When trying to set numatune mode directly using virsh numatune command,
correct error is raised, however numatune structure was not deallocated,
thus resulting in creating an empty numatune element in the guest XML,
if none was present before. Running the same command aftewards results
in a successful change with broken XML structure. Patch fixes the
deallocation problem as well as checking for invalid attribute
combination VIR_DOMAIN_NUMATUNE_PLACEMENT_AUTO + a nonempty nodeset.
Resolves https://bugzilla.redhat.com/show_bug.cgi?id=1129998
The 'min_guarantee' is used by VMware ESX and OpenVZ drivers,
with qemu however, libvirt should report error when starting a domain,
because this element is not used.
Resolves https://bugzilla.redhat.com/show_bug.cgi?id=1122455
On some places in the libvirt code we have:
f(a,z)
instead of
f(a, z)
This trivial patch fixes couple of such occurrences.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Libvirt measures vram in Kbytes, not in bytes, so calculation
of Mbytes was incorrect. PCS server can take vram argument
with units, so I added K postfix to make params a little bit clearer.
That sets a new flag, but that flag does mean the child will get
LISTEN_FDS and LISTEN_PID environment variables properly set and
passed FDs reordered so that it corresponds with LISTEN_FDS (they must
start right after STDERR_FILENO).
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Even line like this:
int asdf = i - somevar;
was matched by the regex, so this patch adds '=' to the list of
characters that break the regexp.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
It's just a wrapper around NewFD and NewUNIX that selects the right
option and increments the number of used FDs.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Since not only systemd can do this (we'll be doing it as well few
patches later), change 'systemd' to 'caller' and fix LISTEN_FDS to
LISTEN_PID where applicable.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
When formatting the forward mode addresses or interfaces the switch was
done based on the type of the network rather than of the type of the
individual <interface>/<address> element. In case a user would specify
an incorrect network type ("passhtrough") with <address> elements,
libvirtd would crash as it would attempt to format an <interface>.
Use the type of the individual element to format the XML.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1132347
https://bugzilla.redhat.com/show_bug.cgi?id=1078126
Using 'virsh attach-device --config' (or --persistent) to attach a
file backed lun device will succeed; however, subsequent domain restarts
will result in failure because the configuration of a file backed lun
is not supported.
Although allowing 'illegal configurations' is something that can be
allowed, it may not be practical in this case. Generally, when attaching
a device to a domain means the domain must be running. A way around
this is using the --config (or --persistent) option. When an attach
is done to a running domain, a temporary configuration is modified
first followed by the live update. The live update will make a number
of disk validity checks when building the qemu command to attach the
disk. If any fail, then change is rejected.
Rather than allow a potentially illegal combination, adjust the code
in the configuration path to make the same checks as the running path
will make with respect to disk validity checks. This way we avoid
having the potential for some subsequent start/reboot to fail because
an illegal combination was allowed.
NB: The live path still checks the configuration since it is possible
to just do --live guest modification...
Since vbox driver rewrite the virDriver structure init moved from
vbox_tmpl.c into vbox_common.c. However, our hvsupport.pl script
doesn't count with that. It still parses vbox_tmp.c and looks for
virDriver structure which is not found there anymore. As a result,
at hvsupport page is seems like vbox driver doesn't support
anything.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In case the host has 2 or more NUMA nodes, we fetch CPU map for each
node. However, we need to free the CPU map in between loops:
==29513== 96 (72 direct, 24 indirect) bytes in 3 blocks are definitely lost in loss record 951 of 1,264
==29513== at 0x4C2A700: calloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==29513== by 0x52AD24B: virAlloc (viralloc.c:144)
==29513== by 0x52AF0E6: virBitmapNew (virbitmap.c:78)
==29513== by 0x52FB720: virNumaGetNodeCPUs (virnuma.c:294)
==29513== by 0x53C700B: nodeCapsInitNUMA (nodeinfo.c:1886)
==29513== by 0x11759708: vboxCapsInit (vbox_common.c:398)
==29513== by 0x11759CC4: vboxConnectOpen (vbox_common.c:514)
==29513== by 0x53C965F: do_open (libvirt.c:1147)
==29513== by 0x53C9EBC: virConnectOpen (libvirt.c:1317)
==29513== by 0x142905: remoteDispatchConnectOpen (remote.c:1215)
==29513== by 0x126ADF: remoteDispatchConnectOpenHelper (remote_dispatch.h:2346)
==29513== by 0x5453D21: virNetServerProgramDispatchCall (virnetserverprogram.c:437)
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The "maxMemory" element was never supported by libvirt. Remove it from
the test XMLs. (Found while actually trying to add support for a
identically named element).
https://bugzilla.redhat.com/show_bug.cgi?id=1103245
An advice appeared there on the qemu-devel list [1]. When a domain is
suspended and then resumed guest kernel is not aware of this. So we've
introduced virDomainSetTime API that resets the time within guest
using qemu-ga. On the other hand, qemu itself is trying to make RTC
beat faster to catch the difference. But if we don't tell qemu that
guest's time was reset via the other method, both mechanisms are
applied resulting in again wrong guest time. In order to avoid summing
both corrections we need to tell qemu that it should not use the RTC
injection if the guest time is set via guest agent.
1: http://www.mail-archive.com/qemu-devel@nongnu.org/msg236435.html
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When a user would try changing the persistent IO tuning settings for a
disk that was hotplugged to a vm in a transient way, the
qemuDomainSetBlockIoTune API would use the same index for both the
live and config disk array. The disk was missing from the config array
though causing a crash of libvirtd.
To fix the issue, determine the indexes separately.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1131819
https://bugzilla.redhat.com/show_bug.cgi?id=1095636
When starting up the domain the domain's NICs are allocated. As of
1f24f682 (v1.0.6) we are able to use multiqueue feature on virtio
NICs. It breaks network processing into multiple queues which can be
processed in parallel by different host CPUs. The queues are, however,
created by opening /dev/net/tun several times. Unfortunately, only the
first FD in the row is labelled so when turning the multiqueue feature
on in the guest, qemu will get AVC denial. Make sure we label all the
FDs needed.
Moreover, the default label of /dev/net/tun doesn't allow
attaching a queue:
type=AVC msg=audit(1399622478.790:893): avc: denied { attach_queue }
for pid=7585 comm="qemu-kvm"
scontext=system_u:system_r:svirt_t:s0:c638,c877
tcontext=system_u:system_r:virtd_t:s0-s0:c0.c1023
tclass=tun_socket
And as suggested by SELinux maintainers, the tun FD should be labeled
as svirt_t. Therefore, we don't need to adjust any range (as done
previously by Guannan in ae368ebf) rather set the seclabel of the
domain directly.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Removing a shared device needs special steps for disks and hostdevs.
Instead of having one function dealing this split the code into two
separate functions that can be used with better granularity.
Adding a shared device needs special steps for disks and hostdevs.
Instead of having one function dealing this split the code into two
separate functions that can be used with better granularity.
The qemuCheckSharedDevice function is operating only on disk devices.
Rename it and change the arguments to reflect that and refactor some
logic for more readability.
Split it out into a separate function and simplify the code. There's no
need to copy the entry to update it as the hash returns pointer to the
existing item.
Also remove the now unused qemuSharedDeviceEntryCopy function.
To allow reuse split the code into a separate function and refactor it.
To update an existing entry there's no need to copy it first, just
update it inplace.
Pass the source of the changed media instead of a complete disk
definition.
Note that the @disk argument now contains what @olddisk would contain.
The new source is passed as a virStorageSource struct.
When we are changing media (or doing other hotplug operations) we need
to setup cgroups, locking and seclabels on the new disk. This is a
multi-step process where every piece can fail. To simplify dealing with
this introduce qemuDomainPrepareDisk that similarly to
qemuDomainPrepareDiskChainElement initializes/tears down a whole new
disk to be used with the domain.
Additionally the function supports passing a different source struct for
media changes of cdroms that will be refactored later.