Ploop image consists of directory with two files: ploop image itself,
called root.hds and DiskDescriptor.xml that contains information about
ploop device: https://openvz.org/Ploop/format.
Such volume are difficult to manipulate in terms of existing volume types
because they are neither a single files nor a directory.
This patch introduces new volume type - ploop. This volume type is used
by ploop volume's exclusively.
Signed-off-by: Olga Krishtal <okrishtal@virtuozzo.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This controller provides a single PCIe port on a new root. It is
similar to pci-expander-bus, intended to provide a bus that can be
associated with a guest-identifiable NUMA node, but is for
machinetypes with PCIe rather than PCI (e.g. q35-based machinetypes).
Aside from PCIe vs. PCI, the other main difference is that a
pci-expander-bus has a companion pci-bridge that is automatically
attached along with it, but pcie-expander-bus has only a single port,
and that port will only connect to a pcie-root-port, or to a
pcie-switch-upstream-port. In order for the bus to be of any use in
the guest, it must have either a pcie-root-port or a
pcie-switch-upstream-port attached (and one or more
pcie-switch-downstream-ports attached to the
pcie-switch-upstream-port).
This is a standard PCI root bus (not a bridge) that can be added to a
440fx-based domain. Although it uses a PCI slot, this is *not* how it
is connected into the PCI bus hierarchy, but is only used for
control. Each pci-expander-bus provides 32 slots (0-31) that can
accept hotplug of standard PCI devices.
The usefulness of pci-expander-bus relative to a pci-bridge is that
the NUMA node of the bus can be specified with the <node> subelement
of <target>. This gives guest-side visibility to the NUMA node of
attached devices (presuming that management apps only assign a device
to a bus that has a NUMA node number matching the node number of the
device on the host).
Each pci-expander-bus also has a "busNr" attribute. The expander-bus
itself will take the busNr specified, and all buses that are connected
to this bus (including the pci-bridge that is automatically added to
any expander bus of model "pxb" (see the next commit)) will use
busNr+1, busNr+2, etc, and the pci-root (or the expander-bus with next
lower busNr) will use bus numbers lower than busNr.
This is especially useful for "bus", since the bus of a device's pci
address is matched to the "index" of a controller to determine which
bus it will be connected to, and "index" is always specified in
decimal - being able to specify both in decimal at least makes it
easier to assure a device is being assigned to the correct bus when it
is added. For the other attributes, it is just a convenience.
(MB: the parser already allows for any of these attributes to be given
in decimal, and there are even examples floating around on the
internet that give them in decimal rather than hex (written in the
days before virsh did schema validation on all XML). This only updates
the schema to match the parser.)
nwfilter.rng defines uint16range and uint32range, but in a different
manner (it also allows a variable name as the value, rather than just
a decimal or hex number). I wanted to add uint16range to
basictypes.rng, but my desired definition was parallel to those for
uint8range and uint24range which are defined in basictypes.rng - they
*don't* allow a variable name for the value.
The simplest path to make everyone happy is to make the "plain"
versions in basictypes.rng have simpler names - "uint8", "uint16", and
"uint24". This patch renames uint8range and uint24range to uint8 and
uint24, while the next patch will add uint16.
The pcie-switch-downstream-port and pcie-root-port controllers have
only a single slot, numbered 0, and the greate majority of all guest
PCI devices are plugged into function 0 of whatever slot they're
using. The parser makes these optional, setting them to 0 when not
specified, and it's logical for the schema to also make them optional.
This cleanups the documentation, reformat some of the paragraphs to use
<p> instead of </br> and rewrites the listen part to be more extendable.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
According to MDN[1], 'margin-left' and similar CSS properties,
including 'margin-right', cannot be applied to the '::first-line'
pseudo-element, so this rule will never have any effect and can
be safely removed.
[1] https://developer.mozilla.org/en/docs/Web/CSS/::first-line
This patch adds new xml element, and so we can have the option of
also having perf events enabled immediately at startup.
Signed-off-by: Qiaowei Ren <qiaowei.ren@intel.com>
Message-id: 1459171833-26416-6-git-send-email-qiaowei.ren@intel.com
While we have a wiki page describing the feature [1] since the
feature is distributed in our .tar.gz we ought to document it. So
I went ahead, copied the wiki page and reformatted so it fits our
docs coding style.
1: http://wiki.libvirt.org/page/NSS_module
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
- remove top padding for h1. this means page titles sit flush with the top
of the side bar (like 'The virtualization API' on the front page)
- up the top padding for the remaining sections. makes it visually easier
to tell adjacent header sections apart, especially in dense wiki pages
- use two different spacing levels for h2-h4 and h5-h6,
gives pages some more visual flexibility
- use a slightly lower bottom padding... this makes top padding stick out
more which makes it visually easier to differentiate between adjacent
header sections
In order to follow recent comments which indicate support for specific
feature bits are supported by a specific QEMU version add the version
from whence the relaxed, vapic, and spinlocks support was added.
This patch adds support for "vpindex", "runtime", "synic",
"stimer", and "vendor_id" features available in qemu 2.5+.
- When Hyper-V "vpindex" is on, guest can use MSR HV_X64_MSR_VP_INDEX
to get virtual processor ID.
- Hyper-V "runtime" enlightement feature allows to use MSR
HV_X64_MSR_VP_RUNTIME to get the time the virtual processor consumes
running guest code, as well as the time the hypervisor spends running
code on behalf of that guest.
- Hyper-V "synic" stands for Synthetic Interrupt Controller, which is
lapic extension controlled via MSRs.
- Hyper-V "stimer" switches on Hyper-V SynIC timers MSR's support.
Guest can setup and use fired by host events (SynIC interrupt and
appropriate timer expiration message) as guest clock events
- Hyper-V "reset" allows guest to reset VM.
- Hyper-V "vendor_id" exposes hypervisor vendor id to guest.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
When reading in an XML definition for a SCSI target device, the name
property of struct scsi_target refers to the @target element.
Let's fix this obvious typo and also extend the XML schema to provide
validation.
Signed-off-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Most hypervisors use Hardware Assisted Paging by default and don't
require specifying the feature in domain conf. But some hypervisors
support disabling HAP on a per-domain basis. To enable HAP by default
yet provide a knob to disable it, extend the <hap> feature with a
'state=on|off' attribute, similar to <pvspinlock> and <vmport> features.
In the absence of <hap>, the hypervisor default (on) is used. <hap>
without the state attribute would be the same as <hap state='on'/> for
backwards compatibility. And of course <hap state='off'/> disables hap.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
If we expose this information, which is one byte in every PCI config
file, we let all mgmt apps know whether the device itself is an endpoint
or not so it's easier for them to decide whether such device can be
passed through into a VM (endpoint) or not (*-bridge).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1317531
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The docs claims the cache attribute of the disk <driver>
element supports 'default' as one of its permissible values,
but such configuration fails virt-xml-validate. Add 'default'
as one of the cache attribute choices in domaincommon.rng.
- Add line-height:150% spacing for all text. This makes text lines far
less cramped, and seems closer visually to what wikipedia uses.
- Remove bottom and top margin from lists: entries seemed needlessly
spread out.
- Reduce sublist indentation a bit
- Add a bottom border after headings: IMO this greatly helps in break
up the vertical flow of a big page of text. Doesn't look great on the
front page, but helps a lot on dense pages like formatdomain
- change font-family to just 'sans-serif' rather than hardcode a few
font families. this means we abide the user's browser font setting,
and makes us consistent with other sites like en.wikipedia.org
- raise font-size to 90%. this is what en.wikipedia.org uses.
With these two tweaks, libvirt.org text renders the same as
en.wikipedia.org with fedora firefox out of the box config. Previously
the font on libvirt.org was very small and difficult to read.
Extend the chardev source XML so that there is a new optional
<log/> element, which is applicable to all character device
backend types. For example, to log output of a TCP backed
serial port
<serial type='tcp'>
<source mode='connect' host='127.0.0.1' service='9999'/>
<protocol type='raw'/>
<log file='/var/log/libvirt/qemu/demo-serial0.log' append='on'/>
<target port='0'/>
</serial>
Not all hypervisors will support use of logfiles.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This parameter represents top level period cgroup
that limits whole domain enforcement period for a quota
Signed-off-by: Alexander Burluka <aburluka@virtuozzo.com>
This attribute is used to extend secondary PCI bar and expose it to the
guest as 64bit memory. It works like this: attribute vram is there to
set size of secondary PCI bar and guest sees it as 32bit memory,
attribute vram64 can extend this secondary PCI bar. If both attributes
are used, guest sees two memory bars, both address the same memory, with
the difference that the 32bit bar can address only the first part of the
whole memory.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1260749
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Add Spice graphics gl attribute. qemu 2.6 should have -spice gl=on argument to
enable opengl rendering context (patches on the ML). This is necessary to
actually enable virgl rendering.
Add a qemuxml2argv test for virtio-gpu + spice with virgl.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Imagine you have partially installed libvirt, or maybe you're
just running 'make uninstall' from a different version than 'make
install' has been ran. One way or another, we are doing plain
'rm' instead of 'rm -f' and thus not trying hard enough when
uninstalling. In the rest of our code we stick with -f switch. Do
that for docs too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Recent changes to the handling of GIC version, specifically commit
2a7b11eafb, have clearly defined what values are acceptable for the
version attribute of the <gic> element. Update the documentation
accordingly.
This change allows to use "host" as a GIC version in the domain XML.
Since we'll need to update the virGICVersion enumeration to support
new GIC versions anyway, it makes sense to be a bit more strict in
the schema as well and reject values that are not in the enumeration.
When generating docs in a VPATH build we get a failure to
create a file due to the 'internals' subdir not existing:
Generating internals/locking.html.tmp
/bin/sh: line 3: internals/locking.html.tmp: No such file or directory
rm: cannot remove ‘internals/locking.html.tmp’: No such file or directory
Makefile:2229: recipe for target 'internals/locking.html.tmp' failed
make: *** [internals/locking.html.tmp] Error 1
For some reason, make has decided to run the target
%.html.tmp: %.html.in site.xsl page.xsl sitemap.html.in $(acl_generated)
instead of the target
internals/%.html.tmp: internals/%.html.in subsite.xsl page.xsl sitemap.html.in
Removing '$(acl_generated)' from the first target, inexplicably
causes make to now run the correct target for the internals/
files.
Rather than figure this out, lets just combine the two targets
into one.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Add a new storage pool source device attribute 'part_separator=[yes|no]'
in order to allow a 'disk' storage pool using a device mapper multipath
device to not add the "p" partition separator to the generated device
name when libvirt_parthelper is run.
This will allow libvirt to find device mapper multipath devices which were
configured in /etc/multipath.conf to use 'user_friendly_names' or custom
'alias' names for the LUN.
So after da176bf6b7 and friend we have switched to $(wildcard
some/path/*.xml) instead of enumerating the files explicitly.
This is nice, however it makes distcheck build from VPATH fail.
The reason is that it's is not obvious to what does the wildcard
refer to: srcdir or builddir?
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Excessive memory balloon inflation can cause invocation of OOM-killer,
when Linux is under severe memory pressure. QEMU memballoon device
has a feature to release some memory at the last moment before some
process will be get killed by OOM-killer.
Introduce a new optional balloon device attribute 'autodeflate' to
enable or disable this feature.
If no port number was provided for a storage pool libvirt defaults to
port 6789; however, librbd/librados already default to 6789 when no port
number is provided.
In the future Ceph will switch to a new port for the Ceph monitors since
port 6789 is already assigned to a different application by IANA.
Port 6789 is assigned to SMC-HTTPS and Ceph now has port 3300 assigned as
the 'Ceph monitor' port.
In this case it is the best solution to not hardcode any port number into
libvirt and let librados handle the connection.
Only if a user specifies a different port number we pass it down to librados,
otherwise we leave it blank.
Signed-off-by: Wido den Hollander <wido@widodh.nl>
merge
Allow <name> and <uuid> anywhere under <domain>, not just at the top:
error:XML document failed to validate against schema: Unable to validate
doc against /usr/share/libvirt/schemas/domain.rng
Expecting an element name, got nothing
Invalid sequence in interleave
Element domain failed to validate content
Introduced with the first RelaxNG schema in commit c642103.
https://bugzilla.redhat.com/show_bug.cgi?id=1292131
The documentation (and comment in libvirtd.conf) says that the text in
a log filter is compared to the "source file name", and gives the
example of "util/json", but this is not correct (at least not since
commit 2835c1e, possibly earlier). It is instead compared to the
string given in the VIR_LOG_INIT() macro invocation at the top of each
source file, which is always "similar to but not the same as" the
source file name (in the example above, the proper name is
"util.json", while the file name is "util/virjson.c"). This patch
corrects the misstatement in both the documentation and in
libvirtd.conf.
Currently, there is no possibility for user to specify desired behaviour of
output to file - truncate or append. This patch adds an ability to explicitly
specify that user wants to preserve file's content on reopen.
Signed-off-by: Dmitry Mishin <dim@virtuozzo.com>
Using more than 4TiB of memory per NUMA node would not be possible to
express in the XML without violating the schema. Not that such boxes
would be common, but we should use a longer type at this point.
The pattern is not necessary since libvirt redefines the type already in
basictypes.rng with the same pattern.
To be used by the family of virtio input devices:
<input type='mouse' bus='virtio'/>
<input type='tablet' bus='virtio'/>
<input type='keyboard' bus='virtio'/>
https://bugzilla.redhat.com/show_bug.cgi?id=1231114
As it turned out, we need to share some enums and declarations between
libvirt.h and libvirt-admin.h, but since our policy forbids direct includes of
libvirt*.h, there has to be some header exempt from this rule. This patch moves
the relevant part of code from libvirt.h.in to libvirt-common.h.in. Moreover,
since there is no need to have libvirt.h generated anymore, introduce a new
header libvirt.h which was previosly ignored from git and make the common
header ignored and generated instead.
qemu 2.5 provides virtio video device. It can be used with -device
virtio-vga for primary devices, or -device virtio-gpu for non-vga
devices. However, only the primary device (VGA) is supported with this
patch.
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=1195176
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
'model' attribute was added to a panic device but only one panic
device is allowed. This patch changes panic device presence
from 'optional' to 'zeroOrMore'.
Libvirt already has two types of panic devices - pvpanic and pSeries firmware.
This patch introduces the 'model' attribute and a new type of panic device.
'isa' model is for ISA pvpanic device.
'pseries' model is a default value for pSeries guests.
'hyperv' model is the new type. It's used for Hyper-V crash.
Schema and docs are updated for the new attribute.
Report the maximum possible number of VFs for an SRIOV PF, like this:
<capability type='virtual_functions' maxCount='7'>
...
</capability>
I've just discovered that the virtual_functions and physical_functions
capabilities are not supported in the virNodeDeviceParse functions,
only in virNodeDeviceFormat (I suppose because they are only reported,
not set from XML). This should probably be remedied, but is less
immediately useful than the current patch.
Adjust the config code so that it does not enforce that target memory
node is specified. To avoid breakage, adjust the qemu memory hotplug
config checker to disallow such config for now.
We have twice previously attempted to remove Xenner
support
commit de9be0ab4d
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Wed Aug 22 17:29:01 2012 +0100
Remove xenner support
commit 92572c3d71
Author: Ján Tomko <jtomko@redhat.com>
Date: Wed Feb 18 16:33:50 2015 +0100
Remove code handling the QEMU_CAPS_DOMID capability
This change really does remove the last traces of it
in the capabilities handling code
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Check the QEMU version and refuse to work with QEMU versions
older than 0.12.0. This is approximately the vintage of QEMU
that is available in RHEL-6 era distros.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This has been broken for a looong time - in fact, we've been
shipping a mostly-empty NEWS file for at least the past two years.
Including the html namespace and using it for matching elements,
like hacking1.xsl and hacking2.xsl were already doing, makes the
NEWS file useful again.
Add a note explaining that the release list has been split up
by year as well.
There were some inconsistencies, eg. the number of digits used for
the day. The month name was also spelled out instead of abbreviated
in some instances.
There were some inconsistencies; now the section title is always
one of Bug Fixes, Cleanups, Documentation, Features, Improvements,
Portability, Security.
Some of the paragraphs were not properly indented: while this was
not a problem in the HTML version, you could tell the difference
in the plain text version.
The changes for releases earlier than 0.7.1 were mostly lumped
together as opposed to being tidly organized with one change per
line, like we have done from that point onwards.
As a result, they look awful in the HTML version and don't work
too well in the plain text version either.
Luckily, except for the very first releases, the information is
still very detailed, so it's enough to organize it properly.
The changes for releases earlier than 0.7.1 were mostly lumped
together as opposed to being tidly organized with one change per
line, like we have done from that point onwards.
As a result, they look awful in the HTML version and don't work
too well in the plain text version either.
Luckily, except for the very first releases, the information is
still very detailed, so it's enough to organize it properly.
The changes for releases earlier than 0.7.1 were mostly lumped
together as opposed to being tidly organized with one change per
line, like we have done from that point onwards.
As a result, they look awful in the HTML version and don't work
too well in the plain text version either.
Luckily, except for the very first releases, the information is
still very detailed, so it's enough to organize it properly.
The description for this release, unlike all other descriptions,
was inside a <p> element; however, the XSLT stylesheet contains a
template that drops all <p> elements from the output file, so it
never made it to the generated NEWS file.
Use a <li> element, same as all other releases, instead.
The example pvspinlock XML is:
<pvspinlock/>
While this is accepted by libvirt and works correctly, it's currently
always output as a tristate like
<pvspinlock state='on'/>
So document that format instead
We have a new libvirt-appdev-guide-python which we need to
promote to users. Rewrite the existing page to mention it
too. Also use the new URL location which is automatically
refreshed once a day.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This reverts commit e5470dd0e0.
This has been ACK'd by the original author in the original mail thread:
https://www.redhat.com/archives/libvir-list/2015-September/msg00310.html
The reason to revert this is due to the patch breaking the generation of
internal subsites. The original issue still needs to be dealt with,
though.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Double semicolons have special meaning in makefiles, but they would have
to be combined with other rules witch such separators in order to be
used as intended. Since there are no other rules like that, let's
clean it up.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Creating ACL rules is not exactly easy and existing examples are pretty
simple. This patch adds a somewhat complex example which defines several
roles. Admins can do everything, operators can do basic operations
on any domain and several groups of users who act as operators but only
on a limited set of domains.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Adds a new interface type using UDP sockets, this seems only applicable
to QEMU but have edited tree-wide to support the new interface type.
The interface type required the addition of a "localaddr" (local
address), this then maps into the following xml and qemu call.
<interface type='udp'>
<mac address='52:54:00:5c:67:56'/>
<source address='127.0.0.1' port='11112'>
<local address='127.0.0.1' port='22222'/>
</source>
<model type='virtio'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/>
</interface>
QEMU call:
-net socket,udp=127.0.0.1:11112,localaddr=127.0.0.1:22222
Notice the xml "local" entry becomes the "localaddr" for the qemu call.
reference:
http://lists.gnu.org/archive/html/qemu-devel/2011-11/msg00629.html
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This patch adds feature for lxc containers to inherit namespaces.
This is very similar to what lxc-tools or docker provides. Look
for "man lxc-start" and you will find that you can pass command
args as [ --share-[net|ipc|uts] name|pid ]. Or check out docker
networking option in which you can give --net=container:NAME_or_ID
as an option for sharing +namespace.
>From this patch you can add extra libvirt option to share
namespace in following way.
<lxc:namespace>
<lxc:sharenet type='netns' value='red'/>
<lxc:shareipc type='pid' value='12345'/>
<lxc:shareuts type='name' value='container1'/>
</lxc:namespace>
The netns option is specific to sharenet. It can be used to
inherit from existing network namespace.
Co-authored: Daniel P. Berrange <berrange@redhat.com>
This controller can be connected only to a port on a
pcie-switch-upstream-port. It provides a single hotpluggable port that
will accept any PCI or PCIe device, as well as any device requiring a
pcie-*-port (the only current example of such a device is the
pcie-switch-upstream-port).
This controller can be connected only to a pcie-root-port or a
pcie-switch-downstream-port (which will be added in a later patch),
which is the reason for the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_PORT. A pcie-switch-upstream-port provides
32 ports (slot=0 to slot=31) on the downstream side, which can only
have pci controllers of model "pcie-switch-downstream-port" plugged
into them, which is the reason for the other new connect type
VIR_PCI_CONNECT_TYPE_PCIE_SWITCH.
This controller can be connected (at domain startup time only - not
hotpluggable) only to a port on the pcie root complex ("pcie-root" in
libvirt config), hence the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_ROOT. It provides a hotpluggable port that
will accept any PCI or PCIe device.
New attributes must be added to the controller <target> subelement for
this - chassis and port are guest-visible option values that will be
set by libvirt with values derived from the controller's index and pci
address information.
There are some configuration options to some types of pci controllers
that are currently automatically derived from other parts of the
controller's configuration. For example, in qemu a pci-bridge
controller has an option that is called "chassis_nr"; up until now
libvirt has always set chassis_nr to the index of the pci-bridge. So
this:
<controller type='pci' model='pci-bridge' index='2'/>
will always result in:
-device pci-bridge,chassis_nr=2,...
on the qemu commandline. In the future we may decide there is a better
way to derive that option, but even in that case we will need for
existing domains to retain the same chassis_nr they were using in the
past - that is something that is visible to the guest so it is part of
the guest ABI and changing it would lead to problems for migrating
guests (or just guests with very picky OSes).
The <target> subelement has been added as a place to put the new
"chassisNr" attribute that will be filled in by libvirt when it
auto-generates the chassisNr; it will be saved in the config, then
reused any time the domain is started:
<controller type='pci' model='pci-bridge' index='2'>
<model type='pci-bridge'/>
<target chassisNr='2'/>
</controller>
The one oddity of all this is that if the controller configuration
is changed (for example to change the index or the pci address
where the controller is plugged in), the items in <target> will
*not* be re-generated, which might lead to conflict. I can't
really see any way around this, but fortunately if there is a
material conflict qemu will let us know and we will pass that on
to the user.
This new subelement is used in PCI controllers: the toplevel
*attribute* "model" of a controller denotes what kind of PCI
controller is being described, e.g. a "dmi-to-pci-bridge",
"pci-bridge", or "pci-root". But in the future there will be different
implementations of some of those types of PCI controllers, which
behave similarly from libvirt's point of view (and so should have the
same model), but use a different device in qemu (and present
themselves as a different piece of hardware in the guest). In an ideal
world we (i.e. "I") would have thought of that back when the pci
controllers were added, and used some sort of type/class/model
notation (where class was used in the way we are now using model, and
model was used for the actual manufacturer's model number of a
particular family of PCI controller), but that opportunity is long
past, so as an alternative, this patch allows selecting a particular
implementation of a pci controller with the "name" attribute of the
<model> subelement, e.g.:
<controller type='pci' model='dmi-to-pci-bridge' index='1'>
<model name='i82801b11-bridge'/>
</controller>
In this case, "dmi-to-pci-bridge" is the kind of controller (one that
has a single PCIe port upstream, and 32 standard PCI ports downstream,
which are not hotpluggable), and the qemu device to be used to
implement this kind of controller is named "i82801b11-bridge".
Implementing the above now will allow us in the future to add a new
kind of dmi-to-pci-bridge that doesn't use qemu's i82801b11-bridge
device, but instead uses something else (which doesn't yet exist, but
qemu people have been discussing it), all without breaking existing
configs.
(note that for the existing "pci-bridge" type of PCI controller, both
the model attribute and <model> name are 'pci-bridge'. This is just a
coincidence, since it turns out that in this case the device name in
qemu really is a generic 'pci-bridge' rather than being the name of
some real-world chip)
"Further" clarification (and testing) shows that using a SCSI Fibre
Channel NPIV device/lun from a storage pool as a <disk type='volume'
device'lun'> will work. So just add that to the allowable options
Related to: https://bugzilla.redhat.com/show_bug.cgi?id=1230179
Rather than calling virDomainHostdevAssignAddress during the parsing
of the XML, move the setting of a default hostdev address to domain/
device post processing.
Since the parse code no longer generates an address, we can remove
the virDomainDefMaybeAddHostdevSCSIcontroller since the call to
virDomainHostdevAssignAddress will attempt to add the controllers
that were not already defined in the XML.
This patch will also enforce that the address type is type 'drive'
when a SCSI subsystem <hostdev> element is provided with an <address>.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Adding functionality to libvirt that will allow
it query the interface for the availability of RDMA and
tx-udp_tnl-segmentation Offloading NIC capabilities
Here is an example of the feature XML definition:
<device>
<name>net_eth4_90_e2_ba_5e_a5_45</name>
<path>/sys/devices/pci0000:00/0000:00:03.0/0000:08:00.1/net/eth4</path>
<parent>pci_0000_08_00_1</parent>
<capability type='net'>
<interface>eth4</interface>
<address>90:e2:ba:5e:a5:45</address>
<link speed='10000' state='up'/>
<feature name='rx'/>
<feature name='tx'/>
<feature name='sg'/>
<feature name='tso'/>
<feature name='gso'/>
<feature name='gro'/>
<feature name='rxvlan'/>
<feature name='txvlan'/>
<feature name='rxhash'/>
<feature name='rdma'/>
<feature name='txudptnl'/>
<capability type='80203'/>
</capability>
</device>
The information on companion controllers we give in our documentation is
rather sparse. For example, it looks like any controller can be used as
a companion one. Also, when using ich9-uhci2, for example, we are able
to set some sensible defaults, but it might get confusing for the user
as we don't do that for all controller models.
https://bugzilla.redhat.com/show_bug.cgi?id=1069590
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Update the descriptions for disk and hostdev sgio in order to indicate
not all hypervisors and OS's support this feature
Signed-off-by: John Ferlan <jferlan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1232606
Since an mpath pool contains all the Multipath devices on a host, allowing
more than one defined on a host at a time should be disallowed under the
policy of disallowing duplicate source pools for the host.
Adjust to docs to clarify the Multipath target path value usage for both
the storage driver (only 1 pool per host) and formatstorage references
(ignore the target element in favor of the default target mapping of
/dev/mapper).
Don't listen on the admin socket in the daemon and comment out the
admin devel files out of specfile.
Library is still being compiled and installed in order to link easily
without any disturbing modifications to the daemon code.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
While re-reading what I wrote for commit id '785a8940e', I realized
I needed to clarify that being able to present as a 'lun', the mode
property for the pool source element needed to be "host" (or empty)
and not "direct".
It was described correctly later in the mode host description, but
this just ensures it's not missed here as well.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Also move the mention of version numbers for the various PCI
controller models up to the end of the sentence where they are first
given, to avoid confusion.
When support for the pcie-root and dmi-to-pci-bridge buses on a Q35
machinetype was added, I was concerned that even though qemu at the
time allowed plugging a PCI device into a PCIe port, that it might not
be supported in the future. To prevent painful backtracking in the
possible future where this happened, I disallowed such connections
except in a few specific cases requested by qemu developers (indicated
in the code with the flag VIR_PCI_CONNECT_TYPE_EITHER_IF_CONFIG).
Now that a couple years have passed, there is a clear message from
qemu that there is no danger in allowing PCI devices to be plugged
into PCIe ports. This patch eliminates
VIR_PCI_CONNECT_TYPE_EITHER_IF_CONFIG and changes the code to always
allow PCI->PCIe or PCIe->PCI connection *when the PCI address is
specified in the config. (For newly added devices that haven't yet
been given a PCI address, the auto-placement still prefers using the
correct type of bus).
In my previous fix (1310b1358) I've tried to solve an ordering
issue. Well, while it worked it has a side effect of keeping a
temporary file around. My patch was buggy in that sense. Solve
this by properly marking the dependency without any side effect.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch provides support for the new watchdog model "diag288".
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
This patch provides support for a new watchdog action "inject-nmi" which
allows to define an inject of a non-maskable interrupt into a guest.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
The acl.html file includes aclperms.htmlinc which is generated.
However, acl.html is generated too from acl.html.tmp. And in fact,
this is the place where the aclperms file is needed. Fix the
dependency in Makefile.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Currently the grammar uses "none" for a "valid" Disk Storage Pool
format type; however, virStoragePoolFormatDisk uses "unknown" so
virt-xml-validate will fail to validate when "unknown" is found
The type='scsi' parameter of an address element is ignored
if placed within a hostdev section, and rejected by the XML
schema used by virt-xml-validate. Remove it from the doc,
and correct a typo in the remaining address arguments.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Defining a domain with a SCSI disk attached via a hostdev
tag and a source address unit value longer than two digits
causes an error when editing the domain with virsh edit,
even if no changes are made to the domain definition.
The error suggests invalid XML, somewhere:
# virsh edit lmb_guest
error: XML document failed to validate against schema:
Unable to validate doc against /usr/local/share/libvirt/schemas/domain.rng
Extra element devices in interleave
Element domain failed to validate content
The virt-xml-validate tool fails with a similar error:
# virt-xml-validate lmb_guest.xml
Relax-NG validity error : Extra element devices in interleave
lmb_guest.xml:17: element devices: Relax-NG validity error :
Element domain failed to validate content
lmb_guest.xml fails to validate
The hostdev tag requires a source address to be specified,
which includes bus, target, and unit address attributes.
According to the SCSI Architecture Model spec (section
4.9 of SAM-2), a LUN address is 64 bits and thus could be
up to 20 decimal digits long. Unfortunately, the XML
schema limits this string to just two digits. Similarly,
the target field can be up to 32 bits in length, which
would be 10 decimal digits.
# lsscsi -xx
[0:0:19:0x4022401100000000] disk IBM 2107900 3.44 /dev/sda
# lsscsi
[0:0:19:1074872354]disk IBM 2107900 3.44 /dev/sda
# cat lmb_guest.xml
<domain type='kvm'>
<name>lmb_guest</name>
<memory unit='MiB'>1024</memory>
...trimmed...
<devices>
<controller type='scsi' model='virtio-scsi' index='0'/>
<hostdev mode='subsystem' type='scsi'>
<source>
<adapter name='scsi_host0'/>
<address bus='0' target='19' unit='1074872354'/>
</source>
</hostdev>
...trimmed...
Since the reference unit and target fields are used in
several places in the XML schema, create a separate one
specific for SCSI Logical Units that will permit the
greater length. This permits both the validation utility
and the virsh edit command to succeed when a hostdev
tag is included.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1220527
This type of information defines attributes of a system
baseboard. With one exception: board type is yet not implemented
in qemu so it's not introduced here either.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since the background for Admin API is merged upstream, we are bumping
the minor release version as discussed previously
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
No online docs are build from it since it doesn't really fit into our
document structure and new page will need to be created for it, but this
is at least a heads-up commit for easier parsing in order to build some
documentation (or python bindings) later on.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1186969
When generating the path to the dir for a CIFS/Samba driver, the code
would generate a source path for the mount using "%s:%s" while the
mount.cifs expects to see "//%s/%s". So check for the cifsfs and
format the source path appropriately.
Additionally, since there is no means to authenticate, the mount
needs a "-o guest" on the command line in order to anonymously mount
the Samba directory.
Commit id '887dd362' added support for a netfs pool format type 'cifs'
and 'gluster' in order to add rng support for Samba and glusterfs netfs
pools. Originally, the CIFS type support was added as part of commit
id '61fb6979'. Eventually commit id 'b325be12' fixed the gluster rng
definition to match expectations.
As it turns out the CIFS rng needed a similar change since the directory
path is not an absDirPath, rather just a dirPath will be required.
https://bugzilla.redhat.com/show_bug.cgi?id=1021480
Seems the property has been deprecated for qemu, although seemingly ignored.
This patch enforces from a libvirt perspective that a scsi-block 'lun'
device should not provide the 'serial' property.
https://bugzilla.redhat.com/show_bug.cgi?id=1228007
When attaching a scsi volume lun via the attach-device --config or
--persistent options, there was no translation of the source pool
like there was for the live path, thus the attempt to modify the config
would fail since not enough was known about the disk.
I see no reason to duplicate this list of architectures. This also allows
more guest architectures to be used with libvirt (like the mips64el qemu
machine I am trying to run).
Signed-off-by: James Cowgill <james410@cowgill.org.uk>
This patch adds the support of queues attribute of the driver element
for vhost-user interface type. Example:
<interface type='vhostuser'>
<mac address='52:54:00:ee:96:6d'/>
<source type='unix' path='/tmp/vhost2.sock' mode='client'/>
<model type='virtio'/>
<driver queues='4'/>
</interface>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1207692
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If a macro has a string value, the @string attribute will contain the
value. Otherwise @string attribute will be missing.
For example, the following macro definition from libvirt-domain.h:
/**
* VIR_MIGRATE_PARAM_URI:
* ...
*/
# define VIR_MIGRATE_PARAM_URI "migrate_uri"
will result in
<macro name='VIR_MIGRATE_PARAM_URI' file='libvirt-domain' string='migrate_uri'>
<info><![CDATA[...]]></info>
</macro>
https://bugzilla.redhat.com/show_bug.cgi?id=1229199
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
The network name is currently of type "deviceName" but it should be
"text" as name is defined in the network.rng.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
The guest firmware provides the same functionality as the pvpanic
device, and the relevant element should always be present in the
domain XML to reflect this fact, so add it after parsing the
definition if it wasn't there already.
The guest firmware provides the same functionality as the pvpanic
device, which is not available in QEMU on pSeries, so the domain
XML should be allowed to contain the <panic> element.
On the other hand, unlike the pvpanic device, the guest firmware
can't be configured, so report an error if an address has been
provided in the XML.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182388
The XML parser sets a default <mode> if none is explicitly passed in.
This is then used at pool/vol creation time, and unconditionally reported
in the XML.
The problem with this approach is that it's impossible for other code
to determine if the user explicitly requested a storage mode. There
are some cases where we want to make this distinction, but we currently
can't.
Handle <mode> parsing like we handle <owner>/<group>: if no value is
passed in, set it to -1, and adjust the internal consumers to handle
it.
- Don't redocument the permissions fields for backingstore, just point to
the volume docs.
- Clarify that owner/group are inherited from the parent directory at
volume create/pool build time.
- Clarify that <permissions> fields report runtime values too
In the upstream discussion on creating a github mirror [1], it turned
out that there are some read-only mirrors of our repository. Lets
advertise them on our downloads page. But do it wisely and discourage
people in sending a pull requests on GitHub.
1: https://www.redhat.com/archives/libvir-list/2015-May/msg00775.html
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of netcf-0.2.8, netcf supports configuring multipl IPv4 addresses,
as well as simultaneously configuring dhcp and static IPv4 addresses,
on a single interface. This patch updates libvirt's interface.rng to
allow such configurations.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1223688
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Like usb-serial, the pci-serial device allows a serial device to be
attached to PCI bus. An example XML looks like this:
<serial type='dev'>
<source path='/dev/ttyS2'/>
<target type='pci-serial' port='0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</serial>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Two new domain configuration XML elements are added to enable/disable
the protected key management operations for a guest:
<domain>
...
<keywrap>
<cipher name='aes|dea' state='on|off'/>
</keywrap>
...
</domain>
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1171984https://bugzilla.redhat.com/show_bug.cgi?id=1188463
Remove the check for the source host name for iSCSI source XML processing
declaring duplicate sources when the source device path and if present the
initiator of a proposed storage pool matches an existing storage pool.
The backend iSCSI storage driver uses 'iscsiadm --mode session' to query
available iscsid target sessions. The output displayed is the IP address
and the IQN (target path) of known targets. The displayed IP address
is a resolved address based on the session --login. Additionally, iscsid
keeps track of the various ways to define the host name (IPv4 Address,
IPv6 Address, /etc/hosts, etc.) for that IQN (see output of an 'iscsiadm
--mode node'). If an incoming IQN matches and the host name provided by
libvirt is resolved to the existing IQN, then iscsid will "reuse" the
session. Although libvirt could do the same name resolution, if there
is a difference, iscsid could still declare two seemingly different sources
to be the same and not create a new session which means libvirt now has
two storage pools looking at the same source. Thus to avoid any strange
host name resolution issues, just rely on iscsid for that and do not
allow multiple pools on the same host to use the same device path (IQN).
Some platforms, like aarch64, don't have APIC but GIC. So there's
no reason to have <apic/> feature turned on. However, we are
still missing <gic/> feature. This commit introduces the feature
to XML parser and formatter, adds documentation and updates RNG
schema.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
A new feature that can be turned on or off.
The QEMU machine vmport option allows to set the VMWare IO port
emulation. This emulation is useful for absolute pointer input when the
guest has vmware input drivers, and is enabled by default for kvm.
However it is unnecessary for Spice-enabled VM, since the agent already
handles absolute pointer and multi-monitors. Furthermore, it prevents
Spice from switching to relative input since the regular ps/2 pointer
driver is replaced by the vmware driver. It is thus advised to disable
vmport when using a Spice VM. This will permit the Spice client to
switch from absolute to relative pointer, as it may be required for
certain games or applications.
The phyp driver stuffed it into a DomainDefPtr during its attachdevice
routine, but the value is never advertised via capabilities so it should
be safe to drop.
Have the phyp driver use OSTYPE_LINUX, which is what it advertises via
capabilities.
With iothreadid's allowing any 'id' value for an iothread_id, the
iothreadsched code needs a slight adjustment to allow for "any"
unsigned int value in order to create the bitmap of ids that will
have scheduler adjustments. Adjusted the doc description as well.
Remove the iothreadspin array from cputune and replace with a cpumask
to be stored in the iothreadids list.
Adjust the test output because our printing goes in order of the iothreadids
list now.
Adding a new XML element 'iothreadids' in order to allow defining
specific IOThread ID's rather than relying on the algorithm to assign
IOThread ID's starting at 1 and incrementing to iothreads count.
This will allow future patches to be able to add new IOThreads by
a specific iothread_id and of course delete any exisiting IOThread.
Each iothreadids element will have 'n' <iothread> children elements
which will have attribute "id". The "id" will allow for definition
of any "valid" (eg > 0) iothread_id value.
On input, if any <iothreadids> <iothread>'s are provided, they will
be marked so that we only print out what we read in.
On input, if no <iothreadids> are provided, the PostParse code will
self generate a list of ID's starting at 1 and going to the number
of iothreads defined for the domain (just like the current algorithm
numbering scheme). A future patch will rework the existing algorithm
to make use of the iothreadids list.
On output, only print out the <iothreadids> if they were read in.
In a lot places we use path like this:
$(srcdir)/../src/....
when in fact it can be:
$(top_srcdir)/src/
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
If this enviroment variable is set, the virTestCompareToFile helper
will overwrite the file content we are comparing against, if the
file doesn't exist or it doesn't match the expected input.
This is useful when adding new test cases, or making changes that
generate a lot of output churn.
The PortNumber data type is declared to derive from 'short'.
Unfortunately this is an signed type, so validates the range
[-32,768, 32,767] which excludes valid port numbers between
32767 and 65535.
We can't use 'unsignedShort', since we need -1 to be a valid
port number too.
This change is to use 'int' and set an explicit max boundary
instead of relying on the data types' built-in max.
One of the existing tests is changed to use a high port number
to validate the schema.
https://bugzilla.redhat.com/show_bug.cgi?id=1214664
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
According to docs, using 'lun' as a value for device attribute is only valid
with disk types 'block' and 'network'. However current RNG schema also allows
a combination type='file' device='lun' which results in a successfull
xml validation, but fails at qemuBuildCommandLine.
Besides fixing the RNG schema, this patch also adds a qemuxml2argvtest
for this case.
https://bugzilla.redhat.com/show_bug.cgi?id=1210669
The <inbound/> element to <bandwidth/> has several attributes from
which two are mandatory. Well, from two at least one has to be
present: @average or @floor or both. Instead of inventing crazy RNG
schema, let's make all the attributes optional there and rely on our
parsing code to correctly handle the situation.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
On IRC, Hydrar pointed a problem where 'virsh edit' failed on
his domain created through an ISCSI pool managed by virt-manager,
all because the XML included a block device with colons in the
name.
* docs/schemas/basictypes.rng (absFilePath): Add colon as safe.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.xml: New file.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.args: Likewise.
* tests/qemuxml2argvtest.c (mymain): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
When using QEMU's 9pfs the target "dir" element is not necessarily an
absolute path but merely an arbitrary identifier. So validation in that
case currently fails with the misleading
$ virt-xml-validate /tmp/test.xml
Relax-NG validity error : Extra element devices in interleave
/tmp/test.xml:24: element devices: Relax-NG validity error : Element domain failed to validate content
/tmp/test.xml fails to validate
because network address is required by route, so
here we should add one avoid user misunderstand.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
The virNodeDeviceDettach API only works on PCI devices.
Originally added by commit 10d3272e, but the API never
supported USB devices.
Reported by: Martin Polednik <mpolednik@redhat.com>
Commit bab2eda changed the behavior for missing compat attribute,
but failed to update the documentation.
Before, the option was omitted from qemu-img command line and the
qemu-img default was used. Now we always specify the compat value
and the default is 0.10.
Reported by Christophe Fergeau
https://bugzilla.gnome.org/show_bug.cgi?id=746660#c4
This patch adds code that parses and formats configuration for memory
devices.
A simple configuration would be:
<memory model='dimm'>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
</memory>
A complete configuration of a memory device:
<memory model='dimm'>
<source>
<pagesize unit='KiB'>4096</pagesize>
<nodemask>1-3</nodemask>
</source>
<target>
<size unit='KiB'>524287</size>
<node>1</node>
</target>
</memory>
This patch preemptively forbids use of the <memory> device in individual
drivers so the users are warned right away that the device is not
supported.
To enable memory hotplug the maximum memory size and slot count need to
be specified. As qemu supports now other units than mebibytes when
specifying memory, use the new interface in this case.
Add a XML element that will allow to specify maximum supportable memory
and the count of memory slots to use with memory hotplug.
To avoid possible confusion and misuse of the new element this patch
also explicitly forbids the use of the maxMemory setting in individual
drivers's post parse callbacks. This limitation will be lifted when the
support is implemented.
Wikipedia's list of common misspellings [1] has a machine-readable
version. This patch fixes those misspellings mentioned in the list
which don't have multiple right variants (as e.g. "accension", which can
be both "accession" and "ascension"), such misspellings are left
untouched. The list of changes was manually re-checked for false
positives.
[1] https://en.wikipedia.org/wiki/Wikipedia:Lists_of_common_misspellings/For_machines
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
I spent quite some time figuring that backingStore info
isn't included in the dom xml, unless guest is up and
running. Hopefully putting that in the doc should help.
Also, several people have complained that libvirt reports
a backing file as raw, even though they expected it to be
qcow2; where the culprit is usually the user forgetting to
create the file with qemu-img create -o backing_fmt=qcow2.
This patch adds that info to the doc.
Signed-off-by: Deepak C Shetty <deepakcs@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Midonet is an opensource virtual networking that over lays the IP
network between hypervisors. Currently, such networks can be made
with the openvswitch virtualport type.
This patch, defines the schema and documentation that will serve
as basis for the follow up patches that will add support to libvirt
for using Midonet virtual ports for its interfaces. The schema
definition requires that the port profile expresses its interfaceid
as part of the port profile. For that reason, this is part of the
patch too.
Signed-off-by: Antoni Segura Puimedon <toni+libvirt@midokura.com>
We're parsing memballoon status period as unsigned int, but when we're
trying to set it, both we and qemu use signed int. That means large
values will get wrapped around to negative one resulting in error.
Basically the same problem as commit e3a7b874 was dealing with when
updating live domain.
QEMU changed the accepted value to int64 in commit 1f9296b5, but even
values as INT_MAX don't make sense since the value passed means seconds.
Hence adding capability flag for this change isn't worth it.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1140958
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
All the devices we have format their address as its last sub-element, so
let's change memballoon to follow suit. Also adjust RNG to allow any
order of them so 'virsh edit' doesn't shout at us.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Now that the size of guest's memory can be inferred from the NUMA
configuration (if present) make it optional to specify <memory>
explicitly.
To make sure that memory is specified add a check that some form of
memory size was specified. One side effect of this change is that it is
no longer possible to specify 0KiB as memory size for the VM, but I
don't think it would be any useful to do so. (I can imagine embedded
systems without memory, just registers, but that's far from what libvirt
is usually doing).
Forbidding 0 memory for guests also fixes a few corner cases where 0 was
not interpreted correctly and caused failures. (Arguments for numad when
using automatic placement, size of the balloon). This fixes problems
described in https://bugzilla.redhat.com/show_bug.cgi?id=1161461
Test case changes are added to verify that the schema change and code
behave correctly.
The version attribute in redirdev filters refers to the revision
of the device, not the version of the USB protocol.
Explicitly state that this is not the USB protocol and remove references
to those round version numbers that resemble USB protocol versions.
https://bugzilla.redhat.com/show_bug.cgi?id=1177237
Our code supports that for ages. When using a <filterref/> to an
<interface/> several parameters can be passed to the filter. Later,
when building firewall rules, parameters are substituted for their
values. However, our RNG schema allowed only one parameter to be
passed.
Reported-by: Brian Rak <brak@gameservers.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
To prevent a confusion about missing chardev argument in qemu
command line add a note about that behavior into documentation.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1129198
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
There was a mess in the way how we store unlimited value for memory
limits and how we handled values provided by user. Internally there
were two possible ways how to store unlimited value: as 0 value or as
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED. Because we chose to store memory
limits as unsigned long long, we cannot use -1 to represent unlimited.
It's much easier for us to say that everything greater than
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED means unlimited and leave 0 as valid
value despite that it makes no sense to set limit to 0.
Remove unnecessary function virCompareLimitUlong. The update of test
is to prevent the 0 to be miss-used as unlimited in future.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1146539
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Adding functionality to libvirt that will allow it
query the ethtool interface for the availability
of certain NIC HW offload features
Here is an example of the feature XML definition:
<device>
<name>net_eth4_90_e2_ba_5e_a5_45</name>
<path>/sys/devices/pci0000:00/0000:00:03.0/0000:08:00.1/net/eth4</path>
<parent>pci_0000_08_00_1</parent>
<capability type='net'>
<interface>eth4</interface>
<address>90:e2:ba:5e:a5:45</address>
<link speed='10000' state='up'/>
<feature name='rx'/>
<feature name='tx'/>
<feature name='sg'/>
<feature name='tso'/>
<feature name='gso'/>
<feature name='gro'/>
<feature name='rxvlan'/>
<feature name='txvlan'/>
<feature name='rxhash'/>
<capability type='80203'/>
</capability>
</device>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
In commit edd1295e1d I've introduced an
XML element that allows to configure state of the network interface
link. Somehow the RNG schema hunk ended up in a weird place in the
network schema definition. Move it to the right place and add a test
case.
Note that the link state is set up via the monitor at VM startup so I
originally didn't think of adding a test case.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1173468
https://bugzilla.redhat.com/show_bug.cgi?id=1181062
According to the formatstorage.html description for <source> element
and "format" attribute: "All drivers are required to have a default
value for this, so it is optional."
As it turns out the disk backend did not choose a default value, so I
added a default of "msdos" if the source type is "unknown" as well as
updating the storage.html backend disk volume driver documentation to
indicate the default format is dos.
Our documentation isn't 100% clear about hostdev 'managed' attribute usage,
because it only makes sense to use it with PCI devices, yet we format
this attribute to all hostdev devices. By adding a note into the docs,
we can possibly avoid confusion from customer's side and also avoid a solution
using ternary logic.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1155887
As reported on the libvirt-users list [1], there's new web
application called mist.io which uses libvirt as one of its
backends. Lets add it into our list of libivrt based
applications.
1: https://www.redhat.com/archives/libvirt-users/2015-February/msg00096.html
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The element wasn't declared under the interleave thus it was required
always to be first. This made it inconvenient when pasting new stuff to
the XML manually in the "wrong" place.
The "virtio-mmio" is perfectly valid address type which we parse and
format correctly, but it's missing in our RNG schemas, hence editing a
domain with device having such address fails the validation.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
At least Xen supports backend drivers in another domain (aka "driver
domain"). This patch introduces an XML config option for specifying the
backend domain name for <disk> and <interface> devices. E.g.
<disk>
<backenddomain name='diskvm'/>
...
</disk>
<interface type='bridge'>
<backenddomain name='netvm'/>
...
</interface>
In the future, same option will be needed for USB devices (hostdev
objects), but for now libxl doesn't have support for PVUSB.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
In preparation for adding docs about virtlockd, split out
the sanlock setup docs into a separate page.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Add an XML attribute to allow disabling merge of rx buffers
on the host:
<interface ...>
...
<model type='virtio'/>
<driver ...>
<host mrg_rxbuf='off'/>
</driver>
</interface>
https://bugzilla.redhat.com/show_bug.cgi?id=1186886
In order for QEMU vCPU (and other) threads to run with RT scheduler,
libvirt needs to take care of that so QEMU doesn't have to run privileged.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178986
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
In our RNG schema we do allow multiple (different) seclabels per-domain,
but don't allow this for devices, yet we neither have a check in our XML parser,
nor in a post-parse callback. In that case we should allow multiple
(different) seclabels for devices as well.
Change the wording in the device-address-part of the docmunentation since
the ccw bus address support added to the optional address parameter of
virsh attach-disk for S390.
Signed-off-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
It is only usable for NETWORK and BRIDGE type interfaces.
Error out when trying to start a domain where the custom
tap device path is specified for interfaces of other types,
or when the daemon is not privileged.
Note that this cannot be checked at definition time, because
the comparison is against actual type.
https://bugzilla.redhat.com/show_bug.cgi?id=1147195
It is only supported for virtio adapters.
Silently drop it if it was specified for other models,
as is done for other virtio attributes.
Also mention this in the documentation.
https://bugzilla.redhat.com/show_bug.cgi?id=1147195
https://bugzilla.redhat.com/show_bug.cgi?id=1170492
In one of our previous commits (dc8b7ce7) we've done a functional
change even though it was intended as pure refactor. The problem is,
that the following XML:
<vcpu placement='static' current='2'>6</vcpu>
<cputune>
<emulatorpin cpuset='1-3'/>
</cputune>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
gets translated into this one:
<vcpu placement='auto' current='2'>6</vcpu>
<cputune>
<emulatorpin cpuset='1-3'/>
</cputune>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
We should not change the vcpu placement mode. Moreover, we're doing
something similar in case of emulatorpin and iothreadpin. If they were
set, but vcpu placement was auto, we've mistakenly removed them from
the domain XML even though we are able to set them independently on
vcpus.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There are some interface types (notably 'server' and 'client')
which instead of allowing the default set of elements and
attributes (like the rest do), try to enumerate only the elements
they know of. This way it's, however, easy to miss something. For
instance, the <address/> element was not mentioned at all. This
resulted in a strange behavior: when such interface was added
into XML, the address was automatically generated by parsing
code. Later, the formatted XML hasn't passed the RNG schema. This
became more visible once we've turned on the XML validation on
domain XML changes: appending an empty line at the end of
formatted XML (to trick virsh think the XML had changed) made
libvirt to refuse the very same XML it formatted.
Instead of trying to find each element and attribute we are
missing in the schema, lets just allow all the elements and
attributes like we're doing that for the rest of types. It's no
harm if the schema is wider than our parser allows.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1138516
If the provided volume name doesn't match what parted generated as the
partition name, then return a failure.
Update virsh.pod and formatstorage.html.in to describe the 'name' restriction
for disk pools as well as the usage of the <target>'s <format type='value'>.
https://bugzilla.redhat.com/show_bug.cgi?id=1130390
The listen address is not mandatory for <interface type='server'>
but when it's not specified, we've been formatting it as:
-netdev socket,listen=(null):5558,id=hostnet0
which failed with:
Device 'socket' could not be initialized
Omit the address completely and only format the port in the listen
attribute.
Also fix the schema to allow specifying a model.
This adds a new "localOnly" attribute on the domain element of the
network xml. With this set to "yes", DNS requests under that domain
will only be resolved by libvirt's dnsmasq, never forwarded upstream.
This was how it worked before commit f69a6b987d, and I found that
functionality useful. For example, I have my host's NetworkManager
dnsmasq configured to forward that domain to libvirt's dnsmasq, so I can
easily resolve guest names from outside. But if libvirt's dnsmasq
doesn't know a name and forwards it to the host, I'd get an endless
forwarding loop. Now I can set localOnly="yes" to prevent the loop.
Signed-off-by: Josh Stone <jistone@redhat.com>
Since the day we removed python bindings from the core repository, the
documentation was missing that information.
Reported-by: Lingyu Zhu <lynuszhu@gmail.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Ploop is a pseudo device which makeit possible to access
to an image in a file as a block device. Like loop devices,
but with additional features, like snapshots, write tracker
and without double-caching.
It used in PCS for containers and in OpenVZ. You can manage
ploop devices and images with ploop utility
(http://git.openvz.org/?p=ploop).
Signed-off-by: Dmitry Guryanov <dguryanov@parallels.com>
Well, since the link to the virConnectGetDomainCapabilities API is in
<pre/> section we must take special care about the spaces around the
link.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
QEMU supports feature specification with -cpu host and we just skip
using that. Since QEMU developers themselves would like to use this
feature, this patch modifies the code to work.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178850
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
It was brought to my attention that some -boot options may not
work with UEFI. For instance, rebootTimeout is very SeaBIOS
specific,splash logo is not implemented yet on OVMF, and so on.
We should document this limitation at least.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Make use of the ebtables functionality to be able to filter certain
parameters of icmpv6 packets. Extend the XML parser for icmpv6 types,
type ranges, codes, and code ranges. Extend the nwfilter documentation,
schema, and test cases.
Being able to filter icmpv6 types and codes helps extending the DHCP
snooper for IPv6 and filtering at least some parameters of IPv6's NDP
(Neighbor Discovery Protocol) packets. However, the filtering will not
be as good as the filtering of ARP packets since we cannot
check on IP addresses in the payload of the NDP packets.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Add the possibility to have more than one IP address configured for a
domain network interface. IP addresses can also have a prefix to define
the corresponding netmask.
Volume and pool formatting functions took different approaches to
unspecified uids/gids. When unknown, it is always parsed as -1, but one
of the functions formatted it as unsigned int (wrong) and one as
int (better). Due to that, our two of our XML files from tests cannot
be parsed on 32-bit machines.
RNG schema needs to be modified as well, but because both
storagepool.rng and storagevol.rng need same schema for permission
element, save some space by moving it to storagecommon.rng.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The macTableManager attribute of a network's bridge subelement tells
libvirt how the bridge's MAC address table (used to determine the
egress port for packets) is managed. In the default mode, "kernel",
management is left to the kernel, which usually determines entries in
part by turning on promiscuous mode on all ports of the bridge,
flooding packets to all ports when the correct destination is unknown,
and adding/removing entries to the fdb as it sees incoming traffic
from particular MAC addresses. In "libvirt" mode, libvirt turns off
learning and flooding on all the bridge ports connected to guest
domain interfaces, and adds/removes entries according to the MAC
addresses in the domain interface configurations. A side effect of
turning off learning and unicast_flood on the ports of a bridge is
that (with Linux kernel 3.17 and newer), the kernel can automatically
turn off promiscuous mode on one or more of the bridge's ports
(usually only the one interface that is used to connect the bridge to
the physical network). The result is better performance (because
packets aren't being flooded to all ports, and can be dropped earlier
when they are of no interest) and slightly better security (a guest
can still send out packets with a spoofed source MAC address, but will
only receive traffic intended for the guest interface's configured MAC
address).
The attribute looks like this in the configuration:
<network>
<name>test</name>
<bridge name='br0' macTableManager='libvirt'/>
...
This patch only adds the config knob, documentation, and test
cases. The functionality behind this knob is added in later patches.
Fix format of the secret XML in the example. The XML had an extraneous
"type='iscsi'" (which is used by the <disk> definitions)
The world wide node name had a typo in the acronym (wwwn).
The apibuild.py script did not handle whitespace in preprocessor
macros, so it failed to detect constants declared with '# define'
instead of '#define'. Since we now correctly indent our public
header files, we have silently lost all constants from
libvirt-api.xml. This also caused us to not detect formatting
errors in constant docs
This changes the display from:
libvirt-storage: APIs for management of storages
to
libvirt-storage: APIs for management of storage pools and volumes
In making that change I expected my build tree html output to be
regenerated; however, it wasn't because the dependency for the separated
libvirt-storage.h wasn't there. It was only present for libvirt.h.in
So I added each in the order displayed on the docs/html/index.html page
Make was not able to realize the dependencies for html/*.html files when
running 'make -j9 dist'. All the files are generated together with
html/index.html, so simply separating them into another variable and
adding one block into the dependency chain solves the issue.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Since libvirt.h was split into multiple files and similarly
docs/libvirt-libvirt.html, docs/hvsupport.html have bad hyperlinks. The
same happens for all the html.in files that used <code class='docref'>
tag, because page.xsl has no idea where to point the link that's found.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1159180
The virStoragePoolSourceFindDuplicate only checks the incoming definition
against the same type of pool as the def; however, for "scsi_host" and
"fc_host" adapter pools, it's possible that either some pool "scsi_host"
adapter definition is already using the scsi_hostN that the "fc_host"
adapter definition wants to use or some "fc_host" pool adapter definition
is using a vHBA scsi_hostN or parent scsi_hostN that an incoming "scsi_host"
definition is trying to use.
This patch adds the mismatched type checks and adds extraneous comments
to describe what each check is determining.
This patch also modifies the documentation to be describe what scsi_hostN
devices a "scsi_host" source adapter should use and which to avoid. It also
updates the parent definition to specifically call out that for mixed
environments it's better to define which parent to use so that the duplicate
pool checks can be done properly.
Add attribute to set vgamem_mb parameter of QXL device for QEMU. This
value sets the size of VGA framebuffer for QXL device. Default value in
QEMU is 8MB so reuse it also in libvirt to not break things.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The vram attribute was introduced to set the video memory but it is
usable only for few hypervisors excluding QEMU/KVM and the old XEN
driver. Only in case of QEMU the vram was used for QXL.
This patch updates the documentation to reflect current code in libvirt
and also changes the cases when we will set the default vram attribute.
It also fixes existing strange default value for VGA devices 9MB to 16MB
because the video ram should be rounded to power of two.
The change of default value could affect migrations but I found out that
QEMU always round the video ram to power of two internally so it's safe
to change the default value to the next closest power of two and also
silently correct every domain XML definition. And it's also safe because
we don't pass the value to QEMU.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
To be able to express some use cases of the RBD backing with libvirt, we
need to be able to specify a config file for the RBD client to qemu as
that is one of the commonly used options.
Some storage systems have internal support for snapshots. Libvirt should
be able to select a correct snapshot when starting a VM.
This patch adds a XML element to select a storage source snapshot for
the RBD protocol which supports this feature.
The docs describing the <host> element that are under the <source>
element in the XML document were incorrectly placed under the <disk>
element. Move them to the correct place.
To track state of virtio channels this patch adds a new output-only
attribute called 'state' to the <target> element of virtio channels.
This will be later populated with the guest state of the channel.
Since 1.2.8 it's possible to use OVMF on domains. Moreover, it's
possible to have libvirt create NVRAM file per domain. Later,
when domain is undefined, the file is removed too. However,
things are a bit complicated when domain's transient. There's no
undefine to transient domains. There are two options: 1) leave
the file behind and let mgmt app remove it. 2) remove it
automatically as domain dies.
But, in some scenarios mgmt app may want to preserve the file,
copy it somewhere safe, and then copy it back when the domain is
starting again. And this wouldn't be possible with case 2). So,
even though case 1) leaves some files behind (possibly undeleted
for a long time), the files themselves are small (128K each). And
data loss is worse than full disk, isn't it?
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
After recent discussion it looks like curly brackets around one-line
bodies are preferred if the preceding condition is, itself, multiline.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Rather than just picking the first CD (or failing that, HDD) we come
across, if the user has picked a boot device ordering with <boot
order=''>, respect that (and just try to boot the lowest-index device).
Adds two sets of tests to bhyve2xmlargv; 'grub-bootorder' shows that we
pick a user-specified device over the first device in the domain;
'grub-bootorder2' shows that we pick the first (lowest index) device.
The API docs generators were broken by the header file
re-organization. Specifically
* html/libvirt-libvirt.html was empty (and should be deleted)
* Makefile.am didn't install html/libvirt-libvirt-*.html
* hvsupport.html was mostly empty
* sitemap.html.in didn't list the new html/*.html files
https://bugzilla.redhat.com/show_bug.cgi?id=1160926
Introduce a 'managed' attribute to allow libvirt to decide whether to
delete a vHBA vport created via external means such as nodedev-create.
The code currently decides whether to delete the vHBA based solely on
whether the parent was provided at creation time. However, that may not
be the desired action, so rather than delete and force someone to create
another vHBA via an additional nodedev-create allow the configuration of
the storage pool to decide the desired action.
During createVport when libvirt does the VPORT_CREATE, set the managed
value to YES if not already set to indicate to the deleteVport code that
it should delete the vHBA when the pool is destroyed.
If libvirtd is restarted all the memory only state was lost, so for a
persistent storage pool, use the virStoragePoolSaveConfig in order to
write out the managed value.
Because we're now saving the current configuration, we need to be sure
to not save the parent in the output XML if it was undefined at start.
Saving the name would cause future starts to always use the same parent
which is not the expected result when not providing a parent. By not
providing a parent, libvirt is expected to find the best available
vHBA port for each subsequent (re)start.
At deleteVport, use the new managed value to decide whether to execute
the VPORT_DELETE. Since we no longer save the parent in memory or in
XML when provided, if it was not provided, then we have to look it up.
https://bugzilla.redhat.com/show_bug.cgi?id=1160565
The existing code assumed that the configuration of a 'parent' attribute
was correct for the createVport path. As it turns out, that may not be
the case which leads errors during the deleteVport path because the
wwnn/wwpn isn't associated with the parent.
With this change the following is reported:
error: Failed to start pool fc_pool_host3
error: XML error: Parent attribute 'scsi_host4' does not match parent 'scsi_host3' determined for the 'scsi_host16' wwnn/wwpn lookup.
for XML as follows:
<pool type='scsi'>
<name>fc_pool</name>
<source>
<adapter type='fc_host' parent='scsi_host4' wwnn='5001a4aaf3ca174b' wwpn='5001a4a77192b864'/>
</source>
Where 'nodedev-dumpxml scsi_host16' provides:
<device>
<name>scsi_host16</name>
<path>/sys/devices/pci0000:00/0000:00:04.0/0000:10:00.0/host3/vport-3:0-11/host16</path>
<parent>scsi_host3</parent>
<capability type='scsi_host'>
<host>16</host>
<unique_id>13</unique_id>
<capability type='fc_host'>
<wwnn>5001a4aaf3ca174b</wwnn>
<wwpn>5001a4a77192b864</wwpn>
...
The patch also adjusts the description of the storage pool to describe the
restrictions.
Signed-off-by: John Ferlan <jferlan@redhat.com>
We still default to bhyveloader(1) if no explicit bootloader
configuration is supplied in the domain.
If the /domain/bootloader looks like grub-bhyve and the user doesn't
supply /domain/bootloader_args, we make an intelligent guess and try
chainloading the first partition on the disk (or a CD if one exists,
under the assumption that for a VM a CD is likely an install source).
Caveat: Assumes the HDD boots from the msdos1 partition. I think this is
a pretty reasonable assumption for a VM. (DrvBhyve with Bhyveload
already assumes that the first disk should be booted.)
I've tested both HDD and CD boot and they seem to work.
Modify the structure _virDomainBlockIoTuneInfo to support these the new
options.
Change the initialization of the variable expectedInfo in qemumonitorjsontest.c
to avoid compiling problem.
Add documentation about the new xml options
Signed-off-by: Matthias Gatto <matthias.gatto@outscale.com>
CPU numa topology implicitly allows memory specification in 'KiB'.
Enabling this to accept the 'unit' in which memory needs to be specified.
This now allows users to specify memory in units of choice, and
lists the same in 'KiB' -- just like other 'memory' elements in XML.
<numa>
<cell cpus='0-3' memory='1024' unit='MiB' />
<cell cpus='4-7' memory='1024' unit='MiB' />
</numa>
Also augment test cases to correctly model NUMA memory specification.
This adds the tag 'unit="KiB"' for memory attribute in NUMA cells.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As documented in https://bugzilla.redhat.com/show_bug.cgi?id=1161358,
the ACL attribute should be named: interface_macaddr
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Add documentation to explain how compat-mode can be invoked with libvirt
running on PowerPC architecture.
It also mentions that this change is available libvirt 1.2.11 onwards.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Extending the iothread disk support from pci to pci and ccw.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Create a new libvirt-host.h file to hold the public
API definitions for the virConnect type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-domain.h file to hold the public
API definitions for the virDomain type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-event.h file to hold the public
API definitions for the virEvent type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-storage.h file to hold the public
API definitions for the virStorage/Vol type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-stream.h file to hold the public
API definitions for the virStream type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Note the definition of virStreamPtr is not moved, since that
must be declared early for all other libvirt APIs to be able
to reference it.
Create a new libvirt-secret.h file to hold the public
API definitions for the virSecret type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-nodedev.h file to hold the public
API definitions for the virNodeDevice type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-nwfilter.h file to hold the public
API definitions for the virNWFilter type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-interface.h file to hold the public
API definitions for the virInterface type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-network.h file to hold the public
API definitions for the virNetwork type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
Create a new libvirt-domain-snapshot.h file to hold the public
API definitions for the virDomainSnapshot type. This header
file is not self-contained, so applications will not directly
include it. They will continue to #include <libvirt/libvirt.h>
The virTypedParameterValidateSet method will need to be used
from several libvirt-*.c files so must be non-static
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
To prepare for introducing a single global driver, rename the
virDriver struct to virHypervisorDriver and the registration
API to virRegisterHypervisorDriver()
These tools have been rewritten upstream, so you don't need to link to
the old tools, link to the new ones and mention they are part of
libguestfs.
Also remove the link to "Poor man's P2V". There's no real reason to
use that technique any longer since the rewritten tools are simple,
fast and highly capable.
This new attribute will control whether or not libvirt will pay
attention to guest notifications about changes to network device mac
addresses and receive filters. The default for this is 'no' (for
security reasons). If it is set to 'yes' *and* the specified device
model and connection support it (currently only macvtap+virtio) then
libvirt will watch for NIC_RX_FILTER_CHANGED events, and when it
receives one, it will issue a query-rx-filter command, retrieve the
result, and modify the host-side macvtap interface's mac address and
unicast/multicast filters accordingly.
The functionality behind this attribute will be in a later patch. This
patch merely adds the attribute to the top-level of a domain's
<interface> as well as to <network> and <portgroup>, and adds
documentation and schema/xml2xml tests. Rather than adding even more
test files, I've just added the net attribute in various applicable
places of existing test files.
This patch adds parsing/formatting code as well as documentation for
shared memory devices. This will currently be only accessible in QEMU
using it's ivshmem device, but is designed as generic as possible to
allow future expansion for other hypervisors.
In the devices section in the domain XML users may specify:
- For shmem device using a server:
<shmem name='shmem0'>
<server path='/tmp/socket-ivshmem0'/>
<size unit='M'>32</size>
<msi vectors='32' ioeventfd='on'/>
</shmem>
- For ivshmem device not using an ivshmem server:
<shmem name='shmem1'>
<size unit='M'>32</size>
</shmem>
Most of the configuration is made optional so it also allows
specifications like:
<shmem name='shmem1/>
<shmem name='shmem2'>
<server/>
</shmem>
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
According to our documentation logical pool supports formats 'auto' and
'lvm2'. However, in storage_conf.c we previously defined storage pool
formats: unknown, lvm2. Due to backward compatibility reasons
we must continue refer to pool format type 'unknown' instead of 'auto'.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1123767
Add options for tuning segment offloading:
<driver>
<host csum='off' gso='off' tso4='off' tso6='off'
ecn='off' ufo='off'/>
<guest csum='off' tso4='off' tso6='off' ecn='off' ufo='off'/>
</driver>
which control the respective host_ and guest_ properties
of the virtio-net device.
For the tap backend the default is specified and the same should be
done for the vhost attribute.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
- docs/formatstorage.html.in: document 'zfs' pool type, add it
to a list of pool types that could use source physical devices
- docs/storage.html.in: update a ZFS pool example XML with
source physical devices, mention that starting from 1.2.9 a
pool could be created from this devices by libvirt and in earlier
versions user still has to create a pool manually
- docs/drvbhyve.html.in: add an example with ZFS pools
- Provide an implementation for buildPool and deletePool operations
for the ZFS storage backend.
- Add VIR_STORAGE_POOL_SOURCE_DEVICE flag to ZFS pool poolOptions
as now we can specify devices to build pool from
- storagepool.rng: add an optional 'sourceinfodev' to 'sourcezfs' and
add an optional 'target' to 'poolzfs' entity
- Add a couple of tests to storagepoolxml2xmltest
Check to see if the UEFI binary mentioned in qemu.conf actually
exists, and if so expose it in domcapabilities like
<loader ...>
<value>/path/to/ovmf</value>
</loader>
We introduce some generic domcaps infrastructure for handling
a dynamic list of string values, it may be of use for future bits.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of 542899168c we learned libvirt to use UEFI for domains.
However, management applications may firstly query if libvirt
supports it. And this is where virConnectGetDomainCapabilities()
API comes handy.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
For tuning the network, alternative devices
for creating tap and vhost devices can be specified via:
<backend tap='/dev/net/tun' vhost='/dev/net-vhost'/>
I noticed this with the recent iothread pinning code, but the
problem existed longer than that. The XML validation required
users to supply <cputune> children in a strict order, even though
there was no conceptual reason why they can't occur in any order.
docs/ changes best viewed with -w
* docs/schemas/domaincommon.rng (cputune): Add interleave.
* tests/qemuxml2argvdata/qemuxml2argv-cputune-iothreads.xml: Swap
up order, copying canonical form...
* tests/qemuxml2xmloutdata/qemuxml2xmlout-cputune-iothreads.xml:
...here.
* tests/qemuxml2xmltest.c (mymain): Mark the difference.
Signed-off-by: Eric Blake <eblake@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1101574
Add an option 'iothreadpin' to the <cpuset> to allow for setting the
CPU affinity for each IOThread.
The iothreadspin will mimic the vcpupin with respect to being able to
assign each iothread to a specific CPU, although iothreads ids start
at 1 while vcpu ids start at 0. This matches the iothread naming scheme.
When spanning tree protocol is allowed in bridge settings, forward delay
value is set as well (default is 0 if omitted). Until now, there was no
check for delay value validity. Delay makes sense only as a positive
numerical value.
Note: However, even if you provide positive numerical value, brctl
utility only uses values from range <2,30>, so the number provided can
be modified (kernel most likely) to fall within this range.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1125764
At the beginning when I was inventing <loader/> attributes and
<nvram/> I've introduced this @readonly attribute to the loader
element. It accepted values 'on' and 'off'. However, later, during the
review process, that has changed to 'yes' and 'no', but the example
XML snippet wasn't updated, so while the description is correct, the
example isn't.
Reported-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When using split UEFI image, it may come handy if libvirt manages per
domain _VARS file automatically. While the _CODE file is RO and can be
shared among multiple domains, you certainly don't want to do that on
the _VARS file. This latter one needs to be per domain. So at the
domain startup process, if it's determined that domain needs _VARS
file it's copied from this master _VARS file. The location of the
master file is configurable in qemu.conf.
Temporary, on per domain basis the location of master NVRAM file can
be overridden by this @template attribute I'm inventing to the
<nvram/> element. All it does is holding path to the master NVRAM file
from which local copy is created. If that's the case, the map in
qemu.conf is not consulted.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Up to now, users can configure BIOS via the <loader/> element. With
the upcoming implementation of UEFI this is not enough as BIOS and
UEFI are conceptually different. For instance, while BIOS is ROM, UEFI
is programmable flash (although all writes to code section are
denied). Therefore we need new attribute @type which will
differentiate the two. Then, new attribute @readonly is introduced to
reflect the fact that some images are RO.
Moreover, the OVMF (which is going to be used mostly), works in two
modes:
1) Code and UEFI variable store is mixed in one file.
2) Code and UEFI variable store is separated in two files
The latter has advantage of updating the UEFI code without losing the
configuration. However, in order to represent the latter case we need
yet another XML element: <nvram/>. Currently, it has no additional
attributes, it's just a bare element containing path to the variable
store file.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Now that hanging brace offenders have been fixed, we can automate
the check, and document our style. Done as a separate commit from
code changes, to make it easier to just backport code changes, if
that is ever needed.
* cfg.mk (sc_curly_braces_style): Catch hanging braces.
* docs/hacking.html.in: Document it.
* HACKING: Regenerate.
Signed-off-by: Eric Blake <eblake@redhat.com>
Add a new disk "driver" attribute "iothread" to be parsed as the thread
number for the disk to use. In order to more easily facilitate the usage
and configuration of the iothread, a "zero" for the attribute indicates
iothreads are not supported for the device and a positive value indicates
the specific thread to try and use.
Introduce XML to allowing adding iothreads to the domain. These can be
used by virtio-blk-pci devices in order to assign a specific thread to
handle the workload for the device. The iothreads are the official
implementation of the virtio-blk Data Plane that's been in tech preview
for QEMU.
QEMU 2.1 added support for the kvm=off option to the -cpu command,
allowing the KVM hypervisor signature to be hidden from the guest.
This enables disabling of some paravirualization features in the
guest as well as allowing certain drivers which test for the
hypervisor to load. Domain XML syntax is as follows:
<domain type='kvm>
...
<features>
...
<kvm>
<hidden state='on'/>
</kvm>
</features>
...
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The 'min_guarantee' is used by VMware ESX and OpenVZ drivers,
with qemu however, libvirt should report error when starting a domain,
because this element is not used.
Resolves https://bugzilla.redhat.com/show_bug.cgi?id=1122455
On some places in the libvirt code we have:
f(a,z)
instead of
f(a, z)
This trivial patch fixes couple of such occurrences.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since vbox driver rewrite the virDriver structure init moved from
vbox_tmpl.c into vbox_common.c. However, our hvsupport.pl script
doesn't count with that. It still parses vbox_tmp.c and looks for
virDriver structure which is not found there anymore. As a result,
at hvsupport page is seems like vbox driver doesn't support
anything.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The correct vlanid range is 0~4095.
After merging this patch, we can not validate a interface xml with vlanid >= 4096.
[root@localhost ~]# cat vlan.xml
<interface type='vlan' name='eno1.4096'>
<start mode='onboot'/>
<protocol family='ipv4'>
<dhcp/>
</protocol>
<vlan tag='4096'>
<interface name='eno1'/>
</vlan>
</interface>
[root@localhost ~]# virt-xml-validate vlan.xml
vlan.xml:1: element interface: Relax-NG validity error : Invalid sequence in interleave
vlan.xml:6: element vlan: Relax-NG validity error : Element interface failed to validate content
vlan.xml:6: element vlan: Relax-NG validity error : Element vlan failed to validate attributes
vlan.xml fails to validate
[root@localhost ~]#
Here is a ip command help on this.
[root@localhost /]# ip link add link eno1 name eno1.90 type vlan help
Usage: ... vlan [ protocol VLANPROTO ] id VLANID [ FLAG-LIST ]
[ ingress-qos-map QOS-MAP ] [ egress-qos-map QOS-MAP ]
VLANPROTO: [ 802.1Q / 802.1ad ]
VLANID := 0-4095
FLAG-LIST := [ FLAG-LIST ] FLAG
FLAG := [ reorder_hdr { on | off } ] [ gvrp { on | off } ] [ mvrp { on | off } ]
[ loose_binding { on | off } ]
QOS-MAP := [ QOS-MAP ] QOS-MAPPING
QOS-MAPPING := FROM:TO
Implement ZFS storage backend driver. Currently supported
only on FreeBSD because of ZFS limitations on Linux.
Features supported:
- pool-start, pool-stop
- pool-info
- vol-list
- vol-create / vol-delete
Pool definition looks like that:
<pool type='zfs'>
<name>myzfspool</name>
<source>
<name>actualpoolname</name>
</source>
</pool>
The 'actualpoolname' value is a name of the pool on the system,
such as shown by 'zpool list' command. Target makes no sense
here because volumes path is always /dev/zvol/$poolname/$volname.
User has to create a pool on his own, this driver doesn't
support pool creation currently.
A volume could be used with Qemu by adding an entry like this:
<disk type='volume' device='disk'>
<driver name='qemu' type='raw'/>
<source pool='myzfspool' volume='vol5'/>
<target dev='hdc' bus='ide'/>
</disk>
Commit 4cf53158 tried to set up unique labels per disk in the
example, but ended up choosing strings that don't correspond
to the usual choice of bus types. Tweak the strings once again.
* docs/formatdomain.html.in: Use preferred names.
Signed-off-by: Eric Blake <eblake@redhat.com>
Introduce a new structure to handle an iSCSI host device based on the
existing virDomainHostdevSubsysSCSI by adding a "protocol='iscsi'" to
the <source/> element. The existing scsi_host subsystem RNG was modified
to read an optional "protocol='adapter'", although it won't be written
out nor is it documented as an option (by choice).
The new hostdev structure mimics the existing <disk/> element for an
iSCSI device (network) device. New XML is:
<hostdev mode='subsystem' type='scsi' managed='yes'>
<source protocol='iscsi' name='iqn.1992-01.com.example'>
<host name='example.org' port='3260'/>
<auth username='myname'>
<secret type='iscsi' usage='mycluster_myname'/>
</auth>
</source>
<address type='drive' controller='0' bus='0' target='2' unit='5'/>
</hostdev>
The controller element will mimic the existing scsi_host code insomuch
as when 'lsi' and 'virtio-scsi' are used.
Jiri Moskovcak reported on IRC that the documentation on valid
<disk> was confusing because it didn't have unique dev='...'
entries.
* docs/formatdomain.html.in: Use unique names.
Signed-off-by: Eric Blake <eblake@redhat.com>
A future patch is going to wire up qemu active block commit jobs;
but as they have similar events and are canceled/pivoted in the
same way as block copy jobs, it is easiest to track all bookkeeping
for the commit job by reusing the <mirror> element. This patch
adds domain XML to track which job was responsible for creating a
mirroring situation, and adds a job='copy' attribute to all
existing uses of <mirror>. Along the way, it also massages the
qemu monitor backend to read the new field in order to generate
the correct type of libvirt job (even though it requires a
future patch to actually cause a qemu event that can be reported
as an active commit). It also prepares to update persistent XML
to match changes made to live XML when a copy completes.
* docs/schemas/domaincommon.rng: Enhance schema.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.h (_virDomainDiskDef): Add a field.
* src/conf/domain_conf.c (virDomainBlockJobType): String conversion.
(virDomainDiskDefParseXML): Parse job type.
(virDomainDiskDefFormat): Output job type.
* src/qemu/qemu_process.c (qemuProcessHandleBlockJob): Distinguish
active from regular commit.
* src/qemu/qemu_driver.c (qemuDomainBlockCopy): Set job type.
(qemuDomainBlockPivot, qemuDomainBlockJobImpl): Clean up job type
on completion.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-mirror-old.xml:
Update tests.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-disk-active-commit.xml: New
file.
* tests/qemuxml2xmltest.c (mymain): Drive new test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Doing a blockcopy operation across a libvirtd restart is not very
robust at the moment. In particular, we are clearing the <mirror>
element prior to telling qemu to finish the job. Also, thanks to the
ability to request async completion, the user can easily regain
control prior to qemu actually finishing the effort, and they should
be able to poll the domain XML to see if the job is still going.
A future patch will fix things to actually wait until qemu is done
before modifying the XML to reflect the job completion. But since
qemu issues identical BLOCK_JOB_COMPLETE events regardless of whether
the job was cancelled (kept the original disk) or completed (pivoted
to the new disk), we have to track which of the two operations were
used to end the job. Furthermore, we'd like to avoid attempts to
end a job where we are already waiting on an earlier request to qemu
to end the job. Likewise, if we miss the qemu event (perhaps because
it arrived during a libvirtd restart), we still need enough state
recorded to be able to determine how to modify the domain XML once
we reconnect to qemu and manually learn whether the job still exists.
Although this patch doesn't actually fix the problem, it is a
preliminary step that makes it possible to track whether a job
has already begun steps towards completion.
* src/conf/domain_conf.h (virDomainDiskMirrorState): New enum.
(_virDomainDiskDef): Convert bool mirroring to new enum.
* src/conf/domain_conf.c (virDomainDiskDefParseXML)
(virDomainDiskDefFormat): Handle new values.
* src/qemu/qemu_process.c (qemuProcessHandleBlockJob): Adjust
client.
* src/qemu/qemu_driver.c (qemuDomainBlockPivot)
(qemuDomainBlockJobImpl): Likewise.
* docs/schemas/domaincommon.rng (diskMirror): Expose new values.
* docs/formatdomain.html.in (elementsDisks): Document it.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
* docs/schemas/domaincommon.rng: Add bhyve domain type, nmdm
serial type and master and slave optional attributes for
serial that are used by nmdm
* tests/domainschematest: Add bhyvexml2argvdata directory
to validate bhyve XMLs
https://bugzilla.redhat.com/show_bug.cgi?id=1092886
Rather than point off to some nefarious "pool-specific docs" page when
describing the "format" field for the target pool provide a link to the
storage driver page which describes the various valid formats for each
pool type. Also make it a bit more clear that if a valid format isn't
specified, then the type field is ignored.
Added <capabilities> in the <features> section of LXC domains
configuration. This section can contain elements named after the
capabilities like:
<mknod state="on"/>, keep CAP_MKNOD capability
<sys_chroot state="off"/> drop CAP_SYS_CHROOT capability
Users can restrict or give more capabilities than the default using
this mechanism.
Introduce a new function to parse the provided scsi_host parent address
and unique_id value in order to find the /sys/class/scsi_host directory
which will allow a stable SCSI host address
Add a test to scsihosttest to lookup the host# name by using the PCI address
and unique_id value
Add an optional unique_id parameter to nodedev. Allows for easier lookup
and display of the unique_id value in order to document for use with
scsi_host code.
Between reboots and kernel reloads, the SCSI host number used for SCSI
storage pools may change requiring modification to the storage pool XML
in order to use a specific SCSI host adapter.
This patch introduces the "parentaddr" element and "unique_id" attribute
for the SCSI host adapter in order to uniquely identify the adapter
between reboots and kernel reloads. For now the goal is to only parse
and format the XML. Both will be required to be provided in order to
uniquely identify the desired SCSI host.
The new XML is expected to be as follows:
<adapter type='scsi_host'>
<parentaddr unique_id='3'>
<address domain='0x0000' bus='0x00' slot='0x1f' func='0x2'/>
</parentaddr>
</adapter>
where "parentaddr" is the parent device of the SCSI host using the PCI
address on which the device resides and the value from the unique_id file
for the device. Both the PCI address and unique_id values will be used
to traverse the /sys/class/scsi_host/ directories looking at each link
to match the PCI address reformatted to the directory link format where
"domain🚌slot:function" is found. Then for each matching directory
the unique_id file for the scsi_host will be used to match the unique_id
value in the xml.
For a PCI address listed above, this will be formatted to "0000:00:1f.2"
and the links in /sys/class/scsi_host will be used to find the host#
to be used for the 'scsi_host' device. Each entry is a link to the
/sys/bus/pci/devices directories, e.g.:
% ls -al /sys/class/scsi_host/host2
lrwxrwxrwx. 1 root root 0 Jun 1 00:22 /sys/class/scsi_host/host2 -> ../../devices/pci0000:00/0000:00:1f.2/ata3/host2/scsi_host/host2
% cat /sys/class/scsi_host/host2/unique_id
3
The "parentaddr" and "name" attributes are mutually exclusive to identify
the SCSI host number. Use of the "parentaddr" element will be the preferred
mechanism.
This patch only supports to parse and format the XMLs. Later patches will
add code to find out the scsi host number.
Gluster volumes don't start with a leading slash. Our schema for netfs
gluster pools enforces it though. Luckily mount.glusterfs skips it.
Allow a slashless volume name for glusterfs netfs mounts in the schema.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1101999
libvirt supports pci domain already, so update the documentation.
Otherwise users who lookup the documentation for how to use hostdev may
miss the domain and encounter error when pass-through a pci device in a
domain other than 0.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Disk type 'lun' enables SCSI command passthrough for a disk. We stated
that it works only with "block" disks. Qemu supports it also when using
the iSCSI protocol.
LXC network devices can now be assigned a custom NIC device name on the
container side. For example, this is configured with:
<interface type='network'>
<source network='default'/>
<guest dev="eth1"/>
</interface>
In this example the network card will appear as eth1 in the guest.
The previous commit 09d4d26 put the interleave at the wrong point;
it didn't allow interleaving with <memory>.
* docs/schema/domaincommon.rng (numatune): Fix interleave location.
* tests/qemuxml2argvdata/qemuxml2argv-numatune-memnode.xml: Adjust test.
Signed-off-by: Eric Blake <eblake@redhat.com>
In XML format, by definition, order of fields should not matter, so
order of parsing the elements doesn't affect the end result. When
specifying guest NUMA cells, we depend only on the order of the 'cell'
elements. With this patch all older domain XMLs are parsed as before,
but with the 'id' attribute they are parsed and formatted according to
that field. This will be useful when we have tuning settings for
particular guest NUMA node.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This patch adds support for the QEMU vhost-user feature to libvirt.
vhost-user enables the communication between a QEMU virtual machine
and other userspace process using the Virtio transport protocol.
It uses a char dev (e.g. Unix socket) for the control plane,
while the data plane based on shared memory.
The XML looks like:
<interface type='vhostuser'>
<mac address='52:54:00:3b:83:1a'/>
<source type='unix' path='/tmp/vhost.sock' mode='server'/>
<model type='virtio'/>
</interface>
Signed-off-by: Michele Paolino <m.paolino@virtualopensystems.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Add 'nocow' to storage volume xml so that user can have an option
to set NOCOW flag to the newly created volume. It's useful on btrfs
file system to enhance performance.
Btrfs has low performance when hosting VM images, even more when the guest
in those VM are also using btrfs as file system. One way to mitigate this
bad performance is to turn off COW attributes on VM files. Generally, there
are two ways to turn off COW on btrfs: a) by mounting fs with nodatacow,
then all newly created files will be NOCOW. b) per file. Add the NOCOW file
attribute. It could only be done to empty or new files.
This patch tries the second way, according to 'nocow' option, it could set
NOCOW flag per file:
for raw file images, handle 'nocow' in libvirt code; for non-raw file images,
pass 'nocow=on' option to qemu-img, and let qemu-img to handle that (requires
qemu-img version >= 2.1).
Signed-off-by: Chunyan Liu <cyliu@suse.com>
Our documentation for features was rather sparse; this fleshes out
more of the details for other existing capabilities (and cost me
some time trawling git history).
* docs/formatcaps.html.in: Document it feature bits.
Signed-off-by: Eric Blake <eblake@redhat.com>
The link to the page "how to get your code into an open source
project" has been fixed.
Signed-off-by: Michele Paolino <m.paolino@virtualopensystems.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Fix a couple of typos ('chap' should have been 'iscsi' and there was
a stray 'iqn.2013-07.com.example:iscsi-pool' entry. Clean up the
description of the <auth> element for the disk
This new module holds and formats capabilities for emulator. If you
are about to create a new domain, you may want to know what is the
host or hypervisor capable of. To make sure we don't regress on the
XML, the formatting is not something left for each driver to
implement, rather there's general format function.
The domain capabilities is a lockable object (even though the locking
is not necessary yet) which uses reference counter.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Check if the buffer is in error state and report an error if it is.
This replaces the pattern:
if (virBufferError(buf)) {
virReportOOMError();
goto cleanup;
}
with:
if (virBufferCheckError(buf) < 0)
goto cleanup;
Document typical buffer usage to favor this.
Also remove the redundant FreeAndReset - if an error has
been set via virBufferSetError, the content is already freed.
This introduces two new attributes "cmd_per_lun" and "max_sectors" same
with the names QEMU uses for virtio-scsi. An example of the XML:
<controller type='scsi' index='0' model='virtio-scsi' cmd_per_lun='50'
max_sectors='512'/>
The corresponding QEMU command line:
-device virtio-scsi-pci,id=scsi0,cmd_per_lun=50,max_sectors=512,
bus=pci.0,addr=0x3
Signed-off-by: Mike Perez <thingee@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
We publish libvirt-api.xml for others to use, and in fact, the
libvirt-python bindings use it to generate python constants that
correspond to our enum values. However, we had an off-by-one bug
that any enum that relied on C's rules for implicit initialization
of the first enum member to 0 got listed in the xml as having a
value of 1 (and all later members of the enum were equally
botched).
The fix is simple - since we add one to the previous value when
encountering an enum without an initializer, the previous value
must start at -1 so that the first enum member is assigned 0.
The python generator code has had the off-by-one ever since DV
first wrote it years ago, but most of our public enums were immune
because they had an explicit = 0 initializer. The only affected
enums are:
- virDomainEventGraphicsAddressType (such as
VIR_DOMAIN_EVENT_GRAPHICS_ADDRESS_IPV4), since commit 987e31e
(libvirt v0.8.0)
- virDomainCoreDumpFormat (such as VIR_DOMAIN_CORE_DUMP_FORMAT_RAW),
since commit 9fbaff0 (libvirt v1.2.3)
- virIPAddrType (such as VIR_IP_ADDR_TYPE_IPV4), since commit
03e0e79 (not yet released)
Thanks to Nehal J Wani for reporting the problem on IRC, and
for helping me zero in on the culprit function.
* docs/apibuild.py (CParser.parseEnumBlock): Fix implicit enum
values.
Signed-off-by: Eric Blake <eblake@redhat.com>
The interface state for bonds and vlans does seem to reflect the state
of the underlying physical devices, at least in some cases, so it
makes sense to allow reporting it (netcf now does).
The link state/speed for bridge devices is meaningless though, so we
don't even look for it.
The interface xml schema was written with strict rules about the
ordering of the elements. This was never intentional, but just due to
omission of <interleave> in the appropriate places. This patch just
adds in <interleave> wherever there is more than one element, and
re-indents everything else appropriately.
In section "Block / character devices" of "Host device assignment",
the description of hostdev element has some error:
For a block device, the type should be "storage", not "block";
For a character device, the type should be "misc", not "char".
Signed-off-by: Jincheng Miao <jmiao@redhat.com>
There are two places where you'll find info on page sizes. The first
one is under <cpu/> element, where all supported pages sizes are
listed. Then the second one is under each <cell/> element which refers
to concrete NUMA node. At this place, the size of page's pool is
reported. So the capabilities XML looks something like this:
<capabilities>
<host>
<uuid>01281cda-f352-cb11-a9db-e905fe22010c</uuid>
<cpu>
<arch>x86_64</arch>
<model>Westmere</model>
<vendor>Intel</vendor>
<topology sockets='1' cores='1' threads='1'/>
...
<pages unit='KiB' size='4'/>
<pages unit='KiB' size='2048'/>
<pages unit='KiB' size='1048576'/>
</cpu>
...
<topology>
<cells num='4'>
<cell id='0'>
<memory unit='KiB'>4054408</memory>
<pages unit='KiB' size='4'>1013602</pages>
<pages unit='KiB' size='2048'>3</pages>
<pages unit='KiB' size='1048576'>1</pages>
<distances/>
<cpus num='1'>
<cpu id='0' socket_id='0' core_id='0' siblings='0'/>
</cpus>
</cell>
<cell id='1'>
<memory unit='KiB'>4071072</memory>
<pages unit='KiB' size='4'>1017768</pages>
<pages unit='KiB' size='2048'>3</pages>
<pages unit='KiB' size='1048576'>1</pages>
<distances/>
<cpus num='1'>
<cpu id='1' socket_id='0' core_id='0' siblings='1'/>
</cpus>
</cell>
...
</cells>
</topology>
...
</host>
<guest/>
</capabilities>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Commit 7c6fc39 introduced a regression in the XML produced for older
clients. The argument at the time was that clients shouldn't be
depending on output-only data for something that is only going to
be triggered for a transient guest; but John Ferlan reported that
the automated testsuite was such a client. It's better to be safe
than sorry by guaranteeing back-compat cruft. Note that later
patches will be using <mirror> for active block commit, but there
we don't have to worry about back-compat.
* src/conf/domain_conf.c (virDomainDiskDefFormat): Restore old
style output when necessary.
* docs/schemas/domaincommon.rng: Validate back-compat style.
* docs/formatdomain.html.in: Update the documentation.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-mirror-old.xml:
Update tests.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
This new element is there to represent PCI-Express capabilities
of a PCI devices, like link speed, number of lanes, etc.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
While exposing the info under <interface/> in previous patch works, it
may work only in cases where interface is configured on the host.
However, orchestrating application may want to know the link state and
speed even in that case. That's why we ought to expose this in nodedev
XML too:
virsh # nodedev-dumpxml net_eth0_f0_de_f1_2b_1b_f3
<device>
<name>net_eth0_f0_de_f1_2b_1b_f3</name>
<path>/sys/devices/pci0000:00/0000:00:19.0/net/eth0</path>
<parent>pci_0000_00_19_0</parent>
<capability type='net'>
<interface>eth0</interface>
<address>f0🇩🇪f1:2b:1b:f3</address>
<link speed='1000' state='up'/>
<capability type='80203'/>
</capability>
</device>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Currently it is not possible to determine the speed of an interface
and whether a link is actually detected from the API. Orchestrating
platforms want to be able to determine when the link has failed and
where multiple speeds may be available which one the interface is
actually connected at. This commit introduces an extension to our
interface XML (without implementation to interface driver backends):
<interface type='ethernet' name='eth0'>
<start mode='none'/>
<mac address='aa:bb:cc:dd:ee:ff'/>
<link speed='1000' state='up'/>
<mtu size='1492'/>
...
</interface>
Where @speed is negotiated link speed in Mbits per second, and state
is the current NIC state (can be one of the following: "unknown",
"notpresent", "down", "lowerlayerdown","testing", "dormant", "up").
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Now that we track a disk mirror as a virStorageSource, we might
as well update the XML to theoretically allow any type of
mirroring destination (not just a local file). A later patch
will also be reusing <mirror> to track the block commit of the
top layer of a chain, which is another case where libvirt needs
to update the backing chain after the job is finally pivoted,
and since backing chains can have network backing files as the
destination to commit into, it makes more sense to display that
in the XML.
This patch changes output-only XML; it was already documented
that <mirror> does not affect a domain definition at this point
(because qemu doesn't provide persistent bitmaps yet). Any
application that was starting a block copy job with older libvirt
and then relying on the domain XML to determine if it was
complete will no longer be able to access the file= and format=
attributes of mirror that were previously used. However, this is
not going to be a problem in practice: the only time a block copy
job works is on a transient domain, and any app that is managing
a transient domain probably already does enough of its own
bookkeeping to know which file it is mirroring into without
having to re-read it from the libvirt XML. The one thing that
was likely to be used in a mirroring job was the ready=
attribute, which is unchanged. Meanwhile, I made sure the schema
and parser still accept the old format, even if we no longer
output it, so that upgrading from an older version of libvirt is
seamless.
* docs/schemas/domaincommon.rng (diskMirror): Alter definition.
* src/conf/domain_conf.c (virDomainDiskDefParseXML): Parse two
styles of mirror elements.
(virDomainDiskDefFormat): Output new style.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror-old.xml: New
file, copied from...
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: ...here
before modernizing.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-mirror-old*: New
files.
* tests/qemuxml2xmltest.c (mymain): Test both styles.
Signed-off-by: Eric Blake <eblake@redhat.com>
A PCI device can be associated with a specific NUMA node. Later, when
a guest is pinned to one NUMA node the PCI device can be assigned on
different NUMA node. This makes DMA transfers travel across nodes and
thus results in suboptimal performance. We should expose the NUMA node
locality for PCI devices so management applications can make better
decisions.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
At the moment we are missing even basic documentation on our
capabilities XML. Without demand on completeness, I'm
reorganizing the document structure and adding very basic
documentation to two major components of the capabilities XML.
These stubs are intended to be enhanced in the future.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
If user or management application wants to create a guest,
it may be useful to know the cost of internode latencies
before the guest resources are pinned. For example:
<capabilities>
<host>
...
<topology>
<cells num='2'>
<cell id='0'>
<memory unit='KiB'>4004132</memory>
<distances>
<sibling id='0' value='10'/>
<sibling id='1' value='20'/>
</distances>
<cpus num='2'>
<cpu id='0' socket_id='0' core_id='0' siblings='0'/>
<cpu id='2' socket_id='0' core_id='2' siblings='2'/>
</cpus>
</cell>
<cell id='1'>
<memory unit='KiB'>4030064</memory>
<distances>
<sibling id='0' value='20'/>
<sibling id='1' value='10'/>
</distances>
<cpus num='2'>
<cpu id='1' socket_id='0' core_id='0' siblings='1'/>
<cpu id='3' socket_id='0' core_id='2' siblings='3'/>
</cpus>
</cell>
</cells>
</topology>
...
</host>
...
</capabilities>
We can see the distance from node1 to node0 is 20 and within nodes 10.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Our documentation generator is a bit messy, to say the least. For
instance, the description to return values of a function is
searched within C comment. Currently, all lines that start with
'returns' or 'Returns' are viewed as return value description.
However, there are some valid uses where the 'returns' word is in
the middle of a sentence describing function behavior not the
return value. And there are no places where 'returns' is used to
describe return values. For instance:
virDomainDetachDeviceFlags, virConnectNetworkEventRegisterAny and
virDomainGetDiskErrors. This leads to HTML documemtation being
generated incorrectly.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
<interface type='hostdev' managed='yes'> is supported, but
nowhere mentions 'managed' in <interface type='hostdev'> syntax.
Update documentation to cover it.
Signed-off-by: Chunyan Liu <cyliu@suse.com>
The XML for quite a longish backing chain is shown below:
<disk type='network' device='disk'>
<driver name='qemu' type='qcow2'/>
<source protocol='nbd' name='bar'>
<host transport='unix' socket='/var/run/nbdsock'/>
</source>
<backingStore type='block' index='1'>
<format type='qcow2'/>
<source dev='/dev/HostVG/QEMUGuest1'/>
<backingStore type='file' index='2'>
<format type='qcow2'/>
<source file='/tmp/image2.qcow'/>
<backingStore type='file' index='3'>
<format type='qcow2'/>
<source file='/tmp/image3.qcow'/>
<backingStore type='file' index='4'>
<format type='qcow2'/>
<source file='/tmp/image4.qcow'/>
<backingStore type='file' index='5'>
<format type='qcow2'/>
<source file='/tmp/image5.qcow'/>
<backingStore type='file' index='6'>
<format type='raw'/>
<source file='/tmp/Fedora-17-x86_64-Live-KDE.iso'/>
<backingStore/>
</backingStore>
</backingStore>
</backingStore>
</backingStore>
</backingStore>
</backingStore>
<target dev='vdb' bus='virtio'/>
</disk>
Various disk types and formats can be mixed in one chain. The
<backingStore/> empty element marks the end of the backing chain and it
is there mostly for future support of parsing the chain provided by a
user. If it's missing, we are supposed to probe for the rest of the
chain ourselves, otherwise complete chain was provided by the user. The
index attributes of backingStore elements can be used to unambiguously
identify a specific part of the image chain.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When the default was changed from kvm to vfio, the documentation for
hostdev and interface was changed, but the documentation in <network>
was forgotten.
Also document when the default was changed from "always kvm" to "vfio
if available, else kvm" (1.0.5).
I noticed that depending on the <driver> attributes the user passed
in, the output may omit the <driver> element altogether. For example,
the rerror_policy has had this problem since commit 4bb4109 in Oct
2011. But in adding testsuite coverage to expose it, I found another
problem: the C code is just fine without a driver name, but the
XML validator required either a name or a cache mode.
* src/conf/domain_conf.c (virDomainDiskDefFormat): Update
conditional.
* docs/schemas/domaincommon.rng (diskDriver): Simplify.
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-copy-on-read.xml:
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-copy-on-read.args:
New files.
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-discard.xml:
Enhance test.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-drive-discard.xml:
Likewise.
* tests/qemuxml2argvtest.c (mymain): New test.
* tests/qemuxml2xmltest.c (mymain): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
To make <disk> schema more maintainable and to allow for moving the
pieces to a common file in the future. It relies on the ability to
override definitions as part of an include, set up in the previous
patch.
The diff is a bit hard to read, because it mixes reindentation
with refactoring; 'git diff -b --patience' may help.
* docs/schemas/domaincommon.rng (disk): Refactor into pieces.
(diskSource, diskSourceFile, diskSourceBlock, diskSourceDir)
(diskSourceVolume: New defines.
(diskSourceNetwork): Revise scope.
* docs/schemas/domainsnapshot.rng (disksnapshot): Adjust.
* tests/domainsnapshotxml2xmlin/disk-seclabel-invalid.xml,
tests/domainsnapshotxml2xmlin/disk-network-seclabel-invalid.xml: New
tests to check seclabel is forbidden in domain snapshot by schema.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
This patch is my first experience playing with nested grammars,
as documented in http://relaxng.org/tutorial-20011203.html#IDA3PZR.
I plan on doing more overrides in order to make the RelaxNG
grammar mirror the C code refactoring into a common
virStorageSource, but where different clients of that source do
not support the same subset of functionality. By starting with
something fairly easy to validate, I can make sure my later
patches will be possible.
This patch adds a use of the no-op <ref
name='sourceStartupPolicy'/> to the disksnapshot definition, so
that the snapshot version of a type='file' <source> more closely
resembles the version in domaincommon. A future patch will merge
the two files into using a common define, but this patch is
sufficient for testing that adding <source
startupPolicy='optional'/> in any of the
tests/domainsnapshotxml2xmlin/*.xml files still gets rejected
unless it occurs within the <domain> subelement, because the
definition of startupPolicy is empty outside of domain.rng.
* docs/schemas/storagecommon.rng (storageStartupPolicy)
(storageSourceExtra): Create no-op defaults.
* docs/schemas/domainsnapshot.rng (domain): Use nested grammar
to avoid restricting <domain>.
(storageSourceExtra): Create new override.
(disksnapshot): Access overrides through common names.
* docs/schemas/domaincommon.rng (disk): Access overrides through
common names.
* docs/schemas/domain.rng (storageStartupPolicy)
(storageSourceExtra): Create new overrides.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Domain snapshots should only permit an external snapshot into
a storage format that permits a backing chain, since the new
snapshot file necessarily must be backed by the existing file.
The C code for the qemu driver is a little bit stricter in
currently enforcing only qcow2 or qed, but at the XML parser
level, including virt-xml-validate, it is fairly easy to
enforce that a user can't request a 'raw' external snapshot.
* docs/schemas/storagecommon.rng (storageFormat): Split out...
(storageFormatBacking): ...new sublist.
* docs/schemas/domainsnapshot.rng (disksnapshotdriver): Use new
type.
* src/util/virstoragefile.h (virStorageFileFormat): Rearrange for
easier code management.
* src/util/virstoragefile.c (virStorageFileFormat, fileTypeInfo):
Likewise.
* src/conf/snapshot_conf.c (virDomainSnapshotDiskDefParseXML): Use
new marker to limit selection of formats.
Signed-off-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
We had incomplete RelaxNG support for storage formats listed
in virstoragefile.h: commit 027bf2e added 'vdi' but forgot
to update the <volume> and <domain> xml lists; the <volume>
list was also missing 'fat' and 'vhd'. Maintaining two lists
is a recipe for them getting out of sync, so make the list
common so that both contexts benefit the next time we add a
format in a single location.
* docs/schemas/domaincommon.rng (storageFormat): Move...
* docs/schemas/storagecommon.rng: ...here, and add vdi.
* docs/schemas/storagevol.rng (formatfile): Use common list.
Signed-off-by: Eric Blake <eblake@redhat.com>
In general, we try to make virt-xml-validate tolerant of input
elements in any order when possible. However, as written, the
RNG grammar did not permit <source> unless there was an explicit
type= attribute (even though the C code manages just fine by
defaulting to type='file'). After making the attribute optional
on the 'file' branch, I noticed that the use of diskspec was now
redundant with the branch when no <source> was supplied.
View this patch with 'git diff -b' for a better picture of the
schema change.
* docs/schemas/domaincommon.rng (disk): Hoist 'diskspec' out of
choice, make type='file' default, and still preserve interleave.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-source-pool.xml:
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-drive-discard.xml:
New files.
* tests/qemuxml2argvdata/qemuxml2argv-disk-source-pool.xml:
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-discard.xml:
Reorder XML.
* tests/qemuxml2xmltest.c (mymain): Cover new files.
Signed-off-by: Eric Blake <eblake@redhat.com>
Having two tiny files with a couple definitions didn't make
as much sense as one common file, especially since I plan to
add more definitions and use it in more places.
* docs/schemas/storageencryption.rng: Merge this...
* docs/schemas/storagefilefeatures.rng: ...and this, into...
* docs/schemas/storagecommon.rng: ...this new file.
* docs/schemas/Makefile.am (schema_DATA): Reflect renames.
* docs/schemas/storagevol.rng: Likewise.
* docs/schemas/domaincommon.rng: Likewise.
* libvirt.spec.in: Likewise.
* mingw-libvirt.spec.in: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
According to our documentation the "key" value has the following
meaning: "Providing an identifier for the volume which identifies a
single volume." The currently used keys for gluster volumes consist of
the gluster volume name and file path. This can't be considered unique
as a different storage server can serve a volume with the same name.
Unfortunately I wasn't able to figure out a way to retrieve the gluster
volume UUID which would avoid the possibility of having two distinct
keys identifying a single volume.
Use the full URI as the key for the volume to avoid the more critical
ambiguity problem and document the possible change to UUID.
This patch adds an element to QEMU's capability XML, to
show if the underlying QEMU binary supports the live disk
snapshotting or not.
This allows any client to know ahead of time if the feature
is available.
Without this information available, the only way to check
for the snapshot support is to request one and check for
errors.
Signed-off-by: Francesco Romani <fromani@redhat.com>
A earlier commit changed the global log buffer so that it only
records messages that are explicitly requested via the log
filters setting. This removes the performance burden, and
improves the signal/noise ratio for messages in the global
buffer. At the same time though, it is somewhat pointless, since
all the recorded log messages are already going to be sent to an
explicit log output like syslog, stderr or the journal. The
global log buffer is thus just duplicating this data on stderr
upon crash.
The log_buffer_size config parameter is left in the augeas
lens to prevent breakage for users on upgrade. It is however
completely ignored hereafter.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Any source file which calls the logging APIs now needs
to have a VIR_LOG_INIT("source.name") declaration at
the start of the file. This provides a static variable
of the virLogSource type.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=862887
Add a netmask for the source and destination IP address for the
ebtables --arp-ip-src and --arp-ip-dst options. Extend the XML
parser with support for XML attributes for these netmasks similar
to already supported netmasks. Extend the documentation.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This is a request for adding a VMmanager application as requested and
described by Ksenya Phil.
Signed-off-by: Ksenya Phil <philka2003@mail.ru>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
With most of our storage backends it's possible to have two separate
volume keys to point to a single volume. (By creating sym/hard-links to
local files or by mounting remote filesystems to two different locations
and creating pools on top of them) Document this possibility.
Auditing all callers of virCommandRun and virCommandWait that
passed a non-NULL pointer for exit status turned up some
interesting observations. Many callers were merely passing
a pointer to avoid the overall command dying, but without
caring what the exit status was - but these callers would
be better off treating a child death by signal as an abnormal
exit. Other callers were actually acting on the status, but
not all of them remembered to filter by WIFEXITED and convert
with WEXITSTATUS; depending on the platform, this can result
in a status being reported as 256 times too big. And among
those that correctly parse the output, it gets rather verbose.
Finally, there were the callers that explicitly checked that
the status was 0, and gave their own message, but with fewer
details than what virCommand gives for free.
So the best idea is to move the complexity out of callers and
into virCommand - by default, we return the actual exit status
already cleaned through WEXITSTATUS and treat signals as a
failed command; but the few callers that care can ask for raw
status and act on it themselves.
* src/util/vircommand.h (virCommandRawStatus): New prototype.
* src/libvirt_private.syms (util/command.h): Export it.
* docs/internals/command.html.in: Document it.
* src/util/vircommand.c (virCommandRawStatus): New function.
(virCommandWait): Adjust semantics.
* tests/commandtest.c (test1): Test it.
* daemon/remote.c (remoteDispatchAuthPolkit): Adjust callers.
* src/access/viraccessdriverpolkit.c (virAccessDriverPolkitCheck):
Likewise.
* src/fdstream.c (virFDStreamCloseInt): Likewise.
* src/lxc/lxc_process.c (virLXCProcessStart): Likewise.
* src/qemu/qemu_command.c (qemuCreateInBridgePortWithHelper):
Likewise.
* src/xen/xen_driver.c (xenUnifiedXendProbe): Simplify.
* tests/reconnect.c (mymain): Likewise.
* tests/statstest.c (mymain): Likewise.
* src/bhyve/bhyve_process.c (virBhyveProcessStart)
(virBhyveProcessStop): Don't overwrite virCommand error.
* src/libvirt.c (virConnectAuthGainPolkit): Likewise.
* src/openvz/openvz_driver.c (openvzDomainGetBarrierLimit)
(openvzDomainSetBarrierLimit): Likewise.
* src/util/virebtables.c (virEbTablesOnceInit): Likewise.
* src/util/viriptables.c (virIpTablesOnceInit): Likewise.
* src/util/virnetdevveth.c (virNetDevVethCreate): Fix debug
message.
* src/qemu/qemu_capabilities.c (virQEMUCapsInitQMP): Add comment.
* src/storage/storage_backend_iscsi.c
(virStorageBackendISCSINodeUpdate): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
When probing QEMU capabilities fails for a binary generate a
log message with MESSAGE_ID==8ae2f3fb-2dbe-498e-8fbd-012d40afa361.
This can be directly queried from journald based on the UUID
instead of needing string grep. This lets tools like libguestfs'
bug reporting tool trivially do automated sanity tests on the
host they're running on.
$ journalctl MESSAGE_ID=8ae2f3fb-2dbe-498e-8fbd-012d40afa361
Feb 21 17:11:01 localhost.localdomain lt-libvirtd[9196]:
Failed to probe capabilities for /bin/qemu-system-alpha:
internal error: Child process (LC_ALL=C LD_LIBRARY_PATH=
/home/berrange/src/virt/libvirt/src/.libs PATH=/usr/lib64/
ccache:/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:
/usr/bin:/root/bin HOME=/root USER=root LOGNAME=root
/bin/qemu-system-alpha -help) unexpected exit status 127:
/bin/qemu-system-alpha: error while loading shared libraries:
libglapi.so.0: cannot open shared object file: No such file
or directory
$ journalctl MESSAGE_ID=8ae2f3fb-2dbe-498e-8fbd-012d40afa361 --output=json
{ ...snip...
"LIBVIRT_SOURCE" : "file",
"PRIORITY" : "3",
"CODE_FILE" : "qemu/qemu_capabilities.c",
"CODE_LINE" : "2770",
"CODE_FUNC" : "virQEMUCapsLogProbeFailure",
"MESSAGE_ID" : "8ae2f3fb-2dbe-498e-8fbd-012d40afa361",
"LIBVIRT_QEMU_BINARY" : "/bin/qemu-system-xtensa",
"MESSAGE" : "Failed to probe capabilities for /bin/qemu-system-xtensa:
internal error: Child process (LC_ALL=C LD_LIBRARY_PATH=/home/berrange
/src/virt/libvirt/src/.libs PATH=/usr/lib64/ccache:/usr/local/sbin:
/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/root/bin HOME=/root
USER=root LOGNAME=root /bin/qemu-system-xtensa -help) unexpected
exit status 127: /bin/qemu-system-xtensa: error while loading shared
libraries: libglapi.so.0: cannot open shared object file: No such
file or directory\n" }
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
When a virError is raised, pass the error domain and code
onto the systemd journald using metadata fields.
This allows error messages to be queried by code eg
$ journalctl LIBVIRT_CODE=43
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The logging doc had a hand-written table of contents
instead of using the automatic XSL generated one.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Recent autotest/virt-test testing on f20 discovered an anomaly in how
the bandwidth options are documented and used. This was discovered due
to a bug fix in the /sbin/tc utility found in iproute-3.11.0.1 (on f20)
in which overflow was actually caught and returned as an error. The fix
was first introduced in iproute-3.10 (search on iproute2 commit 'a303853e').
The autotest/virt-test test for virsh domiftune was attempting to send
the largest unsigned integer value (4294967295) for maximum value
testing. The libvirt xml implementation was designed to manage values
in kilobytes thus when this value was passed to /sbin/tc, it (now)
properly rejected the 4294967295kbps value.
Investigation of the problem discovered that formatdomain.html.in and
formatnetwork.html.in described the elements and property types slightly
differently, although they use the same code - virNetDevBandwidthParseRate()
(shared by portgroups, domains, and networks xml parsers). Rather than
have the descriptions in two places, this patch will combine and reword
the description under formatnetwork.html.in and have formatdomain.html.in
link to that description.
This documentation faux pas was continued into the virsh man page where
the bandwidth description for both 'attach-interface' and 'domiftune'
did not indicate the format of each value, thus leading to the test using
largest unsigned integer value assuming "bps" rather than "kbps", which
ultimately was wrong.
The previous OOM testing support would re-run the entire "main"
method each iteration, failing a different malloc each time.
When a test suite has 'n' allocations, the number of repeats
requires is (n * (n + 1) ) / 2. This gets very large, very
quickly.
This new OOM testing support instead integrates at the
virtTestRun level, so each individual test case gets repeated,
instead of the entire test suite. This means the values of
'n' are orders of magnitude smaller.
The simple usage is
$ VIR_TEST_OOM=1 ./qemuxml2argvtest
...
29) QEMU XML-2-ARGV clock-utc ... OK
Test OOM for nalloc=36 .................................... OK
30) QEMU XML-2-ARGV clock-localtime ... OK
Test OOM for nalloc=36 .................................... OK
31) QEMU XML-2-ARGV clock-france ... OK
Test OOM for nalloc=38 ...................................... OK
...
the second lines reports how many mallocs have to be failed, and thus
how many repeats of the test will be run.
If it crashes, then running under valgrind will often show the problem
$ VIR_TEST_OOM=1 ../run valgrind ./qemuxml2argvtest
When debugging problems it is also helpful to select an individual
test case
$ VIR_TEST_RANGE=30 VIR_TEST_OOM=1 ../run valgrind ./qemuxml2argvtest
When things get really tricky, it is possible to request that just
specific allocs are failed. eg to fail allocs 5 -> 12, use
$ VIR_TEST_RANGE=30 VIR_TEST_OOM=1:5-12 ../run valgrind ./qemuxml2argvtest
In the worse case, you might want to know the stack trace of the
alloc which was failed then VIR_TEST_OOM_TRACE can be set. If it
is set to 1 then it will only print if it thinks a mistake happened.
This is often not reliable, so setting it to 2 will make it print
the stack trace for every alloc that is failed.
$ VIR_TEST_OOM_TRACE=2 VIR_TEST_RANGE=30 VIR_TEST_OOM=1:5-5 ../run valgrind ./qemuxml2argvtest
30) QEMU XML-2-ARGV clock-localtime ... OK
Test OOM for nalloc=36 !virAllocN
/home/berrange/src/virt/libvirt/src/util/viralloc.c:180
virHashCreateFull
/home/berrange/src/virt/libvirt/src/util/virhash.c:144
virDomainDefParseXML
/home/berrange/src/virt/libvirt/src/conf/domain_conf.c:11745
virDomainDefParseNode
/home/berrange/src/virt/libvirt/src/conf/domain_conf.c:12646
virDomainDefParse
/home/berrange/src/virt/libvirt/src/conf/domain_conf.c:12590
testCompareXMLToArgvFiles
/home/berrange/src/virt/libvirt/tests/qemuxml2argvtest.c:106
virtTestRun
/home/berrange/src/virt/libvirt/tests/testutils.c:250
mymain
/home/berrange/src/virt/libvirt/tests/qemuxml2argvtest.c:418 (discriminator 2)
virtTestMain
/home/berrange/src/virt/libvirt/tests/testutils.c:750
??
??:0
_start
??:?
FAILED
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
There is no keyboard support currently in libvirt.
For some platforms (PPC64 QEMU) this makes graphics unusable,
since the keyboard is not implicit and it can't be added via libvirt.
Signed-off-by: Li Zhang <zhlcindy@linux.vnet.ibm.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
There might be some use cases, where user wants to prepare the host or
its environment prior to starting a network and do some cleanup after
the network has been shut down. Consider all the functionality that
libvirt doesn't currently have as an example what a hook script can
possibly do.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Add support for gluster backed images as sources for snapshots in the
qemu driver. This will also simplify adding further network backed
volumes as sources for snapshot in case qemu will support them.
Add a new character device backend called 'spiceport' that uses
spice's channel for communications and apart from spicevmc can be used
as a backend for any character device from libvirt's point of view.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Some grammar fixes.
s/namespace,set/namespace, set
s/container being allowed/container are allowed
s/the <code>uid/The <code>uid
Signed-off-by: Chen Hanxiao <chenhanxiao@cn.fujitsu.com>
Add a new <timer> for the HyperV reference time counter enlightenment
and the iTSC reference page for Windows guests.
This feature provides a paravirtual approach to track timer events for
the guest (similar to kvmclock) with the option to use real hardware
clock on systems with a iTSC with compensation across various hosts.
According to the documentation describing various tunables for domain
timers not all the fields are supported by all the driver types. Express
these in the RNG:
- rtc, platform: Only these support the "track" attribute.
- tsc: only one to support "frequency" and "mode" attributes
- hpet, pit: tickpolicy/catchup attribute/element
- kvmclock: no extra attributes are supported
Additionally the attributes of the <catchup> element for
tickpolicy='catchup' are optional according to the parsing code. Express
this in the XML and fix a spurious space added while formatting the
<catchup> element and add tests for it.
https://bugzilla.redhat.com/show_bug.cgi?id=1057321
pointed out that we weren't honoring the <bandwidth> element in
libvirt networks using <forward mode='bridge'/>. In fact, these
networks are just a method of giving a libvirt network name to an
existing Linux host bridge on the system, and libvirt doesn't have
enough information to know where to set such limits. We are working on
a method of supporting network bandwidths for some specific cases of
<forward mode='bridge'/>, but currently libvirt doesn't support it. So
the proper thing to do now is just log an error when someone tries to
put a <bandwidth> element in that type of network. (It's unclear if we
will be able to do proper bandwidth limiting for macvtap networks, and
most definitely we will not be able to support it for hostdev
networks).
While looking through the network XML documentation and comparing it
to the networkValidate function, I noticed that we also ignore the
presence of a mac address in the config in the same cases, rather than
failing so that the user will understand that their desired action has
not been taken.
This patch updates networkValidate() (which is called any time a
persistent network is defined, or a transient network created) to log
an error and fail if it finds either a <bandwidth> or <mac> element
and the network forward mode is anything except 'route'. 'nat', or
nothing. (Yes, neither of those elements is acceptable for any macvtap
mode, nor for a hostdev network).
NB: This does *not* cause failure to start any existing network that
contains one of those elements, so someone might have erroneously
defined such a network in the past, and that network will continue to
function unmodified. I considered it too disruptive to suddenly break
working configs on the next reboot after a libvirt upgrade.
While at it, also relinquish active commit rights:
[x years between commits] is probably a poster child example of inactivity :)
Signed-off-by: Eric Blake <eblake@redhat.com>
The project has historically operated as a meritocratic
consensus based community. Formally document what has
always been an unwritten assumption amongst the community
participants. Also include an explicit code of conduct
to preempt any potential, but unlikely, future problems.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
It breaks the build on RHEL-5.10 and because it's only optional we
could remove it from the code. The default namespace will be used.
This hunk was introduced by commit 237a088ba4.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
It doesn't make sense to fail if the SCSI host device is specified
as "shareable" explicitly between domains (NB, it works if and only
if the device is specified as "shareable" for *all* domains,
otherwise it fails).
To fix the problem, this patch introduces an array for virSCSIDevice
struct, which records all the names of domain which are using the
device (note that the recorded domains must specify the device as
shareable). And the change on the data struct brings on many
subsequent changes in the code.
Prior to this patch, the "shareable" tag didn't work as expected,
it actually work like "non-shareable". So this patch also added notes
in formatdomain.html to declare the fact.
* src/util/virscsi.h:
- Remove virSCSIDeviceGetUsedBy
- Change definition of virSCSIDeviceGetUsedBy and virSCSIDeviceListDel
- Add virSCSIDeviceIsAvailable
* src/util/virscsi.c:
- struct virSCSIDevice: Change "used_by" to be an array; Add
"n_used_by" as the array count
- virSCSIDeviceGetUsedBy: Removed
- virSCSIDeviceFree: frees the "used_by" array
- virSCSIDeviceSetUsedBy: Copy the domain name to avoid potential
memory corruption
- virSCSIDeviceIsAvailable: New
- virSCSIDeviceListDel: Change the logic, for device which is already
in the list, just remove the corresponding entry in "used_by". And
since it's only used in one place, we can safely removing the code
to find out the dev in the list first.
- Copyright updating
* src/libvirt_private.sys:
- virSCSIDeviceGetUsedBy: Remove
- virSCSIDeviceIsAvailable: New
* src/qemu/qemu_hostdev.c:
- qemuUpdateActiveScsiHostdevs: Check if the device existing before
adding it to the list;
- qemuPrepareHostdevSCSIDevices: Error out if the not all domains
use the device as "shareable"; Also don't try to add the device
to the activeScsiHostdevs list if it already there; And make
more sensible error w.r.t the current "shareable" value in
driver->activeScsiHostdevs.
- qemuDomainReAttachHostScsiDevices: Change the logic according
to the changes on helpers.
Signed-off-by: Osier Yang <jyang@redhat.com>
Add support for specifying various types when doing snapshots. This will
later allow to do snapshots on network backed volumes. Disks of type
'volume' are not supported by snapshots (yet).
Also amend the test suite to check parsing of the various new disk
types that can now be specified.
Quite often, I need to cite URLs like
http://libvirt.org/formatnetwork.html#elementQoS
but it is annoying to copy them from the table of contents or the html
source.
This patch borrows from the Python documentation in order to make it
easier to cite headers on libvirt's oneline documentation.
spice-server offers an API to disable file transfer messages
on the agent channel between the client and the guest.
This is supported in qemu through the disable-agent-file-xfer option.
This patch exposes this option to libvirt.
Adds a new element 'filetransfer', with one property,
'enable', which accepts a boolean.
Default is enabled, for backward compatibility.
Depends on the capability exported in the first patch of the series.
Signed-off-by: Francesco Romani <fromani@redhat.com>
This patch introduces new xml elements under <blkiotune>,
we use these new elements to setup the throttle blkio
cgroup for domain. The new blkiotune node looks like this:
<blkiotune>
<device>
<path>/path/to/block</path>
<weight>1000</weight>
<read_iops_sec>10000</read_iops_sec>
<write_iops_sec>10000</write_iops_sec>
<read_bytes_sec>1000000</read_bytes_sec>
<write_bytes_sec>1000000</write_bytes_sec>
</device>
</blkiotune>
Signed-off-by: Guan Qiang <hzguanqiang@corp.netease.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Mitre tried to assign us two separate CVEs for the fix for
https://bugzilla.redhat.com/show_bug.cgi?id=1047577, on the
grounds that the fixes were separated by more than an hour
and thus triggered different hourly snapshots. But we
explicitly do NOT want to treat transient security bugs as
CVEs if they can only be triggered by patches in libvirt.git
but where the problem is cleaned up before a formal release.
Meanwhile, I noticed that while our wiki mentioned maintenance
branches and releases, our formal documentation did not.
* docs/downloads.html.in: Contrast hourly snapshots with
maintenance branches.
Signed-off-by: Eric Blake <eblake@redhat.com>
When idmap was added to LXC, we forgot to cover it in the testsuite.
The schema was missing an <element> layer, and as a result,
virt-xml-validate was failing on valid dumpxml output.
Reported by Eduard - Gabriel Munteanu on IRC.
* docs/schemas/domaincommon.rng (idmap): Include <idmap> element,
and support interleaves.
* tests/lxcxml2xmldata/lxc-idmap.xml: New file.
* tests/lxcxml2xmltest.c (mymain): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
The datatype.c object checks could result in a message like:
error: invalid connection pointer in no connection
This consolidates all clients of this message to have uniform contents:
error: invalid connection pointer in someFunc
Note that virCheckConnectReturn raises an error immediately; in
datatypes.c, where we don't need to raise the error (but instead
just leave it in the thread-local setting), we use
virCheckConnectGoto and the cleanup label instead. Then, for
consistency in that file, all subsequent error messages are
touched to also use the cleanup error label.
* src/datatypes.h (virCheckConnectReturn)
(virCheckConnectGoto): New macros.
* src/datatypes.c: Use new macro.
* src/libvirt-qemu.c (virDomainQemuAttach): Likewise.
(virLibConnError): Delete unused macro.
* src/libvirt-lxc.c (virLibConnError): Likewise.
* src/libvirt.c: Use new macro throughout.
* docs/api_extension.html.in: Modernize documentation.
Signed-off-by: Eric Blake <eblake@redhat.com>
AArch64 qemu has similar behavior as armv7l, like use of mmio etc.
This patch adds similar bypass checks what we have for armv7l to aarch64.
E.g. we are enabling mmio transport for Nicdev.
Making addDefaultUSB and addDefaultMemballoon to false etc.
V3:
- Adding missing domain rng schema for aarcg64 and test case in
testutilsqemu.c which was causing test suite failure
while running make check.
V2:
- Added testcase to qemuxml2argvtest as suggested
during review comments of V1.
V1:
- Initial patch.
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
https://bugzilla.redhat.com/show_bug.cgi?id=1035118
When outputting the XML for the RNG device, the code didn't format the
PCI address info. Additionally the schema wasn't expecting the info
although it was being parsed and used internally. Fix those mistakes and
add test for the PCI info section.
Add a link to the http://sandbox.libvirt.org sub-site from the
list of libraries related to libvirt. Also fix formatting for
the ruby libvirt binding.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Adds a new page to the website "Deployment" section describing
what data is sent to the audit logs and how to configure libvirtd
audit settings.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
In the 'directory' and 'netfs' storage pools, a user can see
both 'file' and 'dir' storage volume types, to know when they
can descend into a subdirectory. But in a network-based storage
pool, such as the upcoming 'gluster' pool, we use 'network'
instead of 'file', and did not have any counterpart for a
directory until this patch. Adding a new volume type
'network-dir' is better than reusing 'dir', because it makes
it clear that the only way to access 'network' volumes within
that container is through the network mounting (leaving 'dir'
for something accessible in the local file system).
* include/libvirt/libvirt.h.in (virStorageVolType): Expand enum.
* docs/formatstorage.html.in: Document it.
* docs/schemasa/storagevol.rng (vol): Allow new value.
* src/conf/storage_conf.c (virStorageVol): Use new value.
* src/qemu/qemu_command.c (qemuBuildVolumeString): Fix client.
* src/qemu/qemu_conf.c (qemuTranslateDiskSourcePool): Likewise.
* tools/virsh-volume.c (vshVolumeTypeToString): Likewise.
* src/storage/storage_backend_fs.c
(virStorageBackendFileSystemVolDelete): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Add support for a new <pool type='gluster'>, similar to
RBD and Sheepdog. Terminology wise, a gluster volume
forms a libvirt storage pool, within the gluster volume,
individual files are treated as libvirt storage volumes.
* docs/schemas/storagepool.rng (poolgluster): New pool type.
* docs/formatstorage.html.in: Document gluster.
* docs/storage.html.in: Likewise, and contrast it with netfs.
* tests/storagepoolxml2xmlin/pool-gluster.xml: New test.
* tests/storagepoolxml2xmlout/pool-gluster.xml: Likewise.
* tests/storagepoolxml2xmltest.c (mymain): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
I got annoyed at having to use both 'virsh vol-list $pool --details'
AND 'virsh vol-dumpxml $vol $pool' to learn if I had populated
the volume correctly. Since two-thirds of the data present in
virStorageVolGetInfo() already appears in virStorageVolGetXMLDesc(),
this just adds the remaining piece of information, as:
<volume type='...'>
...
</volume>
* docs/formatstorage.html.in: Document new <volume type=...>.
* docs/schemas/storagevol.rng (vol): Add it to RelaxNG.
* src/conf/storage_conf.h (virStorageVolTypeToString): Declare.
* src/conf/storage_conf.c (virStorageVolTargetDefFormat): Output
the metatype.
(virStorageVolDefParseXML): Parse it, for unit tests.
* tests/storagevolxml2xmlout/vol-*.xml: Update tests to match.
Signed-off-by: Eric Blake <eblake@redhat.com>
The RNG grammar did not allow arbitrary interleaving, which makes
it harder than necessary to create a new volume from handwritten XML.
(Compare also to commit caf516db for pools).
* docs/schemas/storagevol.rng: Support interleaving.
* tests/storagevolxml2xmlin/vol-file-backing.xml: Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Older xmllint version don't allow such characters in datatype anyURI.
In order not to change too much, I'm suggesting making a choice of
anyURI or 'absPathName' which should be fine (checked with upstream
and that old xmllint, both work fine).
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
$ touch /var/lib/libvirt/images/'a<b>c'
$ virsh pool-refresh default
$ virsh vol-dumpxml 'a<b>c' default | head -n2
<volume>
<name>a<b>c</name>
Oops. That's not valid XML. And when we fix the XML
generation, it fails RelaxNG validation.
I'm also tired of seeing <key>(null)</key> in the example
output for volume xml; while we used NULLSTR() to avoid
a NULL deref rather than relying on glibc's printf
extension behavior, it's even better if we avoid the issue
in the first place. But this requires being careful that
we don't invalidate any storage backends that were relying
on key being unassigned during virStoragVolCreateXML[From].
I would have split this into two patches (one for escaping,
one for avoiding <key>(null)</key>), but since they both
end up touching a lot of the same test files, I ended up
merging it into one.
Note that this patch allows pretty much any volume name
that can appear in a directory (excluding . and .. because
those are special), but does nothing to change the current
(unenforced) RelaxNG claim that pool names will consist
only of letters, numbers, _, -, and +. Tightening the C
code to match RelaxNG patterns and/or relaxing the grammar
to match the C code for pool names is a task for another
day (but remember, we DID recently tighten C code for
domain names to exclude a leading '.').
* src/conf/storage_conf.c (virStoragePoolSourceFormat)
(virStoragePoolDefFormat, virStorageVolTargetDefFormat)
(virStorageVolDefFormat): Escape user-controlled strings.
(virStorageVolDefParseXML): Parse key, for use in unit tests.
* src/storage/storage_driver.c (storageVolCreateXML)
(storageVolCreateXMLFrom): Ensure parsed key doesn't confuse
volume creation.
* docs/schemas/basictypes.rng (volName): Relax definition.
* tests/storagepoolxml2xmltest.c (mymain): Test it.
* tests/storagevolxml2xmltest.c (mymain): Likewise.
* tests/storagepoolxml2xmlin/pool-dir-naming.xml: New file.
* tests/storagepoolxml2xmlout/pool-dir-naming.xml: Likewise.
* tests/storagevolxml2xmlin/vol-file-naming.xml: Likewise.
* tests/storagevolxml2xmlout/vol-file-naming.xml: Likewise.
* tests/storagevolxml2xmlout/vol-*.xml: Fix fallout.
Signed-off-by: Eric Blake <eblake@redhat.com>
Enforce and document the style set up by the previous patches.
* build-aux/bracket-spacing.pl: Add comma checks.
* docs/hacking.html.in: Document the rules.
* HACKING: Regenerate.
Signed-off-by: Eric Blake <eblake@redhat.com>
While trying to compare netfs against my new gluster pool, I
discovered two things:
virt-xml-validate chokes on valid xml produced by 'virsh pool-dumpxml'
[yet another reason that ALL patches that add new xml should be adding
corresponding tests]
When using glusterfs FUSE mounts, you cannot access a subdirectory
of a gluster volume. The recommended workaround in the gluster
community is to mount the volume to an intermediate location, then
bind-mount the desired subdirectory to the final location. Maybe
we should teach libvirt to do bind-mounting, but for now I chose to
just document the limitation.
* docs/storage.html.in: Improve documentation.
* docs/schemas/storagepool.rng (sourcefmtnetfs): Allow all
formats, and drop redundant info-vendor.
* tests/storagepoolxml2xmltest.c (mymain): New test.
* tests/storagepoolxml2xmlin/pool-netfs-gluster.xml: New file.
* tests/storagepoolxml2xmlout/pool-netfs-gluster.xml: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
As of libvirt 1.1.1 and systemd 205, the cgroups layout used by
libvirt has some changes. Update the 'cgroups.html' file from
the website to describe how it works in a systemd world.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The linux kernel recently added support for paravirtual spinlock
handling to avoid performance regressions on overcomitted hosts. This
feature needs to be turned in the hypervisor so that the guest OS is
notified about the possible support.
This patch adds a new feature "paravirt-spinlock" to the XML and
supporting code to enable the "kvm_pv_unhalt" pseudo CPU feature in
qemu.
https://bugzilla.redhat.com/show_bug.cgi?id=1008989
Starting from v2.4 (released today!), SystemTap can use libvirt to
execute scripts inside virtual machines.
Signed-off-by: Eric Blake <eblake@redhat.com>
There are two forms used throughout libvirt code comments, which
are both supported by this patch.
* plain links like e.g. http://www.libvirt.org/
* links enclosed in <> characters, e.g. <http://www.libvirt.org/>
Signed-off-by: Claudio Bley <cbley@av-test.de>
Expand the "secmodel" XML fragment of "host" with a sequence of
baselabel's which describe the default security context used by
libvirt with a specific security model and virtualization type:
<secmodel>
<model>selinux</model>
<doi>0</doi>
<baselabel type='kvm'>system_u:system_r:svirt_t:s0</baselabel>
<baselabel type='qemu'>system_u:system_r:svirt_tcg_t:s0</baselabel>
</secmodel>
<secmodel>
<model>dac</model>
<doi>0</doi>
<baselabel type='kvm'>107:107</baselabel>
<baselabel type='qemu'>107:107</baselabel>
</secmodel>
"baselabel" is driver-specific information, e.g. in the DAC security
model, it indicates USER_ID:GROUP_ID.
Signed-off-by: Giuseppe Scrivano <gscrivan@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The RNG grammar did not allow arbitrary interleaving, which makes
it harder than necessary to create a new pool from handwritten XML.
* docs/schemas/storagepool.rng: Allow interleaving.
* tests/storagepoolxml2xmlin/pool-sheepdog.xml: Test interleave.
* tests/storagepoolxml2xmlin/pool-iscsi-auth.xml: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
We forgot to document several pool types.
* docs/formatstorage.html.in: Add docs for scsi, mpath, rbd, and
sheepdog.
Signed-off-by: Eric Blake <eblake@redhat.com>
Start a page describing some of the things that applications
using libvirt need to bear in mind to ensure security of their
systems.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Prefer using VFIO (if available) to the legacy KVM device passthrough.
With this patch a PCI passthrough device without the driver configured
will be started with VFIO if it's available on the host. If not legacy
KVM passthrough is checked and error is reported if it's not available.
Since 76b644c when the support for RAM filesystems was introduced,
libvirt accepted the following XML:
<source usage='1024' unit='KiB'/>
This was parsed correctly and internally stored in bytes, but it
was formatted as (with an extra 's'):
<source usage='1024' units='KiB'/>
When read again, this was treated as if the units were missing,
meaning libvirt was unable to parse its own XML correctly.
The usage attribute was documented as being in KiB, but it was not
scaled if the unit was missing. Transient domains still worked,
because this was balanced by an extra 'k' in the mount options.
This patch:
Changes the parser to use 'units' instead of 'unit', as the latter
was never documented (fixing persistent domains) and some programs
(libvirt-glib, libvirt-sandbox) already parse the 'units' attribute.
Removes the extra 'k' from the tmpfs mount options, which is needed
because now we parse our own XML correctly.
Changes the default input unit to KiB to match documentation, fixing:
https://bugzilla.redhat.com/show_bug.cgi?id=1015689
Commit id 'c4a4603de' added an output <path> to the nodedev xml, but
did not update the schema.
This resulted in the failure of the 'virt-xml-validate' on a file
generated by 'virsh nodedev-dumpxml pci_0000_00_00_0' (for example).
This was found/seen by running autotest on my host.
This resolves one of the issues in:
https://bugzilla.redhat.com/show_bug.cgi?id=1003983
This device is identical to qemu's "intel-hda" device (known as "ich6"
in libvirt), but has a different PCI device ID (which matches the ID
of the hda audio built into the ich9 chipset, of course). It's not
supported in earlier versions of qemu, so it requires a capability
bit.
The xml files are generated in build directory and thus docs/newapi.xsl
was not able to find them in a VPATH build.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Useful to set custom forwarders instead of using the contents of
/etc/resolv.conf. It helps me to setup dnsmasq as local nameserver to
resolve VM domain names from domain 0, when domain option is used.
Signed-off-by: Diego Woitasen <diego.woitasen@vhgroup.net>
Signed-off-by: Eric Blake <eblake@redhat.com>
Currently the XML parser already allows the following syntax:
<disk type='block' device='cdrom'>
<source startupPolicy='optional'/>
<target dev='hda' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
But it if the dev value is NULL then it would not have the leading
"<source ", resulting in invalid XML.
qemu/KVM also supports a tftp URL while specifying the cdrom ISO image.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='tftp' name='/url/path'>
<host name='host.name' port='69'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
The ftps protocol is another protocol supported by qemu/KVM while specifying
the cdrom ISO image.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='ftps' name='/url/path'>
<host name='host.name' port='990'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
The https protocol is also accepted by qemu/KVM when specifying the cdrom ISO
image.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='https' name='/url/path'>
<host name='host.name' port='443'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
Describe some of the issues to be aware of when configuring LXC
guests with security isolation as a goal.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
First make sure that the input is xhtml as the stylesheets expect
namespaced element, then use a span element instead of a as a
is treated specially, finally adjust the makefile to check for
the new span element and replace it with the PHP code
Mention that user namespace can be enabled using the UID/GID
mapping schema.
Fix typo in link anchor for container args in domain XML docs.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Commits 905629f4 and 1716e7a6 have added support for specifying
an IPv4 range and a port range to be used by NAT:
<forward mode='nat'>
<nat>
<address start='10.20.30.40' end='10.20.30.44'/>
<port start='60000' end='65432'/>
</nat>
</forward>
https://bugzilla.redhat.com/show_bug.cgi?id=1004364
According to VMWare's documentation 'cdrom-raw' is an acceptable value
for deviceType for a CD-ROM drive. The documentation states that the VMX
configuration for a CD-ROM deviceType is as follows:
ide|scsi(n):(n).deviceType = "cdrom-raw|atapi-cdrom|cdrom-image"
From the documentation it appears the following is true:
- cdrom-image = Provides the ISO to the VM
- atapi-cdrom = Provides a NEC emulated ATAPI CD-ROM on top of the host
CD-ROM
- cdrom-raw = Passthru for a host CD-ROM drive. Allows CD-R burning from
within the guest.
A CD-ROM prior to this patch would always provide an 'atapi-cdrom' is
modeled as:
<disk type='block' device='cdrom'>
<source dev='/dev/scd0'/>
<target dev='hda' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
This patch allows the 'device' attribute to be set to 'lun' for a raw
acccess CD-ROM such as:
<disk type='block' device='lun'>
<source dev='/dev/scd0'/>
<target dev='hda' bus='ide'/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
This corresponds to '-sd' and '-drive if=sd' on the qemu command line.
Needed for many ARM boards which don't provide any other way to
pass in storage.
Add an attribute named 'removable' to the 'target' element of disks,
which controls the removable flag. For instance, on a Linux guest it
controls the value of /sys/block/$dev/removable. This option is only
valid for USB disks (i.e. bus='usb'), and its default value is 'off',
which is the same behaviour as before.
To achieve this, 'removable=on' (or 'off') is appended to the '-device
usb-storage' parameter sent to qemu when adding a USB disk via
'-disk'. A capability flag QEMU_CAPS_USB_STORAGE_REMOVABLE was added
to keep track if this option is supported by the qemu version used.
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=922495
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
'make distcheck' was failing with:
make[3]: Entering directory `/home/eblake/libvirt-tmp2/libvirt-1.1.1/_build/docs'
perl ../../docs/genaclperms.pl ../../src/access/viraccessperm.h > ../../docs/aclperms.htmlinc
/bin/sh: ../../docs/aclperms.htmlinc: Permission denied
when simulating the case of a user doing a VPATH build from a
read-only source tree. The culprit? BUILT_SOURCES are _always_
built, and so must NOT be built into srcdir and need not be part
of the tarball. On the other hand, shipped files must never
depend on files in the builddir. While it would be possible to
fix the problem by generating aclperms.htmlinc into builddir,
we then have the problem that we ship acl.html - we'd have to
rejigger a lot of things to not ship pre-built html. So this
patch goes the other direction - we don't need BUILT_SOURCES,
but instead ensure that we have proper dependencies so that
all files in srcdir are up-to-date at the time the tarball is
created. And because we ship html files in the tarball, that
implies we don't expect users to be able to rebuild them, so
we must not clean any files that would trigger a rebuild except
under the maintainer rules.
* docs/Makefile.am (BUILT_SOURCES): Delete.
(CLEANFILES): Downgrade aclperms.htmlinc cleanup...
(maintainer-clean-local): ...and move hvsupport.html.in...
(MAINTAINERCLEANFILES): ...to a maintainer action.
(hvsupport.html.in): Write into srcdir.
(hvsupport.html): Ensure files are built in order.
(aclperms.htmlinc): Honor silent make.
(EXTRA_DIST): Ship aclperms.htmlinc.
Signed-off-by: Eric Blake <eblake@redhat.com>
With the 1.1.1 tarball, if a user does 'make && make distcheck',
things pass, but if they do 'make distcheck' after 'make clean',
there is an odd failure:
GEN ../../docs/devhelp/index.html
I/O error : Permission denied
I/O error : Permission denied
runtime error: file ../../docs/devhelp/devhelp.xsl line 43 element document
xsltDocumentElem: unable to save to ../../docs/devhelp/libvirt-virterror.html
I/O error : Permission denied
I/O error : Permission denied
This implies that the rules for 'make dist' are missing a
dependency - the generated documentation needs to be up-to-date
before creating the tarball, or else the tarball will be missing
files, where the end user will end up trying to rebuild files in
srcdir, and that fails when srcdir is read-only.
1.1.1 plus this patch now works without issues (other issues have
crept in to 1.1.2-rc1 that prevent 'make distcheck' from working,
but those will be cleaned up in later patches).
* docs/Makefile.am (dist-local): New dependency.
Signed-off-by: Eric Blake <eblake@redhat.com>
<controller type='pci' index='0' model='pci-root'>
<pcihole64 unit='KiB'>1048576</pcihole64>
</controller>
It can be used to adjust (or disable) the size of the 64-bit
PCI hole. The size attribute is in kilobytes (different unit
can be specified on input), but it gets rounded up to
the nearest GB by QEMU.
Disabling it will be needed for guests that crash with the
64-bit PCI hole (like Windows XP), see:
https://bugzilla.redhat.com/show_bug.cgi?id=990418
The ftp protocol is already recognized by qemu/KVM so add this support to
libvirt as well.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='ftp' name='/url/path'>
<host name='host.name' port='21'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
QEMU/KVM already allows a HTTP URL for the cdrom ISO image so add this support
to libvirt as well.
The xml should be as following:
<disk type='network' device='cdrom'>
<source protocol='http' name='/url/path'>
<host name='host.name' port='80'/>
</source>
</disk>
Signed-off-by: Aline Manera <alinefm@br.ibm.com>
Consistently use "is" or "is not" to compare variables to None,
because doing so is preferrable, as per PEP 8
(http://www.python.org/dev/peps/pep-0008/#programming-recommendations):
> Comparisons to singletons like None should always be done with is or
> is not, never the equality operators.
Add more iSCSI examples including having a secret attached. There are 4 new
examples; one for each way to have an iSCSI - a network disk using virtio,
a passthrough network lun using scsi, a volume disk using "mode='host'",
and a volume disk using "mode='direct'"
https://bugzilla.redhat.com/show_bug.cgi?id=924153
Commit 904e05a2 (v0.9.9) added a per-<disk> seclabel element with
an attribute relabel='no' in order to try and minimize the
impact of shutdown delays when an NFS server disappears. The idea
was that if a disk is on NFS and can't be labeled in the first
place, there is no need to attempt the (no-op) relabel on domain
shutdown. Unfortunately, the way this was implemented was by
modifying the domain XML so that the optimization would survive
libvirtd restart, but in a way that is indistinguishable from an
explicit user setting. Furthermore, once the setting is turned
on, libvirt avoids attempts at labeling, even for operations like
snapshot or blockcopy where the chain is being extended or pivoted
onto non-NFS, where SELinux labeling is once again possible. As
a result, it was impossible to do a blockcopy to pivot from an
NFS image file onto a local file.
The solution is to separate the semantics of a chain that must
not be labeled (which the user can set even on persistent domains)
vs. the optimization of not attempting a relabel on cleanup (a
live-only annotation), and using only the user's explicit notation
rather than the optimization as the decision on whether to skip
a label attempt in the first place. When upgrading an older
libvirtd to a newer, an NFS volume will still attempt the relabel;
but as the avoidance of a relabel was only an optimization, this
shouldn't cause any problems.
In the ideal future, libvirt will eventually have XML describing
EVERY file in the backing chain, with each file having a separate
<seclabel> element. At that point, libvirt will be able to track
more closely which files need a relabel attempt at shutdown. But
until we reach that point, the single <seclabel> for the entire
<disk> chain is treated as a hint - when a chain has only one
file, then we know it is accurate; but if the chain has more than
one file, we have to attempt relabel in spite of the attribute,
in case part of the chain is local and SELinux mattered for that
portion of the chain.
* src/conf/domain_conf.h (_virSecurityDeviceLabelDef): Add new
member.
* src/conf/domain_conf.c (virSecurityDeviceLabelDefParseXML):
Parse it, for live images only.
(virSecurityDeviceLabelDefFormat): Output it.
(virDomainDiskDefParseXML, virDomainChrSourceDefParseXML)
(virDomainDiskSourceDefFormat, virDomainChrDefFormat)
(virDomainDiskDefFormat): Pass flags on through.
* src/security/security_selinux.c
(virSecuritySELinuxRestoreSecurityImageLabelInt): Honor labelskip
when possible.
(virSecuritySELinuxSetSecurityFileLabel): Set labelskip, not
norelabel, if labeling fails.
(virSecuritySELinuxSetFileconHelper): Fix indentation.
* docs/formatdomain.html.in (seclabel): Document new xml.
* docs/schemas/domaincommon.rng (devSeclabel): Allow it in RNG.
* tests/qemuxml2argvdata/qemuxml2argv-seclabel-*-labelskip.xml:
* tests/qemuxml2argvdata/qemuxml2argv-seclabel-*-labelskip.args:
* tests/qemuxml2xmloutdata/qemuxml2xmlout-seclabel-*-labelskip.xml:
New test files.
* tests/qemuxml2argvtest.c (mymain): Run the new tests.
* tests/qemuxml2xmltest.c (mymain): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
In one of my previous patches I am removing the hard_limit heuristic to
guess the correct value if none set. However, it turned out, this limit
is hard to guess even for users. We should advise them to not set the
limit as their domains may be OOM killed. Sigh.
Feedback from the polkit developers indicates that the
"_detail_XXXX" attributes are a private implementation
detail. Our examples should be recommending use of the
"action.lookup('XXX')" method instead.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This resolves the issue that prompted the filing of
https://bugzilla.redhat.com/show_bug.cgi?id=928638
(although the request there is for something much larger and more
general than this patch).
commit f3868259ca disabled the
forwarding to upstream DNS servers of unresolved DNS requests for
names that had no domain, but were just simple host names (no "."
character anywhere in the name). While this behavior is frowned upon
by DNS root servers (that's why it was changed in libvirt), it is
convenient in some cases, and since dnsmasq can be configured to allow
it, it must not be strictly forbidden.
This patch restores the old behavior, but since it is usually
undesirable, restoring it requires specification of a new option in
the network config. Adding the attribute "forwardPlainNames='yes'" to
the <dns> elemnt does the trick - when that attribute is added to a
network config, any simple hostnames that can't be resolved by the
network's dnsmasq instance will be forwarded to the DNS servers listed
in the host's /etc/resolv.conf for an attempt at resolution (just as
any FQDN would be forwarded).
When that attribute *isn't* specified, unresolved simple names will
*not* be forwarded to the upstream DNS server - this is the default
behavior.
The description for <permissions> was copied from the storage volume
section to the storage pool section, but the semantics are different:
1. Currently only the "dir", "fs" and "netfs" storage pools use it.
2. They use it only to build the final directory.
3. A default for the storage volumes can't be set.
Signed-off-by: Philipp Hahn <hahn@univention.de>
Commit ab92ae333 added a cool feature, but didn't document it.
* docs/hacking.html.in: Document debugging a subset of tests.
* HACKING: Regenerate.
Signed-off-by: Eric Blake <eblake@redhat.com>
Add to the docs/drvlxc.html.in documentation to describe how to
configure systemd to auto-activate a container when a client
connects to a socket
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The gnulib testsuite is relatively stable - the only times it is
likely to have a test change from pass to fail is on a gnulib
submodule update or a major system change (such as moving from
Fedora 18 to 19, or other large change to libc). While it is an
important test for end users on arbitrary machines (to make sure
that the portability glue works for their machine), it mostly
wastes time for development testing (as most developers aren't
making any of the major changes that would cause gnulib tests
to alter behavior). Thus, it pays to make the tests optional
at configure time, defaulting to off for development, on for
tarballs, with autobuilders requesting it to be on. It also
helps to allow a make-time override, via VIR_TEST_EXPENSIVE=[01]
(much the way automake sets up V=[01] for overriding the configure
time default of how verbose to be).
Automake has some pretty hard-coded magic with regards to the
TESTS variable; I had quite a job figuring out how to keep
'make distcheck' passing regardless of the configure option
setting in use, while still disabling the tests at runtime
when I did not configure them on and did not use the override
variable. Thankfully, we require GNU make, which lets me
hide some information from Automake's magic handling of TESTS.
* bootstrap.conf (bootstrap_epilogue): Munge gnulib test variable.
* configure.ac (--enable-expensive-tests): Add new enable switch.
(VIR_TEST_EXPENSIVE_DEFAULT, WITH_EXPENSIVE_TESTS): Set new
witnesses.
* gnulib/tests/Makefile.am (TESTS): Make tests conditional on
configure settings and the VIR_TEST_EXPENSIVE variable.
* tests/Makefile.am (TESTS_ENVIRONMENT): Expose VIR_TEST_EXPENSIVE
to all tests.
* autobuild.sh: Enable all tests during autobuilds.
* libvirt.spec.in (%configure): Likewise.
* mingw-libvirt.spec.in (%mingw_configure): Likewise.
* docs/hacking.html.in: Document the option.
* HACKING: Regenerate.
Signed-off-by: Eric Blake <eblake@redhat.com>
This adds two new pages to the website, acl.html describing
the general access control framework and permissions models,
and aclpolkit.html describing the use of polkit as an
access control driver.
page.xsl is modified to support a new syntax
<div id="include" filename="somefile.htmlinc"/>
which will cause the XSL transform to replace that <div>
with the contents of 'somefile.htmlinc'. We use this in
the acl.html.in file, to pull the table of permissions
for each libvirt object. This table is autogenerated
from the enums in src/access/viraccessperms.h by the
genaclperms.pl script.
newapi.xsl is modified so that the list of permissions
checks shown against each API will link to the description
of the permissions in acl.html
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
So that app developers / admins know what access control checks
are performed for each API, this patch extends the API docs
generator to include details of the ACLs for each.
The gendispatch.pl script is extended so that it generates
a simple XML describing ACL rules, eg.
<aclinfo>
...
<api name='virConnectNumOfDomains'>
<check object='connect' perm='search_domains'/>
<filter object='domain' perm='getattr'/>
</api>
<api name='virDomainAttachDeviceFlags'>
<check object='domain' perm='write'/>
<check object='domain' perm='save' flags='!VIR_DOMAIN_AFFECT_CONFIG|VIR_DOMAIN_AFFECT_LIVE'/>
<check object='domain' perm='save' flags='VIR_DOMAIN_AFFECT_CONFIG'/>
</api>
...
</aclinfo>
The newapi.xsl template loads the XML files containing the ACL
rules and generates a short block of HTML for each API describing
the parameter checks and return value filters (if any).
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This PCI controller, named "dmi-to-pci-bridge" in the libvirt config,
and implemented with qemu's "i82801b11-bridge" device, connects to a
PCI Express slot (e.g. one of the slots provided by the pcie-root
controller, aka "pcie.0" on the qemu commandline), and provides 31
*non-hot-pluggable* PCI (*not* PCIe) slots, numbered 1-31.
Any time a machine is defined which has a pcie-root controller
(i.e. any q35-based machinetype), libvirt will automatically add a
dmi-to-pci-bridge controller if one doesn't exist, and also add a
pci-bridge controller. The reasoning here is that any useful domain
will have either an immediate (startup time) or eventual (subsequent
hot-plug) need for a standard PCI slot; since the pcie-root controller
only provides PCIe slots, we need to connect a dmi-to-pci-bridge
controller to it in order to get a non-hot-plug PCI slot that we can
then use to connect a pci-bridge - the slots provided by the
pci-bridge will be both standard PCI and hot-pluggable.
Since pci-bridge devices themselves can not be hot-plugged into a
running system (although you can hot-plug other devices into a
pci-bridge's slots), any new pci-bridge controller that is added can
(and will) be plugged into the dmi-to-pci-bridge as long as it has
empty slots available.
This patch is also changing the qemuxml2xml-pcie test from a "DO_TEST"
to a "DO_DIFFERENT_TEST". This is so that the "before" xml can omit
the automatically added dmi-to-pci-bridge and pci-bridge devices, and
the "after" xml can include it - this way we are testing if libvirt is
properly adding these devices.
This controller is implicit on q35 machinetypes. It provides 31 PCIe
(*not* PCI) slots as controller 0.
Currently there are no devices that can connect to pcie-root, and no
implicit pci controller on a q35 machine, so q35 is still
unusable. For a usable q35 system, we need to add a
"dmi-to-pci-bridge" pci controller, which can connect to pcie-root,
and provides standard pci slots that can be used to connect other
devices.
The outbound/@peak is ignored (since QoS was introduced). This is due to
kernel limitation of know allowing ingress filters to have peak just
average rate. However, we should document this limitation to not confuse
users.
Interestingly, we had <code>floor<code> ... </code>outbound</code> which
results in much larger block of text to be written in code style that
intended.
There are two ways to use a iSCSI LUN as disk source for qemu.
* The LUN's path as it shows up on host, e.g.
/dev/disk/by-path/ip-$ip:3260-iscsi-$iqn-fc18:iscsi.iscsi0-lun-1
* The libiscsi URI from the storage pool source element host attribute, e.g.
iscsi://demo.org:6000/iqn.1992-01.com.example/1
For a "volume" type disk, if the specified "pool" is of iscsi
type, we should support to use the LUN in either of above 2 ways.
That's why to introduce a new XML tag "mode" for the disk source
(libvirt should support iscsi pool with libiscsi, but it's another
new feature, which should be done later).
The "mode" can be either of "host" or "direct". Use "host" to indicate
use of the LUN with the path as it shows up on host. Use "direct" to
indicate to use it with the source pool host URI (future patches may support
to use network type libvirt storage too, e.g. Ceph)
Makefiles are another easy file to enforce line limits.
Mostly straightforward; interesting tricks worth noting:
src/Makefile.am: $(confdir) was already defined, use it in more places
tests/Makefile.am: path_add and VG required some interesting compression
* cfg.mk (sc_prohibit_long_lines): Add another test.
* Makefile.am: Fix offenders.
* daemon/Makefile.am: Likewise.
* docs/Makefile.am: Likewise.
* python/Makefile.am: Likewise.
* src/Makefile.am: Likewise.
* tests/Makefile.am: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
