libvirt/docs/kbase/debuglogs.rst

Debug Logs

Turning on debug logs

If you report a bug against libvirt, in most cases you will be asked to attach debug logs. These are bare text files which tracks transition between different states of libvirtd, what it has tried to achieve, etc. Because of client -- server schema used in libvirt, the logs can be either client or server too. Usually, it's server side that matters as nearly all interesting work takes place there. Moreover, libvirt catches stderr of all running domains. These can be useful as well.

Logging settings in libvirt

Log levels

Libvirt log messages are classified into 4 priority levels; the higher the priority level, the less is the volume of produced messages.

The log level setting is controlled by the log_filters and log_outputs settings explained in the Log outputs and Log filters sections respectively.

• 1: DEBUG
• 2: INFO
• 3: WARNING
• 4: ERROR

For debugging it's necessary to capture the DEBUG level entries as the name implies.

Log outputs

Log outputs describe where the log messages are being recorded. The outputs are described by a space-separated list of tuples in the following format:

level:output

level refers to the minimum priority level of entries recorded in the output.

output is one of the following:

file:FILENAME

Logging messages are appended to FILENAME.

journald

Logging goes to the journald logging daemon.

stderr

Logging goes to the standard error output stream of the libvirt daemon.

syslog:name

Logging goes to syslogd. name is used to identify the entries.

The default output on systems running journald is 3:journald. Note that journald can throttle the amount of logs per process so in order to capture debug logs of a libvirt daemon should go to a file instead (in addition to theoriginal logging daemon), e.g.:

"1:file:/var/log/libvirt/libvirtd.log 3:journald"

Log filters

Log filters, as the name suggest, help filtering out messages which are irrelevant to the cause. The log filters is a space-separated list of tuples list of tuples using the level:identifier format. Each filter defined this way will then limit messages coming from a module matching the identifier pattern (accepts globs too) to the given level."

As identifier is based on internal naming of modules, preferred way of configuring your filters is to start with the Example filter settings.

The rule of thumb here is to have more logs rather than less and miss something important.

Libvirt daemons logging configuration

Persistent setting

The daemon configuration files location is dependent on connection URI. For qemu:///system:

• open /etc/libvirt/libvirtd.conf in your favourite editor
• find & replace, or set these variables:

log_filters="3:remote 4:event 3:util.json 3:rpc 1:*"
log_outputs="1:file:/var/log/libvirt/libvirtd.log"

• save and exit
• restart libvirtd service

systemctl restart libvirtd.service

Note: Libvirt prior to the libvirt-4.4.0 release didn't support globbing patterns and thus requires more configuration. See Legacy (pre-4.4.0) libvirt daemon logging configuration.

However, when you are using the session mode qemu:///session or you run the libvirtd as unprivileged user you will find configuration file under $XDG_CONFIG_HOME/libvirt/libvirtd.conf.

Runtime setting

Debugging anomalies can be very painful, especially when trying to reproduce it after the daemon restarts, since the new session can make the anomaly "disappear". Therefore, it's possible to enable the debug logs during runtime using libvirt administration API. To use it conveniently, there's the virt-admin client provided by the libvirt-admin package. Use the package manager provided by your distribution to install this package. Once you have it installed, run the following as root to see the set of log filters currently being active:

# virt-admin daemon-log-filters
 Logging filters: 3:remote 4:util.json 4:rpc

In order to change this set, run the same command as root, this time with your own set of filters:

# virt-admin daemon-log-filters "3:remote 4:util.json 4:rpc 1:*"

Analogically, the same procedure can be performed with log outputs:

# virt-admin daemon-log-outputs
 Logging outputs: 3:syslog:libvirtd
# virt-admin daemon-log-outputs "1:file:/var/log/libvirt/libvirtd.log"

NOTE: It's always good practice to return the settings to the original state once you're finished debugging, just remember to save the original sets of filters and outputs and restore them at the end the same way as described above.

Removing filters and outputs

It's also possible to remove all the filters and produce an enormous log file, but it is not recommended since some of libvirt's modules can produce a large amount of noise. However, should you really want to do this, you can specify an empty set of filters:

# virt-admin daemon-log-filters ""
 Logging filters:

The situation is a bit different with outputs, since libvirt always has to log somewhere and resetting the outputs to an empty set will restore the default setting which depends on the host configuration, journald in our case:

# virt-admin daemon-log-outputs
 Logging outputs: 1:file:/var/log/libvirt/libvirtd.log
# virt-admin daemon-log-outputs ""
 Logging outputs: 2:journald

Legacy (pre-4.4.0) libvirt daemon logging configuration

Old libvirt versions didn't support globbing (e.g. 1:*) to configure logging, thus it's required to explicitly set logging level to 1 (debug level) with the log_level setting and then filter out the noise with a tailored log log_filters string.

# LEGACY SETTINGS PRIOR LIBVIRT 4.4.0
log_level = 1
log_filters="1:qemu 3:remote 4:event 3:util.json 3:rpc"
log_outputs="1:file:/var/log/libvirt/libvirtd.log"

Or using virt-admin:

## LEGACY APPROACH ENUMERATING ALL THE DESIRED MODULES ##
# virt-admin daemon-log-filters "1:util 1:libvirt 1:storage 1:network 1:nodedev 1:qemu"

Client library logging

By default the client library doesn't produce any logs and usually usually it's not very interesting on its own anyway.

In case you want to get the client logs, logging is controlled via the LIBVIRT_LOG_OUTPUTS and LIBVIRT_LOG_FILTERS environment variables. Generally when client logs are needed make sure you don't filter them:

export LIBVIRT_LOG_OUTPUTS="1:file:/tmp/libvirt_client.log"

What to attach?

Now you should go and reproduce the bug. Once you're finished, attach:

• /var/log/libvirt/libvirtd.log or whatever path you set for the daemon logs.
• If the problem is related to a domain named $dom attach:
  • /var/log/libvirt/qemu/$dom.log (Or substitute qemu with whatever hypervisor you are using.)
  • The XML configuration of the vm/domain obtained by virsh dumpxml $dom
• If the problem involves a crash of libvirtd or any other component, also attach the backtrace from the core dump if possible (e.g. using coredumpctl).
• If you are asked for client logs, /tmp/libvirt_client.log.
• Ideally don't tear down the environment in case additional information is required.

Example filter settings

Some filter setting suggestions for debugging more specific things. Unless it's explicitly stated, these work on libvirt 4.4.0 and later. Please note that some of the filters below may not log enough information for filing a proper libvirt bug. Usually it's better to log more than less.

Targeted logging for debugging QEMU VMs

Specifying only some sections allows for a targeted filter configuration which works on all versions and is sufficient for most cases.

1:libvirt 1:qemu 1:conf 1:security 3:event 3:json 3:file 3:object 1:util

Less verbose logging for QEMU VMs

Some subsystems are very noisy and usually not the culprit of the problems. They can be silenced individually for a less verbose log while still logging everything else. Usual suspects are the JSON code, RPC, authentication and such. A permissive filter is good for development use cases.

3:remote 4:event 3:util.json 3:util.object 3:util.dbus 3:util.netlink 3:node_device 3:rpc 3:access 1:*

Minimalistic QEMU QMP monitor logging

This filter logs only QMP traffic and skips most of libvirt's messages.

2:qemu.qemu_monitor 3:*