Update the configuration after a resize to ensure that after a reboot
the added vCPUs are preserved.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This was causing issues when the kernel was trying to reset the
interrupt and making the reboot fail.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The tty mode remains raw mode when cloud-hypervisor is terminted by
SIGTERM or SIGINT. The terminal is unusable due to echoing is
disabled which is really annoying.
Signed-off-by: Qiu Wenbo <qiuwenbo@phytium.com.cn>
Some physical address bits may become reserved in page table when SME
is enabled on AMD platform. Guest will trigger a reserved bit
violation page fault in this case due to write these reserved bits to 1
in page table. We need reduce the reserved bits to get the right
physical address range.
Signed-off-by: Qiu Wenbo <qiuwenbo@phytium.com.cn>
The KVM_SET_GSI_ROUTING ioctl is very simple, it overrides the previous
routes configuration with the new ones being applied. This means the
caller, in this case cloud-hypervisor, needs to maintain the list of all
interrupts which needs to be active at all times. This allows to
correctly support multiple devices to be passed through the VM and being
functional at the same time.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Call the "CTFY" method that will itself call Notify() on the CPU objects
in the ACPI namespace.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add ability to notify via the GED device that there is some new hotplug
activity. This will be used by the CpuManager (and later DeviceManager
itself) to notify of new hotplug activity.
Currently it has a hardcoded IRQ of 5 as the ACPI tables also need to
refer to this IRQ and the IRQ allocation does not permit the allocation
of specific IRQs.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Currently only increasing the number of vCPUs is supported but in the
future it will be extended.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When configuring a processor after boot as a hotplug CPU we only
configure a subset of the CPU state. In particular we should not
configure the FPU, segment registers (or reconfigure the paging which is
a side-effect of that) nor the main registers. Achieve this by making
the function take an Option type for the start address.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Refactor the vCPU thread starting so that there is the possibility to
bring on extra vCPU threads.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Currently this just holds the thread handle but will be enlarged to
encompass details such as whether the vCPU is currently being inserted
or ejected.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The MADT table contains the details of all the potential vCPUs and
whether they are present at boot (as indicated by the flags field.)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When initialising the ACPI tables and configuring the VM use the new
accessor on the CpuManager to get the number of boot vCPUs.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Since the kvm crates now depend on vmm-sys-util, the bump must be
atomic.
The kvm-bindings and ioctls 0.2.0 and 0.4.0 crates come with a few API
changes, one of them being the use of a kvm_ioctls specific error type.
Porting our code to that type makes for a fairly large diff stat.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
context ID on vsock man defines a 32-bits value, openapi default integer
is a signed 32-bits value.
This could lead to miss one bit during castings for typed client
implmentations. Lets increase the range of valid values by requesting an
int64.
Signed-off-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
In case the VM is started with the flag "--pmem mergeable=on", it means
the user expects the guest persistent memory pages to be marked as
mergeable. This commit relies on the madvise(MADV_MERGEABLE) system call
to inform the host kernel about these pages.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to let the user indicate if the persistent memory pages should
be marked as mergeable or not, a new option is being introduced.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In case the VM is started with the flag "--memory mergeable=on", it
means the user expects the guest RAM pages to be marked as mergeable.
This commit relies on the madvise(MADV_MERGEABLE) system call to inform
the host kernel about these pages.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to let the user indicate if the guest RAM pages should be
marked as mergeable or not, a new option is being introduced.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When vmm.ping give a response, we expect get the version from
the VMM not the vmm create
Signed-off-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
vmm.ping will help to check if http API server is up and
running.
This also removes the vmm.info endpoint.
Signed-off-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
The CPU manager uses an I/O port and to prevent potential clashes with
assignment for PCI devices ensure that it is allocated by the allocator.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rather than hardcode the CPU status for all the CPUs instead query from
the CPU manager via the I/O port that is is on via the ACPI tables.
Each CPU device has a _STA method that calls into the CSTA method which
reads and writes the I/O ports via the PRST field which exposes the I/O
port through and OpRegion.
As we only support boot CPUS report that all the CPUs are enabled for
now.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The Linux kernel expects all CPUs, whether they be enabled or disabled
to have an _MAT entry containing the LAPIC details for this CPU with the
enabled bit set to 1 (in the flags.)
In the MADT table the same bit is used to determine if the CPU is
present at boot vs available later.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When adding devices to the guest, and populating the device model, we
should prefix the routines with add_. When we're just creating the
device objects but not yet adding them we use make_.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to reduce the DeviceManager's new() complexity, we can move the
MMIO devices creation code into its own routine.
Fixes: #441
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to reduce the DeviceManager's new() complexity, we can move the
PCI devices creation code into its own routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to reduce the DeviceManager's new() complexity, we can move the
ACPI device creation code into its own routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to reduce the DeviceManager's new() complexity, we can move the
ACPI device creation code into its own routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to reduce the DeviceManager's new() complexity, we can move the
legacy devices creation code into its own routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to reduce the DeviceManager's new() complexity, we can move the
console creation code into its own routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Move CpuManager, Vcpu and related functionality to its own module (and
file) inside the VMM crate
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In most cases we return a 204 (No Content) and not a 201.
In those cases, we do not send any HTTP body back at all.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The new micro_http package provides a built-in HttpServer wrapper for
running a more robust HTTP server based on the package HTTP API.
Switching to this implementation allows us to, among other things,
handle HTTP requests that are larger than 1024 bytes.
Fixes: #423
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The HTTP API responses are encoded in json
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Tested-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
Signed-off-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
Update micro_http create to allow set content type.
Suggested-by: Samuel Ortiz <sameo@linux.intel.com>
Tested-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
Signed-off-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
Pull details of vCPU management (booting, pausing, resuming, shutdown)
into it's own structure. This will ultimately enable this to be moved to
its own file and encapsulate all the vCPU handling for the VMM.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Remove ACPI table creation from arch crate to the vmm crate simplifying
arch::configure_system()
GuestAddress(0) is used to mean no RSDP table rather than adding
complexity with a conditional argument or an Option type as it will
evaluate to a zero value which would be the default anyway.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In vm_reboot, while build the new vm, the old one pointed by self.vm
is not released, that is, the tap opened by self.vm is not closed
either. As a result, the associated dev name slot in host kernel is
still in use state, which prevents the new build from picking it up as
the new opened tap's name, but to use the name in next slot finally.
Call self.vm_shutdown instead here since it has call take() on vm reference,
which could ensure the old vm is destructed before the new vm build.
Signed-off-by: Cathy Zhang <cathy.zhang@intel.com>
Ensure that we tell the allocator about all the I/O ports that we are
using for I/O bus attached devices (serial, i8042, ACPI device.)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In order to group together some functions that can be shared across
virtio transport layers, this commit introduces a new trait called
VirtioTransport.
The first function of this trait being ioeventfds() as it is needed from
both virtio-mmio and virtio-pci devices, represented by MmioDevice and
VirtioPciDevice structures respectively.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Now that kvm-ioctls has been updated, the function unregister_ioevent()
can be used to remove eventfd previously associated with some specific
PIO or MMIO guest address. Particularly, it is useful for the PCI BAR
reprogramming case, as we want to ensure the eventfd will only get
triggered by the new BAR address, and not the old one.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
We need to rely on the latest kvm-ioctls version to benefit from the
recent addition of unregister_ioevent(), allowing us to detach a
previously registered eventfd to a PIO or MMIO guest address.
Because of this update, we had to modify the current constraint we had
on the vmm-sys-util crate, using ">= 0.1.1" instead of being strictly
tied to "0.2.0".
Once the dependency conflict resolved, this commit took care of fixing
build issues caused by recent modification of kvm-ioctls relying on
EventFd reference instead of RawFd.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The specific part of PCI BAR reprogramming that happens for a virtio PCI
device is the update of the ioeventfds addresses KVM should listen to.
This should not be triggered for every BAR reprogramming associated with
the virtio device since a virtio PCI device might have multiple BARs.
The update of the ioeventfds addresses should only happen when the BAR
related to those addresses is being moved.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The PciDevice trait is supposed to describe only functions related to
PCI. The specific method ioeventfds() has nothing to do with PCI, but
instead would be more specific to virtio transport devices.
This commit removes the ioeventfds() method from the PciDevice trait,
adding some convenient helper as_any() to retrieve the Any trait from
the structure behing the PciDevice trait. This is the only way to keep
calling into ioeventfds() function from VirtioPciDevice, so that we can
still properly reprogram the PCI BAR.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Storing a strong reference to the AddressManager behind the
DeviceRelocation trait results in a cyclic reference count.
Use a weak reference to break that dependency.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Based on the value being written to the BAR, the implementation can
now detect if the BAR is being moved to another address. If that is the
case, it invokes move_bar() function from the DeviceRelocation trait.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to trigger the PCI BAR reprogramming from PciConfigIo and
PciConfigMmmio, we need the PciBus to have a hold onto the trait
implementation of DeviceRelocation.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
By implementing the DeviceRelocation trait for the AddressManager
structure, we now have a way to let the PCI BAR reprogramming happen.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to reuse the SystemAllocator later at runtime, it is moved into
the new structure AddressManager. The goal is to have a hold onto the
SystemAllocator and both IO and MMIO buses so that we can use them
later.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In case a VFIO devices is being attached behind a virtual IOMMU, we
should not automatically map the entire guest memory for the specific
device.
A VFIO device attached to the virtual IOMMU will be driven with IOVAs,
hence we should simply wait for the requests coming from the virtual
IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When VFIO devices are created and if the device is attached to the
virtual IOMMU, the ExternalDmaMapping trait implementation is created
and associated with the device. The idea is to build a hash map of
device IDs with their associated trait implementation.
This hash map is provided to the virtual IOMMU device so that it knows
how to properly trigger external mappings associated with VFIO devices.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
With this implementation of the trait ExternalDmaMapping, we now have
the tool to provide to the virtual IOMMU to trigger the map/unmap on
behalf of the guest.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The VFIO container is the object needed to update the VFIO mapping
associated with a VFIO device. This patch allows the device manager
to have access to the VFIO container.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This patch attaches VFIO devices to the virtual IOMMU if they are
identified as they should be, based on the option "iommu=on". This
simply takes care of adding the PCI device ID to the ACPI IORT table.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a VFIO device should be attached to the virtual
IOMMU or not. That's why we introduce an extra option "iommu" with the
value "on" or "off". By default, the device is not attached, which means
"iommu=off".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Fix invalid type for version:
- VmInfo.version.type string
Change Null value from enum as it has problems to build clients with
openapi tools.
- ConsoleConfig.mode.enum Null -> Nil
Signed-off-by: Jose Carlos Venegas Munoz <jose.carlos.venegas.munoz@intel.com>
We should return an explicit error when the transition from on VM state
to another is invalid.
The valid_transition() routine for the VmState enum essentially
describes the VM state machine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to pause a VM, we signal all the vCPU threads to get them out
of vmx non-root. Once out, the vCPU thread will check for a an atomic
pause boolean. If it's set to true, then the thread will park until
being resumed.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
So that we don't need to forward an ExitBehaviour up to the VMM thread.
This simplifies the control loop and the VMM thread even further.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This commit is the glue between the virtio-pci devices attached to the
vIOMMU, and the IORT ACPI table exposing them to the guest as sitting
behind this vIOMMU.
An important thing is the trait implementation provided to the virtio
vrings for each device attached to the vIOMMU, as they need to perform
proper address translation before they can access the buffers.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a virtio-vsock device should be attached to this
virtual IOMMU or not. That's why we introduce an extra option "iommu"
with the value "on" or "off". By default, the device is not attached,
which means "iommu=off".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a virtio-console device should be attached to
this virtual IOMMU or not. That's why we introduce an extra option
"iommu" with the value "on" or "off". By default, the device is not
attached, which means "iommu=off".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a virtio-pmem device should be attached to this
virtual IOMMU or not. That's why we introduce an extra option "iommu"
with the value "on" or "off". By default, the device is not attached,
which means "iommu=off".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a virtio-rng device should be attached to this
virtual IOMMU or not. That's why we introduce an extra option "iommu"
with the value "on" or "off". By default, the device is not attached,
which means "iommu=off".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a virtio-net device should be attached to this
virtual IOMMU or not. That's why we introduce an extra option "iommu"
with the value "on" or "off". By default, the device is not attached,
which means "iommu=off".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Having the virtual IOMMU created with --iommu is one thing, but we also
need a way to decide if a virtio-blk device should be attached to this
virtual IOMMU or not. That's why we introduce an extra option "iommu"
with the value "on" or "off". By default, the device is not attached,
which means "iommu=off".
One side effect of this new option is that we had to introduce a new
option for the disk path, simply called "path=".
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding a simple iommu boolean field to the VmConfig structure so that we
can later use it to create a virtio-iommu device for the current VM.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The virtual IOMMU exposed through virtio-iommu device has a dependency
on ACPI. It needs to expose the device ID of the virtio-iommu device,
and all the other devices attached to this virtual IOMMU. The IDs are
expressed from a PCI bus perspective, based on segment, bus, device and
function.
The guest relies on the topology description provided by the IORT table
to attach devices to the virtio-iommu device.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In case some virtio devices are attached to the virtual IOMMU, their
vring addresses need to be translated from IOVA into GPA. Otherwise it
makes no sense to try to access them, and they would cause out of range
errors.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding virtio feature VIRTIO_F_IOMMU_PLATFORM when explicitly asked by
the user. The need for this feature is to be able to attach the virtio
device to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding virtio feature VIRTIO_F_IOMMU_PLATFORM when explicitly asked by
the user. The need for this feature is to be able to attach the virtio
device to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding virtio feature VIRTIO_F_IOMMU_PLATFORM when explicitly asked by
the user. The need for this feature is to be able to attach the virtio
device to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding virtio feature VIRTIO_F_IOMMU_PLATFORM when explicitly asked by
the user. The need for this feature is to be able to attach the virtio
device to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding virtio feature VIRTIO_F_IOMMU_PLATFORM when explicitly asked by
the user. The need for this feature is to be able to attach the virtio
device to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adding virtio feature VIRTIO_F_IOMMU_PLATFORM when explicitly asked by
the user. The need for this feature is to be able to attach the virtio
device to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The virtio specification defines a device can be reset, which was not
supported by this virtio-console implementation. The reason it is needed
is to support unbinding this device from the guest driver, and rebind it
to vfio-pci driver.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
As of commit 2b94334a, Firecracker includes all the changes we need.
We can now switch to using it instead of carrying a copy.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We used to have errors definitions spread across vmm, vm, api,
and http.
We now have a cleaner separation: All API routines only return an
ApiResult. All VM operations, including the VMM wrappers, return a
VmResult. This makes it easier to carry errors up to the HTTP caller.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to support further use cases where a VM configuration could be
modified through the HTTP API, we only store the passed VM config when
being asked to create a VM. The actual creation will happen when booting
a new config for the first time.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We use the serde crate to serialize and deserialize the VmVConfig
structure. This structure will be passed from the HTTP API caller as a
JSON payload and we need to deserialize it into a VmConfig.
For a convenient use of the HTTP API, we also provide Default traits
implementations for some of the VmConfig fields (vCPUs, memory, etc...).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The linux_loader crate Cmdline struct is not serializable.
Instead of forcing the upstream create to carry a serde dependency, we
simply use a String for the passed command line and build the actual
CmdLine when we need it (in vm::new()).
Also, the cmdline offset is not a configuration knob, so we remove it.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
They point to a vm_virtio structure (VhostUserConfig) and in order to
make the whole config serializable (through the serde crate for
example), we'd have to add a serde dependency to the vm_virtio crate.
Instead we use a local, serializable structure and convert it to
VhostUserConfig from the DeviceManager code.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The kernel path was the only mandatory command line option.
With the addition of the --api-socket option, we can run without a
kernel path and get it later through the API.
Since we can end up with VM configurations that are no longer valid by
default, we need to provide a validation check for it. For now, if the
kernel path is not defined, the VM configuration is invalid.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Cloud Hyper HTTP server runs a synchronous, multi-threaded
loop that receives HTTP requests and tries to call the corresponding
endpoint handlers for the requests URIs.
An endpoint handler will parse the HTTP request and potentially
translate it into and IPC request. The handler holds an notifier and an
mspc Sender for respectively notifying and sending the IPC payload to
the VMM API server. The handler then waits for an API server response
and translate it back into an HTTP response.
The HTTP server is responsible for sending the reponse back to the
caller.
The HTTP server uses a static routes hash table that maps URIs to
endpoint handlers.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cloud-hypervisor API uses HTTP as a transport and is accessible
through a local UNIX socket.
The API root path is /api/v1 and is a collection of RPC-style methods.
All methods are static, unlike typical REST APIs. Variable (e.g. device
IDs) are passed through the request body.
Fixes: #244
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Based off of crosvm revision b5237bbcf074eb30cf368a138c0835081e747d71
add a CMOS device. This environments that can't use KVM clock to get the
current time (e.g. Windows and EFI.)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Refactor the PCI datastructures to move the device ownership to a PciBus
struct. This PciBus struct can then be used by both a PciConfigIo and
PciConfigMmio in order to expose the configuration space via both IO
port and also via MMIO for PCI MMCONFIG.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In order to avoid introducing a dependency on arch in the devices crate
pass the constant in to the IOAPIC device creation.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Using the existing layout module start documenting the major regions of
RAM and those areas that are reserved. Some of the constants have also
been renamed to be more consistent and some functions that returned
constant variables have been replaced.
Future commits will move more constants into this file to make it the
canonical source of information about the memory layout.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
We now start the main VMM thread, which will be listening for VM and IPC
related events.
In order to start the configured VM, we no longer directly call the VM
API but we use the IPC instead, to first create and then start a VM.
Fixes: #303
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Based on the newly defined Cloud Hypervisor IPC, those helpers send
VmCreate and VmStart requests respectively. This will be used by the
main thread to create and start a VM based on the CLI parameters.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This starts the main, single VMM thread, which:
1. Creates the VMM instance
2. Starts the VMM control loop
3. Manages the VMM control loop exits for handling resets and shutdowns.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Unlike the Vmm structure we removed with commit bdfd1a3f, this new one
is really meant to represent the VM monitoring/management object.
For that, we implement a control loop that will replace the one that's
currently embedded within the Vm structure itself.
This will allow us to decouple the VM lifecycle management from the VM
object itself, by having a constantly running VMM control loop.
Besides the VM specific events (exit, reset, stdin for now), the VMM
control loop also handles all the Cloud Hypervisor IPC requests.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The VMM thread and control loop will be the sole consumer of the
EpollContext and EpollDispatch API, so let's move it to lib.rs.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cloud Hypervisor IPC is a simple, mpsc based protocol for threads to
send command to the furture VMM thread. This patch adds the API
definition for that IPC, which will be used by both the main thread
to e.g. start a new VM based on the CLI arguments and the future HTTP
server to relay external requests received from a local Unix domain
socket.
We are moving it to its own "api" module because this is where the
external API (HTTP based) will also be implemented.
The VMM thread will be listening for IPC requests from an mpsc receiver,
process them and send a response back through another mpsc channel.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As we're going to move the control loop to the VMM thread, the exit and
reset EventFds are no longer going to be owned by the VM.
We pass a copy of them when creating the Vm instead.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to handle the VM STDIN stream from a separate VMM thread
without having to export the DeviceManager, we simply add a console
handling method to the Vm structure.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to transfer the control loop to a separate VMM thread, we want
to shrink the VM control loop to a bare minimum.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Once passed to the VM creation routine, a VmConfig structure is
immutable. We can simply carry a Arc of it instead of a reference.
This also allows us to remove any lifetime bound from our VM.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Vmm structure is just a placeholder for the KVM instance. We can
create it directly from the VM creation routine instead.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can integrate the kernel loading into the VM start method.
The VM start flow is then: Vm::new() -> vm.start(), which feels more
natural.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert Path to PathBuf and remove the associated lifetime.
Now we can remove the VmConfig associated lifetime.
Fixes#298
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since vhost-user-blk use same error definition with vhost-user-net,
those errors need define to common usage.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Probe for the size of the host physical address range and use that to
establish the address range for the VM. This removes the limitation on
the size of the VM RAM and gives more space for the devices.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
After the 32-bit gap the memory is shared between the devices and the
RAM. Ensure that the ACPI tables correctly indicate where the RAM ends
and the device area starts by patching the precompiled tables. We get
the following valid output now from the PCI bus probing (8GiB guest)
[ 0.317757] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.319035] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.320215] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.321431] pci_bus 0000:00: resource 7 [mem 0xc0000000-0xfebfffff window]
[ 0.322613] pci_bus 0000:00: resource 8 [mem 0x240000000-0xfffffffff window]
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rerrange "use" statements and make rename variables and fields to
indicate they might be unused.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This removes the register_devices() function with all that functionality
spread across the places where the devices are created.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Mark exit_evt with an underscore it may be unused (it is ignored if the
"acpi" feature is not turned on.)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add (non-default) support for using MMIO for virtio devices. This can be
tested by:
cargo build --no-default-features --features "mmio"
All necessary options will be included injected into the kernel
commandline.
Fixes: #243
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rather than calling it at the very start of the VM execution (i.e. when
the VCPUs are created) do it as part of the DeviceManager creation.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Create the virtio devices independently of adding them to the PCI bus.
Instead accrue the devices in a vector and add them to the bus en-masse.
This will allow the virtio device creation to be used independently of
PCI based transport.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rather than sending a signal to the signal handler used for handling
SIGWINCH calls instead use the crate provided termination method. This
also unregisters the signal handler which also means that there won't be
a leaked signal handler remaining.
This leaked signal handler is what was causing a failure to cleanup up
the thread on subsequent requests breaking two reboots in a row.
Fixes: #252
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
With ACPI disabled there is no way to support both reset and shutdown so
make the VMM exit if the VM is rebootet (via i8042 or triple-fault
reset.)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This commit relies on the new vsock::unix module to create the backend
that will be used from the virtio-vsock device.
The concept of backend is interesting here as it would allow for a vhost
kernel backend to be plugged if that was needed someday.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Based on previous patch introducing the new flag "--vsock", this commit
creates a new virtio-vsock device based on the presence of this flag.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The new flag vsock is meant to be used in order to create a VM with a
virtio-vsock device attached to it. Two parameters are needed with this
device, "cid" representing the guest context ID, and "sock" representing
the UNIX socket path which can be accessed from the host.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The default number of MSI-X vector allocated was 2, which is the minimum
defined by the virtio specification. The reason for this minimum is that
virtio needs at least one interrupt to signal that configuration changed
and at least one to specify something happened regarding the virtqueues.
But this current implementation is not optimal because our VMM supports
as many MSI-X vectors as allowed by the MSI-X specification (2048 max).
For that reason, the current patch relies on the number of virtqueues
needed by the virtio device to determine the right amount of MSI-X
vectors needed. It's important not to forget the dedicated vector for
any configuration change too.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Refactor out DeviceManager into it's own file. This is part of a bigger
effort to reduce complexity in the vm.rs file but will also allow future
separation to allow making PCI support optional.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The command "cargo build --no-default-features" does not recursively
disable the default features across the workspace. Instead add an acpi
feature at the top-level, making it default, and then make that feature
conditional on all the crate acpi features.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
For virtio-fs and virtio-pmem regions of memory are manually mapped into
the address space of the VMM. In order to cleanly reboot we need to
unmap those regions.
Fixes: #223
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Do this by using the same mechanism as the vCPU threads by sending a
signal to the thread. As this is the same mechanism reuse the same code
and rename the "vcpus" member to "threads" to indicate this represents
both the vCPU threads and also the signal handler thread.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Put the ACPI support behind a feature and ensure that the code compiles
without that feature by adding an extra build to Travis.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
As part of the cleanup of the VM shutdown all the vCPU threads. This is
achieved by toggling a shared atomic boolean variable which is checked
in the vCPU loop. To trigger the vCPU code to look at this boolean it is
necessary to send a signal to the vCPU which will interrupt the running
KVM_RUN ioctl.
Fixes: #229
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Being able to reboot requires us to identify all the resources we are
leaking and cleaning those up before we can enable reboot. For now if
the user requests a reboot then shutdown instead.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Sadly only the first few characters of the thread name is preserved so
use a shorter name for the vCPU thread for now. Also give the signal
handling thread a name.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add an I/O port "device" to handle requests from the kernel to shutdown
or trigger a reboot, borrowing an I/O used for ACPI on the Q35 platform.
The details of this I/O port are included in the FADT
(SLEEP_STATUS_REG/SLEEP_CONTROL_REG/RESET_REG) with the details of the
value to write in the FADT for reset (RESET_VALUE) and in the DSDT for
shutdown (S5 -> 0x05)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add a 2nd EventFd to the VM to control resetting (rebooting) the VM this
supplements the EventFd used for managing shutdown of the VM.
The default behaviour on i8042 or triple-fault based reset is currently
unchanged i.e. it will trigger a shutdown.
In order to support restarting the VM it was necessary to make start()
function take a reference to the config.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Only add the ACPI PNP device for the COM1 serial port if it is not
turned off with "--serial off"
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Currently when the VCPU thread exits on an error the VMM continues to
run with no way of shutting down the main thread.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add a revision 2 RSDP table only supporting an XSDT along with support
for creating generic SDT based tables.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This patch factorizes the existing virtio-fs code by relying onto the
common code part of the vhost_user module in the vm-virtio crate.
In details, it factorizes the vhost-user setup, and reuses the error
types defined by the module instead of defining its own types.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
vhost-user-net introduced a new module vhost_user inside the vm-virtio
crate. Because virtio-fs is actually vhost-user-fs, it belongs to this
new module and needs to be moved there.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
