AFAIK there aren't any cases where we will/should hit the old code
path for our supported qemu versions, so drop the old code.
Massive test suite churn follows
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
After 9c17d665fd the tap device for ethernet network type is
automatically precreated before spawning qemu. Problem is, the
qemuxml2argvtest wasn't updated and thus is failing. Because of
all the APIs that new code is calling, I had to mock a lot. Also,
since the tap FDs are labeled separately from the rest of the
devices/files I had to enable NOP security driver for the test
too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.1 the -drive argument can be used to configure
all disks, so the QEMU driver can assume it is always available
and drop support for -hda/-cdrom/etc.
Many of the tests need updating because a great many were
running without CAPS_DRIVE set, so using the -hda legacy
syntax.
Fixing the tests uncovered a bug in the argv -> xml
convertor which failed to handle disk with if=floppy.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
This patch implements the devices post parse callback and uses it to fill
the default qemu network card model into the XML if none is specified.
Libvirt assumes that the network card model for qemu is the "rtl8139".
Record this in the XML using the new callback to avoid user
confusion.
This patch teaches testutil how to read multi-line input files with
backspace-newline line continuation markers.
The patch also breaks up all the single-line arguments test input files into
multi-line files with lines shorter than 80 characters.
The current way of assigning names to the host network backend and
NIC device in QEMU was over complicated, by varying naming scheme
based on the NIC model and backend type. This simplifies the naming
to simply be 'net0' and 'hostnet0', allowing code to easily determine
the host network name and vlan based off the primary device alias
name 'net0'. This in turn allows removal of alot of QEMU specific
code from the XML parser, and makes it easier to assign new unique
names for NICs that are hotplugged
* src/conf/domain_conf.c, src/conf/domain_conf.h: Remove hostnet_name
and vlan fields from virNetworkDefPtr
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c:
Use a single network alias naming scheme regardless of NIC type
or backend type. Determine VLANs from the alias name.
* tests/qemuxml2argvdata/qemuxml2argv-net-eth-names.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args: Update
for new simpler naming scheme
We need these so that we can remove the devices via the monitor.
* src/domain_conf.h: add nic_name and hostnet_name to virDomainNetDef
* src/domain_conf.c: free nic_name and hostnet_name
* src/qemu_conf.c: add qemuAssignNetNames(), use it if qemu has
support for the param and pass the names on the command line
* tests/qemuxml2argv*: add a test for this
