The QEMU 0.13 release is finally out and from testing in RHEL-6
we know that its JSON and netdev features are now good enough
for us to use by default.
* src/qemu/qemu_conf.c: Enable JSON + netdev for QEMU >= 0.13
This sets the process name to the same value as the Windows title,
but since the name is limited to 16 chars only this is kept as a
configuration option and turned off by default
* src/qemu/qemu.conf src/qemu/qemu_conf.[ch]: hceck for support in the
QEmu help output, add the option in qemu conf file and augment
qemudBuildCommandLine to add it if switched on
* src/qemu/libvirtd_qemu.aug src/qemu/test_libvirtd_qemu.aug: augment
the augeas lenses accordingly
* tests/qemuhelptest.c: cope with the extra flag being detected now
* src/qemu/qemu_conf.c (qemuParseCommandLineSmp): Distinguish
between vcpus and maxvcpus, for new enough qemu.
* tests/qemuargv2xmltest.c (mymain): Add new test.
* tests/qemuxml2argvtest.c (mymain): Likewise.
* tests/qemuxml2xmltest.c (mymain): Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-smp.args: New file.
Although this patch adds a distinction between maximum vcpus and
current vcpus in the XML, the values should be identical for all
drivers at this point. Only in subsequent per-driver patches will
a distinction be made.
In general, virDomainGetInfo should prefer the current vcpus.
* src/conf/domain_conf.h (_virDomainDef): Adjust vcpus to unsigned
short, to match virDomainGetInfo limit. Add maxvcpus member.
* src/conf/domain_conf.c (virDomainDefParseXML)
(virDomainDefFormat): parse and print out vcpu details.
* src/xen/xend_internal.c (xenDaemonParseSxpr)
(xenDaemonFormatSxpr): Manage both vcpu numbers, and require them
to be equal for now.
* src/xen/xm_internal.c (xenXMDomainConfigParse)
(xenXMDomainConfigFormat): Likewise.
* src/phyp/phyp_driver.c (phypDomainDumpXML): Likewise.
* src/openvz/openvz_conf.c (openvzLoadDomains): Likewise.
* src/openvz/openvz_driver.c (openvzDomainDefineXML)
(openvzDomainCreateXML, openvzDomainSetVcpusInternal): Likewise.
* src/vbox/vbox_tmpl.c (vboxDomainDumpXML, vboxDomainDefineXML):
Likewise.
* src/xenapi/xenapi_driver.c (xenapiDomainDumpXML): Likewise.
* src/xenapi/xenapi_utils.c (createVMRecordFromXml): Likewise.
* src/esx/esx_vmx.c (esxVMX_ParseConfig, esxVMX_FormatConfig):
Likewise.
* src/qemu/qemu_conf.c (qemuBuildSmpArgStr)
(qemuParseCommandLineSmp, qemuParseCommandLine): Likewise.
* src/qemu/qemu_driver.c (qemudDomainHotplugVcpus): Likewise.
* src/opennebula/one_conf.c (xmlOneTemplate): Likewise.
This introduces new attribute to filesystem element
to support customizable access mode for mount type.
Valid accessmode are: passthrough, mapped and squash.
Usage:
<filesystem type='mount' accessmode='passthrough'>
<source dir='/export/to/guest'/>
<target dir='mount_tag'/>
</filesystem>
passthrough is the default model if not specified, that's
also the current behaviour.
This enables support for nested SVM using the regular CPU
model/features block. If the CPU model or features include
'svm', then the '-enable-nesting' flag will be added to the
QEMU command line. Latest out of tree patches for nested
'vmx', no longer require the '-enable-nesting' flag. They
instead just look at the cpu features. Several of the models
already include svm support, but QEMU was just masking out
the svm bit silently. So this will enable SVM on such
models
* src/qemu/qemu_conf.h: flag for -enable-nesting
* src/qemu/qemu_conf.c: Use -enable-nesting if VMX or SVM are in
the CPUID
* src/cpu/cpu.h, src/cpu/cpu.c: API to check for a named feature
* src/cpu/cpu_x86.c: x86 impl of feature check
* src/libvirt_private.syms: Add cpuHasFeature
* src/qemuhelptest.c: Add nesting flag where required
Make use of the existing <filesystem> element to support plan9fs
filesystem passthrough in the QEMU driver
<filesystem type='mount'>
<source dir='/export/to/guest'/>
<target dir='/import/from/host'/>
</filesystem>
NB, the target is not actually a directory, it is merely a arbitrary
string tag that is exported to the guest as a hint for where to mount
it.
Adding parsing code for memory tunables in the domain xml file
also change the internal define structures used for domain memory
informations
Adds a new specific test
A QEMU guest can have upto VIR_DOMAIN_BOOT_LAST boot entries
defined. When building the QEMU arg, each entry takes a
single byte. This means the array must be declared to be
VIR_DOMAIN_BOOT_LAST+1 bytes in length to allow for the
trailing null
* src/qemu/qemu_conf.c: Fix off-by-1 boot arg array size
Previously QEMU enabled KQEMU by default and had -no-kqemu.
0.11.x switched to requiring -enable-kqemu. 0.12.x dropped
kqemu entirely. This patch adds support for -enable-kqemu
so 0.11.x works. It replaces a huge set of if() with a
switch() to make the code a bit more readable.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Support
-enable-kqemu
We already filled the PCI address structure when we checked whether it's
free or not, so let's just use the structure here instead of filling it
again.
The balloon device is automatically added to qemu guests if supported,
but it may be useful to desactivate it. The simplest to not change the
existing behaviour is to allow
<memballoon type="none"/>
as an extra option to desactivate it (it is automatically added if the
memballoon construct is missing for the domain).
The following simple patch just adds the extra option and does not
change the default behaviour but avoid creating a balloon device if
type="none" is used.
* docs/schemas/domain.rng: add the extra type attribute value
* src/conf/domain_conf.c src/conf/domain_conf.h: add the extra enum
value
* src/qemu/qemu_conf.c: if enum is NONE, don't activate the device,
i.e. don't pass the args to qemu/kvm
Fix the error checking to use the return value from brAddTap() instead
of checking the current errno value which might have been changed by
clean up calls inside of brAddTap().
Signed-off-by: Doug Goldstein <cardoe@gentoo.org>
Added a more detailed error message when adding a tap devices fails and
the kernel is missing tun support.
Signed-off-by: Doug Goldstein <cardoe@gentoo.org>
the followup on the boot=on problem, basically it's not needed to
specify it when booting out of IDE devices when using KVM
* src/qemu/qemu_conf.c: do not use boot=on for IDE devices
* tests/qemuxml2argvdata/qemuxml2argv*.args: this changes the output
for 5 of the tests
Patch version revamped by Eric Blake <eblake@redhat.com> of Jiri
Denemark <jdenemar@redhat.com> original patch
When attaching a PCI device which doesn't explicitly set its PCI
address, libvirt allocates the address automatically. The problem is
that when checking which PCI address is unused, we only check for those
with slot number higher than the highest slot number ever used.
Thus attaching/detaching such device several times in a row (31 is the
theoretical limit, less then 30 tries are enough in practise) makes any
further device attachment fail. Furthermore, attaching a device with
predefined PCI address to 0:0:31 immediately forbids attachment of any
PCI device without explicit address.
This patch changes the logic so that we always check all PCI addresses
before we say there is no PCI address available.
Modifications from v1: revert back to remembering the last slot
reserved, but allow wraparound to not be limited by the end.
In this way, slots are still assigned in the same order as
before the patch, rather than filling in the gaps closest to
0 and risking making windows guests mad.
* src/qemu/qemu_conf.c: fix pci reservation code to do a round-robbin
check of all available PCI splot availability before failing.
Basically the 'boot=on' boot selection device is something present in
KVM but not in upstream QEmu, as a result if we boot a QEmu domain
without KVM acceleration we must disable boot=on ... even if the front
end kvm binary expose that capability in the help page.
* src/qemu/qemu_conf.c: in qemudBuildCommandLine if -no-kvm
is passed, then deactivate QEMUD_CMD_FLAG_DRIVE_BOOT
ADD_ARG_LIT should only be used for literal arguments,
since it duplicates the memory. Since virBufferContentAndReset
is already allocating memory, we should only use ADD_ARG.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
All <console> devices now export a <target> type attribute. QEMU defaults
to 'serial', UML defaults to 'uml, xen can be either 'serial' or 'xen'
depending on fullvirt. Understandably there is lots of test fallout.
This will be used to differentiate between a serial vs. virtio console for
QEMU.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
targetType only tracks the actual <target> format we are parsing. Currently
we only fill abide this value for channel devices.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
There is actually a difference between the character device type (serial,
parallel, channel, ...) and the target type (virtio, guestfwd). Currently
they are awkwardly conflated.
Start to pull them apart by renaming targetType -> deviceType. This is
an entirely mechanical change.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
QEMU has had two different syntax for disk cache options
Old: on|off
New: writeback|writethrough|none
QEMU recently added another 'unsafe' option which broke the
libvirt check. We can avoid this & future breakage, if we
do a negative check for the old syntax, instead of a positive
check for the new syntax
* src/qemu/qemu_conf.c: Invert cache option check
Add a new element to the <os> block:
<bootmenu enable="yes|no"/>
Which maps to -boot,menu=on|off on the QEMU command line.
I decided to use an explicit 'enable' attribute rather than just make the
bootmenu element boolean. This allows us to treat lack of a bootmenu element
as 'use hypervisor default'.
Now that we have the ability to specify arbitrary qemu
command-line parameters in the XML, use it to handle unknown
command-line parameters when doing a native-to-xml conversion.
Changes since v1:
- Rename num_extra to num_args
- Fix up a memory leak on an error path
Changes since v2:
- Add a VIR_WARN when adding the argument via qemu:arg
Changes since v3:
- None
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Implement the qemu hooks for XML namespace data. This
allows us to specify a qemu XML namespace, and then
specify:
<qemu:commandline>
<qemu:arg value='arg'/>
<qemu:env name='name' value='value'/>
</qemu:commandline>
In the domain XML.
Changes since v1:
- Change the <qemu:arg>arg</qemu:arg> XML to <qemu:arg value='arg'/> XML
- Fix up some memory leaks in qemuDomainDefNamespaceParse
- Rename num_extra and extra to num_args and args, respectively
- Fixed up some error messages
- Make sure to escape user-provided data in qemuDomainDefNamespaceFormatXML
Changes since v2:
- Add checking to ensure environment variable names are valid
- Invert the logic in qemuDomainDefNamespaceFormatXML to return early
Changes since v3:
- Change strspn() to c_isalpha() check of first letter of environment variable
Signed-off-by: Chris Lalancette <clalance@redhat.com>
A Linux software bridge will assume the MAC address of the enslaved
interface with the numerically lowest MAC addr. When the bridge
changes MAC address there is a period of network blackout, so a
change should be avoided. The kernel gives TAP devices a completely
random MAC address. Occassionally the random TAP device MAC is lower
than that of the physical interface (eth0, eth1etc) that is enslaved,
causing the bridge to change its MAC.
This change sets an explicit MAC address for all TAP devices created
using the configured MAC from the XML, but with the high byte set
to 0xFE. This should ensure TAP device MACs are higher than any
physical interface MAC.
* src/qemu/qemu_conf.c, src/uml/uml_conf.c: Pass in a MAC addr
for the TAP device with high byte set to 0xFE
* src/util/bridge.c, src/util/bridge.h: Set a MAC when creating
the TAP device to override random MAC
The PCI slot 1 must be reserved at all times, since PIIX3 is
always present, even if no IDE device is in use for guest disks
* src/qemu/qemu_conf.c: Always reserve slot 1 for PIIX3
To try and ensure that people upgrading from old QEMU get guests
with the same PCI device ordering, change the way we assign addrs
to match QEMU's default order. This should make Windows less
annoyed.
* src/qemu/qemu_conf.c: Follow QEMU's default PCI ordering
logic when assigning addresses
* tests/*.args: Update for changed PCI addresses
To allow compatibility with older QEMU PCI device slot assignment
it is necessary to explicitly track the balloon device in the
XML. This introduces a new device
<memballoon model='virtio|xen'/>
It can also have a PCI address, auto-assigned if necessary.
The memballoon will be automatically added to all Xen and QEMU
guests by default.
* docs/schemas/domain.rng: Add <memballoon> element
* src/conf/domain_conf.c, src/conf/domain_conf.h: parsing
and formatting for memballoon device. Always add a memory
balloon device to Xen/QEMU if none exists in XML
* src/libvirt_private.syms: Export memballoon model APIs
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Honour the
PCI device address in memory balloon device
* tests/*: Update to test new functionality
The first VGA and IDE devices need to have fixed PCI address
reservations. Currently this is handled inline with the other
non-primary VGA/IDE devices. The fixed virtio balloon device
at slot 3, ensures auto-assignment skips the slots 1/2. The
virtio address will shortly become configurable though. This
means the reservation of fixed slots needs to be done upfront
to ensure that they don't get re-used for other devices.
This is more or less reverting the previous changeset:
commit 83acdeaf17
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Wed Feb 3 16:11:29 2010 +0000
Fix restore of QEMU guests with PCI device reservation
The difference is that this time, instead of unconditionally
reserving the address, we only reserve the address if it was
initially type=none. Addresses of type=pci were handled
earlier in process by qemuDomainPCIAddressSetCreate(). This
ensures restore step doesn't have problems
* src/qemu/qemu_conf.c: Reserve first VGA + IDE address
upfront
The VIR_ERR_NO_SUPPORT refers to an API which is not implemented.
There is a separate VIR_ERR_CONFIG_UNSUPPORTED for XML config
options that are not available with the current hypervisor.
* src/qemu/qemu_conf.c, src/qemu/qemu_driver.c: Remove
many VIR_ERR_NO_SUPPORT replace with VIR_ERR_CONFIG_UNSUPPORTED
Disk format probing is now disabled by default. A new config
option in /etc/qemu/qemu.conf will re-enable it for existing
deployments where this causes trouble
In case qemu supports -nodefconfig, libvirt adds uses it when launching
new guests. Since this option may affect CPU models supported by qemu,
we need to use it when probing for available models.
We previously assumed that if the -device option existed in qemu, that
-nodefconfig would also exist. It turns out that isn't the case, as
demonstrated by qemu-kvm-0.12.3 in Fedora 13.
*/src/qemu/qemu_conf.[hc] - add a new QEMUD_CMD_FLAG, set it via the
help output, and check it before adding
-nodefconfig to the qemu commandline.
The domain XML parsing code autogenerates disk address and
controller elements when they are not explicitly specified.
The code assumes a narrow SCSI bus (7 units per bus). ESX
uses a wide SCSI bus (16 units per bus).
This is a step towards controller support for the ESX driver.
We already use the '-nodefaults' command line arg with QEMU to stop
it adding any default devices to guests. Unfortunately, QEMU will
load global config files from /etc/qemu that may also add default
devices. These aren't blocked by '-nodefaults', so we need to also
add the '-nodefconfig' arg to prevent that.
Unfortunately these global config files are also used to define
custom CPU models. So in blocking global hardware device addition
we also block definitions of new CPU models. Libvirt doesn't know
about these custom CPU models though, so it would never make use
of them anyway. Thus blocking them via -nodefconfig isn't a show
stopping problem. We would need to expand libvirt's own CPU model
XML database to support these instead.
* src/qemu/qemu_conf.c: Add '-nodefconfig' if available
* tests/qemuxml2argvdata/: Add '-nodefconfig' to all data files which
have '-nodefaults' present
Following Daniel Berrange's multiple helpful suggestions for improving
this patch and introducing another driver interface, I now wrote the
below patch where the nwfilter driver registers the functions to
instantiate and teardown the nwfilters with a function in
conf/domain_nwfilter.c called virDomainConfNWFilterRegister. Previous
helper functions that were called from qemu_driver.c and qemu_conf.c
were move into conf/domain_nwfilter.h with slight renaming done for
consistency. Those functions now call the function expored by
domain_nwfilter.c, which in turn call the functions of the new driver
interface, if available.
To ensure that the device addressing scheme is stable across
hotplug/unplug, all virtio serial channels needs to have an
associated port number in their address. This is then specified
to QEMU using the nr=NNN parameter
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parsing
for port number in vioserial address types.
* src/qemu/qemu_conf.c: Set 'nr=NNN' parameter with virtio
serial port number
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: Expand
data set to ensure coverage of port addressing
This patch that adds support for configuring 802.1Qbg and 802.1Qbh
switches. The 802.1Qbh part has been successfully tested with real
hardware. The 802.1Qbg part has only been tested with a (dummy)
server that 'behaves' similarly to how we expect lldpad to 'behave'.
The following changes were made during the development of this patch:
- Merging Scott's v13-pre1 patch
- Fixing endptr related bug while using virStrToLong_ui() pointed out
by Jim Meyering
- Addressing Jim Meyering's comments to v11
- requiring mac address to the vpDisassociateProfileId() function to
pass it further to the 802.1Qbg disassociate part (802.1Qbh untouched)
- determining pid of lldpad daemon by reading it from /var/run/libvirt.pid
(hardcode as is hardcode alson in lldpad sources)
- merging netlink send code for kernel target and user space target
(lldpad) using one function nlComm() to send the messages
- adding a select() after the sending and before the reading of the
netlink response in case lldpad doesn't respond and so we don't hang
- when reading the port status, in case of 802.1Qbg, no status may be
received while things are 'in progress' and only at the end a status
will be there.
- when reading the port status, use the given instanceId and vf to pick
the right IFLA_VF_PORT among those nested under IFLA_VF_PORTS.
- never sending nor parsing IFLA_PORT_SELF type of messages in the
802.1Qbg case
- iterating over the elements in a IFLA_VF_PORTS to pick the right
IFLA_VF_PORT by either IFLA_PORT_PROFILE and given profileId
(802.1Qbh) or IFLA_PORT_INSTANCE_UUID and given instanceId (802.1Qbg)
and reading the current status in IFLA_PORT_RESPONSE.
- recycling a previous patch that adds functionality to interface.c to
- get the vlan identifier on an interface
- get the flags of an interface and some convenience function to
check whether an interface is 'up' or not (not currently used here)
- adding function to determine the root physical interface of an
interface. For example if a macvtap is linked to eth0.100, it will
find eth0. Also adding a function that finds the vlan on the 'way to
the root physical interface'
- conveying the root physical interface name and index in case of 802.1Qbg
- conveying mac address of macvlan device and vlan identifier in
IFLA_VFINFO_LIST[ IFLA_VF_INFO[ IFLA_VF_MAC(mac), IFLA_VF_VLAN(vlan) ] ]
to (future) lldpad via netlink
- To enable build with --without-macvtap rename the
[dis|]associatePortProfileId functions, prepend 'vp' before their
name and make them non-static functions.
- Renaming variable multicast to nltarget_kernel and inverting
the logic
- Addressing Jim Meyering's comments; this also touches existing
code for example for correcting indentation of break statements or
simplification of switch statements.
- Renamed occurrencvirVirtualPortProfileDef to virVirtualPortProfileParamses
- 802.1Qbg part prepared for sending a RTM_SETLINK and getting
processing status back plus a subsequent RTM_GETLINK to
get IFLA_PORT_RESPONSE.
Note: This interface for 802.1Qbg may still change
- [David Allan] move getPhysfn inside IFLA_VF_PORT_MAX to avoid
compiler
warning when latest if_link.h isn't available
- move from Stefan's 802.1Qb{g|h} XML v8 to v9
- move hostuuid and vf index calcs to inside doPortProfileOp8021Qbh
- remove debug fprintfs
- use virGetHostUUID (thanks Stefan!)
- fix compile issue when latest if_link.h isn't available
- change poll timeout to 10s, at 1/8 intervals
- if polling times out, log msg and return -ETIMEDOUT
- Add Stefan's code for getPortProfileStatus
- Poll for up to 2 secs for port-profile status, at 1/8 sec intervals:
- if status indicates error, abort openMacvtapTap
- if status indicates success, exit polling
- if status is "in-progress" after 2 secs of polling, exit
polling loop silently, without error
My patch finishes out the 802.1Qbh parts, which Stefan had mostly complete.
I've tested using the recent kernel updates for VF_PORT netlink msgs and
enic for Cisco's 10G Ethernet NIC. I tested many VMs, each with several
direct interfaces, each configured with a port-profile per the XML. VM-to-VM,
and VM-to-external work as expected. VM-to-VM on same host (using same NIC)
works same as VM-to-VM where VMs are on diff hosts. I'm able to change
settings on the port-profile while the VM is running to change the virtual
port behaviour. For example, adjusting a QoS setting like rate limit. All
VMs with interfaces using that port-profile immediatly see the effect of the
change to the port-profile.
I don't have a SR-IOV device to test so source dev is a non-SR-IOV device,
but most of the code paths include support for specifing the source dev and
VF index. We'll need to complete this by discovering the PF given the VF
linkdev. Once we have the PF, we'll also have the VF index. All this info-
mation is available from sysfs.
Since the macvtap device needs active tear-down and the teardown logic
is based on the interface name, it can happen that if for example 1 out
of 3 interfaces was successfully created, that during the failure path
the macvtap's target device name is used to tear down an interface that
is doesn't own (owned by another VM).
So, in this patch, the target interface name is reset so that there is
no target interface name and the interface name is always cleared after
a tear down.
This allows libvirt to open the PCI device sysfs config file prior
to dropping privileges so qemu can access the full config space.
Without this, a de-privileged qemu can only access the first 64
bytes of config space.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Detect support
for pci-assign.configfd option. Use this option when formatting
PCI device string if possible
* src/qemu/qemu_driver.c: Pre-open PCI sysfs config file and pass
to QEMU
This patch parses the following two XML descriptions, one for
802.1Qbg and one for 802.1Qbh, and stores the data internally.
The actual triggering of the switch setup protocol has not been
implemented here but the relevant code to do that should go into
the functions associatePortProfileId() and disassociatePortProfileId().
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbg'>
<parameters managerid='12' typeid='0x123456' typeidversion='1'
instanceid='fa9b7fff-b0a0-4893-8e0e-beef4ff18f8f'/>
</virtualport>
<filterref filter='clean-traffic'/>
</interface>
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbh'>
<parameters profileid='my_profile'/>
</virtualport>
</interface>
I'd suggest to use this patch as a base for triggering the setup
protocol with the 802.1Qb{g|h} switch.
Several rounds of changes were made to this patch. The
following is a list of these changes.
- Renamed structure virVirtualPortProfileDef to virVirtualPortProfileParams
as per Daniel Berrange's request
- Addressing Daniel Berrange's comments:
- removing macvtap.h's dependency on domain_conf.h by
moving the virVirtualPortProfileDef structure into macvtap.h
and not passing virtDomainNetDefPtr to any functions in
macvtap.c
- Addressed most of Chris Wright's comments:
- indicating error in case virtualport XML node cannot be parsed
properly
- parsing hex and decimal numbers using virStrToLong_ui() with
parameter '0' for base
- tgifname (target interface name) variable wasn't necessary
to pass to openMacvtapTap function anymore
- assigning the virtual port data structure to the virDomainNetDef
only if it was previously parsed
- make sure that the error code returned by openMacvtapTap() is a negative n
in case the associatePortProfileId() function failed.
- renaming vsi in the XML to virtualport
- replace all occurrences of vsi in the source as well
- removing mode and MAC address parameters from the functions that
will communicate with the hareware diretctly or indirectly
- moving the associate and disassociate functions to the end of the
file for subsequent patches to easier make them generally available
for export
- passing the macvtap interface name rather than the link device since
this otherwise gives funny side effects when using netlink messages
where IFLA_IFNAME and IFLA_ADDRESS are specified and the link dev
all of a sudden gets the MAC address of the macvtap interface.
- Removing rc = -1 error indications in the case of 802.1Qbg|h setup in case
we wanted to use hook scripts for the setup and so the setup doesn't fail
here.
- if instance ID UUID is not supplied it will automatically be generated
- adapted schema to make instance ID UUID optional
- added test case
- parser and XML generator have been separated into their own
functions so they can be re-used elsewhere (passthrough case
for example)
- Adapted XML parser and generator support the above shown type
(802.1Qbg, 802.1Qbh).
- Adapted schema to above XML
- Adapted test XML to above XML
- Passing through the VM's UUID which seems to be necessary for
802.1Qbh -- sorry no host UUID
- adding virtual function ID to association function, in case it's
necessary to use (for SR-IOV)
Currently all host audio backends are disabled if a VM is using VNC, in
favor of the QEMU VNC audio extension. Unfortunately no released VNC
client supports this extension, so users have no way of getting audio
to work if using VNC.
Add a new config option in qemu.conf which allows changing libvirt's
behavior, but keep the default intact.
v2: Fix doc typos, change name to vnc_allow_host_audio
* src/qemu/qemu_conf.c (qemudParseHelpStr): Fix errors that made
it impossible to diagnose invalid minor and micro version number
components.
Signed-off-by: Chris Wright <chrisw@redhat.com>
* src/qemu/qemu_conf.c (QEMU_VERSION_STR_1, QEMU_VERSION_STR_2):
Define these instead of...
(QEMU_VERSION_STR): ... this. Remove definition.
(qemudParseHelpStr): Check first for the new, shorter prefix,
"QEMU emulator version", and then for the old one,
"QEMU PC emulator version" when trying to parse the version number.
Based on a patch by Chris Wright.
There doesn't seem to be anything specific to tap devices for this
array of file descriptors which need to stay open of the guest to use.
Rename then for others to make use of.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Approximately 60 messages were marked. Since these diagnostics are
intended solely for developers and maintainers, encouraging translation
is deemed to be counterproductive:
http://thread.gmane.org/gmane.comp.emulators.libvirt/25050/focus=25052
Run this command:
git grep -l VIR_WARN|xargs perl -pi -e \
's/(VIR_WARN0?)\s*\(_\((".*?")\)/$1($2/'
qemuDomainPCIAddressSetFree was freeing up the hash
table for the pci addresses, but not freeing up the addr
structure. Looking over the callers of this function, it
seems like they expect it to also free up the structure,
so do that here.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Adds ability to provide a preferred CPU model for CPUID data decoding.
Such model would be considered as the best possible model (if it's
supported by hypervisor) regardless on number of features which have to
be added or removed for describing required CPU.
So far, when CPUID data were converted into CPU model and features, the
features can only be added to the model. As a result, when a guest asked
for something like "qemu64,-svm" it would get a qemu32 plus a bunch of
additional features instead.
This patch adds support for removing feature from the base model.
Selection algorithm remains the same: the best CPU model is the model
which requires lowest number of features to be added/removed from it.
Qemu committed a patch which list some CPU names in [] when asked for
supported CPUs (qemu -cpu ?). Yet, it needs such CPUs to be passed
without those square braces. When probing for supported CPU models, we
can just strip the square braces and pretend we have never seen them.
Disk devices in QEMU have two parts, the guest device and the host
backend driver. Historically these two parts have had the same
"unique" name. With the switch to using -device though, they now
have separate names. Thus when changing CDROM media, for guests
using -device syntax, we need to prepend the QEMU_DRIVE_HOST_PREFIX
constant
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Add helper function
qemuDeviceDriveHostAlias() for building a host backend alias
* src/qemu/qemu_driver.c: Use qemuDeviceDriveHostAlias() to determine
the host backend alias for performing eject/change commands in the
monitor
The device_add command was added in JSON mode in a way I didn't
expect. Instead of passing the normal device string to the JSON
command:
{ "execute": "device_add", "arguments": { "device": "ne2k_pci,id=nic.1,netdev=net.1" } }
We need to split up the device string into a full JSON object
{ "execute": "device_add", "arguments": { "driver": "ne2k_pci", "id": "nic.1", "netdev": "net.1" } }
* src/qemu/qemu_conf.h, src/qemu/qemu_conf.c: Rename the
qemuCommandLineParseKeywords method to qemuParseKeywords
and export it to monitor
* src/qemu/qemu_monitor_json.c: Split up device string into
a JSON object for device_add command
Instead of reporting VIR_ERR_INTERNAL_ERROR use the more specific
VIR_ERR_CONFIG_UNSUPPORTED
* src/qemu/qemu_conf.c: Report VIR_ERR_CONFIG_UNSUPPORTED for
unsupported video adapters
To avoid race-conditions, the tear down of a filter has to happen before
the tap interface disappears and another tap interface with the same
name can re-appear. This patch tries to fix this. In one place, where
communication with the qemu monitor may fail, I am only tearing the
filters down after knowing that the function did not fail.
I am also moving the tear down functions into an include file for other
drivers to reuse.
When qemu libvirt driver doesn't support guest CPU selection with given
qemu binary, guests requiring specific CPU should fail to start instead
of being silently supplied with a default CPU.
The clock timer XML is being updated in the following ways (based on
further off-list discussion that was missed during the initial
implementation):
1) 'wallclock' is changed to 'track', and the possible values are 'boot'
(corresponds to old 'host'), 'guest', and 'wall'.
2) 'mode' has an additional value 'smpsafe'
3) when tickpolicy='catchup', there can be an optional sub-element of
timer called 'catchup':
<catchup threshold=123 slew=120 limit=10000/>
Those three values are all longs, always optional, and if they are present,
they are positive. Internally, 0 indicates "unspecified".
* docs/schemas/domain.rng: updated RNG definition to account for changes
* src/conf/domain_conf.h: change the C struct and enums to match changes.
* src/conf/domain_conf.c: timer parse and format functions changed to
handle the new selections and new element.
* src/libvirt_private.syms: *TimerWallclock* changes to *TimerTrack*
* src/qemu/qemu_conf.c: again, account for Wallclock --> Track change.
virStrToLong* guarantees (via strtol) that the end pointer will be set
to the point at which parsing stopped (even on failure, this point is
the start of the input string).
* src/esx/esx_driver.c (esxGetVersion): Remove pointless
conditional.
* src/qemu/qemu_conf.c (qemuParseCommandLinePCI)
(qemuParseCommandLineUSB, qemuParseCommandLineSmp): Likewise.
* src/qemu/qemu_monitor_text.c
(qemuMonitorTextGetMigrationStatus): Likewise.
Since the timers are defined to cover all possible config cases for
several different hypervisors, many of these possibilities generate an
error on qemu. Here is what is currently supported:
RTC: If the -rtc commandline option is available, allow setting
"clock=host"
or "clock=vm" based on the rtc timer clock='host|guest' value. Also
add "driftfix=slew" if the tickpolicy is 'catchup', or add nothing
if
tickpolicy is 'delay'. (Other tickpolicies will raise an error).
If -rtc isn't available, but -rtc-td-hack is, add that option
if the tickpolicy is 'catchup', add -rtc-td-hack, if it is 'delay'
add nothing, and if it's anything else, raise an error.
PIT: If -no-kvm-pit-reinjection is available, and tickpolicy is
'delay', add that option. if tickpolicy is 'catchup', do
nothing. Anything else --> raise an error.
If -no-kvm-pit-reinjection *isn't* available, but -tdf is, when
tickpolicy is 'catchup' add -tdf. If it's 'delay', do
nothing. Anything else --> raise an error.
If neither of those commandline options is available, and
tickpolicy is anything other than 'delay' (or unspecified), raise
an error.
HPET: If -no-hpet flag is available and present='no', add -no-hpet.
If -no-hpet is not available, and present='yes', raise an error.
If present is unspecified, the default is to do whatever this
particular qemu does by default, so don't raise an error.
All other timer types are unsupported by QEMU, so they will raise an
error.
* src/qemu/qemu_conf.c: extend qemuBuildClockArgStr() to generate the
command line arguments for the new options
* src/qemu/qemu_conf.h: define 4 new flags
* src/qemu/qemu_conf.c: check the help text of qemu for presence of
features indicated by each flag.
* tests/qemuhelptest.c: add appropriate flags into the masks for each test
* Fixes per feedback from Dan and Daniel
* Added test datafiles
* Re-disabled JSON flags
* Added code to print the error policy attribute when generating XML
* Re-add empty tag
Add support for Qemu to have firewall rules applied and removed on VM
startup and shutdown respectively. This patch also provides support for
the updating of a filter that causes all VMs that reference the filter
to have their ebtables/iptables rules updated.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
To find out where the net type 'direct' needs to be handled I introduced
the 'enum virDomainNetType' in the virDomainNetDef structure and let the
compiler tell me where the case statement is missing. Then I added the
unhandled device statement to the UML driver.
* src/conf/domain_conf.h: change _virDomainNetDef type from int to
virDomainNetType enum
* src/conf/domain_conf.c src/lxc/lxc_driver.c src/qemu/qemu_conf.c
src/uml/uml_conf.c: make sure all enum cases are properly handled
in switches
Before, this function would blindly accept an invalid def->dst
and then abuse the idx=-1 it would get from virDiskNameToIndex,
when passing it invalid strings like "xvda:disk" and "sda1".
Now, this function returns -1 upon failure.
* src/conf/domain_conf.c (virDomainDiskDefAssignAddress): as above.
Update callers.
* src/conf/domain_conf.h: Update prototype.
* src/qemu/qemu_conf.c: Update callers.
Attempt to turn on vhost-net mode for devices of type NETWORK, BRIDGE,
and DIRECT (macvtap).
* src/qemu/qemu_conf.h: add vhostfd to qemuBuildHostNetStr prototype
add qemudOpenVhostNet prototype new flag to set when :,vhost=" found in
qemu help
* src/qemu/qemu_conf.c: * set QEMUD_CMD_FLAG_VNET_HOST is ",vhost=" found
in qemu help
- qemudOpenVhostNet - opens /dev/vhost-net to pass to qemu if everything
is in place to use it.
- qemuBuildHostNetStr - add vhostfd to commandline if it's not empty
(higher levels decide whether or not to fill it in)
- qemudBuildCommandLine - if /dev/vhost-net is successfully opened, add
its fd to tapfds array so it isn't closed on qemu exec, and populate
vhostfd_name to be passed in to commandline builder.
* src/qemu/qemu_driver.c: add filler 0 for new arg to qemuBuildHostNetStr,
along with a note that this must be implemented in order for hot-plug of
vhost-net virtio devices to work properly (once qemu "netdev_add" monitor
command is implemented).
* src/qemu/qemu_conf.c: add the ",readonly=on" for read-only disks
and also parse it back in qemuParseCommandLineDisk()
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.args
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.xml:
add a specific regression test
A few more non-literal format strings in error log messages have crept
in. Fix them in the standard way - turn the format string into "%s"
with the original string as the arg.
A number of the error messages raised when parsing USB devices
refered to PCI devices by mistake
* src/qemu/qemu_conf.c: s/PCI/USB/ in qemuParseCommandLineUSB()
Allow an arbitrary timezone with QEMU by setting the $TZ environment
variable when launching QEMU
* src/qemu/qemu_conf.c: Set TZ environment variable if a timezone
is requested
* tests/qemuxml2argvtest.c: Add test case for timezones
* tests/qemuxml2argvdata/qemuxml2argv-clock-france.xml,
tests/qemuxml2argvdata/qemuxml2argv-clock-france.args: Data
for timezone tests
This allows QEMU guests to be started with an arbitrary clock
offset
The test case can't actually be enabled, since QEMU argv expects
an absolute timestring, and this will obviously change every
time the test runs :-( Hopefully QEMU will allow a relative
time offset in the future.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Use the -rtc arg
if available to support variable clock offset mode
* tests/qemuhelptest.c: Add QEMUD_CMD_FLAG_RTC for qemu 0.12.1
* qemuxml2argvdata/qemuxml2argv-clock-variable.args,
qemuxml2argvdata/qemuxml2argv-clock-variable.xml,
qemuxml2argvtest.c: Test case, except we can't actually enable
it yet.
The XML will soon be extended to allow more than just a simple
localtime/utc boolean flag. This change replaces the plain
'int localtime' with a separate struct to prepare for future
extension
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add a new
virDomainClockDef structure
* src/libvirt_private.syms: Export virDomainClockOffsetTypeToString
and virDomainClockOffsetTypeFromString
* src/qemu/qemu_conf.c, src/vbox/vbox_tmpl.c, src/xen/xend_internal.c,
src/xen/xm_internal.c: Updated to use new structure for localtime
This patch sets or unsets the IFF_VNET_HDR flag depending on what device
is used in the VM. The manipulation of the flag is done in the open
function and is only fatal if the IFF_VNET_HDR flag could not be cleared
although it has to be (or if an ioctl generally fails). In that case the
macvtap tap is closed again and the macvtap interface torn.
* src/qemu/qemu_conf.c src/qemu/qemu_conf.h: pass qemuCmdFlags to
qemudPhysIfaceConnect()
* src/util/macvtap.c src/util/macvtap.h: add vnet_hdr boolean to
openMacvtapTap(), and private function configMacvtapTap()
* src/qemu/qemu_driver.c: add extra qemuCmdFlags when calling
qemudPhysIfaceConnect()
Support virtio-serial controller and virtio channel in QEMU backend.
Will output
the following for virtio-serial controller:
-device
virtio-serial-pci,id=virtio-serial0,bus=pci.0,addr=0x4,max_ports=16,vectors=4
and the following for a virtio channel:
-chardev pty,id=channel0 \
-device
virtserialport,bus=virtio-serial0.0,chardev=channel0,name=org.linux-kvm.port.0
* src/qemu/qemu_conf.c: Add argument output for virtio
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args: Add test for
QEMU command line generation
Add support for virtio-serial by defining a new 'virtio' channel target type
and a virtio-serial controller. Allows the following to be specified in a
domain:
<controller type='virtio-serial' index='0' ports='16' vectors='4'/>
<channel type='pty'>
<target type='virtio' name='org.linux-kvm.port.0'/>
<address type='virtio-serial' controller='0' bus='0'/>
</channel>
* docs/schemas/domain.rng: Add virtio-serial controller and virtio
channel type.
* src/conf/domain_conf.[ch]: Domain parsing/serialization for
virtio-serial controller and virtio channel.
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: add domain xml
parsing test
* src/libvirt_private.syms src/qemu/qemu_conf.c:
virDomainDefAddDiskControllers() renamed to
virDomainDefAddImplicitControllers()
Currently we just error with ex. 'virbr0: No such device'.
Since we are using public API calls here, we need to ensure that any
raised error is properly saved and restored, since API entry points
always reset messages.
Rework and simplification of teardown of the macvtap device.
Basically all devices with the same MAC address and link device are kept
alive and not attempted to be torn down. If a macvtap device linked to a
physical interface with a certain MAC address 'M' is to be created it
will automatically fail if the interface is 'up'ed and another macvtap
with the same properties (MAC addr 'M', link dev) happens to be 'up'.
This will prevent the VM from starting or the device from being attached
to a running VM. Stale interfaces are assumed to be there for some
reason and not stem from libvirt.
In the VM shutdown path, it's assuming that an interface name is always
available so that if the device type is DIRECT it can be torn down
using its name.
* src/util/macvtap.h src/libvirt_macvtap.syms: change of deleting routine
* src/util/macvtap.c: cleanups and change of deleting routine
* src/qemu/qemu_driver.c: change cleanup on shutdown
* src/qemu/qemu_conf.c: don't delete Macvtap in qemudPhysIfaceConnect()
A typo in the check for the primary IDE controller could cause
a crash on restore depending on the exact guest config.
* src/qemu/qemu_conf.c: Fix s/video/controller/ typo & slot
number typo
This part adds support for qemu making a macvtap tap device available
via file descriptor passed to qemu command line. This also attempts to
tear down the macvtap device when a VM terminates. This includes support
for attachment and detachment to/from running VM.
* src/qemu/qemu_conf.[ch] src/qemu/qemu_driver.c: add support in the
QEmu driver
All other libvirt functions use array first and then number of elements
in that array. Let's make cpuDecode follow this rule.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
