In these functions I'm fixing here, we do call
qemuMonitorJSONCheckError() followed by another check if qemu
reply contains 'return' object. If it wouldn't, the former
CheckError() function would error out and the flow would not even
get to the latter.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Usually, the flow in this area of the code is as follows:
qemuMonitorJSONMakeCommand()
qemuMonitorJSONCommand()
qemuMonitorJSONCheckError()
parseReply()
But in this function, for some reasons, the last two steps were
swapped. This makes no sense.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In qemuDomainDefAddDefaultDevices we check for a non-NULL
def->os.machine for x86 archs, but not the others.
Moreover, the only caller - qemuDomainDefPostParse
already checks for it and even then it can happen only
if /etc/libvirt contains an XML without a machine type.
We do not need to propagate the exact return values
and the only possible ones are 0 and -1 anyway.
Remove the temporary variable and use the usual pattern:
if (f() < 0)
return -1;
https://bugzilla.redhat.com/show_bug.cgi?id=1139766
Thing is, for some reasons you can have your domain's RTC to be
in something different than UTC. More weirdly, it's not only time
zone what you can shift it of, but an arbitrary value. So, if
domain is configured that way, libvirt will correctly put it onto
qemu cmd line and moreover track it as this offset changes during
domain's life time (e.g. because guest OS decides the best thing
to do is set new time to RTC). Anyway, they way in which this
tracking is implemented is events. But we've got a problem if
change in guest's RTC occurs and the daemon is not running. The
event is lost and we end up reporting invalid value in domain
XML. Therefore, when the daemon is starting up again and it is
reconnecting to all running domains, re-fetch their RTC so the
correct offset value can be computed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
If a panic device is being defined without a model in a domain
the default value is always overwritten with model ISA. An ISA
bus does not exist on S390 and therefore specifying a panic device
results in an unsupported configuration.
Since the S390 architecture inherently provides a crash detection
capability the panic device should be defined in the domain xml.
This patch adds an s390 panic device model and prevents setting a
device address on it.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The default USB controller is not sent to destination as the older versions
of libvirt(0.9.4 or earlier as I see in commit log of 409b5f54) didn't
support them. For some archs where the support started much later can
safely send the USB controllers without this worry. So, send the controller
to destination for all archs except x86. Moreover this is not very applicable
to x86 as the USB controller has model ich9_ehci1 on q35 and for pc-i440fx,
there cant be any slots before USB as it is fixed on slot 1.
The patch fixes a bug that, if the USB controller happens to occupy
a slot after disks/interfaces and one of them is hot-unplugged, then
the default USB controller added on destination takes the smallest slot
number and that would lead to savestate mismatch and migration
failure. Seen and verified on PPC64.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
We had both and the only difference was that the latter also included
information about multifunction setting. The problem with that was that
we couldn't use functions made for only one of the structs (e.g.
parsing). To consolidate those two structs, use the one in virpci.h,
include that in domain_conf.h and add the multifunction member in it.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Rather than take username and password as parameters, now take
a qemuDomainSecretInfoPtr and decode within the function.
NB: Having secinfo implies having the username for a plain type
from a successful virSecretGetSecretString
Signed-off-by: John Ferlan <jferlan@redhat.com>
Similar to the qemuDomainSecretDiskPrepare, generate the secret
for the Hostdev's prior to call qemuProcessLaunch which calls
qemuBuildCommandLine. Additionally, since the secret is not longer
added as part of building the command, the hotplug code will need
to make the call to add the secret in the hostdevPriv.
Since this then is the last requirement to pass a virConnectPtr
to qemuBuildCommandLine, we now can remove that as part of these
changes. That removal has cascading effects through various callers.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Modeled after the qemuDomainDiskPrivatePtr logic, create a privateData
pointer in the _virDomainHostdevDef to allow storage of private data
for a hypervisor in order to at least temporarily store auth/secrets
data for usage during qemuBuildCommandLine.
NB: Since the qemu_parse_command (qemuParseCommandLine) code is not
expecting to restore the auth/secret data, there's no need to add
code to handle this new structure there.
Updated copyrights for modules touched. Some didn't have updates in a
couple years even though changes have been made.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Rather than needing to pass the conn parameter to various command
line building API's, add qemuDomainSecretPrepare just prior to the
qemuProcessLaunch which calls qemuBuilCommandLine. The function
must be called after qemuProcessPrepareHost since it's expected
to eventually need the domain masterKey generated during the prepare
host call. Additionally, future patches may require device aliases
(assigned during the prepare domain call) in order to associate
the secret objects.
The qemuDomainSecretDestroy is called after the qemuProcessLaunch
finishes in order to clear and free memory used by the secrets
that were recently prepared, so they are not kept around in memory
too long.
Placing the setup here is beneficial for future patches which will
need the domain masterKey in order to generate an encrypted secret
along with an initialization vector to be saved and passed (since
the masterKey shouldn't be passed around).
Finally, since the secret is not added during command line build,
the hotplug code will need to get the secret into the private disk data.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Introduce a new private structure to hold qemu domain auth/secret data.
This will be stored in the qemuDomainDiskPrivate as a means to store the
auth and fetched secret data rather than generating during building of
the command line.
The initial changes will handle the current username and secret values
for rbd and iscsi disks (in their various forms). The rbd secret is
stored as a base64 encoded value, while the iscsi secret is stored as
a plain text value. Future changes will store encoded/encrypted secret
data as well as an initialization vector needed to be given to qemu
in order to decrypt the encoded password along with the domain masterKey.
The inital assumption will be that VIR_DOMAIN_SECRET_INFO_PLAIN is
being used.
Although it's expected that the cleanup of the secret data will be
done immediately after command line generation, reintroduce the object
dispose function qemuDomainDiskPrivateDispose to handle removing
memory associated with the structure for "normal" cleanup paths.
Signed-off-by: John Ferlan <jferlan@redhat.com>
After killing one of the conditionals it's now guaranteed to have
@drivealias populated when calling the monitor, so the code attempting
to cleanup can be simplified.
For strange reasons if a perf event type was not supported or failed to
be enabled at VM start libvirt would ignore the failure.
On the other hand on restart if the event could not be re-enabled
libvirt would fail to reconnect to the VM and kill it.
Both don't make really sense. Fix it by failing to start the VM if the
event is not supported and change the event to disabled if it can't be
reconnected (unlikely).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1329045
Both disk->src->shared and disk->src->readonly can't be modified when
changing disk source for floppy and cdrom drives since both arguments
are passed as arguments of the disk rather than the image in qemu.
Historically these fields have only two possible values since they are
represented as XML thus we need to ignore if user did not provide them
and thus we are treating them as false.
If qemu doesn't support DEVICE_TRAY_MOVED event the code that attempts
to change media would attempt to re-eject the tray even if it wouldn't
be notified when the tray opened. Add a capability bit and skip retrying
for old qemus.
Empty floppy drives start with tray in "open" state and libvirt did not
refresh it after startup. The code that inserts media into the tray then
waited until the tray was open before inserting the media and thus
floppies could not be inserted.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1326660
This reverts commit 6e244c659f, which
added support to qemu for the "peer" attribute in domain interface <ip>
elements.
It's being removed temporarily for the release of libvirt 1.3.4
because the feature doesn't work, and there are concerns that it may
need to be modified in an externally visible manner which could create
backward compatibility problems.
Conflicts:
tests/qemuxml2argvmock.c - a mock of virNetDevSetOnline() was added
which may be assumed by other tests added since the original commit,
so it isn't being reverted.
Similarly to what commit 7140807917 did with some internal paths,
clear vnc socket paths that were generated by us. Having such path in
the definition can cause trouble when restoring the domain. The path is
generated to the per-domain directory that contains the domain ID.
However, that ID will be different upon restoration, so qemu won't be
able to create that socket because the directory will not be prepared.
To be able to migrate to older libvirt, skip formatting the socket path
in migratable XML if it was autogenerated. And mark it as autogenerated
if it already exists and we're parsing live XML.
Best viewed with '-C'.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1326270
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
When the domain definition describes a machine with NUMA, setting the
maximum vCPU count via the API might lead to an invalid config.
Add a check that will forbid this until we add more advanced cpu config
capabilities.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1327499
Instead of setting the default qemu stdio logging approach in
virQEMUDriverConfigLoadFile set it in virQEMUDriverConfigNew so that
it's properly set even when the config is not present.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1325075
If the domain name is long enough, the timestamp can prolong the
filename for automatic coredump to more than the filesystem's limit.
Simply shorten it like we do in other places. The timestamp helps with
the unification, but having the ID in the name won't hurt.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1289363
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Add virDomainObjGetShortName() and use it. For now that's used in one
place, but we should expose it so that future patches can use it.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This function - in contrast with qemuBuildCommandLine - merely
constructs our internal command representation of a domain. This
is then later compared against expected output. Or, this function
is used also in virConnectDomainXMLToNative(). But due to a copy
paste error this function, just like its image - has @forceFips
argument that if enabled forces FIPS, otherwise mimics FIPS state
in the host. If FIPS is enabled or forced the generated command
line is different to state in which FIPS is disabled. Problem is,
while this could be desired in the virConnectDomainXMLToNative()
case, this is undesirable in the test suite as it will produce
unpredicted results.
Solution to this is to rename argument to @enableFips to
specifically tell whether we expect command line to be build in
either of fashions and make virConnectDomainXMLToNative()
implementation fetch FIPS state and pass it to
qemuProcessCreatePretendCmd().
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This error message was too specific, based on the incorrect assumption
that any error was cause by auto-added bridges:
failed to create PCI bridge on bus 2: too many devices
with fixed addresses
In practice you can't know if a bridge with an index <= the bus it's
connecting to was added automatically, or if it was a mistake in
explicit config, and the auto-add problem is going to be dealt with in
a different way in an upcoming patch. The new message is this:
PCI Controller at index 1 (0x01) has "
bus='0x02', but bus must be <= index
(note that index is given in both decimal and hex because it is
formatted as decimal in the XML, but bus is formatted as hex, and
displaying the hex value of index makes it easier to see the problem
when index > 9 (which will often be the case with PCIe, since most
controllers only have a single port, not 32 slots as with standard
PCI)).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1004593
The values are currently limited to LLONG_MAX which causes some
problems. QEMU conveniently changed their maximum to 1e15 (1 PB) which
is enough for some time and we need to adapt to that so that we don't
throw "Unknown error" messages. Strictly limiting these values actually
fixes some corner case values (off-by-one checks in QEMU probably).
Since values out of the new specified range do not overflow anything,
change the type of error as well.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1317531
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This an ubuntu/debian packaging convention. At one point it may have
been an actually different binary, but at least as of ubuntu precise
(the oldest supported ubuntu distro, released april 2012) kvm-img is
just a symlink to qemu-img for back compat.
I think it's safe to drop support for it
QEMU introduced the query-gic-capabilities QMP command
with commit 4468d4e0f383: use the command, if available,
to probe available GIC capabilities.
The information obtained is stored in a virQEMUCaps
instance, and will be later used to fill in a
virDomainCaps instance.
The struct contains a single boolean field, 'supported':
the meaning of this field is too generic to be limited to
devices only, and in fact it's already being used for
other things like loaders and OSs.
Instead of trying to come up with a more generic name just
get rid of the struct altogether.
The common idiom in the driver API implementations is roughly:
- ACL check
- BeginJob (if needed)
- AgentAvailable (if needed)
- !IsActive
A few calls had an extra !IsActive before BeginJob, which doesn't
seem to serve much use. Drop them
Migration API allows to specify a destination domain configuration.
Offline domain has only inactive XML and it is replaced by configuration
specified using VIR_MIGRATE_PARAM_DEST_XML param. In case of live
migration VIR_MIGRATE_PARAM_DEST_XML param is applied for active XML.
This commit introduces the new VIR_MIGRATE_PARAM_PERSIST_XML param
that can be used within live migration to replace persistent/inactive
configuration.
Required for: https://bugzilla.redhat.com/show_bug.cgi?id=835300
Commit id '4b75237f' seems to have triggered Coverity into finding
at least one memory leak in xen_xl.c for error path for cleanup where
the listenAddr would be leaked. Reviewing other callers, it seems that
qemu_parse_command.c would have the same issue, so just it too.
When creating the master key, we used mode 0600 (which we should) but
because we were creating it as root, the file is not readable by any
qemu running as non-root. Fortunately, it's just a matter of labelling
the file. We are generating the file path few times already, so let's
label it in the same function that has access to the path already.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
In a few places in libvirt we busy-wait for events, for example qemu
creating a monitor socket. This is problematic because:
- We need to choose a sufficiently small polling period so that
libvirt doesn't add unnecessary delays.
- We need to choose a sufficiently large polling period so that
the effect of busy-waiting doesn't affect the system.
The solution to this conflict is to use an exponential backoff.
This patch adds two functions to hide the details, and modifies a few
places where we currently busy-wait.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Rather than trying some magic calculations on our side query the monitor
for the current size of the memory balloon both on hotplug and
hotunplug.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1220702
Now that there is just one format of the memory balloon command line
used the code can be merged into a single function.
Additionally with some tweaks to the control flow the code is easier to
read.
The change that made qemu not add the memballoon by default happened
prior to 0.12.0. Additionaly the comment was misleading due to the code
that was added below. Since we always need to add a balloon on the
commandline drop the comment.
The only caller of this code is:
for (i = 0; i < dom->def->ngraphics; i++) {
if (dom->def->graphics[i]->type == VIR_DOMAIN_GRAPHICS_TYPE_SPICE) {
if (!(mig->graphics =
qemuMigrationCookieGraphicsAlloc(driver, dom->def->graphics[i])))
return -1;
mig->flags |= QEMU_MIGRATION_COOKIE_GRAPHICS;
break;
}
}
So this is never triggered for VNC, and in fact VNC has no support for
seamless migration anyways so that seems correct. Drop the dead VNC
handling.
This is backed by the qemu device pxb-pcie, which will be available in
qemu 2.6.0.
As with pci-expander-bus (which uses qemu's pxb device), the busNr
attribute and <node> subelement of <target> are used to set the bus_nr
and numa_node options.
During post-parse we validate that the domain's machinetype is
q35-based (since the device shows up for 440fx-based machinetypes, but
is unusable), as well as checking that <node> specifies a node that is
actually configured on the guest.
This controller provides a single PCIe port on a new root. It is
similar to pci-expander-bus, intended to provide a bus that can be
associated with a guest-identifiable NUMA node, but is for
machinetypes with PCIe rather than PCI (e.g. q35-based machinetypes).
Aside from PCIe vs. PCI, the other main difference is that a
pci-expander-bus has a companion pci-bridge that is automatically
attached along with it, but pcie-expander-bus has only a single port,
and that port will only connect to a pcie-root-port, or to a
pcie-switch-upstream-port. In order for the bus to be of any use in
the guest, it must have either a pcie-root-port or a
pcie-switch-upstream-port attached (and one or more
pcie-switch-downstream-ports attached to the
pcie-switch-upstream-port).
The pxb device is a PCIe expander bus that can be added to any
Q35-based machinetype. A single PCIe port (*not* hotpluggable) is
provided; if more than one device is desired, or if hotplug
support is needed, either a pcie-root-port, or some combination of
pcie-switch-upstream-port and pcie-swith-downstream-ports must be
added to it. It can have a NUMA node number associated with it, as
well as a bus number.
This is backed by the qemu device "pxb".
The pxb device always includes a pci-bridge that is at the bus number
of the pxb + 1.
busNr and <node> from the <target> subelement are used to set the
bus_nr and numa_node options for pxb.
During post-parse we validate that the domain's machinetype is
440fx-based (since the pxb device only works on 440fx-based machines),
and <node> also gets a sanity check to assure that the NUMA node
specified for the pxb (if any - it's optional) actually exists on the
guest.
This is a standard PCI root bus (not a bridge) that can be added to a
440fx-based domain. Although it uses a PCI slot, this is *not* how it
is connected into the PCI bus hierarchy, but is only used for
control. Each pci-expander-bus provides 32 slots (0-31) that can
accept hotplug of standard PCI devices.
The usefulness of pci-expander-bus relative to a pci-bridge is that
the NUMA node of the bus can be specified with the <node> subelement
of <target>. This gives guest-side visibility to the NUMA node of
attached devices (presuming that management apps only assign a device
to a bus that has a NUMA node number matching the node number of the
device on the host).
Each pci-expander-bus also has a "busNr" attribute. The expander-bus
itself will take the busNr specified, and all buses that are connected
to this bus (including the pci-bridge that is automatically added to
any expander bus of model "pxb" (see the next commit)) will use
busNr+1, busNr+2, etc, and the pci-root (or the expander-bus with next
lower busNr) will use bus numbers lower than busNr.
The pxb device is a PCI expander bus that can be added to any
440fx-based machinetype. The PCI bus that is created has 32 standard
PCI slots (hotpluggable). It can have a NUMA node number associated
with it, as well as a bus number.
There are two places in qemu_domain_address.c where we have a switch
statement to convert PCI controller models
(VIR_DOMAIN_CONTROLLER_MODEL_PCI*) into the connection type flag that
is matched when looking for an upstream connection for that model of
controller (VIR_PCI_CONNECT_TYPE_*). This patch makes a utility
function in conf/domain_addr.c to do that, so that when a new PCI
controller is added, we only need to add the new model-->connect-type
in a single place.
The flags used to determine which devices could be plugged into which
controllers were quite confusing, as they tried to create classes of
connections, then put particular devices into possibly multiple
classes, while sometimes setting multiple flags for the controllers
themselves. The attempt to have a single flag indicate, e.g. that a
root-port or a switch-downstream-port could connect was not only
confusing, it was leading to a situation where it would be impossible
to specify exactly the right combinations for a new controller.
The solution is for the VIR_PCI_CONNECT_TYPE_* flags to have a 1:1
correspondence with each type of PCI controller, plus a flag for a PCI
endpoint device and another for a PCIe endpoint device (the only
exception to this is that pci-bridge and pcie-expander-bus controllers
have their upstream connection classified as
VIR_PCI_CONNECT_TYPE_PCI_DEVICE since they can be plugged into
*exactly* the same ports as any endpoint device). Each device then
has a single flag for connect type (plus the HOTPLUG flag if that
device can e hotplugged), and each controller sets the CONNECT bits
for all controllers that can be plugged into it, as well as for either
type of endpoint device that can be plugged in (and the HOTPLUG flag
if it can accept hotplugged devices).
With this change, it is *slightly* easier to understand the matching
of connections (as long as you remember that the flag for a
device/upstream-facing connection of a controller is the same as that
device's type, while the flags for a controller's downstream
connections is the OR of all device types that can be plugged into
that controller). More importantly, it will be possible to correctly
specify what can be plugged into a pcie-switch-expander-bus, when
support for it is added.
The watchdog cli refactoring in 4666b762 dropped the temporary variable
we use to convert to action=dump to action=pause for the qemu cli, and
stored the converted value in the domain structure. Our other watchdog
handling code then treated it as though the user requested action=pause,
which broke action=dump handling.
Revive the temporary variable to fix things.
I tried compiling libvirt with older gcc and probably because I used
different configure options I got some shadowed declarations.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
GCC in RHEL-6 complains about listen:
../../src/conf/domain_conf.c:23718: error: declaration of 'listen' shadows a global declaration [-Wshadow]
/usr/include/sys/socket.h:204: error: shadowed declaration is here [-Wshadow]
This renames all the listen to gListen.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
