The iohelper currently calls saferead() to get data from the
underlying file. This has a problem with O_DIRECT when hitting
end-of-file. saferead() is asked to read 1MB, but the first
read() it does may return only a few KB, so it'll try another
read() to fill the remaining buffer. Unfortunately the buffer
pointer passed into this 2nd read() is likely not aligned
to the extent that O_DIRECT requires, so rather than seeing
'0' for end-of-file, we'll get -1 + EINVAL due to misaligned
buffer.
The way the iohelper is currently written, it already handles
getting short reads, so there is actually no need to use
saferead() at all. We can simply call read() directly. The
benefit of this is that we can now write() the data immediately
so when we go into the subsequent reads() we'll always have a
correctly aligned buffer.
Technically the file position ought to be aligned for O_DIRECT
too, but this does not appear to matter when at end-of-file.
Tested-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Add the backing parse and a test case to verify parsing of VxHS
backing storage.
Signed-off-by: Ashish Mittal <Ashish.Mittal@veritas.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
Add a new virStorageNetProtocol for Veritas HyperScale (VxHS) disks
Signed-off-by: Ashish Mittal <Ashish.Mittal@veritas.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
The mlx4 (Mellanox) netdev driver implements the sysfs phys_port_id
file for both VFs and PFs, so you can find the VF netdev plugged into
the same physical port as any given PF netdev by comparing the
contents of phys_port_id of the respective netdevs. That's what
libvirt does when attempting to find the PF netdev for a given VF
netdev (or vice versa).
Most other netdev's drivers don't implement phys_port_id, so the file
is visible in sysfs directory listing, but attempts to read it result
in ENOTSUPP. In these cases, libvirt is unable to read phys_port_id of
either the PF or the VF, so it just returns the first entry in the
PF/VF's list of netdevs.
But we've found that the i40e driver is in between those two
situations - it implements phys_port_id for PF netdevs, but doesn't
implement it for VF netdevs. So libvirt would successfully read the
phys_port_id of the PF netdev, then try to find a VF netdev with
matching phys_port_id, but would fail because phys_port_id is NULL for
all VFs. This would result in a message like the following:
Could not find network device with phys_port_id '3cfdfe9edc39'
under PCI device at /sys/class/net/ens4f1/device/virtfn0
To solve this problem in a way that won't break functionality for
anyone else, this patch saves the first netdev name we find for the
device, and returns that if we fail to find a netdev with the desired
phys_port_id.
Instead of checking for all possible constants that every
kernel header with devlink support should have (and defining
HAVE_DECL_DEVLINK as 1 if any of them is present due to the
way AC_CHECK_DECLS works), only check for DEVLINK_CMD_ESWITCH_GET.
This is the name of the constant since kernel 4.11. Between 4.8
and 4.11, the now deprecated spelling DEVLINK_CMD_ESWITCH_MODE_GET
was used.
Assume DEVLINK_ESWITCH_MODE_SWITCHDEV is available, since it was
introduced along with the deprecated spelling.
Adding functionality to libvirt that will allow querying the interface
for the availability of switchdev Offloading NIC capabilities.
The switchdev mode was introduced in kernel 4.8, the iproute2-devlink
command to retrieve the switchdev NIC feature with command example:
devlink dev eswitch show pci/0000:03:00.0
This feature is needed for Openstack so we can do a scheduling decision
if the NIC is in Hardware Offload (switchdev) or regular SR-IOV (legacy) mode.
And select the appropriate hypervisors with the requested capability see [1].
[1] - https://specs.openstack.org/openstack/nova-specs/specs/pike/approved/enable-sriov-nic-features.html
Reviewed-by: Laine Stump <laine@laine.org>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Some cleanup paths overwrite a usefull error message with a less useful
one and we then try to preserve the original message. The handlers added
in this patch will simplify the operations since they are designed right
for the purpose.
TPM 2 does not implement sysfs files for cancellation of commands.
We therefore use /dev/null for the cancel path passed to QEMU.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Although not previously explicitly documented, the expectation for
the libvirt event loop is that an implementation is registered early
in application startup, before calling any libvirt APIs and then
run forever after. Replacing a previously registered event loop is
not safe & subject to races even if virConnectClose has been called
on open handles, due to delayed deregistration of callbacks during
conenction close.
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
We can now check for the error and not care about the return value as
it will be properly handled in virBufferContentAndReset() anyway.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The function is useful even without using the return value. And if
needed, the return value can be obtained by other calls as well. The
potential for clean-up can be seen in the following patch.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Commit 94c465d0 refactored the logging setup phase but introduced an
issue, where the daemon ignores verbose mode when there are no outputs
defined and the default must be used. The problem is that the default
output was determined too early, thus ignoring the potential '--verbose'
option taking effect. This patch postpones the creation of the default
output to the very last moment when nothing else can change. Since the
default output is only created during the init phase, it's safe to leave
the pointer as NULL for a while, but it will be set eventually, thus not
affecting runtime.
Patch also adjusts both the other daemons.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1442947
Signed-off-by: Erik Skultety <eskultet@redhat.com>
This helper allows you to better structurize the code if some element
may or may not contains attributes and/or child elements.
Reviewed-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The helper returns true if a string contains any of the given chars.
virStringHasControlChars can be reimplemented using that helper.
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
It's equivalent of calling virXPathString("string(.)", ctxt) but it
doesn't have to use the XPath resolving and parsing.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The virXMLPropStringLimit is an equivalent of virXPathStringLimit
which should be preferred if you already have a XML dom node or
if you need to parse more than one property.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Move networkMacMgrFileName into src/util/virmacmap.c and rename to
virMacMapFileName. We're about to move some more MacMgr processing
files into virnetworkobj and it doesn't make sense to have this helper
in the driver or in virnetworkobj.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Rather than assuming that what's passed to virObject{Ref|Unref}
would be a virObjectPtr as long as it's not NULL, let's do the
similar checks virObjectIsClass in order to prevent a possible
increment or decrement to some field at the obj->u.s.refs offset.
Signed-off-by: John Ferlan <jferlan@redhat.com>
The virObjectIsClass API has only ever checked object validity
based on if the @obj is not NULL and it was derived from some class.
While this has worked well in general, there is one additional
check that could be made prior to calling virClassIsDerivedFrom
which loops through the classes checking the magic number against
the klass expected magic number.
If by chance a non virObject is passed, rather than assuming the
void * @obj is a _virObject and thus offsetting to obj->klass,
obj->magic, and obj->parent, let's check that the void * @obj
has at least the "base part" of the magic number in the right
place and generate a more specific VIR_WARN message if not.
There are many consumers to virObjectIsClass, include the locking
primitives virObject{Lock|Unlock}, virObjectRWLock{Read|Write},
and virObjectRWUnlock. For those callers, the locking call will
not fail, but it also will not attempt a virMutex* call which
will "most likely" fail since the &obj->lock is used.
In order to avoid some possible future wrap on the 0xCAFExxxx
value, add a check during initialization that some new class
won't cause the wrap. Should be good for a few years at least!
It is still left up to the caller to handle the failed API calls
just as it would be if it passed a NULL opaque pointer anyobj.
If virObjectIsClass fails "internally" to virobject.c, create a
macro to generate the VIR_WARN describing what the problem is.
Also improve the checks and message a bit to indicate which was
the failure - whether the obj was NULL or just not the right class
Signed-off-by: John Ferlan <jferlan@redhat.com>
Rather than overload virObjectUnlock as commit id '77f4593b' has
done, create a separate virObjectRWUnlock API that will force the
consumers to make the proper decision regarding unlocking the
RWLock's. Similar to the RWLockRead and RWLockWrite, use the
virObjectGetRWLockableObj helper. This restores the virObjectUnlock
code to using the virObjectGetLockableObj.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Introduce a helper to handle the error path more cleanly. The same
as virObjectGetLockableObj in order to essentially follow the original
logic of commit 'b545f65d' to ensure that the input argument at least
has some validity before using.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Now that virObjectRWLockWrite exists to handle the virObjectRWLockable
objects, let's restore virObjectLock to only handle virObjectLockable
class locks. There still exists the possibility that the input @anyobj
isn't a valid object and the resource isn't truly locked, but that
also exists before commit id '77f4593b'.
This also restores some logic that commit id '77f4593b' removed
with respect to a common code path that commit id '10c2bb2b' had
introduced as virObjectGetLockableObj. This code path merely does
the same checks as the original virObjectLock commit 'b545f65d',
but in callable/reusable helper to ensure the @obj at least has
some validity before using.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Instead of making virObjectLock be the entry point for two
different types of locks, let's create a virObjectRWLockWrite API
which will only handle the virObjectRWLockableClass objects.
Use the new virObjectRWLockWrite for the virdomainobjlist code
in order to handle the Add, Remove, Rename, and Load operations
that need to be very synchronous.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Since the class it represents is based on virObjectRWLockableClass
and in order to make sure we differentiate just in case anyone somehow
believes they could use virObjectLockRead for a virObjectLockableClass,
let's rename the API to use the RW in the name. Besides the RW locks
refer to pthread_rwlock_{init|rdlock|wrlock|unlock|destroy} while the
other locks refer to pthread_mutex_{init|lock|unlock|destroy}.
Signed-off-by: John Ferlan <jferlan@redhat.com>
This way later patches can add another structures with virResctrl
prefix without the meaning being even more confusing than it needs to
be.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
That means that returning negative values means error and non-negative
values differ in meaning, but are all successful.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
It doesn't access anything from conf/ and ti will be needed to use
from other util/ places. This split makes the separation clearer.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Commit 81fb440b further qualified an if statement by adding the
boolean saveVlan to the condition. Coverity pointed out that this
change in the logic eliminated the need to check saveVlan in an
argument to virAsprintf().
Commit 9a94af6d restructured virHostdevReadNetConfig() so that it
would manually set ret = 0 after successfully reading the device's
config, but Coverity pointed out that "ret = 0" was erroneously placed
outside of an "else" clause, meaning that the the value of ret set in
the "if" clause was unnecessarily and incorrectly overwritten.
This patch moves ret = 0 into the else clause, which should silence
Coverity.
When using a VF from an SRIOV-capable network card in a guest (either
in macvtap passthrough mode, or via VFIO PCI device assignment), The
associated PF netdev must be online in order for the VF to be usable
by the guest. The guest, however, is not able to change the state of
the PF. And libvirt *could* set the PF online as needed, but that
could lead to the host receiving unexpected IPv6 traffic (since the
default for an unconfigured interface is to participate in IPv6
autoconf). For this reason, before assigning a VF to a guest, libvirt
verifies that the related PF netdev is online - if it isn't, then we
log an error and don't allow the guest startup to continue.
Until now, this check was done during virNetDevSetNetConfig(). This
works nicely because the same function is called both for macvtap
passthrough and for VFIO device assignment. But in the case of VFIO,
the VF has already been unbound from its netdev driver by the time we
get to virNetDevSetNetConfig(), and in the case of dual port Mellanox
NICs that have their VFs setup in single port mode, the *only* way to
determine the proper PF netdev to query for online status is via the
"phys_port_id" file that is in the VF netdev's sysfs directory. *BUT*
if we've unbound the VF from the netdev driver, then it doesn't *have*
a netdev sysfs directory.
So, in order to check the correct PF netdev for online status, this
patch moved the check earlier in the setup, into
virNetDevSaveNetConfig(), which is called *before* unbinding the VF
from its netdev driver.
(Note that this implies that if you are using VFIO device assignment
for the VFs of a Mellanox NIC that has the VFs programmed in single
port mode, you must let the VFs be bound to their net driver and use
"managed='yes'" in the device definition. To be more specific, this is
only true if the VFs in single port mode are using port *2* of the PF
- if the VFs are using only port 1, then the correct PF netdev will be
arrived at by default/chance))
This resolves: https://bugzilla.redhat.com/267191
virHostdevRestoreNetConfig() calls virNetDevReadNetConfig() to try and
read the "original config" of a netdev, and if that fails, it tries
again with a different directory/netdev name. This achieves the
desired effect (we end up finding the config wherever it may be), but
for each failure, virNetDevReadNetConfig() places a nice error message
in the system logs. Experience has shown that false-positive error
logs like this lead to erroneous bug reports, and can often mislead
those searching for *real* bugs.
This patch changes virNetDevReadNetConfig() to explicitly check if the
file exists before calling virFileReadAll(); if it doesn't exist,
virNetDevReadNetConfig() returns a success, but leaves all the
variables holding the results as NULL. (This makes sense if you define
the purpose of the function as "read a netdev's config from its config
file *if that file exists*).
To take advantage of that change, the caller,
virHostdevRestoreNetConfig() is modified to fail immediately if
virNetDevReadNetConfig() returns an error, and otherwise to try the
different directory/netdev name if adminMAC & vlan & MAC are all NULL
after the preceding attempt.
Mellanox ConnectX-3 dual port SRIOV NICs present a bit of a challenge
when assigning one of their VFs to a guest using VFIO device
assignment.
These NICs have only a single PCI PF device, and that single PF has
two netdevs sharing the single PCI address - one for port 1 and one
for port 2. When a VF is created it can also have 2 netdevs, or it can
be setup in "single port" mode, where the VF has only a single netdev,
and that netdev is connected either to port 1 or to port 2.
When the VF is created in dual port mode, you get/set the MAC
address/vlan tag for the port 1 VF by sending a netlink message to the
PF's port1 netdev, and you get/set the MAC address/vlan tag for the
port 2 VF by sending a netlink message to the PF's port 2 netdev. (Of
course libvirt doesn't have any way to describe MAC/vlan info for 2
ports in a single hostdev interface, so that's a bit of a moot point)
When the VF is created in single port mode, you can *set* the MAC/vlan
info by sending a netlink message to *either* PF netdev - the driver
is smart enough to understand that there's only a single netdev, and
set the MAC/vlan for that netdev. When you want to *get* it, however,
the driver is more accurate - it will return 00:00:00:00:00:00 for the
MAC if you request it from the port 1 PF netdev when the VF was
configured to be single port on port 2, or if you request if from the
port 2 PF netdev when the VF was configured to be single port on port
1.
Based on this information, when *getting* the MAC/vlan info (to save
the original setting prior to assignment), we determine the correct PF
netdev by matching phys_port_id between VF and PF.
(IMPORTANT NOTE: this implies that to do PCI device assignment of the
VFs on dual port Mellanox cards using <interface type='hostdev'>
(i.e. if you want the MAC address/vlan tag to be set), not only must
the VFs be configured in single port mode, but also the VFs *must* be
bound to the host VF net driver, and libvirt must use managed='yes')
By the time libvirt is ready to set the new MAC/vlan tag, the VF has
already been unbound from the host net driver and bound to
vfio-pci. This isn't problematic though because, as stated earlier,
when a VF is created in single port mode, commands to configure it can
be sent to either the port 1 PF netdev or the port 2 PF netdev.
When it is time to restore the original MAC/vlan tag, again the VF
will *not* be bound to a host net driver, so it won't be possible to
learn from sysfs whether to use the port 1 or port 2 PF netdev for the
netlink commands. And again, it doesn't matter which netdev you
use. However, we must keep in mind that we saved the original settings
to a file called "${PF}_${VFNUM}". To solve this problem, we just
check for the existence of ${PF1}_${VFNUM} and ${PF2}_${VFNUM}, and
use whichever one we find (since we know that only one can be there)
This patch updates functions in netdev.c to pay attention to
phys_port_id. It uses the new function virNetDevGetPhysPortID() to
learn the phys_port_id of a VF or PF, then sends that info to
virPCIGetNetName(), which has newly been modified to take an optional
phys_port_id.
A single PCI device may have multiple netdevs associated with it. Each
of those netdevs will have a different phys_port_id entry in
sysfs. This patch modifies virPCIGetNetName() to allow selecting one
of the potential many netdevs in two different ways:
1) by setting the "idx" argument, the caller can select the 1st (0),
2nd (1), etc. netdev from the PCI device's net subdirectory.
2) If the physPortID arg is set (to a null-terminated string) then
virPCIGetNetName() returns the netdev that has that phys_port_id in
the sysfs file of the same name in the netdev's directory.
On Linux each network device *can* (but not necessarily *does*) have
an attribute called phys_port_id which can be read from the file of
that name in the netdev's sysfs directory. The examples I've seen have
been a many-digit hexadecimal number (as an ASCII string).
This value can be useful when a single PCI device is associated with
multiple netdevs (e.g a dual port Mellanox SR-IOV NIC - this card has
a single PCI Physical Function (PF), and that PF has two netdevs
associated with it (the "net" subdirectory of the PF in sysfs has two
links rather than the usual single link to a netdev directory). Each
of the PF netdevs has a different phys_port_id. The Virtual Functions
(VF) are similar - the PF (a PCI device) has "n" VFs (also each of
these is a PCI device), each VF has two netdevs, and each of the VF
netdevs points back to the VF PCI device (with the "device" entry in
its sysfs directory) as well as having a phys_port_id matching the PF
netdev it is associated with.
virNetDevGetPhysPortID() simply attempts to read the phys_port_id for
the given netdev and return it to the caller. If this particular
netdev driver doesn't support phys_port_id, it returns NULL (*not* a
NULL-terminated string, but a NULL pointer) but still counts it as a
success.
We are given a string in @machinename, we never allocate it, just
merely use it for reading. We should not free it otherwise it
leads to double free:
==32191== Thread 17:
==32191== Invalid free() / delete / delete[] / realloc()
==32191== at 0x4C2D1A0: free (vg_replace_malloc.c:530)
==32191== by 0x54BBB84: virFree (viralloc.c:582)
==32191== by 0x2BC04499: qemuProcessStop (qemu_process.c:6313)
==32191== by 0x2BC500FF: processMonitorEOFEvent (qemu_driver.c:4724)
==32191== by 0x2BC502FC: qemuProcessEventHandler (qemu_driver.c:4769)
==32191== by 0x5550640: virThreadPoolWorker (virthreadpool.c:167)
==32191== by 0x554FBCF: virThreadHelper (virthread.c:206)
==32191== by 0x8F913D3: start_thread (in /lib64/libpthread-2.23.so)
==32191== by 0x928DE3C: clone (in /lib64/libc-2.23.so)
==32191== Address 0x31893d70 is 0 bytes inside a block of size 1,100 free'd
==32191== at 0x4C2D1A0: free (vg_replace_malloc.c:530)
==32191== by 0x54BBB84: virFree (viralloc.c:582)
==32191== by 0x54C1936: virCgroupValidateMachineGroup (vircgroup.c:343)
==32191== by 0x54C4B29: virCgroupNewDetectMachine (vircgroup.c:1550)
==32191== by 0x2BBDDA29: qemuConnectCgroup (qemu_cgroup.c:972)
==32191== by 0x2BC05DA7: qemuProcessReconnect (qemu_process.c:6822)
==32191== by 0x554FBCF: virThreadHelper (virthread.c:206)
==32191== by 0x8F913D3: start_thread (in /lib64/libpthread-2.23.so)
==32191== by 0x928DE3C: clone (in /lib64/libc-2.23.so)
==32191== Block was alloc'd at
==32191== at 0x4C2BE80: malloc (vg_replace_malloc.c:298)
==32191== by 0x4C2E35F: realloc (vg_replace_malloc.c:785)
==32191== by 0x54BB492: virReallocN (viralloc.c:245)
==32191== by 0x54BEDF2: virBufferGrow (virbuffer.c:150)
==32191== by 0x54BF3B9: virBufferVasprintf (virbuffer.c:408)
==32191== by 0x54BF324: virBufferAsprintf (virbuffer.c:381)
==32191== by 0x55BB271: virDomainGenerateMachineName (domain_conf.c:27078)
==32191== by 0x2BBD5B8F: qemuDomainGetMachineName (qemu_domain.c:9595)
==32191== by 0x2BBDD9B4: qemuConnectCgroup (qemu_cgroup.c:966)
==32191== by 0x2BC05DA7: qemuProcessReconnect (qemu_process.c:6822)
==32191== by 0x554FBCF: virThreadHelper (virthread.c:206)
==32191== by 0x8F913D3: start_thread (in /lib64/libpthread-2.23.so)
Moreover, make the @machinename 'const char *' to mark it
explicitly that we are not changing the passed string.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
