Since each segment must have a non-overlapping memory range associated
with it the device memory must be equally divided amongst all segments.
A new allocator is used for each segment to ensure that BARs are
allocated from the correct address ranges. This requires changes to
PciDevice::allocate/free_bars to take that allocator and when
reallocating BARs the correct allocator must be identified from the
ranges.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
For all the devices that support being hotplugged (disk, net, pmem, fs
and vsock) add "pci_segment" option and propagate that through to the
addition onto the PCI busses.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Move the decision on whether to use a 64-bit bar up to the DeviceManager
so that it can use both the device type (e.g. block) and the PCI segment
ID to decide what size bar should be used.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Generate a set of 8 IRQs and round-robin distribute those over all the
slots for a bus. This same set of IRQs is then used for all PCI
segments.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The platform config may specify a number of PCI segments to use, if this
greater than 1 then we add supplemental PCI segments as well as the
default segment.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This currently contains only the number over PCI segments to create.
This is limited to 16 at the moment which should allow 496 user specified
PCI devices.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
For the bus scanning the GED AML code now calls into a PSCN method that
scans all buses. This approach was chosen since it handles the case
correctly where one GED interrupt is services for two hotplugs on
distinct segments.
The PCIU and PCID field values are now determined by the PSEG field that
is uses to select which segment those values should be used for.
Similarly _EJ0 will notify based on the value of _SEG.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Replace the hardcoded zero PCI segment id when adding devices to the bus
and extend the DeviceTree to hold the PCI segment id.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Since each segment must have disjoint address spaces only advertise
address space in the 32-bit range and the PIO address space on the
default (zero) segment.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Split PciSegment::new_default_segment() into a separate
PciSegment::new() and those parts required only for the default segment
(PIO PCI config device.)
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
For now this still contains just one segment but is expanding in
preparation for more segments.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This commit moves the code that generates the DSDT data for the PCI bus
into PciSegment making no functional changes to the generated AML.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In order to get proper performance out of hardware that might be passed
through the VM with VFIO, we decide to try mapping any region marked as
mappable, ignoring the failure and moving on to the next region. When
the mapping succeeds, we establish a list of user memory regions so that
we enable only subparts of the global mapping through the hypervisor.
This allows MSI-X table and PBA to keep trapping accesses from the guest
so that the VMM can properly emulate MSI-X.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Variables that start with underscore are used to silence rustc.
Normally those variables are not used in code.
This patch drops the underscore from variables that are used. This is
less confusing to readers.
No functional change intended.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
This makes it much easier to use since the info!() level produces far
fewer messages and thus has less overhead.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Create a source archive with vendored sources as part of the release
workflow. This is to enable building the release offline for distros.
Note: The use of realpath and CARGO_HOME are to work around a cargo
vendor bug: https://github.com/rust-lang/cargo/issues/8443.
Signed-off-by: William Douglas <william.douglas@intel.com>
