I hit this problem recently when trying to create a bridge with an IPv6
address on a 3.2 kernel: dnsmasq (and, further, radvd) would not bind to
the given address, waiting 20s and then giving up with -EADDRNOTAVAIL
(resp. exiting immediately with "error parsing or activating the config
file", without libvirt noticing it, BTW). This can be reproduced with (I
think) any kernel >= 2.6.39 and the following XML (to be used with
"virsh net-create"):
<network>
<name>test-bridge</name>
<bridge name='testbr0' />
<ip family='ipv6' address='fd00::1' prefix='64'>
</ip>
</network>
(it happens even when you have an IPv4, too)
The problem is that since commit [1] (which, ironically, was made to
“help IPv6 autoconfiguration”) the linux bridge code makes bridges
behave like “real” devices regarding carrier detection. This makes the
bridges created by libvirt, which are started without any up devices,
stay with the NO-CARRIER flag set, and thus prevents DAD (Duplicate
address detection) from happening, thus letting the IPv6 address flagged
as “tentative”. Such addresses cannot be bound to (see RFC 2462), so
dnsmasq fails binding to it (for radvd, it detects that "interface XXX
is not RUNNING", thus that "interface XXX does not exist, ignoring the
interface" (sic)). It seems that this behavior was enhanced somehow with
commit [2] by avoiding setting NO-CARRIER on empty bridges, but I
couldn't reproduce this behavior on my kernel. Anyway, with the “dummy
tap to set MAC address” trick, this wouldn't work.
To fix this, the idea is to get the bridge's attached device to be up so
that DAD can happen (deactivating DAD altogether is not a good idea, I
think). Currently, libvirt creates a dummy TAP device to set the MAC
address of the bridge, keeping it down. But even if we set this device
up, it is not RUNNING as soon as the tap file descriptor attached to it
is closed, thus still preventing DAD. So, we must modify the API a bit,
so that we can get the fd, keep the tap device persistent, run the
daemons, and close it after DAD has taken place. After that, the bridge
will be flagged NO-CARRIER again, but the daemons will be running, even
if not happy about the device's state (but we don't really care about
the bridge's daemons doing anything when no up interface is connected to
it).
Other solutions that I envisioned were:
* Keeping the *-nic interface up: this would waste an fd for each
bridge during all its life. May be acceptable, I don't really
know.
* Stop using the dummy tap trick, and set the MAC address directly
on the bridge: it is possible since quite some time it seems,
even if then there is the problem of the bridge not being
RUNNING when empty, contrary to what [2] says, so this will need
fixing (and this fix only happened in 3.1, so it wouldn't work
for 2.6.39)
* Using the --interface option of dnsmasq, but I saw somewhere
that it's not used by libvirt for backward compatibility. I am
not sure this would solve this problem, though, as I don't know
how dnsmasq binds itself to it with this option.
This is why this patch does what's described earlier.
This patch also makes radvd start even if the interface is
“missing” (i.e. it is not RUNNING), as it daemonizes before binding to
it, and thus sometimes does it after the interface has been brought down
by us (by closing the tap fd), and then originally stops. This also
makes it stop yelling about it in the logs when the interface is down at
a later time.
[1]
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=1faa4356a3bd89ea11fb92752d897cff3a20ec0e
[2]
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=b64b73d7d0c480f75684519c6134e79d50c1b341
There are a number of process related functions spread
across multiple files. Start to consolidate them by
creating a virprocess.{c,h} file
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
https://www.gnu.org/licenses/gpl-howto.html recommends that
the 'If not, see <url>.' phrase be a separate sentence.
* tests/securityselinuxhelper.c: Remove doubled line.
* tests/securityselinuxtest.c: Likewise.
* globally: s/; If/. If/
This bug was revealed by the crash described in
https://bugzilla.redhat.com/show_bug.cgi?id=852383
The vlan info pointer sent to virNetDevOpenvswitchAddPort should never
be non-NULL unless there is at least one tag. The factthat such a vlan
info pointer was receveid pointed out that a caller was passing the
wrong pointer. Instead of sending &net->vlan, the result of
virDomainNetGetActualVlan(net) should be sent - that function will
look for vlan info in net->data.network.actual->vlan, and in cany case
return NULL instead of a pointer if the vlan info it finds has no
tags.
Aside from causing the crash, sending a hardcoded &net->vlan has the
effect of ignoring vlan info from a <network> or <portgroup> config.
Add the ability to support VLAN tags for Open vSwitch virtual port
types. To accomplish this, modify virNetDevOpenvswitchAddPort and
virNetDevTapCreateInBridgePort to take a virNetDevVlanPtr
argument. When adding the port to the OVS bridge, setup either a
single VLAN or a trunk port based on the configuration from the
virNetDevVlanPtr.
Signed-off-by: Kyle Mestery <kmestery@cisco.com>
As the consensus in:
https://www.redhat.com/archives/libvir-list/2012-July/msg01692.html,
this patch is to destroy conf/virdomainlist.[ch], folding the
helpers into conf/domain_conf.[ch].
* src/Makefile.am:
- Various indention fixes incidentally
- Add macro DATATYPES_SOURCES (datatypes.[ch])
- Link datatypes.[ch] for libvirt_lxc
* src/conf/domain_conf.c:
- Move all the stuffs from virdomainlist.c into it
- Use virUnrefDomain and virUnrefDomainSnapshot instead of
virDomainFree and virDomainSnapshotFree, which are defined
in libvirt.c, and we don't want to link to it.
- Remove "if" before "free" the object, as virObjectUnref
is in the list "useless_free_options".
* src/conf/domain_conf.h:
- Move all the stuffs from virdomainlist.h into it
- s/LIST_FILTER/LIST_DOMAINS_FILTER/
* src/libxl/libxl_driver.c:
- s/LIST_FILTER/LIST_DOMAINS_FILTER/
- no (include "virdomainlist.h")
* src/libxl/libxl_driver.c: Likewise
* src/lxc/lxc_driver.c: Likewise
* src/openvz/openvz_driver.c: Likewise
* src/parallels/parallels_driver.c: Likewise
* src/qemu/qemu_driver.c: Likewise
* src/test/test_driver.c: Likewise
* src/uml/uml_driver.c: Likewise
* src/vbox/vbox_tmpl.c: Likewise
* src/vmware/vmware_driver.c: Likewise
* tools/virsh-domain-monitor.c: Likewise
* tools/virsh.c: Likewise
The meat of this patch is just moving the calls to
virNWFilterRegisterCallbackDriver from each hypervisor's "register"
function into its "initialize" function. The rest is just code
movement to allow that, and a new virNWFilterUnRegisterCallbackDriver
function to undo what the register function does.
The long explanation:
There is an array in nwfilter called callbackDrvArray that has
pointers to a table of functions for each hypervisor driver that are
called by nwfilter. One of those function pointers is to a function
that will lock the hypervisor driver. Entries are added to the table
by calling each driver's "register" function, which happens quite
early in libvirtd's startup.
Sometime later, each driver's "initialize" function is called. This
function allocates a driver object and stores a pointer to it in a
static variable that was previously initialized to NULL. (and here's
the important part...) If the "initialize" function fails, the driver
object is freed, and that pointer set back to NULL (but the entry in
nwfilter's callbackDrvArray is still there).
When the "lock the driver" function mentioned above is called, it
assumes that the driver was successfully loaded, so it blindly tries
to call virMutexLock on "driver->lock".
BUT, if the initialize never happened, or if it failed, "driver" is
NULL. And it just happens that "lock" is always the first field in
driver so it is also NULL.
Boom.
To fix this, the call to virNWFilterRegisterCallbackDriver for each
driver shouldn't be called until the end of its (*already guaranteed
successful*) "initialize" function, not during its "register" function
(which is currently the case). This implies that there should also be
a virNWFilterUnregisterCallbackDriver() function that is called in a
driver's "shutdown" function (although in practice, that function is
currently never called).
Per the FSF address could be changed from time to time, and GNU
recommends the following now: (http://www.gnu.org/licenses/gpl-howto.html)
You should have received a copy of the GNU General Public License
along with Foobar. If not, see <http://www.gnu.org/licenses/>.
This patch removes the explicit FSF address, and uses above instead
(of course, with inserting 'Lesser' before 'General').
Except a bunch of files for security driver, all others are changed
automatically, the copyright for securify files are not complete,
that's why to do it manually:
src/security/security_selinux.h
src/security/security_driver.h
src/security/security_selinux.c
src/security/security_apparmor.h
src/security/security_apparmor.c
src/security/security_driver.c
When sending SIGHUP to libvirtd, it will trigger the virStateDriver
reload operation. This is intended to reload the configuration files
for guests. For unknown historical reasons this is also triggering
autostart of all guests. Autostart is generally expected to be
something that happens on OS startup. Starting VMs on SIGHUP will
violate that expectation and potentially cause dangerous scenarios
if the admin has explicitly shutdown a misbehaving VM that has
been marked as autostart
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Introduce new members in the virMacAddr 'class'
- virMacAddrSet: set virMacAddr from a virMacAddr
- virMacAddrSetRaw: setting virMacAddr from raw 6 byte MAC address buffer
- virMacAddrGetRaw: writing virMacAddr into raw 6 byte MAC address buffer
- virMacAddrCmp: comparing two virMacAddr
- virMacAddrCmpRaw: comparing a virMacAddr with a raw 6 byte MAC address buffer
then replace raw MAC addresses by replacing
- 'unsigned char *' with virMacAddrPtr
- 'unsigned char ... [VIR_MAC_BUFLEN]' with virMacAddr
and introduce usage of above functions where necessary.
This patch adds support for listing all domains into drivers that use
the common virDomainObj implementation: libxl, lxc, openvz, qemu, test,
uml, vmware.
For drivers that don't support managed save images the guests are
treated as if they had none, so filtering guests that do have such an
image on this driver succeeds and produces 0 results.
Remove the uid param from virGetUserConfigDirectory,
virGetUserCacheDirectory, virGetUserRuntimeDirectory,
and virGetUserDirectory
These functions were universally called with the
results of getuid() or geteuid(). To make it practical
to port to Win32, remove the uid parameter and hardcode
geteuid()
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
When the last reference to a virConnectPtr is released by
libvirtd, it was possible for a deadlock to occur in the
virDomainEventState functions. The virDomainEventStatePtr
holds a reference on virConnectPtr for each registered
callback. When removing a callback, the virUnrefConnect
function is run. If this causes the last reference on the
virConnectPtr to be released, then virReleaseConnect can
be run, which in turns calls qemudClose. This function has
a call to virDomainEventStateDeregisterConn which is intended
to remove all callbacks associated with the virConnectPtr
instance. This will try to grab a lock on virDomainEventState
but this lock is already held. Deadlock ensues
Thread 1 (Thread 0x7fcbb526a840 (LWP 23185)):
Since each callback associated with a virConnectPtr holds a
reference on virConnectPtr, it is impossible for the qemudClose
method to be invoked while any callbacks are still registered.
Thus the call to virDomainEventStateDeregisterConn must in fact
be a no-op. Thus it is possible to just remove all trace of
virDomainEventStateDeregisterConn and avoid the deadlock.
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Delete virDomainEventStateDeregisterConn
* src/libxl/libxl_driver.c, src/lxc/lxc_driver.c,
src/qemu/qemu_driver.c, src/uml/uml_driver.c: Remove
calls to virDomainEventStateDeregisterConn
As defined in:
http://standards.freedesktop.org/basedir-spec/basedir-spec-latest.html
This offers a number of advantages:
* Allows sharing a home directory between different machines, or
sessions (eg. using NFS)
* Cleanly separates cache, runtime (eg. sockets), or app data from
user settings
* Supports performing smart or selective migration of settings
between different OS versions
* Supports reseting settings without breaking things
* Makes it possible to clear cache data to make room when the disk
is filling up
* Allows us to write a robust and efficient backup solution
* Allows an admin flexibility to change where data and settings are stored
* Dramatically reduces the complexity and incoherence of the
system for administrators
The code is splattered with a mix of
sizeof foo
sizeof (foo)
sizeof(foo)
Standardize on sizeof(foo) and add a syntax check rule to
enforce it
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This patch will allow OpenFlow controllers to identify which interface
belongs to a particular VM by using the Domain UUID.
ovs-vsctl get Interface vnet0 external_ids
{attached-mac="52:54:00:8C:55:2C", iface-id="83ce45d6-3639-096e-ab3c-21f66a05f7fa", iface-status=active, vm-id="142a90a7-0acc-ab92-511c-586f12da8851"}
V2 changes:
Replaced vm-uuid with vm-id. There was a discussion in Open vSwitch
mailinglist that we should stick with the same DB key postfixes for the
sake of consistency (e.g iface-id, vm-id ...).
Using 'unsigned long' for memory values is risky on 32-bit platforms,
as a PAE guest can have more than 4GiB memory. Our API is
(unfortunately) locked at 'unsigned long' and a scale of 1024, but
the rest of our system should consistently use 64-bit values,
especially since the previous patch centralized overflow checking.
* src/conf/domain_conf.h (_virDomainDef): Always use 64-bit values
for memory. Change hugepage_backed to a bool.
* src/conf/domain_conf.c (virDomainDefParseXML)
(virDomainDefCheckABIStability, virDomainDefFormatInternal): Fix
clients.
* src/vmx/vmx.c (virVMXFormatConfig): Likewise.
* src/xenxs/xen_sxpr.c (xenParseSxpr, xenFormatSxpr): Likewise.
* src/xenxs/xen_xm.c (xenXMConfigGetULongLong): New function.
(xenXMConfigGetULong, xenXMConfigSetInt): Avoid truncation.
(xenParseXM, xenFormatXM): Fix clients.
* src/phyp/phyp_driver.c (phypBuildLpar): Likewise.
* src/openvz/openvz_driver.c (openvzDomainSetMemoryInternal):
Likewise.
* src/vbox/vbox_tmpl.c (vboxDomainDefineXML): Likewise.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Likewise.
* src/qemu/qemu_process.c (qemuProcessStart): Likewise.
* src/qemu/qemu_monitor.h (qemuMonitorGetBalloonInfo): Likewise.
* src/qemu/qemu_monitor_text.h (qemuMonitorTextGetBalloonInfo):
Likewise.
* src/qemu/qemu_monitor_text.c (qemuMonitorTextGetBalloonInfo):
Likewise.
* src/qemu/qemu_monitor_json.h (qemuMonitorJSONGetBalloonInfo):
Likewise.
* src/qemu/qemu_monitor_json.c (qemuMonitorJSONGetBalloonInfo):
Likewise.
* src/qemu/qemu_driver.c (qemudDomainGetInfo)
(qemuDomainGetXMLDesc): Likewise.
* src/uml/uml_conf.c (umlBuildCommandLine): Likewise.
On 64-bit platforms, unsigned long and unsigned long long are
identical, so we don't have to worry about overflow checks.
On 32-bit platforms, anywhere we narrow unsigned long long back
to unsigned long, we have to worry about overflow; it's easier
to do this in one place by having most of the code use the same
or wider types, and only doing the narrowing at the last minute.
Therefore, the memory set commands remain unsigned long, and
the memory get command now centralizes the overflow check into
libvirt.c, so that drivers don't have to repeat the work.
This also fixes a bug where xen returned the wrong value on
failure (most APIs return -1 on failure, but getMaxMemory
must return 0 on failure).
* src/driver.h (virDrvDomainGetMaxMemory): Use long long.
* src/libvirt.c (virDomainGetMaxMemory): Raise overflow.
* src/test/test_driver.c (testGetMaxMemory): Fix driver.
* src/rpc/gendispatch.pl (name_to_ProcName): Likewise.
* src/xen/xen_hypervisor.c (xenHypervisorGetMaxMemory): Likewise.
* src/xen/xen_driver.c (xenUnifiedDomainGetMaxMemory): Likewise.
* src/xen/xend_internal.c (xenDaemonDomainGetMaxMemory):
Likewise.
* src/xen/xend_internal.h (xenDaemonDomainGetMaxMemory):
Likewise.
* src/xen/xm_internal.c (xenXMDomainGetMaxMemory): Likewise.
* src/xen/xm_internal.h (xenXMDomainGetMaxMemory): Likewise.
* src/xen/xs_internal.c (xenStoreDomainGetMaxMemory): Likewise.
* src/xen/xs_internal.h (xenStoreDomainGetMaxMemory): Likewise.
* src/xenapi/xenapi_driver.c (xenapiDomainGetMaxMemory):
Likewise.
* src/esx/esx_driver.c (esxDomainGetMaxMemory): Likewise.
* src/libxl/libxl_driver.c (libxlDomainGetMaxMemory): Likewise.
* src/qemu/qemu_driver.c (qemudDomainGetMaxMemory): Likewise.
* src/lxc/lxc_driver.c (lxcDomainGetMaxMemory): Likewise.
* src/uml/uml_driver.c (umlDomainGetMaxMemory): Likewise.
This is the new interface type that sets up an SR-IOV PCI network
device to be assigned to the guest with PCI passthrough after
initializing some network device-specific things from the config
(e.g. MAC address, virtualport profile parameters). Here is an example
of the syntax:
<interface type='hostdev' managed='yes'>
<source>
<address type='pci' domain='0' bus='0' slot='4' function='3'/>
</source>
<mac address='00:11:22:33:44:55'/>
<address type='pci' domain='0' bus='0' slot='7' function='0'/>
</interface>
This would assign the PCI card from bus 0 slot 4 function 3 on the
host, to bus 0 slot 7 function 0 on the guest, but would first set the
MAC address of the card to 00:11:22:33:44:55.
NB: The parser and formatter don't care if the PCI card being
specified is a standard single function network adapter, or a virtual
function (VF) of an SR-IOV capable network adapter, but the upcoming
code that implements the back end of this config will work *only* with
SR-IOV VFs. This is because modifying the mac address of a standard
network adapter prior to assigning it to a guest is pointless - part
of the device reset that occurs during that process will reset the MAC
address to the value programmed into the card's firmware.
Although it's not supported by any of libvirt's hypervisor drivers,
usb network hostdevs are also supported in the parser and formatter
for completeness and consistency. <source> syntax is identical to that
for plain <hostdev> devices, except that the <address> element should
have "type='usb'" added if bus/device are specified:
<interface type='hostdev'>
<source>
<address type='usb' bus='0' device='4'/>
</source>
<mac address='00:11:22:33:44:55'/>
</interface>
If the vendor/product form of usb specification is used, type='usb'
is implied:
<interface type='hostdev'>
<source>
<vendor id='0x0012'/>
<product id='0x24dd'/>
</source>
<mac address='00:11:22:33:44:55'/>
</interface>
Again, the upcoming patch to fill in the backend of this functionality
will log an error and fail with "Unsupported Config" if you actually
try to assign a USB network adapter to a guest using <interface
type='hostdev'> - just use a standard <hostdev> entry in that case
(and also for single-port PCI adapters).
With an additional new bool added to determine whether or not to
discourage the use of the supplied MAC address by the bridge itself,
virNetDevTapCreateInBridgePort had three booleans (well, 2 bools and
an int used as a bool) in the arg list, which made it increasingly
difficult to follow what was going on. This patch combines those three
into a single flags arg, which not only shortens the arg list, but
makes it more self-documenting.
When a tap device for a domain is created and attached to a bridge,
the first byte of the tap device MAC address is set to 0xFE, while the
rest is set to match the MAC address that will be presented to the
guest as its network device MAC address. Setting this high value in
the tap's MAC address discourages the bridge from using the tap
device's MAC address as the bridge's own MAC address (Linux bridges
always take on the lowest numbered MAC address of all attached devices
as their own).
In one case within libvirt, a tap device is created and attached to
the bridge with the intent that its MAC address be taken on by the
bridge as its own (this is used to assure that the bridge has a fixed
MAC address to prevent network outages created by the bridge MAC
address "flapping" as guests are started and stopped). In this case,
the first byte of the mac address is *not* altered to 0xFE.
In the current code, callers to virNetDevTapCreateInBridgePort each
make the MAC address modification themselves before calling, which
leads to code duplication, and also prevents lower level functions
from knowing the real MAC address being used by the guest. The problem
here is that openvswitch bridges must be informed about this MAC
address, or they will be unable to pass traffic to/from the guest.
This patch centralizes the location of the MAC address "0xFE fixup"
into virNetDevTapCreateInBridgePort(), meaning 1) callers of this
function no longer need the extra strange bit of code, and 2)
bitNetDevTapCreateBridgeInPort itself now is called with the guest's
unaltered MAC address, and can pass it on, unmodified, to
virNetDevOpenvswitchAddPort.
There is no other behavioral change created by this patch.
No thanks to 64-bit windows, with 64-bit pid_t, we have to avoid
constructs like 'int pid'. Our API in libvirt-qemu cannot be
changed without breaking ABI; but then again, libvirt-qemu can
only be used on systems that support UNIX sockets, which rules
out Windows (even if qemu could be compiled there) - so for all
points on the call chain that interact with this API decision,
we require a different variable name to make it clear that we
audited the use for safety.
Adding a syntax-check rule only solves half the battle; anywhere
that uses printf on a pid_t still needs to be converted, but that
will be a separate patch.
* cfg.mk (sc_correct_id_types): New syntax check.
* src/libvirt-qemu.c (virDomainQemuAttach): Document why we didn't
use pid_t for pid, and validate for overflow.
* include/libvirt/libvirt-qemu.h (virDomainQemuAttach): Tweak name
for syntax check.
* src/vmware/vmware_conf.c (vmwareExtractPid): Likewise.
* src/driver.h (virDrvDomainQemuAttach): Likewise.
* tools/virsh.c (cmdQemuAttach): Likewise.
* src/remote/qemu_protocol.x (qemu_domain_attach_args): Likewise.
* src/qemu_protocol-structs (qemu_domain_attach_args): Likewise.
* src/util/cgroup.c (virCgroupPidCode, virCgroupKillInternal):
Likewise.
* src/qemu/qemu_command.c(qemuParseProcFileStrings): Likewise.
(qemuParseCommandLinePid): Use pid_t for pid.
* daemon/libvirtd.c (daemonForkIntoBackground): Likewise.
* src/conf/domain_conf.h (_virDomainObj): Likewise.
* src/probes.d (rpc_socket_new): Likewise.
* src/qemu/qemu_command.h (qemuParseCommandLinePid): Likewise.
* src/qemu/qemu_driver.c (qemudGetProcessInfo, qemuDomainAttach):
Likewise.
* src/qemu/qemu_process.c (qemuProcessAttach): Likewise.
* src/qemu/qemu_process.h (qemuProcessAttach): Likewise.
* src/uml/uml_driver.c (umlGetProcessInfo): Likewise.
* src/util/virnetdev.h (virNetDevSetNamespace): Likewise.
* src/util/virnetdev.c (virNetDevSetNamespace): Likewise.
* tests/testutils.c (virtTestCaptureProgramOutput): Likewise.
* src/conf/storage_conf.h (_virStoragePerms): Use mode_t, uid_t,
and gid_t rather than int.
* src/security/security_dac.c (virSecurityDACSetOwnership): Likewise.
* src/conf/storage_conf.c (virStorageDefParsePerms): Avoid
compiler warning.
Function xmlParseURI does not remove square brackets around IPv6
address when parsing. One of the solutions is making wrappers around
functions working with xmlURI*. This assures that uri->server will be
always properly assigned and it doesn't have to be changed when used
on some new place in the code.
For this purpose, functions virParseURI and virSaveURI were
added. These function are wrappers around xmlParseURI and xmlSaveUri
respectively.
Also there is one new syntax check function to prohibit these functions
anywhere else.
File changes:
- src/util/viruri.h -- declaration
- src/util/viruri.c -- definition
- src/libvirt_private.syms -- symbol export
- src/Makefile.am -- added source and header files
- cfg.mk -- added sc_prohibit_xmlURI
- all others -- ID name and include fixes
This patch allows libvirt to add interfaces to already
existing Open vSwitch bridges. The following syntax in
domain XML file can be used:
<interface type='bridge'>
<mac address='52:54:00:d0:3f:f2'/>
<source bridge='ovsbr'/>
<virtualport type='openvswitch'>
<parameters interfaceid='921a80cd-e6de-5a2e-db9c-ab27f15a6e1d'/>
</virtualport>
<address type='pci' domain='0x0000' bus='0x00'
slot='0x03' function='0x0'/>
</interface>
or if libvirt should auto-generate the interfaceid use
following syntax:
<interface type='bridge'>
<mac address='52:54:00:d0:3f:f2'/>
<source bridge='ovsbr'/>
<virtualport type='openvswitch'>
</virtualport>
<address type='pci' domain='0x0000' bus='0x00'
slot='0x03' function='0x0'/>
</interface>
It is also possible to pass an optional profileid. To do that
use following syntax:
<interface type='bridge'>
<source bridge='ovsbr'/>
<mac address='00:55:1a:65:a2:8d'/>
<virtualport type='openvswitch'>
<parameters interfaceid='921a80cd-e6de-5a2e-db9c-ab27f15a6e1d'
profileid='test-profile'/>
</virtualport>
</interface>
To create Open vSwitch bridge install Open vSwitch and
run the following command:
ovs-vsctl add-br ovsbr
In preparation for the patch to include Murmurhash3, which
introduces a virhashcode.h and virhashcode.c files, rename
the existing hash.h and hash.c to virhash.h and virhash.c
respectively.
Add a new API virDomainShutdownFlags and define:
VIR_DOMAIN_SHUTDOWN_DEFAULT = 0,
VIR_DOMAIN_SHUTDOWN_ACPI_POWER_BTN = (1 << 0),
VIR_DOMAIN_SHUTDOWN_GUEST_AGENT = (1 << 1),
Also define some flags for the reboot API
VIR_DOMAIN_REBOOT_DEFAULT = 0,
VIR_DOMAIN_REBOOT_ACPI_POWER_BTN = (1 << 0),
VIR_DOMAIN_REBOOT_GUEST_AGENT = (1 << 1),
Although these two APIs currently have the same flags, using
separate enums allows them to expand separately in the future.
Add stub impls of the new API for all existing drivers
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=638633
Although scripts are not used by interfaces of type other than
"ethernet" in qemu, due to the fact that the parser stores the script
name in a union that is only valid when type is ethernet or bridge,
there is no way for anyone except the parser itself to catch the
problem of specifying an interface script for an inappropriate
interface type (by the time the parsed data gets back to the code that
called the parser, all evidence that a script was specified is
forgotten).
Since the parser itself should be agnostic to which type of interface
allows scripts (an example of why: a script specified for an interface
of type bridge is valid for xen domains, but not for qemu domains),
the solution here is to move the script out of the union(s) in the
DomainNetDef, always populate it when specified (regardless of
interface type), and let the driver decide whether or not it is
appropriate.
Currently the qemu, xen, libxml, and uml drivers recognize the script
parameter and do something with it (the uml driver only to report that
it isn't supported). Those drivers have been updated to log a
CONFIG_UNSUPPORTED error when a script is specified for an interface
type that's inappropriate for that particular hypervisor.
(NB: There was earlier discussion of solving this problem by adding a
VALIDATE flag to all libvirt APIs that accept XML, which would cause
the XML to be validated against the RNG files. One statement during
that discussion was that the RNG shouldn't contain hypervisor-specific
things, though, and a proper solution to this problem would require
that (again, because a script for an interface of type "bridge" is
accepted by xen, but not by qemu).
The lifetime of the virDomainEventState object is tied to
the lifetime of the driver, which in stateless drivers is
tied to the lifetime of the virConnectPtr.
If we add & remove a timer when allocating/freeing the
virDomainEventState object, we can get a situation where
the timer still triggers once after virDomainEventState
has been freed. The timeout callback can't keep a ref
on the event state though, since that would be a circular
reference.
The trick is to only register the timer when a callback
is registered with the event state & remove the timer
when the callback is unregistered.
The demo for the bug is to run
while true ; do date ; ../tools/virsh -q -c test:///default 'shutdown test; undefine test; dominfo test' ; done
prior to this fix, it will frequently hang and / or
crash, or corrupt memory
Currently all drivers using domain events need to provide a callback
for handling a timer to dispatch events in a clean stack. There is
no technical reason for dispatch to go via driver specific code. It
could trivially be dispatched directly from the domain event code,
thus removing tedious boilerplate code from all drivers
Also fix the libxl & xen drivers to pass 'true' when creating the
virDomainEventState, since they run inside the daemon & thus always
expect events to be present.
* src/conf/domain_event.c, src/conf/domain_event.h: Internalize
dispatch of events from timer callback
* src/libxl/libxl_driver.c, src/lxc/lxc_driver.c,
src/qemu/qemu_domain.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c: Remove all timer dispatch functions
When registering a callback for a particular event some callers
need to know how many callbacks already exist for that event.
While it is possible to ask for a count, this is not free from
race conditions when threaded. Thus the API for registering
callbacks should return the count of callbacks. Also rename
virDomainEventStateDeregisterAny to virDomainEventStateDeregisterID
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Return count of callbacks when
registering callbacks
* src/libxl/libxl_driver.c, src/libxl/libxl_driver.c,
src/qemu/qemu_driver.c, src/remote/remote_driver.c,
src/remote/remote_driver.c, src/uml/uml_driver.c,
src/vbox/vbox_tmpl.c, src/xen/xen_driver.c: Update
for change in APIs
A preparatory patch for DHCP snooping where we want to be able to
differentiate between a VM's interface using the tuple of
<VM UUID, Interface MAC address>. We assume that MAC addresses could
possibly be re-used between different networks (VLANs) thus do not only
want to rely on the MAC address to identify an interface.
At the current 'final destination' in virNWFilterInstantiate I am leaving
the vmuuid parameter as ATTRIBUTE_UNUSED until the DHCP snooping patches arrive.
(we may not post the DHCP snooping patches for 0.9.9, though)
Mostly this is a pretty trivial patch. On the lowest layers, in lxc_driver
and uml_conf, I am passing the virDomainDefPtr around until I am passing
only the VM's uuid into the NWFilter calls.
This patch cleans up return codes in the nwfilter subsystem.
Some functions in nwfilter_conf.c (validators and formatters) are
keeping their bool return for now and I am converting their return
code to true/false.
All other functions now have failure return codes of -1 and success
of 0.
[I searched for all occurences of ' 1;' and checked all 'if ' and
adapted where needed. After that I did a grep for 'NWFilter' in the source
tree.]
Detected by Coverity. Leak introduced in commit 8866eed.
Two bugs here:
1. logfd wasn't closed on all return paths
2. if we failed to mark a domain autodestroy, then the domain
was not made transient but we still returned success
Signed-off-by: Alex Jia <ajia@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Add the core functions that implement the functionality of the API.
Suspend is done by using an asynchronous mechanism so that we can return
the status to the caller before the host gets suspended. This asynchronous
operation is achieved by suspending the host in a separate thread of
execution. However, returning the status to the caller is only best-effort,
but not guaranteed.
To resume the host, an RTC alarm is set up (based on how long we want to
suspend) before suspending the host. When this alarm fires, the host
gets woken up.
Suspend-to-RAM operation on a host running Linux can take upto more than 20
seconds, depending on the load of the system. (Freezing of tasks, an operation
preceding any suspend operation, is given up after a 20 second timeout).
And Suspend-to-Disk can take even more time, considering the time required
for compaction, creating the memory image and writing it to disk etc.
So, we do not allow the user to specify a suspend duration of less than 60
seconds, to be on the safer side, since we don't want to prematurely declare
failure when we only had to wait for some more time.
Following the renaming of the bridge management APIs, we can now
split the source file into 3 corresponding pieces
* src/util/virnetdev.c: APIs for any type of network interface
* src/util/virnetdevbridge.c: APIs for bridge interfaces
* src/util/virnetdevtap.c: APIs for TAP interfaces
* src/util/virnetdev.c, src/util/virnetdev.h,
src/util/virnetdevbridge.c, src/util/virnetdevbridge.h,
src/util/virnetdevtap.c, src/util/virnetdevtap.h: Copied
from bridge.{c,h}
* src/util/bridge.c, src/util/bridge.h: Split into 3 pieces
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/openvz/openvz_driver.c, src/qemu/qemu_command.c,
src/qemu/qemu_conf.h, src/uml/uml_conf.c, src/uml/uml_conf.h,
src/uml/uml_driver.c: Update #include directives
The existing brXXX APIs in src/util/bridge.h are renamed to
follow one of three different conventions
- virNetDevXXX - operations for any type of interface
- virNetDevBridgeXXX - operations for bridge interfaces
- virNetDevTapXXX - operations for tap interfaces
* src/util/bridge.h, src/util/bridge.c: Rename all APIs
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/qemu/qemu_command.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Update for API renaming
Currently every caller of the brXXX APIs has to store the returned
errno value and then raise an error message. This results in
inconsistent error messages across drivers, additional burden on
the callers and makes the error reporting inaccurate since it is
hard to distinguish different scenarios from 1 errno value.
* src/util/bridge.c: Raise errors instead of returning errnos
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/qemu/qemu_command.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Remove error reporting code
The bridge management APIs in src/util/bridge.c require a brControl
object to be passed around. This holds the file descriptor for the
control socket. This extra object complicates use of the API for
only a minor efficiency gain, which is in turn entirely offset by
the need to fork/exec the brctl command for STP configuration.
This patch removes the 'brControl' object entirely, instead opening
the control socket & closing it again within the scope of each method.
The parameter names for the APIs are also made to consistently use
'brname' for bridge device name, and 'ifname' for an interface
device name. Finally annotations are added for non-NULL parameters
and return check validation
* src/util/bridge.c, src/util/bridge.h: Remove brControl object
and update API parameter names & annotations.
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/uml/uml_conf.h, src/uml/uml_conf.c, src/uml/uml_driver.c,
src/qemu/qemu_command.c, src/qemu/qemu_conf.h,
src/qemu/qemu_driver.c: Remove reference to 'brControl' object
The default console type may vary based on the OS type. ie a Xen
paravirt guests wants a 'xen' console, while a fullvirt guests
wants a 'serial' console.
A plain integer default console type in the capabilities does
not suffice. Instead introduce a callback that is passed the
OS type.
* src/conf/capabilities.h: Use a callback for default console
type
* src/conf/domain_conf.c, src/conf/domain_conf.h: Use callback
for default console type. Add missing LXC/OpenVZ console types.
* src/esx/esx_driver.c, src/libxl/libxl_conf.c,
src/lxc/lxc_conf.c, src/openvz/openvz_conf.c,
src/phyp/phyp_driver.c, src/qemu/qemu_capabilities.c,
src/uml/uml_conf.c, src/vbox/vbox_tmpl.c,
src/vmware/vmware_conf.c, src/xen/xen_hypervisor.c,
src/xenapi/xenapi_driver.c: Set default console type callback
To allow virDomainOpenConsole to access non-primary consoles,
device aliases are required to be set. Until now only the QEMU
driver has done this. Update LXC & UML to set aliases for any
console devices
* src/lxc/lxc_driver.c, src/uml/uml_driver.c: Set aliases
for console devices
While Xen only has a single paravirt console, UML, and
QEMU both support multiple paravirt consoles. The LXC
driver can also be trivially made to support multiple
consoles. This patch extends the XML to allow multiple
<console> elements in the XML. It also makes the UML
and QEMU drivers support this config.
* src/conf/domain_conf.c, src/conf/domain_conf.h: Allow
multiple <console> devices
* src/lxc/lxc_driver.c, src/xen/xen_driver.c,
src/xenxs/xen_sxpr.c, src/xenxs/xen_xm.c: Update for
internal API changes
* src/security/security_selinux.c, src/security/virt-aa-helper.c:
Only label consoles that aren't a copy of the serial device
* src/qemu/qemu_command.c, src/qemu/qemu_driver.c,
src/qemu/qemu_process.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Support multiple console devices
* tests/qemuxml2xmltest.c, tests/qemuxml2argvtest.c: Extra
tests for multiple virtio consoles. Set QEMU_CAPS_CHARDEV
for all console /channel tests
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args
tests/qemuxml2argvdata/qemuxml2argv-console-virtio.args: Update
for correct chardev syntax
* tests/qemuxml2argvdata/qemuxml2argv-console-virtio-many.args,
tests/qemuxml2argvdata/qemuxml2argv-console-virtio-many.xml: New
test file
We recently added support for VIR_DOMAIN_START_AUTODESTROY and
an impl to the QEMU driver. It is very desirable to support in
other drivers, so this adds it to LXC and UML
* src/lxc/lxc_conf.h, src/lxc/lxc_driver.c,
src/uml/uml_conf.h, src/uml/uml_driver.c: Wire up autodestroy
functions
I got confused when 'virsh domblkinfo dom disk' required the
path to a disk (which can be ambiguous, since a single file
can back multiple disks), rather than the unambiguous target
device name that I was using in disk snapshots. So, in true
developer fashion, I went for the best of both worlds - all
interfaces that operate on a disk (aka block) now accept
either the target name or the unambiguous path to the backing
file used by the disk.
* src/conf/domain_conf.h (virDomainDiskIndexByName): Add
parameter.
(virDomainDiskPathByName): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainDiskIndexByName): Also allow
searching by path, and decide whether ambiguity is okay.
(virDomainDiskPathByName): New function.
(virDomainDiskRemoveByName, virDomainSnapshotAlignDisks): Update
callers.
* src/qemu/qemu_driver.c (qemudDomainBlockPeek)
(qemuDomainAttachDeviceConfig, qemuDomainUpdateDeviceConfig)
(qemuDomainGetBlockInfo, qemuDiskPathToAlias): Likewise.
* src/qemu/qemu_process.c (qemuProcessFindDomainDiskByPath):
Likewise.
* src/libxl/libxl_driver.c (libxlDomainAttachDeviceDiskLive)
(libxlDomainDetachDeviceDiskLive, libxlDomainAttachDeviceConfig)
(libxlDomainUpdateDeviceConfig): Likewise.
* src/uml/uml_driver.c (umlDomainBlockPeek): Likewise.
* src/xen/xend_internal.c (xenDaemonDomainBlockPeek): Likewise.
* docs/formatsnapshot.html.in: Update documentation.
* tools/virsh.pod (domblkstat, domblkinfo): Likewise.
* docs/schemas/domaincommon.rng (diskTarget): Tighten pattern on
disk targets.
* docs/schemas/domainsnapshot.rng (disksnapshot): Update to match.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: Update test.
Revert 6a1f5f568f. Now that libvirt_iohelper takes fds by
inheritance rather than by open() (commit 1eb66479), there is
no longer a race where the parent can unlink() a file prior to
the iohelper open()ing the same file. From there, it makes
more sense to have the callers both create and unlink, rather
than the caller create and the stream unlink, since the latter
was only needed when iohelper had to do the unlink.
* src/fdstream.h (virFDStreamOpenFile, virFDStreamCreateFile):
Callers are responsible for deletion.
* src/fdstream.c (virFDStreamOpenFileInternal): Don't leak created
file on failure.
(virFDStreamOpenFile, virFDStreamCreateFile): Drop parameter.
* src/lxc/lxc_driver.c (lxcDomainOpenConsole): Update callers.
* src/qemu/qemu_driver.c (qemuDomainScreenshot)
(qemuDomainOpenConsole): Likewise.
* src/storage/storage_driver.c (storageVolumeDownload)
(storageVolumeUpload): Likewise.
* src/uml/uml_driver.c (umlDomainOpenConsole): Likewise.
* src/vbox/vbox_tmpl.c (vboxDomainScreenshot): Likewise.
* src/xen/xen_driver.c (xenUnifiedDomainOpenConsole): Likewise.
Using a macro ensures that all the code is looking for the same
prefix.
* src/conf/domain_conf.h (VIR_NET_GENERATED_PREFIX): New macro.
* src/conf/domain_conf.c (virDomainNetDefParseXML): Use it.
* src/uml/uml_conf.c (umlConnectTapDevice): Likewise.
* src/qemu/qemu_command.c (qemuNetworkIfaceConnect): Likewise.
Suggested by Laine Stump.
Without this, a configure built by autoconf 2.59 was broken when
trying to detect which compiler warning flags were supported.
* .gnulib: Update to latest, for warnings.m4 fix.
* bootstrap.conf: Add fclose explicitly, to match recent gnulib
implicit dependency changes.
* src/qemu/qemu_conf.c (includes): Drop unused include.
* src/uml/uml_conf.c (include): Likewise.
Reported by Daniel P. Berrange.
The previous patches only cleaned up ATTRIBUTE_UNUSED flags cases;
auditing the drivers found other places where flags was being used
but not validated. In particular, domainGetXMLDesc had issues with
clients accepting a different set of flags than the common
virDomainDefFormat helper function.
* src/conf/domain_conf.c (virDomainDefFormat): Add common flag check.
* src/uml/uml_driver.c (umlDomainAttachDeviceFlags)
(umlDomainDetachDeviceFlags): Reject unknown
flags.
* src/vbox/vbox_tmpl.c (vboxDomainGetXMLDesc)
(vboxDomainAttachDeviceFlags)
(vboxDomainDetachDeviceFlags): Likewise.
* src/qemu/qemu_driver.c (qemudDomainMemoryPeek): Likewise.
(qemuDomainGetXMLDesc): Document common flag handling.
* src/libxl/libxl_driver.c (libxlDomainGetXMLDesc): Likewise.
* src/lxc/lxc_driver.c (lxcDomainGetXMLDesc): Likewise.
* src/openvz/openvz_driver.c (openvzDomainGetXMLDesc): Likewise.
* src/phyp/phyp_driver.c (phypDomainGetXMLDesc): Likewise.
* src/test/test_driver.c (testDomainGetXMLDesc): Likewise.
* src/vmware/vmware_driver.c (vmwareDomainGetXMLDesc): Likewise.
* src/xenapi/xenapi_driver.c (xenapiDomainGetXMLDesc): Likewise.
No need to repeat common code.
* bootstrap.conf (gnulib_modules): Import calloc-posix.
* src/util/bridge.c (brInit): Use virSetCloseExec.
(brSetInterfaceUp): Adjust flags name.
* src/uml/uml_driver.c (umlSetCloseExec): Delete.
(umlStartVMDaemon): Use util version instead.
The UML inotify handler would kill off guests when certain
conditions arise, but it forgot to remove transient guests
from the list of domains
* src/uml/uml_driver.c: Cleanup transient guests
The drivers were accepting domain configs without checking if those
were actually meant for them. For example the LXC driver happily
accepts configs with type QEMU.
Add a check for the expected domain types to the virDomainDefParse*
functions.
Some callers expected virFileMakePath to set errno, some expected
it to return an errno value. Unify this to return 0 on success and
-1 on error. Set errno to report detailed error information.
Also optimize virFileMakePath if stat fails with an errno different
from ENOENT.
To avoid regressions, we let callers specify whether to require a
minor and micro version. Callers that were parsing uname() output
benefit from defaulting to 0, whereas callers that were parsing
version strings from other sources should not change in behavior.
* src/util/util.c (virParseVersionString): Allow caller to choose
whether to fail if minor or micro is missing.
* src/util/util.h (virParseVersionString): Update signature.
* src/esx/esx_driver.c (esxGetVersion): Update callers.
* src/lxc/lxc_driver.c (lxcVersion): Likewise.
* src/openvz/openvz_conf.c (openvzExtractVersionInfo): Likewise.
* src/uml/uml_driver.c (umlGetVersion): Likewise.
* src/vbox/vbox_MSCOMGlue.c (vboxLookupVersionInRegistry):
Likewise.
* src/vbox/vbox_tmpl.c (vboxExtractVersion): Likewise.
* src/vmware/vmware_conf.c (vmwareExtractVersion): Likewise.
* src/xenapi/xenapi_driver.c (xenapiGetVersion): Likewise.
Reported by Matthias Bolte.
Since we virEventRegisterDefaultImpl is now a public API, callers need
a way to invoke the default registered Handle and Timeout functions. We
already have general functions for these internally, so promote
them to the public API.
v2:
Actually add APIs to libvirt.h
This patch deprecates following enums:
VIR_DOMAIN_MEM_CURRENT
VIR_DOMAIN_MEM_LIVE
VIR_DOMAIN_MEM_CONFIG
VIR_DOMAIN_VCPU_LIVE
VIR_DOMAIN_VCPU_CONFIG
VIR_DOMAIN_DEVICE_MODIFY_CURRENT
VIR_DOMAIN_DEVICE_MODIFY_LIVE
VIR_DOMAIN_DEVICE_MODIFY_CONFIG
And modify internal codes to use virDomainModificationImpact.
Change all the driver struct initializers to use the
C99 style, leaving out unused fields. This will make
it possible to add new APIs without changing every
driver. eg change:
qemudDomainResume, /* domainResume */
qemudDomainShutdown, /* domainShutdown */
NULL, /* domainReboot */
qemudDomainDestroy, /* domainDestroy */
to
.domainResume = qemudDomainResume,
.domainShutdown = qemudDomainShutdown,
.domainDestroy = qemudDomainDestroy,
And get rid of any existing C99 style initializersr which
set NULL, eg change
.listPools = vboxStorageListPools,
.numOfDefinedPools = NULL,
.listDefinedPools = NULL,
.findPoolSources = NULL,
.poolLookupByName = vboxStoragePoolLookupByName,
to
.listPools = vboxStorageListPools,
.poolLookupByName = vboxStoragePoolLookupByName,
Fix some driver names:
s/virDrvCPUCompare/virDrvCompareCPU/
s/virDrvCPUBaseline/virDrvBaselineCPU/
s/virDrvQemuDomainMonitorCommand/virDrvDomainQemuMonitorCommand/
s/virDrvSecretNumOfSecrets/virDrvNumOfSecrets/
s/virDrvSecretListSecrets/virDrvListSecrets/
And some driver struct field names:
s/getFreeMemory/nodeGetFreeMemory/
Only in drivers which use virDomainObj, drivers that query hypervisor
for domain status need to be updated separately in case their hypervisor
supports this functionality.
The reason is also saved into domain state XML so if a domain is not
running (i.e., no state XML exists) the reason will be lost by libvirtd
restart. I think this is an acceptable limitation.
This is needed if we want to transfer a temporary file. If the
transfer is done with iohelper, we might run into a race condition,
where we unlink() file before iohelper is executed.
* src/fdstream.c, src/fdstream.h,
src/util/iohelper.c: Add new option
* src/lxc/lxc_driver.c, src/qemu/qemu_driver.c,
src/storage/storage_driver.c, src/uml/uml_driver.c,
src/xen/xen_driver.c: Expand existing function calls
These VIR_XXXX0 APIs make us confused, use the non-0-suffix APIs instead.
How do these coversions works? The magic is using the gcc extension of ##.
When __VA_ARGS__ is empty, "##" will swallow the "," in "fmt," to
avoid compile error.
example: origin after CPP
high_level_api("%d", a_int) low_level_api("%d", a_int)
high_level_api("a string") low_level_api("a string")
About 400 conversions.
8 special conversions:
VIR_XXXX0("") -> VIR_XXXX("msg") (avoid empty format) 2 conversions
VIR_XXXX0(string_literal_with_%) -> VIR_XXXX(%->%%) 0 conversions
VIR_XXXX0(non_string_literal) -> VIR_XXXX("%s", non_string_literal)
(for security) 6 conversions
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
This matches the public API and helps to get rid of some special
case code in the remote generator.
Rename driver API functions and XDR protocol structs.
No functional change included outside of the remote generator.
We already have virAsprintf, so picking a similar name helps for
seeing a similar purpose. Furthermore, the prefix V before printf
generally implies 'va_list', even though this variant was '...', and
the old name got in the way of adding a new va_list version.
global rename performed with:
$ git grep -l virBufferVSprintf \
| xargs -L1 sed -i 's/virBufferVSprintf/virBufferAsprintf/g'
then revert the changes in ChangeLog-old.
The O_NONBLOCK flag doesn't work as desired on plain files
or block devices. Introduce an I/O helper program that does
the blocking I/O operations, communicating over a pipe that
can support O_NONBLOCK
* src/fdstream.c, src/fdstream.h: Add non-blocking I/O
on plain files/block devices
* src/Makefile.am, src/util/iohelper.c: I/O helper program
* src/qemu/qemu_driver.c, src/lxc/lxc_driver.c,
src/uml/uml_driver.c, src/xen/xen_driver.c: Update for
streams API change
This simplifies several callers that were repeating checks already
guaranteed by util.c, and makes other callers more robust to now
reject directories. remote_driver.c was over-strict - access(,R_OK)
is only needed to execute a script file; a binary only needs
access(,X_OK) (besides, it's unusual to see a file with x but not
r permissions, whether script or binary).
* cfg.mk (sc_prohibit_access_xok): New syntax-check rule.
(exclude_file_name_regexp--sc_prohibit_access_xok): Exempt one use.
* src/network/bridge_driver.c (networkStartRadvd): Fix offenders.
* src/qemu/qemu_capabilities.c (qemuCapsProbeMachineTypes)
(qemuCapsInitGuest, qemuCapsInit, qemuCapsExtractVersionInfo):
Likewise.
* src/remote/remote_driver.c (remoteFindDaemonPath): Likewise.
* src/uml/uml_driver.c (umlStartVMDaemon): Likewise.
* src/util/hooks.c (virHookCheck): Likewise.
It is possible to set a migration speed limit when starting
migration. This new API allows the speed limit to be changed
on the fly to adjust to changing conditions
* src/driver.h, src/libvirt.c, src/libvirt_public.syms,
include/libvirt/libvirt.h.in: Add virDomainMigrateSetMaxSpeed
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/vmware/vmware_driver.c, src/xen/xen_driver.c,
src/libxl/libxl_driver.c: Stub new API
This patch introduces a new libvirt API (virDomainSetMemoryFlags) and
a flag (virDomainMemoryModFlags).
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Relax the restriction that the hash table key must be a string
by allowing an arbitrary hash code generator + comparison func
to be provided
* util/hash.c, util/hash.h: Allow any pointer as a key
* internal.h: Include stdbool.h as standard.
* conf/domain_conf.c, conf/domain_conf.c,
conf/nwfilter_params.c, nwfilter/nwfilter_gentech_driver.c,
nwfilter/nwfilter_gentech_driver.h, nwfilter/nwfilter_learnipaddr.c,
qemu/qemu_command.c, qemu/qemu_driver.c,
qemu/qemu_process.c, uml/uml_driver.c,
xen/xm_internal.c: s/char */void */ in hash callbacks
An upcoming patch has a use for a tap device to be created that
doesn't need to be actually put into the "up" state, and keeping it
"down" keeps the output of ifconfig from being unnecessarily cluttered
(ifconfig won't show down interfaces unless you add "-a").
bridge.[ch]: add "up" as an arg to brAddTap()
uml_conf.c, qemu_command.c: add "up" (set to "true") to brAddTap() call.
This will allow us to record transient runtime state in vm->def, like
default VNC parameters. Accomplish this by adding an extra 'live' parameter
to SetDefTransient, with similar semantics to the 'live' flag for
AssignDef.
Except LXC and UML driver, implementations of all other drivers
simply return 0, because these drivers doesn't have config both
in memory and on disk, no need to track if the domain of these
drivers updated or not.
Rename "xenUnifiedDomainisPersistent" to "xenUnifiedDomainIsPersistent"
* esx/esx_driver.c
* lxc/lxc_driver.c
* opennebula/one_driver.c
* openvz/openvz_driver.c
* phyp/phyp_driver.c
* test/test_driver.c
* uml/uml_driver.c
* vbox/vbox_tmpl.c
* xen/xen_driver.c
* xenapi/xenapi_driver.c
The current semantics of non-persistent hotplug/update are confusing: the
changes will persist as long as the in memory domain definition isn't
overwritten. This means hotplug changes stay around until the domain is
redefined or libvirtd is restarted.
Call virDomainObjSetDefTransient at VM startup, so that we properly discard
hotplug changes when the VM is shutdown.
Similarly to deprecating close(), I am now deprecating fclose() and
introduce VIR_FORCE_FCLOSE() and VIR_FCLOSE(). Also, fdopen() is replaced with
VIR_FDOPEN().
Most of the files are opened in read-only mode, so usage of
VIR_FORCE_CLOSE() seemed appropriate. Others that are opened in write
mode already had the fclose()< 0 check and I converted those to
VIR_FCLOSE()< 0.
I did not find occurrences of possible double-closed files on the way.
Introduce implementations of the virDomainOpenConsole() API
for LXC, Xen and UML drivers.
* src/lxc/lxc_driver.c, src/lxc/lxc_driver.c,
src/xen/xen_driver.c: Wire up virDomainOpenConsole
To enable virsh console (or equivalent) to be used remotely
it is necessary to provide remote access to the /dev/pts/XXX
pseudo-TTY associated with the console/serial/parallel device
in the guest. The virStream API provide a bi-directional I/O
stream capability that can be used for this purpose. This
patch thus introduces a virDomainOpenConsole API that uses
the stream APIs.
* src/libvirt.c, src/libvirt_public.syms,
include/libvirt/libvirt.h.in, src/driver.h: Define the
new virDomainOpenConsole API
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c, src/xenapi/xenapi_driver.c: Stub
API entry point
Using automated replacement with sed and editing I have now replaced all
occurrences of close() with VIR_(FORCE_)CLOSE() except for one, of
course. Some replacements were straight forward, others I needed to pay
attention. I hope I payed attention in all the right places... Please
have a look. This should have at least solved one more double-close
error.
This is from a bug report and conversation on IRC where Soren reported that while a filter update is occurring on one or more VMs (due to a rule having been edited for example), a deadlock can occur when a VM referencing a filter is started.
The problem is caused by the two locking sequences of
qemu driver, qemu domain, filter # for the VM start operation
filter, qemu_driver, qemu_domain # for the filter update operation
that obviously don't lock in the same order. The problem is the 2nd lock sequence. Here the qemu_driver lock is being grabbed in qemu_driver:qemudVMFilterRebuild()
The following solution is based on the idea of trying to re-arrange the 2nd sequence of locks as follows:
qemu_driver, filter, qemu_driver, qemu_domain
and making the qemu driver recursively lockable so that a second lock can occur, this would then lead to the following net-locking sequence
qemu_driver, filter, qemu_domain
where the 2nd qemu_driver lock has been ( logically ) eliminated.
The 2nd part of the idea is that the sequence of locks (filter, qemu_domain) and (qemu_domain, filter) becomes interchangeable if all code paths where filter AND qemu_domain are locked have a preceding qemu_domain lock that basically blocks their concurrent execution
So, the following code paths exist towards qemu_driver:qemudVMFilterRebuild where we now want to put a qemu_driver lock in front of the filter lock.
-> nwfilterUndefine() [ locks the filter ]
-> virNWFilterTestUnassignDef()
-> virNWFilterTriggerVMFilterRebuild()
-> qemudVMFilterRebuild()
-> nwfilterDefine()
-> virNWFilterPoolAssignDef() [ locks the filter ]
-> virNWFilterTriggerVMFilterRebuild()
-> qemudVMFilterRebuild()
-> nwfilterDriverReload()
-> virNWFilterPoolLoadAllConfigs()
->virNWFilterPoolObjLoad()
-> virNWFilterPoolAssignDef() [ locks the filter ]
-> virNWFilterTriggerVMFilterRebuild()
-> qemudVMFilterRebuild()
-> nwfilterDriverStartup()
-> virNWFilterPoolLoadAllConfigs()
->virNWFilterPoolObjLoad()
-> virNWFilterPoolAssignDef() [ locks the filter ]
-> virNWFilterTriggerVMFilterRebuild()
-> qemudVMFilterRebuild()
Qemu is not the only driver using the nwfilter driver, but also the UML driver calls into it. Therefore qemuVMFilterRebuild() can be exchanged with umlVMFilterRebuild() along with the driver lock of qemu_driver that can now be a uml_driver. Further, since UML and Qemu domains can be running on the same machine, the triggering of a rebuild of the filter can touch both types of drivers and their domains.
In the patch below I am now extending each nwfilter callback driver with functions for locking and unlocking the (VM) driver (UML, QEMU) and introduce new functions for locking all registered callback drivers and unlocking them. Then I am distributing the lock-all-cbdrivers/unlock-all-cbdrivers call into the above call paths. The last shown callpath starting with nwfilterDriverStart() is problematic since it is initialize before the Qemu and UML drives are and thus a lock in the path would result in a NULL pointer attempted to be locked -- the call to virNWFilterTriggerVMFilterRebuild() is never called, so we never lock either the qemu_driver or the uml_driver in that path. Therefore, only the first 3 paths now receive calls to lock and unlock all callback drivers. Now that the locks are distributed where it matters I can remove the qemu_driver and uml_driver lock from qemudVMFilterRebuild() and umlVMFilterRebuild() and not requiring the recursive locks.
For now I want to put this out as an RFC patch. I have tested it by 'stretching' the critical section after the define/undefine functions each lock the filter so I can (easily) concurrently execute another VM operation (suspend,start). That code is in this patch and if you want you can de-activate it. It seems to work ok and operations are being blocked while the update is being done.
I still also want to verify the other assumption above that locking filter and qemu_domain always has a preceding qemu_driver lock.
Adding parsing code for memory tunables in the domain xml file
also change the internal define structures used for domain memory
informations
Adds a new specific test
Public api to set/get memory tunables supported by the hypervisors.
dv:
* some cleanups in libvirt.c
* adding extra checks in libvirt.c new entry points
v4:
* Move exporting public API to this patch
* Add unsigned int flags to the public api for future extensions
v3:
* Add domainGetMemoryParamters and NULL in all the driver interface
v2:
* Initialize domainSetMemoryParameters to NULL in all the driver
interface structure.
When nwfilter support was added to UML, I didn't realise the UML driver
needed instrumentation to make updating nwfilters on the fly work. This
patch adds this bit of glue.
Signed-off-by: Soren Hansen <soren@linux2go.dk>
For privileged UML connections (uml:///system), we shouldn't use root's
home dir, but rather somewhere in /var/run/libvirt/uml-guest.
https://bugzilla.redhat.com/show_bug.cgi?id=499536
Signed-off-by: Soren Hansen <soren@linux2go.dk>
uml_dir overrides user-mode-linux's default of ~/.uml. This is needed
for a couple of different reasons:
libvirt expects this to default to virGetUserDirectory(geteuid()) +
'/.uml'. However, user-mode-linux actually uses the HOME environment
variable to determine where to look for the uml sockets, but if running
libvirtd under sudo (which I routinely do during development), $HOME is
pointing at my user's homedir, while my euid is 0, so libvirt looks in
/root.
Also (and this was my actual motivation for this patch), if HOME isn't
set at all, user-mode-linux utterly fails. Looking at the code, it seems
it's meant to emit a warning, but alas, it doesn't for some reason.
If running libvirtd from upstart, HOME is not set, so any system using
upstart will need this change.
Signed-off-by: Soren Hansen <soren@linux2go.dk>
UML supports hot plugging and unplugging of various devices. This patch
exposes this functionality for disks.
Signed-off-by: Soren Hansen <soren@linux2go.dk>
Like the comment suggested, we just open the file and pass the file
descriptor to uml. The input "stream" is set to "null", since I couldn't
find any useful way to actually use a file for input for a chardev and
this also mimics what e.g. QEmu does internally.
Signed-off-by: Soren Hansen <soren@linux2go.dk>
* src/uml/uml_driver.c (umlMonitorCommand): Validate that enough
bytes were read to dereference both res.length, and that many
bytes from res.data.
Reported by Soren Hansen.
This patch does two things:
* It makes umlConnectTapDevice ask brAddTap for a persistent tap by
passing it a NULL tapfd argument.
* Stops umlConnectTapDevice from immediately dismantling the bridge
it just set up.
Signed-off-by: Soren Hansen <soren@linux2go.dk>
If umlBuildCommandLineChr fails (e.g. due to an unsupported chardev
type), it returns NULL. umlBuildCommandLine does not check for this and
sets this as an argument on the comand line, effectively ending the
argument list. This patch checks for this case and sets the chardev to
"none".
Signed-off-by: Soren Hansen <soren@linux2go.dk>
Added a more detailed error message when adding a tap devices fails and
the kernel is missing tun support.
Signed-off-by: Doug Goldstein <cardoe@gentoo.org>
Fix the error checking to use the return value from brAddTap() instead
of checking the current errno value which might have been changed by
clean up calls inside of brAddTap().
Signed-off-by: Doug Goldstein <cardoe@gentoo.org>
All <console> devices now export a <target> type attribute. QEMU defaults
to 'serial', UML defaults to 'uml, xen can be either 'serial' or 'xen'
depending on fullvirt. Understandably there is lots of test fallout.
This will be used to differentiate between a serial vs. virtio console for
QEMU.
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Add the library entry point for the new virDomainQemuMonitorCommand()
entry point. Because this is not part of the "normal" libvirt API,
it gets its own header file, library file, and will eventually
get its own over-the-wire protocol later in the series.
Changes since v1:
- Go back to using the virDriver table for qemuDomainMonitorCommand, due to
linking issues
- Added versioning information to the libvirt-qemu.so
Changes since v2:
- None
Changes since v3:
- Add LGPL header to libvirt-qemu.c
- Make virLibConnError and virLibDomainError macros instead of function calls
Changes since v4:
- Move exported symbols to libvirt_qemu.syms
Signed-off-by: Chris Lalancette <clalance@redhat.com>
A Linux software bridge will assume the MAC address of the enslaved
interface with the numerically lowest MAC addr. When the bridge
changes MAC address there is a period of network blackout, so a
change should be avoided. The kernel gives TAP devices a completely
random MAC address. Occassionally the random TAP device MAC is lower
than that of the physical interface (eth0, eth1etc) that is enslaved,
causing the bridge to change its MAC.
This change sets an explicit MAC address for all TAP devices created
using the configured MAC from the XML, but with the high byte set
to 0xFE. This should ensure TAP device MACs are higher than any
physical interface MAC.
* src/qemu/qemu_conf.c, src/uml/uml_conf.c: Pass in a MAC addr
for the TAP device with high byte set to 0xFE
* src/util/bridge.c, src/util/bridge.h: Set a MAC when creating
the TAP device to override random MAC
* src/uml/uml_driver.c (umlMonitorCommand): Correct flaw that would
cause unconditional "incomplete reply ..." failure, since "nbytes"
was always 0 or 1.
Otherwise, a malicious packet could cause a DoS via spurious
out-of-memory failure.
* src/uml/uml_driver.c (umlMonitorCommand): Validate that incoming
data is reliable before using it to allocate/dereference memory.
Don't report bogus errno on short read.
Reported by Jim Meyering.
Allow for a host UUID in the capabilities XML. Local drivers
will initialize this from the SMBIOS data. If a sanity check
shows SMBIOS uuid is invalid, allow an override from the
libvirtd.conf configuration file
* daemon/libvirtd.c, daemon/libvirtd.conf: Support a host_uuid
configuration option
* docs/schemas/capability.rng: Add optional host uuid field
* src/conf/capabilities.c, src/conf/capabilities.h: Include
host UUID in XML
* src/libvirt_private.syms: Export new uuid.h functions
* src/lxc/lxc_conf.c, src/qemu/qemu_driver.c,
src/uml/uml_conf.c: Set host UUID in capabilities
* src/util/uuid.c, src/util/uuid.h: Support for host UUIDs
* src/node_device/node_device_udev.c: Use the host UUID functions
* tests/confdata/libvirtd.conf, tests/confdata/libvirtd.out: Add
new host_uuid config option to test
Approximately 60 messages were marked. Since these diagnostics are
intended solely for developers and maintainers, encouraging translation
is deemed to be counterproductive:
http://thread.gmane.org/gmane.comp.emulators.libvirt/25050/focus=25052
Run this command:
git grep -l VIR_WARN|xargs perl -pi -e \
's/(VIR_WARN0?)\s*\(_\((".*?")\)/$1($2/'
This defines the internal driver API and stubs out each driver
* src/driver.h: Define virDrvDomainGetBlockInfo signature
* src/libvirt.c, src/libvirt_public.syms: Glue public API to drivers
* src/esx/esx_driver.c, src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/phyp/phyp_driver.c,
src/test/test_driver.c, src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c, src/xenapi/xenapi_driver.c: Stub out driver
virDomainManagedSave() is to be run on a running domain. Once the call
complete, as in virDomainSave() the domain is stopped upon completion,
but there is no restore counterpart as any order to start the domain
from the API would load the state from the managed file, similary if
the domain is autostarted when libvirtd starts.
Once a domain has restarted his managed save image is destroyed,
basically managed save image can only exist for a stopped domain,
for a running domain that would be by definition outdated data.
* include/libvirt/libvirt.h.in src/libvirt.c src/libvirt_public.syms:
adds the new entry points virDomainManagedSave(),
virDomainHasManagedSaveImage() and virDomainManagedSaveRemove()
* src/driver.h src/esx/esx_driver.c src/lxc/lxc_driver.c
src/opennebula/one_driver.c src/openvz/openvz_driver.c
src/phyp/phyp_driver.c src/qemu/qemu_driver.c src/vbox/vbox_tmpl.c
src/remote/remote_driver.c src/test/test_driver.c src/uml/uml_driver.c
src/xen/xen_driver.c: add corresponding new internal drivers entry
points
virParseVersionString uses virStrToLong_ui instead of sscanf.
This also fixes a bug in the UML driver, that always returned 0
as version number.
Introduce STRSKIP to check if a string has a certain prefix and
to skip this prefix.
When a domain is defined on host1, migrated to host2 and then migrated
back to host1, its current configuration would overwrite the libvirtd's
in-memory copy of persistent configuration of that domain. This is not
desired as we want to preserve the persistent configuration untouched.
This patch introduces new 'live' parameter to virDomainAssignDef.
Passing 'true' for 'live' means the configuration passed to
virDomainAssignDef describes a configuration of live instance of the
domain. This applies for saved domains which are being restored or for
incoming domains during migration.
All callers have been changed to pass the appropriate value.
To find out where the net type 'direct' needs to be handled I introduced
the 'enum virDomainNetType' in the virDomainNetDef structure and let the
compiler tell me where the case statement is missing. Then I added the
unhandled device statement to the UML driver.
* src/conf/domain_conf.h: change _virDomainNetDef type from int to
virDomainNetType enum
* src/conf/domain_conf.c src/lxc/lxc_driver.c src/qemu/qemu_conf.c
src/uml/uml_conf.c: make sure all enum cases are properly handled
in switches
The current virDomainAttachDevice API can be (ab)used to change
the media of an existing CDROM/Floppy device. Going forward there
will be more devices that can be configured on the fly and overloading
virDomainAttachDevice for this is not too pleasant. This patch adds
a new virDomainUpdateDeviceFlags() explicitly just for modifying
existing devices.
* include/libvirt/libvirt.h.in: Add virDomainUpdateDeviceFlags
* src/driver.h: Internal API for virDomainUpdateDeviceFlags
* src/libvirt.c, src/libvirt_public.syms: Glue public API to
driver API
* src/esx/esx_driver.c, src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c, src/uml/uml_driver.c,
src/vbox/vbox_tmpl.c, src/xen/xen_driver.c, src/xenapi/xenapi_driver.c: Add
stubs for new driver entry point
The current API for domain events has a number of problems
- Only allows for domain lifecycle change events
- Does not allow the same callback to be registered multiple times
- Does not allow filtering of events to a specific domain
This introduces a new more general purpose domain events API
typedef enum {
VIR_DOMAIN_EVENT_ID_LIFECYCLE = 0, /* virConnectDomainEventCallback */
...more events later..
}
int virConnectDomainEventRegisterAny(virConnectPtr conn,
virDomainPtr dom, /* Optional, to filter */
int eventID,
virConnectDomainEventGenericCallback cb,
void *opaque,
virFreeCallback freecb);
int virConnectDomainEventDeregisterAny(virConnectPtr conn,
int callbackID);
Since different event types can received different data in the callback,
the API is defined with a generic callback. Specific events will each
have a custom signature for their callback. Thus when registering an
event it is neccessary to cast the callback to the generic signature
eg
int myDomainEventCallback(virConnectPtr conn,
virDomainPtr dom,
int event,
int detail,
void *opaque)
{
...
}
virConnectDomainEventRegisterAny(conn, NULL,
VIR_DOMAIN_EVENT_ID_LIFECYCLE,
VIR_DOMAIN_EVENT_CALLBACK(myDomainEventCallback)
NULL, NULL);
The VIR_DOMAIN_EVENT_CALLBACK() macro simply does a "bad" cast
to the generic signature
* include/libvirt/libvirt.h.in: Define new APIs for registering
domain events
* src/driver.h: Internal driver entry points for new events APIs
* src/libvirt.c: Wire up public API to driver API for events APIs
* src/libvirt_public.syms: Export new APIs
* src/esx/esx_driver.c, src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/phyp/phyp_driver.c,
src/qemu/qemu_driver.c, src/remote/remote_driver.c,
src/test/test_driver.c, src/uml/uml_driver.c,
src/vbox/vbox_tmpl.c, src/xen/xen_driver.c,
src/xenapi/xenapi_driver.c: Stub out new API entries
This provides the internal glue for the driver API
* src/driver.h: Internal API contract
* src/libvirt.c, src/libvirt_public.syms: Connect public API
to driver API
* src/esx/esx_driver.c, src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/phyp/phyp_driver.c,
src/qemu/qemu_driver.c, src/remote/remote_driver.c,
src/test/test_driver.c src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c: Stub out entry points
The internal glue layer for the new pubic API
* src/driver.h: Define internal driver API contract
* src/libvirt.c, src/libvirt_public.syms: Wire up public
API to internal driver API
* src/esx/esx_driver.c, src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/phyp/phyp_driver.c,
src/qemu/qemu_driver.c, src/remote/remote_driver.c,
src/test/test_driver.c, src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c: Stub new entry point
* src/uml/uml_driver.c (umlMonitorCommand): This function would
sometimes return -1, yet fail to free the "reply" it had allocated.
Hence, no caller would know to free the corresponding argument.
When returning -1, be sure to free all allocated resources.
* src/lxc/lxc_container.c src/lxc/lxc_controller.c src/lxc/lxc_driver.c
src/network/bridge_driver.c src/qemu/qemu_driver.c
src/uml/uml_driver.c: virFileMakePath returns 0 for success, or the
value of errno on failure, so error checking should be to test
if non-zero, not if lower than 0
Set up the types for the domainMemoryStats function and insert it into the
virDriver structure definition. Because of static initializers, update
every driver and set the new field to NULL.
* include/libvirt/libvirt.h.in: new API
* src/driver.h src/*/*_driver.c src/vbox/vbox_tmpl.c: add the new
entry to the driver structure
* python/generator.py: fix compiler errors, the actual python binding is
implemented later
* src/driver.h: add an extra entry point in the structure
* src/esx/esx_driver.c src/lxc/lxc_driver.c src/opennebula/one_driver.c
src/openvz/openvz_driver.c src/phyp/phyp_driver.c src/qemu/qemu_driver.c
src/remote/remote_driver.c src/test/test_driver.c src/uml/uml_driver.c
src/vbox/vbox_tmpl.c src/xen/xen_driver.c: add NULL entry points for
all drivers
Replace free(virBufferContentAndReset()) with virBufferFreeAndReset().
Update documentation and replace all remaining calls to free() with
calls to VIR_FREE(). Also add missing calls to virBufferFreeAndReset()
and virReportOOMError() in OOM error cases.
There is currently no way to determine the libvirt version of a remote
libvirtd we are connected to. This is a useful piece of data to enable
feature detection.
Introduce a number of new APIs to expose some boolean properties
of objects, which cannot otherwise reliably determined, nor are
aspects of the XML configuration.
* virDomainIsActive: Checking virDomainGetID is not reliable
since it is not possible to distinguish between error condition
and inactive domain for ID of -1.
* virDomainIsPersistent: Check whether a persistent config exists
for the domain
* virNetworkIsActive: Check whether the network is active
* virNetworkIsPersistent: Check whether a persistent config exists
for the network
* virStoragePoolIsActive: Check whether the storage pool is active
* virStoragePoolIsPersistent: Check whether a persistent config exists
for the storage pool
* virInterfaceIsActive: Check whether the host interface is active
* virConnectIsSecure: whether the communication channel to the
hypervisor is secure
* virConnectIsEncrypted: whether any network based commnunication
channels are encrypted
NB, a channel can be secure, even if not encrypted, eg if it does
not involve the network, like a UNIX socket, or pipe.
* include/libvirt/libvirt.h.in: Define public API
* src/driver.h: Define internal driver API
* src/libvirt.c: Implement public API entry point
* src/libvirt_public.syms: Export API symbols
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/interface/netcf_driver.c, src/network/bridge_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c: Stub out driver tables
A character device's target (it's interface in the guest) had only a
single property: port. This patch is in preparation for adding targets
which require other properties.
Since this changes the conf type for character devices this affects
a number of drivers:
* src/conf/domain_conf.[ch] src/esx/esx_vmx.c src/qemu/qemu_conf.c
src/qemu/qemu_driver.c src/uml/uml_conf.c src/uml/uml_driver.c
src/vbox/vbox_tmpl.c src/xen/xend_internal.c src/xen/xm_internal.c:
target properties are moved into a union in virDomainChrDef, and a
targetType field is added to identify which union member should be
used. All current code which touches a virDomainChrDef is updated both
to use the new union field, and to populate targetType if necessary.
All drivers have copy + pasted inadequate error reporting which wraps
util.c:virGetHostname. Move all error reporting to this function, and improve
what we report.
Changes from v1:
Drop the driver wrappers around virGetHostname. This means we still need
to keep the new conn argument to virGetHostname, but I think it's worth
it.
The LXC driver was mistakenly returning -1 for lxcStartup()
in scenarios that are not an error. This caused the libvirtd
to quit for unprivileged users. This fixes the return code
of LXC driver, and also adds a "name" field to the virStateDriver
struct and logging to make it easier to find these problems
in the future
* src/driver.h: Add a 'name' field to state driver to allow
easy identification during failures
* src/libvirt.c: Log name of failed driver for virStateInit
failures
* src/lxc/lxc_driver.c: Don't return a failure code for
lxcStartup() if LXC is not available on this host, simply
disable the driver.
* src/network/bridge_driver.c, src/node_device/node_device_devkit.c,
src/node_device/node_device_hal.c, src/opennebula/one_driver.c,
src/qemu/qemu_driver.c, src/remote/remote_driver.c,
src/secret/secret_driver.c, src/storage/storage_driver.c,
src/uml/uml_driver.c, src/xen/xen_driver.c: Fill in name
field in virStateDriver struct
Rename virDomainIsActive to virDomainObjIsActive, and
virInterfaceIsActive to virInterfaceObjIsActive and finally
virNetworkIsActive to virNetworkObjIsActive.
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/conf/interface_conf.h, src/conf/network_conf.c,
src/conf/network_conf.h, src/lxc/lxc_driver.c,
src/network/bridge_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/qemu/qemu_driver.c,
src/test/test_driver.c, src/uml/uml_driver.c: Update for
renamed APIs.
The virDomainObjPtr object stores state about a running domain.
This object is shared across all drivers so it is not appropriate
to include driver specific state here. This patch adds the ability
to request a blob of private data per domain object instance. The
driver must provide a allocator & deallocator for this purpose
THis patch abuses the virCapabilitiesPtr structure for storing the
allocator/deallocator callbacks, since it is already being abused
for other internal things relating to parsing. This should be moved
out into a separate object at some point.
* src/conf/capabilities.h: Add privateDataAllocFunc and
privateDataFreeFunc fields
* src/conf/domain_conf.c: Invoke the driver allocators / deallocators
when creating/freeing virDomainObjPtr instances.
* src/conf/domain_conf.h: Pass virCapsPtr into virDomainAssignDef
to allow access to the driver specific allocator function
* src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/qemu/qemu_driver.c,
src/test/test_driver.c, src/uml/uml_driver.c: Update for
change in virDomainAssignDef contract
The current virDomainObjListPtr object stores domain objects in
an array. This means that to find a particular objects requires
O(n) time, and more critically acquiring O(n) mutex locks.
The new impl replaces the array with a virHashTable, keyed off
UUID. Finding a object based on UUID is now O(1) time, and only
requires a single mutex lock. Finding by name/id is unchanged
in complexity.
In changing this, all code which iterates over the array had
to be updated to use a hash table iterator function callback.
Several of the functions which were identically duplicating
across all drivers were pulled into domain_conf.c
* src/conf/domain_conf.h, src/conf/domain_conf.c: Change
virDomainObjListPtr to use virHashTable. Add a initializer
method virDomainObjListInit, and rename virDomainObjListFree
to virDomainObjListDeinit, since its not actually freeing
the container, only its contents. Also add some convenient
methods virDomainObjListGetInactiveNames,
virDomainObjListGetActiveIDs and virDomainObjListNumOfDomains
which can be used to implement the correspondingly named
public API entry points in drivers
* src/libvirt_private.syms: Export new methods from domain_conf.h
* src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_conf.c, src/openvz/openvz_driver.c,
src/qemu/qemu_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c: Update all code
to deal with hash tables instead of arrays for domains
Implementation of tunnelled migration, using a Unix Domain Socket
on the qemu backend. Note that this requires very new versions of
qemu (0.10.7 at least) in order to get the appropriate bugfixes.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Add the virStrncpy function, which takes a dst string, source string,
the number of bytes to copy and the number of bytes available in the
dest string. If the source string is too large to fit into the
destination string, including the \0 byte, then no data is copied and
the function returns NULL. Otherwise, this function copies n bytes
from source into dst, including the \0, and returns a pointer to the
dst string. This function is intended to replace all unsafe uses
of strncpy in the code base, since strncpy does *not* guarantee that
the buffer terminates with a \0.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
