An upcoming patch has a use for a tap device to be created that
doesn't need to be actually put into the "up" state, and keeping it
"down" keeps the output of ifconfig from being unnecessarily cluttered
(ifconfig won't show down interfaces unless you add "-a").
bridge.[ch]: add "up" as an arg to brAddTap()
uml_conf.c, qemu_command.c: add "up" (set to "true") to brAddTap() call.
Previously we used ioctl() to set the IP address and netmask of the
bridges used for virtual networks, and apparently the SIOCSIFNETMASK
ioctl implicitly set the broadcast address for the interface. The new
method of using the "ip" command requires broadcast address to be
explicitly specified though.
brSetInetAddress can only set a single IP address on the bridge, and
uses a method (ioctl(SIOCSETIFADDR)) that only works for IPv4. Replace
it and brSetInetNetmask with a single function that uses the external
"ip addr add" command to add an address/prefix to the interface - this
supports IPv6, and allows adding multiple addresses to the interface.
Although it isn't currently used in the code, we also add a
brDelInetAddress for completeness' sake.
Also, while we're modifying bridge.c, we change brSetForwardDelay and
brSetEnableSTP to use the new virCommand API rather than the
deprecated virRun, and also log an error message in bridge_driver.c if
either of those fail (previously the failure would be completely
silent).
Using automated replacement with sed and editing I have now replaced all
occurrences of close() with VIR_(FORCE_)CLOSE() except for one, of
course. Some replacements were straight forward, others I needed to pay
attention. I hope I payed attention in all the right places... Please
have a look. This should have at least solved one more double-close
error.
Instead of storing the IP address string in virNetwork related
structs, store the parsed virSocketAddr. This will make it
easier to add IPv6 support in the future, by letting driver
code directly check what address family is present
* src/conf/network_conf.c, src/conf/network_conf.h,
src/network/bridge_driver.c: Convert to use virSocketAddr
in virNetwork, instead of char *.
* src/util/bridge.c, src/util/bridge.h,
src/util/dnsmasq.c, src/util/dnsmasq.h,
src/util/iptables.c, src/util/iptables.h: Convert to
take a virSocketAddr instead of char * for any IP
address parameters
* src/util/network.h: Add macros to determine if an address
is set, and what address family is set.
The inet_pton and inet_ntop functions are obsolete, replaced
by getaddrinfo+getnameinfo with the AI_NUMERICHOST flag set.
These can be accessed via the virSocket APIs.
The bridge.c code had methods for fetching the IP address of
a bridge which used inet_ntop. Aside from the use of inet_ntop
these methods are broken, because a NIC can have multiple
addresses and this only returns one address. Since the methods
are never used, just remove them.
* src/conf/network_conf.c, src/nwfilter/nwfilter_learnipaddr.c:
Replace inet_pton and inet_ntop with virSocket APIs
* src/util/bridge.c, src/util/bridge.h: Remove unused methods
which called inet_ntop.
When passing a NULL tapfd argument to brAddTap, we need to close the fd
of the tap device. If we don't, libvirt will keep the fd open
indefinitely and renders the the guest unable to configure its side of
the tap device.
Signed-off-by: Soren Hansen <soren@linux2go.dk>
A Linux software bridge will assume the MAC address of the enslaved
interface with the numerically lowest MAC addr. When the bridge
changes MAC address there is a period of network blackout, so a
change should be avoided. The kernel gives TAP devices a completely
random MAC address. Occassionally the random TAP device MAC is lower
than that of the physical interface (eth0, eth1etc) that is enslaved,
causing the bridge to change its MAC.
This change sets an explicit MAC address for all TAP devices created
using the configured MAC from the XML, but with the high byte set
to 0xFE. This should ensure TAP device MACs are higher than any
physical interface MAC.
* src/qemu/qemu_conf.c, src/uml/uml_conf.c: Pass in a MAC addr
for the TAP device with high byte set to 0xFE
* src/util/bridge.c, src/util/bridge.h: Set a MAC when creating
the TAP device to override random MAC
Add the virStrncpy function, which takes a dst string, source string,
the number of bytes to copy and the number of bytes available in the
dest string. If the source string is too large to fit into the
destination string, including the \0 byte, then no data is copied and
the function returns NULL. Otherwise, this function copies n bytes
from source into dst, including the \0, and returns a pointer to the
dst string. This function is intended to replace all unsafe uses
of strncpy in the code base, since strncpy does *not* guarantee that
the buffer terminates with a \0.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
