can be
restricted to run only on CPUs by a given vendor. Host CPU vendor is
also specified in capabilities XML.
The vendor is checked when migrating a guest but it's not forced, i.e.,
guests configured without <vendor> element can be freely migrated.
The previous change which split -nodefconfig probing off
from -device broke the test case because it missed adding
the QEMUD_CMD_FLAG_NODEFCONFIG to the test
* src/util/bridge.c: Set QEMUD_CMD_FLAG_NODEFCONFIG for all
configs with QEMUD_CMD_FLAG_DEVICE set
Also don't abuse the disk driver name to specify the SCSI controller
model anymore:
<driver name='buslogic'/>
Use the newly added model attribute of the controller element for this:
<controller type='scsi' index='0' model='buslogic'/>
The disk driver name approach is deprecated now, but still works for
backward compatibility reasons.
Update the documentation and tests accordingly.
Fix usage of the words controller and id in the VMX handling code. Use
controller, bus and unit properly.
We already use the '-nodefaults' command line arg with QEMU to stop
it adding any default devices to guests. Unfortunately, QEMU will
load global config files from /etc/qemu that may also add default
devices. These aren't blocked by '-nodefaults', so we need to also
add the '-nodefconfig' arg to prevent that.
Unfortunately these global config files are also used to define
custom CPU models. So in blocking global hardware device addition
we also block definitions of new CPU models. Libvirt doesn't know
about these custom CPU models though, so it would never make use
of them anyway. Thus blocking them via -nodefconfig isn't a show
stopping problem. We would need to expand libvirt's own CPU model
XML database to support these instead.
* src/qemu/qemu_conf.c: Add '-nodefconfig' if available
* tests/qemuxml2argvdata/: Add '-nodefconfig' to all data files which
have '-nodefaults' present
This patch adds an optional XML attribute to a nwfilter rule to give the user control over whether the rule is supposed to be using the iptables state match or not. A rule may now look like shown in the XML below with the statematch attribute either having value '0' or 'false' (case-insensitive).
[...]
<rule action='accept' direction='in' statematch='false'>
<tcp srcmacaddr='1:2:3:4:5:6'
srcipaddr='10.1.2.3' srcipmask='32'
dscp='33'
srcportstart='20' srcportend='21'
dstportstart='100' dstportend='1111'/>
</rule>
[...]
I am also extending the nwfilter schema and add this attribute to a test case.
This patch adds the persistence status (yes/no) to the output of the virsh
dominfo and pool-info commands. This patch also adds the autostart status
to the output of the virsh pool-info command.
Red Hat BZ for this:
https://bugzilla.redhat.com/show_bug.cgi?id=603696
The virtio serial changes broke the test suite because they forgot
to add the new address attribute to the domain XML schema. The
xml2xml test also broke because the XML no longer roundtrips. This
is due to testing of auto-addition of <controller> elements. Split
that test case off into a separate XML file to avoid breakage
* docs/schemas/domain.rng: Allow port number for virtio serial addresses
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: Revert to
a simple config to avoid breaking xml2xml test
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.xml,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.args: Add
complex test case for auto-controller addition for xml2argv test
* tests/qemuxml2argvtest.c: Add channel-virtio-auto test
The domain parsing code would auto-add a virtio serial controller
if it saw any virtio serial channel defined. Unfortunately it
always added a controller with index=0, even if the channel address
specified an index != 0. It only added one controller, even if
multiple controllers were referenced by channels. Finally, it let
the ports+vectors parameters initialize to zero instead of -1, which
prevented the controllers accepting any ports.
* src/conf/domain_conf.c: Initialize ports+vectors when adding
virtio serial controllers. Add all neccessary virtio serial
controllers, instead of hardcoding controller 0
* qemuxml2argvdata/qemuxml2argv-channel-virtio.args,
qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: Expand to
test controller auto-add behaviour
To ensure that the device addressing scheme is stable across
hotplug/unplug, all virtio serial channels needs to have an
associated port number in their address. This is then specified
to QEMU using the nr=NNN parameter
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parsing
for port number in vioserial address types.
* src/qemu/qemu_conf.c: Set 'nr=NNN' parameter with virtio
serial port number
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: Expand
data set to ensure coverage of port addressing
'listen' isn't a valid qemu-dm option, as reported a long time ago here:
https://bugzilla.redhat.com/show_bug.cgi?id=492958
Matches the near identical logic in qemu_conf.c
v2: When parsing sexpr, only match on ",server", rather than
full ',server,nowait'.
* tests/daemon-conf: Accommodate the fact that out template,
daemon/libvirtd.conf now contains an invalid host_uuid.
Convert it to a valid one before the final libvirtd-running
test that must terminate normally.
This patch parses the following two XML descriptions, one for
802.1Qbg and one for 802.1Qbh, and stores the data internally.
The actual triggering of the switch setup protocol has not been
implemented here but the relevant code to do that should go into
the functions associatePortProfileId() and disassociatePortProfileId().
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbg'>
<parameters managerid='12' typeid='0x123456' typeidversion='1'
instanceid='fa9b7fff-b0a0-4893-8e0e-beef4ff18f8f'/>
</virtualport>
<filterref filter='clean-traffic'/>
</interface>
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbh'>
<parameters profileid='my_profile'/>
</virtualport>
</interface>
I'd suggest to use this patch as a base for triggering the setup
protocol with the 802.1Qb{g|h} switch.
Several rounds of changes were made to this patch. The
following is a list of these changes.
- Renamed structure virVirtualPortProfileDef to virVirtualPortProfileParams
as per Daniel Berrange's request
- Addressing Daniel Berrange's comments:
- removing macvtap.h's dependency on domain_conf.h by
moving the virVirtualPortProfileDef structure into macvtap.h
and not passing virtDomainNetDefPtr to any functions in
macvtap.c
- Addressed most of Chris Wright's comments:
- indicating error in case virtualport XML node cannot be parsed
properly
- parsing hex and decimal numbers using virStrToLong_ui() with
parameter '0' for base
- tgifname (target interface name) variable wasn't necessary
to pass to openMacvtapTap function anymore
- assigning the virtual port data structure to the virDomainNetDef
only if it was previously parsed
- make sure that the error code returned by openMacvtapTap() is a negative n
in case the associatePortProfileId() function failed.
- renaming vsi in the XML to virtualport
- replace all occurrences of vsi in the source as well
- removing mode and MAC address parameters from the functions that
will communicate with the hareware diretctly or indirectly
- moving the associate and disassociate functions to the end of the
file for subsequent patches to easier make them generally available
for export
- passing the macvtap interface name rather than the link device since
this otherwise gives funny side effects when using netlink messages
where IFLA_IFNAME and IFLA_ADDRESS are specified and the link dev
all of a sudden gets the MAC address of the macvtap interface.
- Removing rc = -1 error indications in the case of 802.1Qbg|h setup in case
we wanted to use hook scripts for the setup and so the setup doesn't fail
here.
- if instance ID UUID is not supplied it will automatically be generated
- adapted schema to make instance ID UUID optional
- added test case
- parser and XML generator have been separated into their own
functions so they can be re-used elsewhere (passthrough case
for example)
- Adapted XML parser and generator support the above shown type
(802.1Qbg, 802.1Qbh).
- Adapted schema to above XML
- Adapted test XML to above XML
- Passing through the VM's UUID which seems to be necessary for
802.1Qbh -- sorry no host UUID
- adding virtual function ID to association function, in case it's
necessary to use (for SR-IOV)
Spurious / in a pool target path makes life difficult for apps using the
GetVolByPath, and doing other path based comparisons with pools. This
has caused a few issues for virt-manager users:
https://bugzilla.redhat.com/show_bug.cgi?id=494005https://bugzilla.redhat.com/show_bug.cgi?id=593565
Add a new util API which removes spurious /, virFileSanitizePath. Sanitize
target paths when parsing pool XML, and for paths passed to GetVolByPath.
v2: Leading // must be preserved, properly sanitize path=/, sanitize
away /./ -> /
v3: Properly handle starting ./ and ending /.
v4: Drop all '.' handling, just sanitize / for now.
Allow for a host UUID in the capabilities XML. Local drivers
will initialize this from the SMBIOS data. If a sanity check
shows SMBIOS uuid is invalid, allow an override from the
libvirtd.conf configuration file
* daemon/libvirtd.c, daemon/libvirtd.conf: Support a host_uuid
configuration option
* docs/schemas/capability.rng: Add optional host uuid field
* src/conf/capabilities.c, src/conf/capabilities.h: Include
host UUID in XML
* src/libvirt_private.syms: Export new uuid.h functions
* src/lxc/lxc_conf.c, src/qemu/qemu_driver.c,
src/uml/uml_conf.c: Set host UUID in capabilities
* src/util/uuid.c, src/util/uuid.h: Support for host UUIDs
* src/node_device/node_device_udev.c: Use the host UUID functions
* tests/confdata/libvirtd.conf, tests/confdata/libvirtd.out: Add
new host_uuid config option to test
* tests/nodeinfotest.c (linuxTestCompareFiles): Don't use
nodeinfo->member uninitialized. linuxNodeInfoCPUPopulate requires
that some of its nodeinfo members (including threads) be initialized
upon input. The nodeinfotest.c program lacked the initialization,
while the only other use (nodeGetInfo) did perform it.
It's not trivial to move the initialization into the function,
since nodeGetInfo sets at least one member after clearing the
buffer but before calling linuxNodeInfoCPUPopulate.
(gdb) p/x QEMUD_CMD_FLAG_VNET_HOST
$7 = 0xffffffff80000000
Oops - that meant we were incorrectly setting QEMU_CMD_FLAG_RTC_TD_HACK
for qemu-kvm-0.12.3 (and probably botching a few other settings as well).
Fixes Red Hat BZ#592070
* src/qemu/qemu_conf.h (QEMUD_CMD_FLAG_VNET_HOST): Avoid sign
extension.
* tests/qemuhelpdata/qemu-kvm-0.12.3: New file.
* tests/qemuhelptest.c (mymain): Add another case.
The max path length for unix sockets is pretty small (108, see man 7 unix).
If 'make check' is run from a directory that exceeds this, one of the tests
will fail, and in such a way that requires manually editting the test to
determine why.
There are certainly other ways to handle this, but I've chosen just to skip
the offending test if we will exceed the length limitation.
v2: Drop bashism, use test infrastructure to warn and skip
* tests/virsh-schedinfo: This test sets PATH internally, just in
case you're running it manually. Normally, the PATH setting from
tests/Makefile.am's TESTS_ENVIRONMENT is sufficient. Prepend the
correct directory, and take advantage of the PATH setting in one
more case.
For example, virsh -c test:///default schedinfo 1 --set P=k would
mistakenly exit successfully, giving no indication that it had failed
to set the scheduling parameter "P".
* tools/virsh.c (cmdSchedinfo): Diagnose an invalid --set j=k option,
rather than silently ignoring it.
* tests/virsh-schedinfo: New test for the above.
* tests/Makefile.am (test_scripts): Add it.
Reported by Jintao Yang in http://bugzilla.redhat.com/586632
This patch adds support for the RARP protocol. This may be needed due to
qemu sending out a RARP packet (at least that's what it seems to want to
do even though the protocol id is wrong) when migration finishes and
we'd need a rule to let the packets pass.
Unfortunately my installation of ebtables does not understand -p RARP
and also seems to otherwise depend on strings in /etc/ethertype
translated to protocol identifiers. Therefore I need to pass -p 0x8035
for RARP. To generally get rid of the dependency of that file I switch
all so far supported protocols to use their protocol identifier in the
-p parameter rather than the string.
I am also extending the schema and added a test case.
changes from v1 to v2:
- added test case into patch
* virStorageEncryptionFormat is called from both
virDomainDiskDefFormat and virStorageVolTargetDefFormat. The proper
indentation in the generated XML depends on the caller. My earlier
patch to fix the incorrect indentation for the domain XML broke the
indentation for the storage XML. This patch adopts Laine's
suggestion of requring the caller of virStorageEncryptionFormat to
provide an unsigned int with the number of spaces the output should
be indented. The patch modifies both callers to provide the
additional argument.
* Add a regression test for the domain XML
* src/conf/domain_conf.c src/conf/storage_conf.c
src/conf/storage_encryption_conf.c src/conf/storage_encryption_conf.h:
change the indentation code
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-encrypted-disk.args
tests/qemuxml2argvdata/qemuxml2argv-encrypted-disk.xml: add a regression test
With this patch I want to enable hex number inputs in the filter XML. A
number that was entered as hex is also printed as hex unless a string
representing the meaning can be found.
I am also extending the schema and adding a test case. A problem with
the DSCP value is fixed on the way as well.
Changes from V1 to V2:
- using asHex boolean in all printf type of functions to select the
output format in hex or decimal format
The nodeinfotest was reliant on the host NUMA topology, but all
the test data files assumed 1 single NUMA node. This test thus
failed on any NUMA machine with > 1 node
* tests/nodeinfotest.c: Hardcode 1 single numa node
Fix invalid code generating in esx_vi_generator.py regarding deep copy
types that contain enum properties.
Add strptime and timegm to bootstrap.conf. Both are used to convert a
xsd:dateTime to calendar time.
Add a testcase of the xsd:dateTime conversion.
Extend tests to cover all SCSI controller types and document the
new type.
The lsisas1068 SCSI controller type was added in ESX 4.0. The VMX
parser reports an error when this controller type is present. This
makes virsh dumpxml fail for every domain that uses this controller
type.
This patch fixes this and adds lsisas1068 to the list of accepted
SCSI controller types.
Reported by Jonathan Kelley.
This patch implements support for learning a VM's IP address. It uses
the pcap library to listen on the VM's backend network interface (tap)
or the physical ethernet device (macvtap) and tries to capture packets
with source or destination MAC address of the VM and learn from DHCP
Offers, ARP traffic, or first-sent IPv4 packet what the IP address of
the VM's interface is. This then allows to instantiate the network
traffic filtering rules without the user having to provide the IP
parameter somewhere in the filter description or in the interface
description as a parameter. This only supports to detect the parameter
IP, which is for the assumed single IPv4 address of a VM. There is not
support for interfaces that may have multiple IP addresses (IP
aliasing) or IPv6 that may then require more than one valid IP address
to be detected. A VM can have multiple independent interfaces that each
uses a different IP address and in that case it will be attempted to
detect each one of the address independently.
So, when for example an interface description in the domain XML has
looked like this up to now:
<interface type='bridge'>
<source bridge='mybridge'/>
<model type='virtio'/>
<filterref filter='clean-traffic'>
<parameter name='IP' value='10.2.3.4'/>
</filterref>
</interface>
you may omit the IP parameter:
<interface type='bridge'>
<source bridge='mybridge'/>
<model type='virtio'/>
<filterref filter='clean-traffic'/>
</interface>
Internally I am walking the 'tree' of a VM's referenced network filters
and determine with the given variables which variables are missing. Now,
the above IP parameter may be missing and this causes a libvirt-internal
thread to be started that uses the pcap library's API to listen to the
backend interface (in case of macvtap to the physical interface) in an
attempt to determine the missing IP parameter. If the backend interface
disappears the thread terminates assuming the VM was brought down. In
case of a macvtap device a timeout is being used to wait for packets
from the given VM (filtering by VM's interface MAC address). If the VM's
macvtap device disappeared the thread also terminates. In all other
cases it tries to determine the IP address of the VM and will then apply
the rules late on the given interface, which would have happened
immediately if the IP parameter had been explicitly given. In case an
error happens while the firewall rules are applied, the VM's backend
interface is 'down'ed preventing it to communicate. Reasons for failure
for applying the network firewall rules may that an ebtables/iptables
command failes or OOM errors. Essentially the same failure reasons may
occur as when the firewall rules are applied immediately on VM start,
except that due to the late application of the filtering rules the VM
now is already running and cannot be hindered anymore from starting.
Bringing down the whole VM would probably be considered too drastic.
While a VM's IP address is attempted to be determined only limited
updates to network filters are allowed. In particular it is prevented
that filters are modified in such a way that they would introduce new
variables.
A caveat: The algorithm does not know which one is the appropriate IP
address of a VM. If the VM spoofs an IP address in its first ARP traffic
or IPv4 packets its filtering rules will be instantiated for this IP
address, thus 'locking' it to the found IP address. So, it's still
'safer' to explicitly provide the IP address of a VM's interface in the
filter description if it is known beforehand.
* configure.ac: detect libpcap
* libvirt.spec.in: require libpcap[-devel] if qemu is built
* src/internal.h: add the new ATTRIBUTE_PACKED define
* src/Makefile.am src/libvirt_private.syms: add the new modules and symbols
* src/nwfilter/nwfilter_learnipaddr.[ch]: new module being added
* src/nwfilter/nwfilter_driver.c src/conf/nwfilter_conf.[ch]
src/nwfilter/nwfilter_ebiptables_driver.[ch]
src/nwfilter/nwfilter_gentech_driver.[ch]: plu the new functionality in
* tests/nwfilterxml2xmltest: extend testing
This patch adds a relaxng nwfilter schema along with a test that
verifies all the test output XML against the schema. The input XMLs
contain a lot of intentional out-of-range values that make them fail the
schema verification, so I am not verifying against those.
A lot of syntax check rules have to be rewritten, but the
result is easier to maintain. I tested each syntax rule
by intentionally introducing a temporary violation of the rule.
Additionally, some false positives for unmarked_diagnostics
crept in, and an improved copyright_format test caught some bugs.
* .gnulib: Update to latest.
* cfg.mk (sc_prohibit_test_minus_ao): Delete, it was moved into
gnulib's maint.mk.
(sc_avoid_write, sc_prohibit_strcmp_and_strncmp)
(sc_prohibit_asprintf, sc_prohibit_strncpy, sc_prohibit_readlink)
(sc_prohibit_gethostname, sc_prohibit_gettext_noop)
(sc_prohibit_VIR_ERR_NO_MEMORY, sc_prohibit_nonreentrant)
(sc_prohibit_ctype_h, sc_TAB_in_indentation)
(sc_avoid_ctype_macros)
(sc_prohibit_virBufferAdd_with_string_literal)
(sc_prohibit_gethostby, sc_copyright_format): Rewrite in terms of
new maint.mk macros.
(sc_libvirt_unmarked_diagnostics): Fix whitespace.
* .x-sc_unmarked_diagnostics: New file.
* tests/object-locking.ml: Fix copyright.
* tools/virt-pki-validate.in: Likewise.
* tools/virt-xml-validate.in: Likewise.
* src/qemu/qemu_conf.h: define 4 new flags
* src/qemu/qemu_conf.c: check the help text of qemu for presence of
features indicated by each flag.
* tests/qemuhelptest.c: add appropriate flags into the masks for each test
* Fixes per feedback from Dan and Daniel
* Added test datafiles
* Re-disabled JSON flags
* Added code to print the error policy attribute when generating XML
* Re-add empty tag
The keys of entries in a VMX file are case insensitive. Both scsi0:1.fileName
and scsi0:1.filename are valid. Therefore, make the conf parser compare names
case insensitive in VMX mode to accept every capitalization variation.
Also add test cases for this.
* tests/test-lib.sh: "echo -n" is not portable. Use printf instead.
Remove unnecessary uses of "eval-in-subshell" (subshell is sufficient).
Remove uses of tests' -a operator; it is not portable.
Instead, use "test cond && test cond2".
* tests/schematestutils.sh: Replace use of test's -a.
This change only affects the output of tests that have an exact
multiple of 40 test cases. For example the domainschematest currently:
TEST: domainschematest
........................................ 40
........................................ 80
........................................ 120
........................................ 160
........................................ 200 OK
PASS: domainschematest
It outputs additional 40 spaces on the last line.
The domainschematest output is fixed by the change in test-lib.sh. The
change in testutils.c fixes this for tests written in C. Currently no
C test has an exact multiple of 40 test cases, but I checked it and
the same problem exists there.
This patch stops that in both cases.
* src/qemu/qemu_conf.c: add the ",readonly=on" for read-only disks
and also parse it back in qemuParseCommandLineDisk()
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.args
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.xml:
add a specific regression test
The current code for "nodeinfo" is pretty naive
about socket and thread information. To determine the
sockets, it just takes the number of cpus and divides
by the number of cores. For the thread count, it always
sets it to 1. With more recent Intel machines, however,
hyperthreading is again an option, meaning that these
heuristics no longer work and give bogus numbers. This
patch goes through /sys to get the additional
information so we properly report it.
Note that I had to edit the tests not to report on
socket and thread counts, since these are determined
dynamically now.
v2: As pointed out by Eric Blake, gnulib provides
count-one-bits (which is LGPLv2+). Use it instead
of a hand-coded popcnt.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Allow an arbitrary timezone with QEMU by setting the $TZ environment
variable when launching QEMU
* src/qemu/qemu_conf.c: Set TZ environment variable if a timezone
is requested
* tests/qemuxml2argvtest.c: Add test case for timezones
* tests/qemuxml2argvdata/qemuxml2argv-clock-france.xml,
tests/qemuxml2argvdata/qemuxml2argv-clock-france.args: Data
for timezone tests
This allows QEMU guests to be started with an arbitrary clock
offset
The test case can't actually be enabled, since QEMU argv expects
an absolute timestring, and this will obviously change every
time the test runs :-( Hopefully QEMU will allow a relative
time offset in the future.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Use the -rtc arg
if available to support variable clock offset mode
* tests/qemuhelptest.c: Add QEMUD_CMD_FLAG_RTC for qemu 0.12.1
* qemuxml2argvdata/qemuxml2argv-clock-variable.args,
qemuxml2argvdata/qemuxml2argv-clock-variable.xml,
qemuxml2argvtest.c: Test case, except we can't actually enable
it yet.
The daemon-conf test would fail on my system if there was a system libvirtd
running. In the course of troubleshooting that problem, I discovered that the
daemon-conf script would always fail if run by itself because it found the line:
\# that each "PARAMETER = VALUE" line in this file have the parameter
which it mistook for a line containing a parameter. I have changed the test to
avoid mistaking a line containing \"PARAMETER = VALUE\" for a parameter line.
The corrupted config tests turned out to be failing because the test daemon was
discovering the pid file from the running daemon and exiting before it processed
the test config file. Specifying the pid file for the corrupt config tests in
the same way as for the valid config test solved that problem.
Support virtio-serial controller and virtio channel in QEMU backend.
Will output
the following for virtio-serial controller:
-device
virtio-serial-pci,id=virtio-serial0,bus=pci.0,addr=0x4,max_ports=16,vectors=4
and the following for a virtio channel:
-chardev pty,id=channel0 \
-device
virtserialport,bus=virtio-serial0.0,chardev=channel0,name=org.linux-kvm.port.0
* src/qemu/qemu_conf.c: Add argument output for virtio
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args: Add test for
QEMU command line generation
Add support for virtio-serial by defining a new 'virtio' channel target type
and a virtio-serial controller. Allows the following to be specified in a
domain:
<controller type='virtio-serial' index='0' ports='16' vectors='4'/>
<channel type='pty'>
<target type='virtio' name='org.linux-kvm.port.0'/>
<address type='virtio-serial' controller='0' bus='0'/>
</channel>
* docs/schemas/domain.rng: Add virtio-serial controller and virtio
channel type.
* src/conf/domain_conf.[ch]: Domain parsing/serialization for
virtio-serial controller and virtio channel.
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: add domain xml
parsing test
* src/libvirt_private.syms src/qemu/qemu_conf.c:
virDomainDefAddDiskControllers() renamed to
virDomainDefAddImplicitControllers()
Use the ATTRIBUTE_NONNULL annotation to mark some virConnectPtr
args as mandatory non-null so the compiler can warn of mistakes
* src/conf/domain_event.h: All virConnectPtr args must be non-null
* src/qemu/qemu_conf.h: qemudBuildCommandLine and
qemudNetworkIfaceConnect() must be given non-null connection
* tests/qemuxml2argvtest.c: Provide a non-null (dummy) connection to
qemudBuildCommandLine()
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in interface_conf.{h,c} and update all callers to
match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in storage_conf.{h,c} and storage_encryption_conf.{h,c}
and update all callers to match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in node_device_conf.{h,c} and update all callers to
match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in network_conf.{h,c} and update all callers to
match
The QEMU flags are commonly stored as a signed or unsigned int,
allowing only 31 flags. This limit is rather close, so to aid
future patches, change it to a 64-bit int
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c,
tests/qemuargv2xmltest.c, tests/qemuhelptest.c, tests/qemuxml2argvtest.c:
Use 'unsigned long long' for QEMU flags
To allow devices to be hot(un-)plugged it is neccessary to ensure
they all have a unique device aliases. This fixes the hotplug
methods to assign device aliases before invoking the monitor
commands which need them
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Expose methods
for assigning device aliases for disks, host devices and
controllers
* src/qemu/qemu_driver.c: Assign device aliases when hotplugging
all types of device
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address-device.args:
Update for changed hostdev naming scheme
The current way of assigning names to the host network backend and
NIC device in QEMU was over complicated, by varying naming scheme
based on the NIC model and backend type. This simplifies the naming
to simply be 'net0' and 'hostnet0', allowing code to easily determine
the host network name and vlan based off the primary device alias
name 'net0'. This in turn allows removal of alot of QEMU specific
code from the XML parser, and makes it easier to assign new unique
names for NICs that are hotplugged
* src/conf/domain_conf.c, src/conf/domain_conf.h: Remove hostnet_name
and vlan fields from virNetworkDefPtr
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c:
Use a single network alias naming scheme regardless of NIC type
or backend type. Determine VLANs from the alias name.
* tests/qemuxml2argvdata/qemuxml2argv-net-eth-names.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args: Update
for new simpler naming scheme
The QEMU 0.12.x tree has the -netdev command line argument, but not
corresponding monitor command. We can't enable the former, without
the latter since it will break hotplug/unplug.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Disable -netdev usage
until 0.13 at earliest
* tests/qemuxml2argvtest.c: Add test for -netdev syntax
* tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.xml: Test
data files for -netdev syntax
The current QEMU code allocates PCI addresses incrementally starting
at 4. This is not satisfactory because the user may have given some
addresses in their XML config, which need to be skipped over when
allocating addresses to remaining devices.
It is thus neccessary to maintain a list of already allocated PCI
addresses and then only allocate ones that remain unused. This is
also required for domain device hotplug to work properly later.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Add APIs for creating
list of existing PCI addresses, and allocating new addresses.
Refactor address assignment to use this code
* src/qemu/qemu_driver.c: Pull PCI address assignment up into the
qemuStartVMDaemon() method, as a prelude to moving it into the
'define' method. Update list of allocated addresses when connecting
to a running VM at daemon startup.
* tests/qemuxml2argvtest.c, tests/qemuargv2xmltest.c,
tests/qemuxml2xmltest.c: Remove USB product test since all
passthrough is done based on address
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.xml: Kil
unused data files
