To ensure that the device addressing scheme is stable across
hotplug/unplug, all virtio serial channels needs to have an
associated port number in their address. This is then specified
to QEMU using the nr=NNN parameter
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parsing
for port number in vioserial address types.
* src/qemu/qemu_conf.c: Set 'nr=NNN' parameter with virtio
serial port number
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: Expand
data set to ensure coverage of port addressing
'listen' isn't a valid qemu-dm option, as reported a long time ago here:
https://bugzilla.redhat.com/show_bug.cgi?id=492958
Matches the near identical logic in qemu_conf.c
v2: When parsing sexpr, only match on ",server", rather than
full ',server,nowait'.
* tests/daemon-conf: Accommodate the fact that out template,
daemon/libvirtd.conf now contains an invalid host_uuid.
Convert it to a valid one before the final libvirtd-running
test that must terminate normally.
This patch parses the following two XML descriptions, one for
802.1Qbg and one for 802.1Qbh, and stores the data internally.
The actual triggering of the switch setup protocol has not been
implemented here but the relevant code to do that should go into
the functions associatePortProfileId() and disassociatePortProfileId().
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbg'>
<parameters managerid='12' typeid='0x123456' typeidversion='1'
instanceid='fa9b7fff-b0a0-4893-8e0e-beef4ff18f8f'/>
</virtualport>
<filterref filter='clean-traffic'/>
</interface>
<interface type='direct'>
<source dev='eth0.100' mode='vepa'/>
<model type='virtio'/>
<virtualport type='802.1Qbh'>
<parameters profileid='my_profile'/>
</virtualport>
</interface>
I'd suggest to use this patch as a base for triggering the setup
protocol with the 802.1Qb{g|h} switch.
Several rounds of changes were made to this patch. The
following is a list of these changes.
- Renamed structure virVirtualPortProfileDef to virVirtualPortProfileParams
as per Daniel Berrange's request
- Addressing Daniel Berrange's comments:
- removing macvtap.h's dependency on domain_conf.h by
moving the virVirtualPortProfileDef structure into macvtap.h
and not passing virtDomainNetDefPtr to any functions in
macvtap.c
- Addressed most of Chris Wright's comments:
- indicating error in case virtualport XML node cannot be parsed
properly
- parsing hex and decimal numbers using virStrToLong_ui() with
parameter '0' for base
- tgifname (target interface name) variable wasn't necessary
to pass to openMacvtapTap function anymore
- assigning the virtual port data structure to the virDomainNetDef
only if it was previously parsed
- make sure that the error code returned by openMacvtapTap() is a negative n
in case the associatePortProfileId() function failed.
- renaming vsi in the XML to virtualport
- replace all occurrences of vsi in the source as well
- removing mode and MAC address parameters from the functions that
will communicate with the hareware diretctly or indirectly
- moving the associate and disassociate functions to the end of the
file for subsequent patches to easier make them generally available
for export
- passing the macvtap interface name rather than the link device since
this otherwise gives funny side effects when using netlink messages
where IFLA_IFNAME and IFLA_ADDRESS are specified and the link dev
all of a sudden gets the MAC address of the macvtap interface.
- Removing rc = -1 error indications in the case of 802.1Qbg|h setup in case
we wanted to use hook scripts for the setup and so the setup doesn't fail
here.
- if instance ID UUID is not supplied it will automatically be generated
- adapted schema to make instance ID UUID optional
- added test case
- parser and XML generator have been separated into their own
functions so they can be re-used elsewhere (passthrough case
for example)
- Adapted XML parser and generator support the above shown type
(802.1Qbg, 802.1Qbh).
- Adapted schema to above XML
- Adapted test XML to above XML
- Passing through the VM's UUID which seems to be necessary for
802.1Qbh -- sorry no host UUID
- adding virtual function ID to association function, in case it's
necessary to use (for SR-IOV)
Spurious / in a pool target path makes life difficult for apps using the
GetVolByPath, and doing other path based comparisons with pools. This
has caused a few issues for virt-manager users:
https://bugzilla.redhat.com/show_bug.cgi?id=494005https://bugzilla.redhat.com/show_bug.cgi?id=593565
Add a new util API which removes spurious /, virFileSanitizePath. Sanitize
target paths when parsing pool XML, and for paths passed to GetVolByPath.
v2: Leading // must be preserved, properly sanitize path=/, sanitize
away /./ -> /
v3: Properly handle starting ./ and ending /.
v4: Drop all '.' handling, just sanitize / for now.
Allow for a host UUID in the capabilities XML. Local drivers
will initialize this from the SMBIOS data. If a sanity check
shows SMBIOS uuid is invalid, allow an override from the
libvirtd.conf configuration file
* daemon/libvirtd.c, daemon/libvirtd.conf: Support a host_uuid
configuration option
* docs/schemas/capability.rng: Add optional host uuid field
* src/conf/capabilities.c, src/conf/capabilities.h: Include
host UUID in XML
* src/libvirt_private.syms: Export new uuid.h functions
* src/lxc/lxc_conf.c, src/qemu/qemu_driver.c,
src/uml/uml_conf.c: Set host UUID in capabilities
* src/util/uuid.c, src/util/uuid.h: Support for host UUIDs
* src/node_device/node_device_udev.c: Use the host UUID functions
* tests/confdata/libvirtd.conf, tests/confdata/libvirtd.out: Add
new host_uuid config option to test
* tests/nodeinfotest.c (linuxTestCompareFiles): Don't use
nodeinfo->member uninitialized. linuxNodeInfoCPUPopulate requires
that some of its nodeinfo members (including threads) be initialized
upon input. The nodeinfotest.c program lacked the initialization,
while the only other use (nodeGetInfo) did perform it.
It's not trivial to move the initialization into the function,
since nodeGetInfo sets at least one member after clearing the
buffer but before calling linuxNodeInfoCPUPopulate.
(gdb) p/x QEMUD_CMD_FLAG_VNET_HOST
$7 = 0xffffffff80000000
Oops - that meant we were incorrectly setting QEMU_CMD_FLAG_RTC_TD_HACK
for qemu-kvm-0.12.3 (and probably botching a few other settings as well).
Fixes Red Hat BZ#592070
* src/qemu/qemu_conf.h (QEMUD_CMD_FLAG_VNET_HOST): Avoid sign
extension.
* tests/qemuhelpdata/qemu-kvm-0.12.3: New file.
* tests/qemuhelptest.c (mymain): Add another case.
The max path length for unix sockets is pretty small (108, see man 7 unix).
If 'make check' is run from a directory that exceeds this, one of the tests
will fail, and in such a way that requires manually editting the test to
determine why.
There are certainly other ways to handle this, but I've chosen just to skip
the offending test if we will exceed the length limitation.
v2: Drop bashism, use test infrastructure to warn and skip
* tests/virsh-schedinfo: This test sets PATH internally, just in
case you're running it manually. Normally, the PATH setting from
tests/Makefile.am's TESTS_ENVIRONMENT is sufficient. Prepend the
correct directory, and take advantage of the PATH setting in one
more case.
For example, virsh -c test:///default schedinfo 1 --set P=k would
mistakenly exit successfully, giving no indication that it had failed
to set the scheduling parameter "P".
* tools/virsh.c (cmdSchedinfo): Diagnose an invalid --set j=k option,
rather than silently ignoring it.
* tests/virsh-schedinfo: New test for the above.
* tests/Makefile.am (test_scripts): Add it.
Reported by Jintao Yang in http://bugzilla.redhat.com/586632
This patch adds support for the RARP protocol. This may be needed due to
qemu sending out a RARP packet (at least that's what it seems to want to
do even though the protocol id is wrong) when migration finishes and
we'd need a rule to let the packets pass.
Unfortunately my installation of ebtables does not understand -p RARP
and also seems to otherwise depend on strings in /etc/ethertype
translated to protocol identifiers. Therefore I need to pass -p 0x8035
for RARP. To generally get rid of the dependency of that file I switch
all so far supported protocols to use their protocol identifier in the
-p parameter rather than the string.
I am also extending the schema and added a test case.
changes from v1 to v2:
- added test case into patch
* virStorageEncryptionFormat is called from both
virDomainDiskDefFormat and virStorageVolTargetDefFormat. The proper
indentation in the generated XML depends on the caller. My earlier
patch to fix the incorrect indentation for the domain XML broke the
indentation for the storage XML. This patch adopts Laine's
suggestion of requring the caller of virStorageEncryptionFormat to
provide an unsigned int with the number of spaces the output should
be indented. The patch modifies both callers to provide the
additional argument.
* Add a regression test for the domain XML
* src/conf/domain_conf.c src/conf/storage_conf.c
src/conf/storage_encryption_conf.c src/conf/storage_encryption_conf.h:
change the indentation code
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-encrypted-disk.args
tests/qemuxml2argvdata/qemuxml2argv-encrypted-disk.xml: add a regression test
With this patch I want to enable hex number inputs in the filter XML. A
number that was entered as hex is also printed as hex unless a string
representing the meaning can be found.
I am also extending the schema and adding a test case. A problem with
the DSCP value is fixed on the way as well.
Changes from V1 to V2:
- using asHex boolean in all printf type of functions to select the
output format in hex or decimal format
The nodeinfotest was reliant on the host NUMA topology, but all
the test data files assumed 1 single NUMA node. This test thus
failed on any NUMA machine with > 1 node
* tests/nodeinfotest.c: Hardcode 1 single numa node
Fix invalid code generating in esx_vi_generator.py regarding deep copy
types that contain enum properties.
Add strptime and timegm to bootstrap.conf. Both are used to convert a
xsd:dateTime to calendar time.
Add a testcase of the xsd:dateTime conversion.
Extend tests to cover all SCSI controller types and document the
new type.
The lsisas1068 SCSI controller type was added in ESX 4.0. The VMX
parser reports an error when this controller type is present. This
makes virsh dumpxml fail for every domain that uses this controller
type.
This patch fixes this and adds lsisas1068 to the list of accepted
SCSI controller types.
Reported by Jonathan Kelley.
This patch implements support for learning a VM's IP address. It uses
the pcap library to listen on the VM's backend network interface (tap)
or the physical ethernet device (macvtap) and tries to capture packets
with source or destination MAC address of the VM and learn from DHCP
Offers, ARP traffic, or first-sent IPv4 packet what the IP address of
the VM's interface is. This then allows to instantiate the network
traffic filtering rules without the user having to provide the IP
parameter somewhere in the filter description or in the interface
description as a parameter. This only supports to detect the parameter
IP, which is for the assumed single IPv4 address of a VM. There is not
support for interfaces that may have multiple IP addresses (IP
aliasing) or IPv6 that may then require more than one valid IP address
to be detected. A VM can have multiple independent interfaces that each
uses a different IP address and in that case it will be attempted to
detect each one of the address independently.
So, when for example an interface description in the domain XML has
looked like this up to now:
<interface type='bridge'>
<source bridge='mybridge'/>
<model type='virtio'/>
<filterref filter='clean-traffic'>
<parameter name='IP' value='10.2.3.4'/>
</filterref>
</interface>
you may omit the IP parameter:
<interface type='bridge'>
<source bridge='mybridge'/>
<model type='virtio'/>
<filterref filter='clean-traffic'/>
</interface>
Internally I am walking the 'tree' of a VM's referenced network filters
and determine with the given variables which variables are missing. Now,
the above IP parameter may be missing and this causes a libvirt-internal
thread to be started that uses the pcap library's API to listen to the
backend interface (in case of macvtap to the physical interface) in an
attempt to determine the missing IP parameter. If the backend interface
disappears the thread terminates assuming the VM was brought down. In
case of a macvtap device a timeout is being used to wait for packets
from the given VM (filtering by VM's interface MAC address). If the VM's
macvtap device disappeared the thread also terminates. In all other
cases it tries to determine the IP address of the VM and will then apply
the rules late on the given interface, which would have happened
immediately if the IP parameter had been explicitly given. In case an
error happens while the firewall rules are applied, the VM's backend
interface is 'down'ed preventing it to communicate. Reasons for failure
for applying the network firewall rules may that an ebtables/iptables
command failes or OOM errors. Essentially the same failure reasons may
occur as when the firewall rules are applied immediately on VM start,
except that due to the late application of the filtering rules the VM
now is already running and cannot be hindered anymore from starting.
Bringing down the whole VM would probably be considered too drastic.
While a VM's IP address is attempted to be determined only limited
updates to network filters are allowed. In particular it is prevented
that filters are modified in such a way that they would introduce new
variables.
A caveat: The algorithm does not know which one is the appropriate IP
address of a VM. If the VM spoofs an IP address in its first ARP traffic
or IPv4 packets its filtering rules will be instantiated for this IP
address, thus 'locking' it to the found IP address. So, it's still
'safer' to explicitly provide the IP address of a VM's interface in the
filter description if it is known beforehand.
* configure.ac: detect libpcap
* libvirt.spec.in: require libpcap[-devel] if qemu is built
* src/internal.h: add the new ATTRIBUTE_PACKED define
* src/Makefile.am src/libvirt_private.syms: add the new modules and symbols
* src/nwfilter/nwfilter_learnipaddr.[ch]: new module being added
* src/nwfilter/nwfilter_driver.c src/conf/nwfilter_conf.[ch]
src/nwfilter/nwfilter_ebiptables_driver.[ch]
src/nwfilter/nwfilter_gentech_driver.[ch]: plu the new functionality in
* tests/nwfilterxml2xmltest: extend testing
This patch adds a relaxng nwfilter schema along with a test that
verifies all the test output XML against the schema. The input XMLs
contain a lot of intentional out-of-range values that make them fail the
schema verification, so I am not verifying against those.
A lot of syntax check rules have to be rewritten, but the
result is easier to maintain. I tested each syntax rule
by intentionally introducing a temporary violation of the rule.
Additionally, some false positives for unmarked_diagnostics
crept in, and an improved copyright_format test caught some bugs.
* .gnulib: Update to latest.
* cfg.mk (sc_prohibit_test_minus_ao): Delete, it was moved into
gnulib's maint.mk.
(sc_avoid_write, sc_prohibit_strcmp_and_strncmp)
(sc_prohibit_asprintf, sc_prohibit_strncpy, sc_prohibit_readlink)
(sc_prohibit_gethostname, sc_prohibit_gettext_noop)
(sc_prohibit_VIR_ERR_NO_MEMORY, sc_prohibit_nonreentrant)
(sc_prohibit_ctype_h, sc_TAB_in_indentation)
(sc_avoid_ctype_macros)
(sc_prohibit_virBufferAdd_with_string_literal)
(sc_prohibit_gethostby, sc_copyright_format): Rewrite in terms of
new maint.mk macros.
(sc_libvirt_unmarked_diagnostics): Fix whitespace.
* .x-sc_unmarked_diagnostics: New file.
* tests/object-locking.ml: Fix copyright.
* tools/virt-pki-validate.in: Likewise.
* tools/virt-xml-validate.in: Likewise.
* src/qemu/qemu_conf.h: define 4 new flags
* src/qemu/qemu_conf.c: check the help text of qemu for presence of
features indicated by each flag.
* tests/qemuhelptest.c: add appropriate flags into the masks for each test
* Fixes per feedback from Dan and Daniel
* Added test datafiles
* Re-disabled JSON flags
* Added code to print the error policy attribute when generating XML
* Re-add empty tag
The keys of entries in a VMX file are case insensitive. Both scsi0:1.fileName
and scsi0:1.filename are valid. Therefore, make the conf parser compare names
case insensitive in VMX mode to accept every capitalization variation.
Also add test cases for this.
* tests/test-lib.sh: "echo -n" is not portable. Use printf instead.
Remove unnecessary uses of "eval-in-subshell" (subshell is sufficient).
Remove uses of tests' -a operator; it is not portable.
Instead, use "test cond && test cond2".
* tests/schematestutils.sh: Replace use of test's -a.
This change only affects the output of tests that have an exact
multiple of 40 test cases. For example the domainschematest currently:
TEST: domainschematest
........................................ 40
........................................ 80
........................................ 120
........................................ 160
........................................ 200 OK
PASS: domainschematest
It outputs additional 40 spaces on the last line.
The domainschematest output is fixed by the change in test-lib.sh. The
change in testutils.c fixes this for tests written in C. Currently no
C test has an exact multiple of 40 test cases, but I checked it and
the same problem exists there.
This patch stops that in both cases.
* src/qemu/qemu_conf.c: add the ",readonly=on" for read-only disks
and also parse it back in qemuParseCommandLineDisk()
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.args
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-readonly-disk.xml:
add a specific regression test
The current code for "nodeinfo" is pretty naive
about socket and thread information. To determine the
sockets, it just takes the number of cpus and divides
by the number of cores. For the thread count, it always
sets it to 1. With more recent Intel machines, however,
hyperthreading is again an option, meaning that these
heuristics no longer work and give bogus numbers. This
patch goes through /sys to get the additional
information so we properly report it.
Note that I had to edit the tests not to report on
socket and thread counts, since these are determined
dynamically now.
v2: As pointed out by Eric Blake, gnulib provides
count-one-bits (which is LGPLv2+). Use it instead
of a hand-coded popcnt.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Allow an arbitrary timezone with QEMU by setting the $TZ environment
variable when launching QEMU
* src/qemu/qemu_conf.c: Set TZ environment variable if a timezone
is requested
* tests/qemuxml2argvtest.c: Add test case for timezones
* tests/qemuxml2argvdata/qemuxml2argv-clock-france.xml,
tests/qemuxml2argvdata/qemuxml2argv-clock-france.args: Data
for timezone tests
This allows QEMU guests to be started with an arbitrary clock
offset
The test case can't actually be enabled, since QEMU argv expects
an absolute timestring, and this will obviously change every
time the test runs :-( Hopefully QEMU will allow a relative
time offset in the future.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Use the -rtc arg
if available to support variable clock offset mode
* tests/qemuhelptest.c: Add QEMUD_CMD_FLAG_RTC for qemu 0.12.1
* qemuxml2argvdata/qemuxml2argv-clock-variable.args,
qemuxml2argvdata/qemuxml2argv-clock-variable.xml,
qemuxml2argvtest.c: Test case, except we can't actually enable
it yet.
The daemon-conf test would fail on my system if there was a system libvirtd
running. In the course of troubleshooting that problem, I discovered that the
daemon-conf script would always fail if run by itself because it found the line:
\# that each "PARAMETER = VALUE" line in this file have the parameter
which it mistook for a line containing a parameter. I have changed the test to
avoid mistaking a line containing \"PARAMETER = VALUE\" for a parameter line.
The corrupted config tests turned out to be failing because the test daemon was
discovering the pid file from the running daemon and exiting before it processed
the test config file. Specifying the pid file for the corrupt config tests in
the same way as for the valid config test solved that problem.
Support virtio-serial controller and virtio channel in QEMU backend.
Will output
the following for virtio-serial controller:
-device
virtio-serial-pci,id=virtio-serial0,bus=pci.0,addr=0x4,max_ports=16,vectors=4
and the following for a virtio channel:
-chardev pty,id=channel0 \
-device
virtserialport,bus=virtio-serial0.0,chardev=channel0,name=org.linux-kvm.port.0
* src/qemu/qemu_conf.c: Add argument output for virtio
* tests/qemuxml2argvtest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args: Add test for
QEMU command line generation
Add support for virtio-serial by defining a new 'virtio' channel target type
and a virtio-serial controller. Allows the following to be specified in a
domain:
<controller type='virtio-serial' index='0' ports='16' vectors='4'/>
<channel type='pty'>
<target type='virtio' name='org.linux-kvm.port.0'/>
<address type='virtio-serial' controller='0' bus='0'/>
</channel>
* docs/schemas/domain.rng: Add virtio-serial controller and virtio
channel type.
* src/conf/domain_conf.[ch]: Domain parsing/serialization for
virtio-serial controller and virtio channel.
* tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.xml: add domain xml
parsing test
* src/libvirt_private.syms src/qemu/qemu_conf.c:
virDomainDefAddDiskControllers() renamed to
virDomainDefAddImplicitControllers()
Use the ATTRIBUTE_NONNULL annotation to mark some virConnectPtr
args as mandatory non-null so the compiler can warn of mistakes
* src/conf/domain_event.h: All virConnectPtr args must be non-null
* src/qemu/qemu_conf.h: qemudBuildCommandLine and
qemudNetworkIfaceConnect() must be given non-null connection
* tests/qemuxml2argvtest.c: Provide a non-null (dummy) connection to
qemudBuildCommandLine()
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in interface_conf.{h,c} and update all callers to
match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in storage_conf.{h,c} and storage_encryption_conf.{h,c}
and update all callers to match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in node_device_conf.{h,c} and update all callers to
match
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in network_conf.{h,c} and update all callers to
match
The QEMU flags are commonly stored as a signed or unsigned int,
allowing only 31 flags. This limit is rather close, so to aid
future patches, change it to a 64-bit int
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c,
tests/qemuargv2xmltest.c, tests/qemuhelptest.c, tests/qemuxml2argvtest.c:
Use 'unsigned long long' for QEMU flags
To allow devices to be hot(un-)plugged it is neccessary to ensure
they all have a unique device aliases. This fixes the hotplug
methods to assign device aliases before invoking the monitor
commands which need them
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Expose methods
for assigning device aliases for disks, host devices and
controllers
* src/qemu/qemu_driver.c: Assign device aliases when hotplugging
all types of device
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address-device.args:
Update for changed hostdev naming scheme
The current way of assigning names to the host network backend and
NIC device in QEMU was over complicated, by varying naming scheme
based on the NIC model and backend type. This simplifies the naming
to simply be 'net0' and 'hostnet0', allowing code to easily determine
the host network name and vlan based off the primary device alias
name 'net0'. This in turn allows removal of alot of QEMU specific
code from the XML parser, and makes it easier to assign new unique
names for NICs that are hotplugged
* src/conf/domain_conf.c, src/conf/domain_conf.h: Remove hostnet_name
and vlan fields from virNetworkDefPtr
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c:
Use a single network alias naming scheme regardless of NIC type
or backend type. Determine VLANs from the alias name.
* tests/qemuxml2argvdata/qemuxml2argv-net-eth-names.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args: Update
for new simpler naming scheme
The QEMU 0.12.x tree has the -netdev command line argument, but not
corresponding monitor command. We can't enable the former, without
the latter since it will break hotplug/unplug.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Disable -netdev usage
until 0.13 at earliest
* tests/qemuxml2argvtest.c: Add test for -netdev syntax
* tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.xml: Test
data files for -netdev syntax
The current QEMU code allocates PCI addresses incrementally starting
at 4. This is not satisfactory because the user may have given some
addresses in their XML config, which need to be skipped over when
allocating addresses to remaining devices.
It is thus neccessary to maintain a list of already allocated PCI
addresses and then only allocate ones that remain unused. This is
also required for domain device hotplug to work properly later.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Add APIs for creating
list of existing PCI addresses, and allocating new addresses.
Refactor address assignment to use this code
* src/qemu/qemu_driver.c: Pull PCI address assignment up into the
qemuStartVMDaemon() method, as a prelude to moving it into the
'define' method. Update list of allocated addresses when connecting
to a running VM at daemon startup.
* tests/qemuxml2argvtest.c, tests/qemuargv2xmltest.c,
tests/qemuxml2xmltest.c: Remove USB product test since all
passthrough is done based on address
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.xml: Kil
unused data files
The test expected all environment variables copied in qemudBuildCommandLine
to have known values. So all of them have to be either set to a known value
or be unset. SDL_VIDEODRIVER and QEMU_AUDIO_DRV are not handled at all but
should be handled. Unset both, otherwise the test will fail if they are set
in the testing environment.
* src/qemu/qemu_conf.c: add a comment about copied environment variables
and qemuxml2argvtest
* tests/qemuxml2argvtest.c: unset SDL_VIDEODRIVER and QEMU_AUDIO_DRV
The RNG now supports IPv6 and bonds attached to bridges, along with
some other minor tweaks. All test files from netcf have been copied to
the test directory and added to the xml2xml and schema tests (and they
all pass, of course ;-)
QEMU's command line equivalent for the following domain XML fragment
<vcpus>2</vcpus>
<cpu ...>
...
<topology sockets='1' cores='2', threads='1'/>
</cpu>
is
-smp 2,sockets=1,cores=2,threads=1
This syntax was introduced in QEMU-0.12.
Version 2 changes:
- -smp argument build split into a separate function
- always add ",sockets=S,cores=C,threads=T" to -smp if qemu supports it
- use qemuParseCommandLineKeywords for command line parsing
Version 3 changes:
- ADD_ARG_LIT => ADD_ARG and line reordering in qemudBuildCommandLine
- rebased
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Replace
-balloon virtio
With
-device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3
This allows it to get correct assigned PCI address as declared in
previous patch
* src/qemu/qemu_conf.c: Convert Virtio ballon to -device and
give it an explicit PCI address
* tests/qemuxml2argvdata/qemuxml2argv-*args: Add in virtio balloon
where appropriate
Instead of relying on QEMU to assign PCI addresses and then querying
them with 'info pci', manually assign all PCI addresses before starting
the guest. These addresses are not stable across reboots. That will
come in a later patch
NB, the PIIX3 (IDE, FDC, ISA-Bridge) will always have slot 1 and
VGA will always have slot 2. We declare the Virtio Balloon gets
slot 3, and then all remaining slots are for configured devices.
* src/qemu/qemu_conf.c: If -device is supported, then assign all PCI
addresses when building the command line
* src/qemu/qemu_driver.c: Don't query monitor for PCI addresses if
they have already been assigned
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-sound-device.args,
tests/qemuxml2argvdata/qemuxml2argv-watchdog-device.args: Update
to include PCI slot/bus information
QEMU always configures a VGA card. If no video card is included in
the libvirt XML, it is neccessary to explicitly turn off the default
using -vga none
* src/qemu/qemu_conf.c: Pass -vga none if no video card is configured
* tests/qemuargv2xmltest.c, tests/qemuxml2argvtest.c: Test for
handling -vga none.
* tests/qemuxml2argvdata/qemuxml2argv-nographics-vga.args,
tests/qemuxml2argvdata/qemuxml2argv-nographics-vga.xml: Test
data files
Not all QEMU builds default to SDL graphics for their display.
Newer QEMU now has an explicit -sdl flag, which we can use to
explicitly request SDL intead of relying on the default. This
protects libvirt against unexpected changes in graphics default
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Probe for -sdl
flag and use it if it is found
* tests/qemuhelptest.c: Add SDL flag to tests
The old syntax was
-chardev SOMECONFIG
-nic user,guestfwd=tcp:IP:PORT-chardev:CHARDEV
The new syntax is
-chardev SOMECONFIG
-netdev user,guestfwd=tcp:IP:PORT,chardev=ID,id=user-ID
The old syntax was
-usbdevice host:PRODUCT:VENDOR
Or
-usbdevice host:BUS.DEV
The new syntax is
-device usb-host,product=PRODUCT,vendor=VENDOR
Or
-device usb-host,hostbus=BUS,hostaddr=DEV
The previous syntax was severely limited in its options
-usbdevice disk:/home/berrange/output.img
The new syntax is the same as for other disk types
-drive file=/home/berrange/output.img,if=none,id=usb-1,index=1
-device usb-storage,drive=usb-1
Again, the index= arg is wrong here, and will be removed in a
later merge
The current syntax uses a pair of args
-net nic,macaddr=52:54:00:56:6c:55,vlan=3,model=pcnet,name=pcnet.0
-net user,vlan=3,name=user.0
The new syntax does not need the vlan craziness anymore, and
so has a simplified pair of args
-netdev user,id=user.0
-device pcnet,netdev=user.0,id=pcnet.0,mac=52:54:00:56:6c:55,addr=<PCI SLOT>
The current syntax for audio devices is a horrible multiplexed
arg
-soundhw sb16,pcspk,ac97
The new syntax is
-device sb16,id=sound0
or
-device AC97,id=sound1,addr=<PCI SLOT>
NB, pcspk still uses the old -soundhw syntax
The current character device syntax uses either
-serial tty,path=/dev/ttyS2
Or
-chardev tty,id=serial0,path=/dev/ttyS2 -serial chardev:serial0
With the new -device support, we now prefer
-chardev file,id=serial0,path=/tmp/serial.log -device isa-serial,chardev=serial0
This patch changes the existing -chardev syntax to use this new
scheme, and fallbacks to the old plain -serial syntax for old
QEMU.
The monitor device changes to
-chardev socket,id=monitor,path=/tmp/test-monitor,server,nowait -mon chardev=monitor
In addition, this patch adds --nodefaults, which kills off the
default serial, parallel, vga and nic devices. THis avoids the
need for us to explicitly turn each off
Probe for the new -device flag and if available set the -nodefaults
flag, instead of using -net none, -serial none or -parallel none.
Other device types will be converted to use -device in later patches.
The -nodefaults flag will help avoid unwelcome surprises from future
QEMU releases
* src/qemu/qemu_conf.c: Probe for -device. Add -nodefaults flag.
Remove -net none, -serial none or -parallel none
* src/qemu/qemu_conf.h: Define QEMU_CMD_FLAG_DEVICE
* tests/qemuhelpdata/qemu-0.12.1: New data file for 0.12.1 QEMU
* tests/qemuhelptest.c: Test feature extraction from 0.12.1 QEMU
Existing applications using libvirt are not aware of the disk
controller concept. Thus, after parsing the <disk> definitions
in the XML, it is neccessary to create <controller> elements
to satisfy all requested disks, as per their defined drive
addresses
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/libvirt_private.syms: Add virDomainDefAddDiskControllers()
method for populating disk controllers, and call it after
parsing disk definitions.
* src/qemu/qemu_conf.c: Call virDomainDefAddDiskControllers()
when doing ARGV -> XML conversion
* tests/qemuxml2argvdata/qemuxml2argv*.xml: Add disk controller
data to all data files which don't have it already
It is perfectly acceptable to have multiple sound devices of
same type in guest configuration. If the underlying hypervisor
does not like this, it is its job to complain, not the XML
parser's
* src/conf/domain_conf.c: Remove hack which deleted duplicated
sound device models.
* tests/xml2sexprdata/xml2sexpr-fv-sound.xml: Remove duplicate
models
The latter is not officially "wrong", but *is* terribly anachronistic.
I think automake documentation or comments call that syntax obsolescent.
* cfg.mk (_makefile_at_at_check_exceptions): Exempt @SCHEMADIR@
and @SYSCONFDIR@ uses -- there are no Makefile variables for those.
* docs/Makefile.am: Use $(INSTALL), not @INSTALL@.
* examples/dominfo/Makefile.am: Similar.
* examples/domsuspend/Makefile.am: Similar.
* proxy/Makefile.am: Similar.
* python/Makefile.am: Similar.
* python/tests/Makefile.am: Similar.
* src/Makefile.am: Similar.
* tests/Makefile.am: Similar.
* src/conf/domain_conf.c: add defaults for the video device
* src/esx/esx_vmx.[ch]: add VNC support to the VMX handling
* tests/vmx2xmltest.c, tests/xml2vmxtest.c: add tests for the VNC support
The current code for using -drive simply sets the -drive 'index'
parameter. QEMU internally converts this to bus/unit depending
on the type of drive. This does not give us precise control over
the bus/unit assignment though. This change switches over to make
libvirt explicitly calculate the bus/unit number.
In addition bus/unit/index are actually irrelevant for VirtIO
disks, since each virtio disk is a separate PCI device. No disk
controller is involved.
Doing the conversion to bus/unit in libvirt allows us to correctly
attach SCSI controllers when required.
* src/qemu/qemu_conf.c: Specify bus/unit instead of index for
disks
* tests/qemuxml2argvdata/qemuxml2argv-disk*.args: Switch over from
using index=NNNN, to bus=NN, unit=NN for SCSI/IDE/Floppy disks
When parsing the <disk> element specification, if no <address>
is provided for the disk, then automatically assign one based on
the <target dev='sdXX'/> device name. This provides for backwards
compatability with existing applications using libvirt, while also
allowing new apps to have complete fine grained control.
* src/conf/domain_conf.h, src/conf/domain_conf.c,
src/libvirt_private.syms: Add virDomainDiskDefAssignAddress()
for assigning a controller/bus/unit address based on disk target
* src/qemu/qemu_conf.c: Call virDomainDiskDefAssignAddress() after
generating XML from ARGV
* tests/qemuxml2argvdata/*.xml: Add in drive address information
to all XML files
Only print out '.' for each test case, full test output can be
re-enabled with VIR_TEST_VERBOSE=1, or VIR_TEST_DEBUG=XXXX
Sample output now looks like
TEST: statstest
........................................ 40
................................... 75 OK
PASS: statstest
TEST: qparamtest
................................ 32 OK
PASS: qparamtest
TEST:
............ 12 OK
The MAC addresses with 00:50:56 prefix are split into several ranges:
00:50:56:00:00:00 - 00:50:56:3f:ff:ff 'static' range (manually assigned)
00:50:56:80:00:00 - 00:50:56:bf:ff:ff 'vpx' range (assigned by a VI Client)
Erroneously the 'vpx' range was assumed to be larger and to occupy the
remaining addresses of the 00:50:56 prefix that are not part of the 'static'
range.
00:50:56 was used as prefix for generated MAC addresses, this is not possible
anymore, because there are gaps in the allowed ranges. Therefore, change the
prefix to 00:0c:29 which is the prefix for auto generated MAC addresses anyway.
Allow arbitrary MAC addresses to be used and set the checkMACAddress VMX option
to false in case the MAC address doesn't fall into any predefined range.
* docs/drvesx.html.in: update website accordingly
* src/esx/esx_driver.c: set the auto generation prefix to 00:0c:29
* src/esx/esx_vmx.c: fix MAC address range handling and allow arbitrary MAC
addresses
* tests/vmx2xml*, tests/xml2vmx*: add some basic MAC address range tests
The behavior for the qemu balloon device has changed. Formerly, a virtio
balloon device was provided by default. Now, '-balloon virtio' must be
specified on the command line to enable it. This patch causes libvirt to
add '-balloon virtio' to the command line whenever the -balloon option is
available.
* src/qemu/qemu_conf.c src/qemu/qemu_conf.h: check for the new flag and
add "-baloon vitio" to qemu command when needed
* tests/qemuhelptest.c: add the new flag for detection
tests/virt-aa-helper-test and examples/apparmor are not included in
official tarballs, but should be. Attached is a patch to fix that
which works when apparmor is and is not available.
Change -monitor, -serial and -parallel output to use -chardev if it is
available.
* src/qemu/qemu_conf.c: Update qemudBuildCommandLine to use -chardev where
available.
* tests/qemuxml2argvtest.c tests/qemuxml2argvdata/: Add -chardev equivalents
for all current serial and parallel tests.
Initial support for the new QEMU monitor protocol using JSON
as the data encoding format instead of plain text
* po/POTFILES.in: Add src/qemu/qemu_monitor_json.c
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Hack to turn on QMP
mode. Replace with a version number check on >= 0.12 later
* src/qemu/qemu_monitor.c: Delegate to json monitor if enabled
* src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h: Add
impl of QMP protocol
* src/Makefile.am: Add src/qemu/qemu_monitor_json.{c,h}
esxVMX_IndexToDiskName handles indices up to 701. This limit comes
from a mapping gap in virDiskNameToIndex:
sdzy -> 700
sdzz -> 701
sdaaa -> 728
sdaab -> 729
This line in virDiskNameToIndex causes this gap:
idx = (idx + i) * 26;
Fixing it by altering this line to:
idx = (idx + (i < 1 ? 0 : 1)) * 26;
Also add a new version of virIndexToDiskName that handles the inverse
mapping for arbitrary indices.
* src/esx/esx_vmx.[ch]: remove esxVMX_IndexToDiskName
* src/util/util.[ch]: add virIndexToDiskName and fix mapping gap
* tests/esxutilstest.c: update test to verify that the gap is fixed
Introduce a new type="dir" mode for <disks> that allows use of
QEMU's virtual FAT block device driver. eg
<disk type='dir' device='floppy'>
<source dir='/tmp/test'/>
<target dev='fda' bus='fdc'/>
<readonly/>
</disk>
gets turned into
-drive file=fat:floppy:/tmp/test,if=floppy,index=0
Only read-only disks are supported with virtual FAT mode
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add type="dir"
* docs/schemas/domain.rng: Document new disk type
* src/xen/xend_internal.c, src/xen/xm_internal.c: Raise error for
unsupported disk types
* tests/qemuxml2argvdata/qemuxml2argv-disk-cdrom-empty.args: Fix
empty disk file handling
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.xml,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.xml
tests/qemuxml2argvtest.c: Test QEMU vitual FAT driver
* src/qemu/qemu_conf.c: Support generating fat:/some/dir type
disk args
* src/security/security_selinux.c: Temporarily skip labelling
of directory based disks
Recent qemu releases require command option '-enable-qemu' in order
for the kvm functionality be activated. Libvirt needs to pass this flag
to qemu when starting a domain. Note that without the option,
even if both the kernel and qemu support KVM, KVM will not be activated
and VMs will be very slow.
* src/qemu/qemu_conf.h src/qemu/qemu_conf.c: parse the extra command
line option from help and add it when running kvm
* tests/qemuhelptest.c: this modified the flags output for qemu-0.10.5
and qemu-kvm-0.11.0-rc2 regression tests
VMware uses two MAC address prefixes: 00:0c:29 and 00:50:56. The 00:0c:29
prefix is used for ESX server generated addresses. The 00:50:56 prefix is
split into two parts. MAC addresses above 00:50:56:3f:ff:ff are generated
by a vCenter. The rest of the 00:50:56 prefix can be assigned manually.
Any MAC address within the 00:0c:29 and 00:50:56 prefix can be specified
in a domain XML config and the driver will handle the details internally.
* src/esx/esx_vmx.c: fix MAC address formatting
* tests/xml2vmxdata/*: update test files accordingly
* src/security/virt-aa-helper.c: get_definition() now calls the new
caps_mockup() function which will parse the XML for os.type,
os.type.arch and then sets the wordsize. These attributes are needed
only to get a valid virCapsPtr for virDomainDefParseString(). The -H
and -b options are now removed from virt-aa-helper (they weren't used
yet anyway).
* tests/virt-aa-helper-test: extend and fixes tests, chmod'ed 755
allows the following to be specified in a domain:
<channel type='pipe'>
<source path='/tmp/guestfwd'/>
<target type='guestfwd' address='10.0.2.1' port='4600'/>
</channel>
* proxy/Makefile.am: add network.c as dep of domain_conf.c
* docs/schemas/domain.rng src/conf/domain_conf.[ch]: extend the domain
schemas and the parsing/serialization side for the new construct
QEmu support will add the following on the qemu command line:
-chardev pipe,id=channel0,path=/tmp/guestfwd
-net user,guestfwd=tcp:10.0.2.1:4600-chardev:channel0
* src/qemu/qemu_conf.c: Add argument output for channel
* tests/qemuxml2(argv|xml)test.c: Add test for <channel> domain syntax
- Don't duplicate SystemError
- Use proper error code in domain_conf
- Fix a broken error call in qemu_conf
- Don't use VIR_ERR_ERROR in security driver (isn't a valid code in this case)
Nearly all of the methods in src/util/util.h have error codes that
must be checked by the caller to correct detect & report failure.
Add ATTRIBUTE_RETURN_CHECK to ensure compile time validation of
this
* daemon/libvirtd.c: Add explicit check on return value of virAsprintf
* src/conf/domain_conf.c: Add missing check on virParseMacAddr return
value status & report error
* src/network/bridge_driver.c: Add missing OOM check on virAsprintf
and report error
* src/qemu/qemu_conf.c: Add missing check on virParseMacAddr return
value status & report error
* src/security/security_selinux.c: Remove call to virRandomInitialize
that's done in libvirt.c already
* src/storage/storage_backend_logical.c: Add check & log on virRun
return status
* src/util/util.c: Add missing checks on virAsprintf/Run status
* src/util/util.h: Annotate all methods with ATTRIBUTE_RETURN_CHECK
if they return an error status code
* src/vbox/vbox_tmpl.c: Add missing check on virParseMacAddr
* src/xen/xm_internal.c: Add missing checks on virAsprintf
* tests/qemuargv2xmltest.c: Remove bogus call to virRandomInitialize()
This patch adds an optional attribute to the <bootp> tag, that
allows to specify a TFTP server address other than the address of
the DHCP server itself.
This can be used to forward the BOOTP settings of the host down to the
guest. This is something that configurations such as Xen's default
network achieve naturally, but must be done manually for NAT.
* docs/formatnetwork.html.in: Document new attribute.
* docs/schemas/network.rng: Add it to schema.
* src/conf/network_conf.h: Add it to struct.
* src/conf/network_conf.c: Add it to parser and pretty printer.
* src/network/bridge_driver.c: Put it in the dnsmasq command line.
* tests/networkxml2xmlin/netboot-proxy-network.xml
tests/networkxml2xmlout/netboot-proxy-network.xml
tests/networkxml2xmltest.c: add new tests
Provide a simple interface for other tests to lookup the testDebug variable.
Also remove a redundant error message in interface tests.
If anyone feels inclined to change this env variable to match the existing
LIBVIRT_* format, it should now be easier to do so.
If one has e.g.
<guest>
<os_type>hvm</os_type>
<arch name='x86_64'>
<wordsize>64</wordsize>
<emulator>/usr/bin/qemu-system-x86_64</emulator>
<machine>pc-0.11</machine>
<machine canonical='pc-0.11'>pc</machine>
<machine>pc-0.10</machine>
<machine>isapc</machine>
<domain type='qemu'>
</domain>
<domain type='kvm'>
<emulator>/usr/bin/kvm</emulator>
<machine>pc</machine>
<machine>isapc</machine>
</domain>
</arch>
</guest>
and start a guest with:
<domain type='kvm'>
...
<os>
<type arch='x86_64'>hvm</type>
...
</os>
</domain>
then the default machine type should be 'pc' and not 'pc-0.11'
Issue was reported by Anton Protopopov.
* src/capabilities.[ch]: pass the domain type to
virCapabilitiesDefaultGuestArch() and use it to look up the default
machine type from a specific guest domain if needed.
* src/conf/domain_conf.c, src/xen/xm_internal.c: update
* tests/qemuxml2argvdata/qemuxml2argv-machine-aliases2.xml: update
the domain type to 'kvm' and remove the machine type to check
that the default gets looked up correctly
* configure.in: look for AppArmor and devel
* src/security/security_apparmor.[ch] src/security/security_driver.c
src/Makefile.am: add and plug the new driver
* src/security/virt-aa-helper.c: new binary which is used exclusively by
the AppArmor security driver to manipulate AppArmor.
* po/POTFILES.in: registers the new files
* tests/Makefile.am tests/secaatest.c tests/virt-aa-helper-test:
tests for virt-aa-helper and the security driver, secaatest.c is
identical to seclabeltest.c except it initializes the 'apparmor'
driver instead of 'selinux'
While running make check, I noticed that it was actually using
the virsh binary from my system, in /usr/bin/virsh, and not the
one that was just compiled. This is actually caused by a bug
in Makefile.am, where we didn't update the PATH to include tools.
While here, I also updated all of the scripts to properly define
the srcdir, abs_top_srcdir, and abs_top_builddir environment
variables. This is required if you want to be able to run the
tests standalone (i.e. ./test instead of from make check). I've
tested this on both RHEL-5 and Fedora-10 machines, and make check
works on both, as does running the individual tests by hand.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
A given domain XML gets converted to a VMX config, uploaded to the host
and registered as new virtual machine.
* src/esx/esx_driver.c: refactor datastore related path parsing into
esxUtil_ParseDatastoreRelatedPath()
* src/esx/esx_util.[ch]: add esxUtil_ParseDatastoreRelatedPath()
* src/esx/esx_vi.[ch]: add esxVI_Context_UploadFile(), add datastores to
the traversal in esxVI_BuildFullTraversalSpecList(), add
esxVI_LookupDatastoreByName()
* src/esx/esx_vi_methods.[ch]: add esxVI_RegisterVM_Task()
* src/esx/esx_vi_types.c: make some error message more verbose
* src/esx/esx_vmx.[ch]: add esxVMX_AbsolutePathToDatastoreRelatedPath()
to convert a path into a datastore related path, add esxVMX_ParseFileName()
to convert from VMX path format to domain XML path format, extend the other
parsing function to be datastore aware, add esxVMX_FormatFileName() to
convert from domain XML path format to VMX path format, fix VMX ethernet
entry formating
* tests/esxutilstest.c: add test for esxUtil_ParseDatastoreRelatedPath()
* tests/vmx2xmldata/*: update domain XML files to use datastore related paths
* tests/xml2vmxdata/*: update domain XML files to use datastore related paths,
update VMX files to use absolute paths
* tests/.gitignore: ignore new test binaries
* tests/Makefile.am: add new tests
* tests/esxutilstest.c: test esxVMX_IndexToDiskName()
* tests/vmx2xmldata/*: config files for the VMX to domain XML test
* tests/vmx2xmltest.c: test the VMX to domain XML mapping
* tests/xml2vmxdata/*: config files for the domain XML to VMX test
* tests/xml2vmxtest.c: test the domain XML to VMX mapping
Currently, libvirtd will start a dnsmasq process for the virtual
network, but (aside from killing the dnsmasq process and replacing it),
there's no way to define tftp boot options.
This change introduces the appropriate tags to the dhcp configuration:
<network>
<name>default</name>
<bridge name="virbr%d" />
<forward/>
<ip address="192.168.122.1" netmask="255.255.255.0">
<tftp root="/var/lib/tftproot" />
<dhcp>
<range start="192.168.122.2" end="192.168.122.254" />
<bootp file="pxeboot.img"/>
</dhcp>
</ip>
</network>
When the attributes are present, these are passed to the
arguments to dnsmasq:
dnsmasq [...] --enable-tftp --tftp-root /srv/tftp --dhcp-boot pxeboot.img
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^^
from <tftp /> from <bootp />
At present, only local tftp servers are supported (ie, dnsmasq runs as
the tftp server), but we could improve this in future by adding a
server= attribute.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2009-09-21 Paolo Bonzini <pbonzini@redhat.com>
Jeremy Kerr <jk@ozlabs.org>
* docs/formatnetwork.html.in: Document new tags.
* docs/formatnetwork.html: Regenerate.
* docs/schemas/network.rng: Update.
* src/network_conf.c (virNetworkDefFree): Free new fields.
(virNetworkDHCPRangeDefParseXML): Parse <bootp>.
(virNetworkIPParseXML): New, parsing <dhcp> and <tftp>.
(virNetworkDefParseXML): Use virNetworkIPParseXML instead of
virNetworkDHCPRangeDefParseXML.
(virNetworkDefFormat): Pretty print new fields.
* src/network_conf.h (struct _virNetworkDef): Add netboot fields.
* src/network_driver.c (networkBuildDnsmasqArgv): Add
TFTP and BOOTP arguments.
* tests/Makefile.am (EXTRA_DIST): Add networkschemadata.
* tests/networkschematest: Look in networkschemadata.
* tests/networkschemadata/netboot-network.xml: New.
Latest upstream QEMU can be built with Xen support, which introduces
a -xen-domid argument. This was mistakenly detected as -domid due
to old Xenner support. Adapt to cope with both syntax. Also only
set domid if the virt type is xen, or the guest type is xen
* src/qemu_conf.c, src/qemu_conf.h: Detect new -xen-domid flag in
preference to -domid.
* tests/qemuxml2argvdata/qemuxml2argv-bootloader.args,
tests/qemuxml2argvdata/qemuxml2argv-input-xen.args: Add missing
-domid param
* tests/qemuxml2argvdata/qemuxml2argv-misc-uuid.args: Remove bogus
-boot param.
* tests/qemuxml2argvtest.c: Add missing QEMUD_CMD_FLAG_DOMID params
* docs/storage/: Move to examples/xml/storage/
* docs/test*.xml: Move to examples/xml/test/
* docs/Makefile.am: Remove example XML files from dist
* Makefile.am: Add examples/xml to EXTRA_DIST
* tests/virshtest.c: Update for moved test XML
* libvirt.spec.in: Include example XML files as docs
* tests/int-overflow: UPdate for moved XML
* src/capabilities.c, src/capabilities.h, src/domain_conf.c,
src/domain_conf.h, src/domain_event.c, src/domain_event.h,
src/interface_conf.c, src/interface_conf.h,
src/network_conf.c, src/network_conf.h, src/node_device_conf.c,
src/node_device_conf.h, src/secret_conf.c, src/secret_conf.h,
src/storage_conf.c, src/storage_conf.h, src/storage_encryption_conf.c,
src/storage_encryption_conf.h: Move to src/conf/
* src/Makefile.am: Add -Isrc/conf to the individual build targets
which need to use XML config APIs. Remove LIBXML_CFLAGS, LIBSSH2_CFLAGS
and SELINUX_CFLAGS from global INCLUDES and only have them in build
targets which actually need them. Create a libvirt_conf.la
convenience library for all config parsers
* src/hostusb.h: Remove bogus include of domain_conf.h
* tests/Makefile.am: Add -Isrc/conf. Remove bogus -I$builddir/src
since it never has any generated header files
* daemon/Makefile.am: Add -Isrc/conf
* proxy/Makefile.am: Add -Isrc/conf and cope with renamed files
* src/hash.c: Remove bogus include of libxml/threads.h
* daemon/default-network.xml: Move to src/network/default.xml
* daemon/libvirtd_qemu.aug, daemon/test_libvirtd_qemu.aug: Move
to src/qemu/
* src/qemu.conf: Move to src/qemu/qemu.conf
* daemon/Makefile.am: Remove rules for default-nmetwork.xml and
libvirtd_qemu.aug and test_libvirtd_qemu.aug. Fix typo in
uninstall-local that would install polkit again.
* src/Makefile.am: Add rules for installing network/default.xml
and the qemu/*.aug files. Add test case for QEMU augeas files.
Add uninstall-local rule for files/directories created during
install. Rename install-exec-local to install-data-local.
Only install qemu.conf if WITH_QEMU is set.
* tests/networkschematest: Update for XML location move
Move the virsh tool and its man page into the tools directory
* Makefile.am: Remove rules for virsh.1 man page
* virsh.1: Remove auto-generated file
* docs/Makefile.am: Remove rules for virsh.pod man page
* docs/virsh.pod: Move to tools/ directory
* src/Makefile.am, src/.gitignore: Remove rules for virsh
* src/console.c, src/console.h, src/*.ico, src/virsh_win_icon.rc,
src/virsh.c: Move into tools/ directory
* tools/Makefile.am: Add rules for building virsh
* tools/.gitignore: Ignore virsh built files
* tests/virshtest.c, tests/int-overflow: Update for new
virsh location
Fix all thread locking bugs reported by object-locking test
case.
NB, some of the driver locking is getting too coarse. Driver
mutexes really need to be turned into RW locks instead to
significantly increase concurrency.
* src/lxc_driver.c: Fix useof driver when unlocked in the methods
lxcDomainGetInfo, lxcSetSchedulerParameters, and
lxcGetSchedulerParameters
* src/opennebula/one_driver.c: Fix missing unlock in oneDomainUndefine.
Fix use of driver when unlocked in oneDomainGetInfo,
oneGetOSType, oneDomainShutdown
* src/qemu_driver.c: Fix use of driver when unlocked in
qemudDomainSavem, qemuGetSchedulerType, qemuSetSchedulerParameters
and qemuGetSchedulerParameters
* src/storage_driver.c: Re-work storagePoolCreate to avoid bogus
lock checking warning. Re-work storageVolumeCreateXMLFrom to
remove a potential NULL de-reference & avoid bogus lock check
warnings
* src/test.c: Remove testDomainAssignDef since it break lock chekc
warnings.
* tests/object-locking.ml: Add oneDriverLock, oneDriverUnlock
and one_driver_t methods/types to allow lock checking on the
OpenNebula drivers
* tests/testutilsqemu.c: add a machine types list for /usr/bin/kvm
which doesn't have any aliases, while the guest has aliases
* tests/qemuxml2argvdata/qemuxml2argv-machine-aliases2.*,
tests/qemuxml2argvtest.c: add a test using /usr/bin/kvm and make
sure that 'pc' machine type doesn't get canonicalized using the
aliases in the guest machine type list
* tests/testutilsqemu.c: make 'pc' an alias for qemu-system-x86_64
* tests/qemuxml2argvdata/qemuxml2argv-machine-aliases1.*,
tests/qemuxml2argvtest.c: add a test which uses qemu-system-x86_64
and make sure the machine type is canonicalized.
This doesn't have any affect on the current tests because we don't have
any machine aliases in the current test data.
* src/qemu_conf.h, src/qemu_driver.c: expose qemudCanonicalizeMachine()
for the tests
* tests/qemuxml2argvtest.c: canonicalize the machine type
Things added include
- x86_64 host
- Migration features
- NUMA topology
- Security model
- Canonical machine types
- Domain machine types
- An arm guest
- More machine types for mips, mipsel, sparc and ppc
- An x86_64 xenner guest
This file was generated on a Fedora 12 machine using latest libvirt
and qemu-kvm-0.11.0-rc2
* tests/capabilityschemadata/caps-qemu-kvm.xml: add more features
to test
If a file descriptor with events=0 was added to the libvirtd
event loop, it would still be added to the poll() fds' array.
While it wouldn't see any POLLIN/OUT events, it'd still get
triggered for HANGUP/ERROR events which was not in compliance
with the libvirt events API contract.
* qemud/event.c: Don't poll on FDs with events=0
* tests/eventtest.c: Add test case to validate fix to event.c
* docs/schemas/domain.rng: Add <serial> element to disks
* src/domain_conf.h, src/domain_conf.c: XML parsing and
formatting for disk serial numbers
* src/qemu_conf.c: Set serial number when launching guests
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-shared.args,
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-shared.xml: Add
serial number to XML test
Add option to domain XML for
<memoryBacking>
<hugepages/>
</memoryBacking>
* configure.in: Add check for mntent.h
* qemud/libvirtd_qemu.aug, qemud/test_libvirtd_qemu.aug, src/qemu.conf
Add 'hugetlbfs_mount' config parameter
* src/qemu_conf.c, src/qemu_conf.h: Check for -mem-path flag in QEMU,
and pass it when hugepages are requested.
Load hugetlbfs_mount config parameter, search for mount if not given.
* src/qemu_driver.c: Free hugetlbfs_mount/path parameter in driver shutdown.
Create directory for QEMU hugepage usage, chowning if required.
* docs/formatdomain.html.in: Document memoryBacking/hugepages elements
* docs/schemas/domain.rng: Add memoryBacking/hugepages elements to schema
* src/util.c, src/util.h, src/libvirt_private.syms: Add virFileFindMountPoint
helper API
* tests/qemuhelptest.c: Add -mem-path constants
* tests/qemuxml2argvtest.c, tests/qemuxml2xmltest.c: Add tests for hugepage
handling
* tests/qemuxml2argvdata/qemuxml2argv-hugepages.xml,
tests/qemuxml2argvdata/qemuxml2argv-hugepages.args: Data files for
hugepage tests
* tests/testutils.c: Run test function twice, once to prime it for
static allocations, once to count the non-static allocations.
* tests/testutilsqemu.c: Initialize variable correctl
* src/capabilities.c: Don't free machines variable upon failure
since caller must do that
* src/xm_internal.c: Add missing check for OOM in building VIF
config param
Calling qsort() on the disks array causes disk to be
unneccessarily re-ordered, potentially breaking the
ability to boot if the boot disk gets moved later in
the list. The new algorithm will insert a new disk as
far to the end of the list as possible, while being
ordered correctly wrt other disks on the same bus.
* src/domain_conf.c, src/domain_conf.h: Remove disk sorting
routines. Add API to insert a disk into existing list at
the optimal position, without resorting disks
* src/libvirt_private.syms: Export virDomainDiskInsert
* src/xend_internal.c, src/xm_internal.c: Remove calls to
qsort, use virDomainDiskInsert instead.
* src/qemu_driver.c: Remove calls to qsort, use virDoaminDiskInsert
instead. Fix reordering bugs when hotunplugging disks and
networks. Fix memory leak in disk/net unplug
The XML allows <encryption format='unencrypted'/>, this implementation
canonicalizes the internal representation so that "vol->encryption" is
non-NULL iff the volume is encrypted.
Note that partial encryption information (e.g. specifying an encryption
format, but not the key/passphrase) is valid, libvirt will automatically
choose value for the missing information during volume creation. The
user can read the volume XML, and use the unmodified <encryption> tag in
future operations (without having to be able to understand) its contents.
* docs/formatstorage.html, docs/formatstorage.html.in: Document
storage volume encryption options
* src/storage_conf.c, src/storage_conf.h: Hook up storage
encryption XML handling
* tests/storagevolschemadata/vol-qcow2.xml: Test case for encryption
schema changes
Test case for the fix applied in
commit 14435163a0
Author: Daniel Veillard <veillard@redhat.com>
Date: Fri Jun 26 18:14:16 2009 +0000
* tests/sexpr2xmldata/sexpr2xml-pv-vfb-type-crash.sexpr,
tests/sexpr2xmldata/sexpr2xml-pv-vfb-type-crash.xml: Data
files exhibiting the crash
* tests/sexpr2xmltest.c: Process new data files
PCI device assignment is only supported in KVM's fork of qemu, so we
should really detect its availability and give a nice error if its
not supported.
* src/qemu_conf.[ch]: introduce QEMUD_CMD_FLAG_PCIDEVICE indicating
that the -pcidevice command line option is available
* tests/*: update the tests
* src/logging.c src/logging.h src/libvirt_private.syms:
define new functions virLogSetFromEnv and virLogParseDefaultPriority
* qemud/qemud.c src/libvirt.c tests/eventtest.c: cleanup to use the
unified functions
A subsequent commit will add a "canonical" field to this structure,
this patch basically just prepares the way for that.
The new type is added, along with virCapabilitiesAlloc/FreeMachines()
helpers and a whole bunch of code to make the transition.
One quirk is that virCapabilitiesAddGuestDomain() and
virCapabilitiesAddGuest() take ownership of the machine list rather
than duping it. This makes sense to avoid needless copying.
* src/capabilities.h: add the virCapsGuestMachine struct and use it
in virCapsGuestDomainInfo, add prototypes for new functions and
update the AddGuest() prototypes
* src/capabilities.c: add code for allocating and freeing the new
type, change the machines parameter to AddGuest() etc.
* src/libvirt_private.syms: export the new helpers
* src/qemu_conf.c: update all the machine type code to use the new
struct
* src/xen_internal.c: ditto
* tests/testutilsqemu.c: ditto
We need these so that we can remove the devices via the monitor.
* src/domain_conf.h: add nic_name and hostnet_name to virDomainNetDef
* src/domain_conf.c: free nic_name and hostnet_name
* src/qemu_conf.c: add qemuAssignNetNames(), use it if qemu has
support for the param and pass the names on the command line
* tests/qemuxml2argv*: add a test for this
Add QEMUD_CMD_FLAG_NET_NAME to indicate that '-net ...,name=foo' is
supported and QEMUD_CMD_FLAG_HOST_NET_ADD to indicate that the
'host_net_add' monitor command is available.
Set both these flags if the qemu version is greater than 0.10.0.
Checking via the '-help' output would not work for the monitor command
and even for the command line arg, it would be quite fragile.
* src/qemu_conf.h: add new flags as aliases of QEMUD_CMD_FLAG_0_10
* src/qemu_conf.c: set QEMUD_CMD_FLAG_0_10 for versions >= 0.10.0
* tests/qemuhelptest.c: set QEMUD_CMD_FLAG_0_10 for the appropriate
qemu versions
by running this command:
git ls-files -z | xargs -0 perl -pi -0777 -e 's/\n\n+$/\n/'
This is in preparation for a more strict make syntax-check
rule that will detect trailing blank lines.
* tests/interfaceschematest: test all XML data against the interface
schemas
* tests/interfacexml2xmltest.c: parse and reserialize all XML data
and check the output is identical
* tests/Makefile.am: hook up the tests
* tests/.gitignore: add ignore test
* docs/schemas/interface.rng: schemas for the interface XML files
directly imported from netcf-0.1.0
* tests/interfaceschemadata/*.xml: set of test files from netcf-0.1.0
changed to use single quote instead of double quote
We keep support for the pty based monitor so that we can re-connect
to VMs started by older versions of libvirtd.
* src/domain_conf.c: handle formatting and parsing unix monitors
* src/qemu_driver.c: add qemudOpenMonitorUnix(), remove the monitor
pty path searching from qemudFindCharDevicePTYs(), switch
qemudStartVMDaemon() and qemuDomainXMLToNative() to using a unix
monitor
* tests/qemuxml2argvtest.c: switch to using a unix monitor
* tests/qemuxml2argvdata/qemuxml2argv-*.args: update test data
There are no functional changes in this patch apart from adding the
monitor type to the state XML.
The patch mostly consists of switching to use virDomainChrDef every
where to describe the monitor.
* src/domain_conf.h: replace monitorpath with monitor_chr
* src/domain_conf.c: handle parsing the monitor type and initializing
monitor chr
* src/qemu_conf.[ch]: make qemudBuildCommandLine take a
virDomainChrDefPtr and use that to build the -monitor parameter
* src/qemu_driver.c: split pty specific and common code from
qemudOpenMonitor, have qemudStartVMDaemon() initialize monitor_chr
* tests/qemuxml2argvtest.c: update for qemudBuildCommandLine() change
It failed in a non-srcdir build because those 5 sample output
files were not included in the distribution tarball. Include them.
* tests/Makefile.am (qemuhelpdata, EXTRA_DIST): Include these:
kvm-74, kvm-86, qemu-0.10.5, qemu-0.9.1, qemu-kvm-0.10.5.
* src/qemu_conf.c, src/qemu_conf.h: Use -vga or -std-vga
when starting guests if video card is present
* tests/qemuhelptest.c: Change to use constants instead
of hardcoded hex numbers, and add VGA support
* tests/qemuxml2argvdata/qemuxml2argv-graphics-sdl-fullscreen.xml,
tests/qemuxml2argvdata/qemuxml2argv-graphics-sdl.args,
tests/qemuxml2argvdata/qemuxml2argv-graphics-sdl.xml,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc-sasl.args,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc-sasl.xml,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc-tls.xml,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.xml,
tests/qemuxml2argvdata/qemuxml2argv-input-xen.xml: Add <video>
element for testing graphics adapter
* tests/qemuxml2argvtest.c: Add QEMUD_CMD_FLAG_VGA flag
* tests/qemuxml2xmltest.c: Add missing graphics-vnc-sasl/tls tests
* src/node_device_hal.c src/node_device_conf.[ch]: add support
for serial number in HAL storage backend, patch by Dave Allan
* docs/schemas/nodedev.rng
tests/nodedevschemadata/storage_serial_3600c0ff000d7a2a5d463ff4902000000.xml:
update the schemas and add a test case, also by Dave Allan
Daniel
* src/Makefile.am src/node_device.[ch] src/node_device_conf.[ch]
src/node_device_hal.[ch] src/node_device_hal_linux.c
src/qemu_driver.c src/remote_internal.c src/storage_backend.c
src/virsh.c src/xen_unified.c tests/nodedevxml2xmltest.c
po/POTFILES.in: implementation for node device create and destroy
in NPIV support, patch by David Allan
Daniel
* src/qemu_conf.c docs/schemas/domain.rng
tests/capabilityschemadata/caps-qemu-kvm.xml: PPC Qemu Machine Type
changed from g3bw to g3beige some time ago, patch by Thomas Baker
Daniel
* docs/schemas/storagevol.rng docs/formatstorage.html[.in]
tests/storagevolschemadata/vol-qcow2.xml: fix storage volume
inconsistencies in schema and document, patch by Ryota Ozaki
daniel
virExec will write out the pid of the daemonized process only. Use this
in the QEMU driver, rather than QEMU's pidfile, so we can catch errors we
might miss if the emulator bails early.
Seems like a simple typo - it has been "format=" since the flag
was introduced, but we added it as "fmt=".
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
* tests/libvirtd-pool: New file.
Exercise the new unix_sock_dir option
* tests/libvirtd-fail: New file.
* tests/Makefile.am (test_scripts): Add libvirtd-fail and libvirtd-pool.
* docs/schemas/domain.rng src/domain_conf.c src/domain_conf.h
src/qemu_conf.c
tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address.xml
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address.xml
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.xml:
adds a new <hostdev managed='(yes|no)'> property
to host devices indicating whether or not we should
automatically dettach/reset, patch by Mark McLoughlin
daniel
Add a test to check node device XML parsing by first parsing
the XML, then re-formatting as XML and finally comparing the
resulting XML to the original XML.
* docs/formatdomain.html.in docs/libvirt.rng docs/formatdomain.html:
document the new PCI passthrough format
* tests/qemuxml2argvtest.c tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address.args
tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address.xml:
and add a regression test for it.
Daniel
* qemud/qemud.c qemud/test_libvirtd_qemu.aug tests/Makefile.am
tests/daemon-conf: fix make check with the new logging support
the messages now carry a timestamp which need to be removed,
the daemon needs to exit if the log configuration informations
are wrong and we also look at the LIBVIRT_DEBUG environment
variable
Daniel
* src/domain_conf.c src/domain_conf.h src/qemu_conf.c
tests/qemuxml2argvtest.c tests/qemuxml2xmltest.c
tests/qemuxml2argvdata/qemuxml2argv-graphics-sdl-fullscreen.args
tests/qemuxml2argvdata/qemuxml2argv-graphics-sdl-fullscreen.xml:
slightly modified patch for SDL fullscreen from Itamar Heim
* docs/formatdomain.html docs/formatdomain.html.in docs/libvirt.rng:
update the schemas and docs about the sdl graphic element attributes
* AUTHORS: add Itamar Heim
Daniel
* src/virsh.c (cmdPoolStart, cmdStart): Change hard-coded
vshCommandOptDomainBy string argument to match just-changed
option name. Cole Robinson reported that "virsh start" was
broken and provided that part of the fix.
Bug introduced by yesterday's "virsh.c: tweak options to produce
more accurate help".
* tests/start: New file. Test for the above fix.
* tests/Makefile.am (test_scripts): Add start.
This test would hang when failing to perturb the soon-to-be-
added numeric (and non-boolean) valued parameters, max_clients,
max_workers, min_workers.
* tests/daemon-conf: Require that all commented-out settings
in libvirtd.conf have the same form. Before, two parameters
were not being tested, since a space had snuck between the
leading "#" and the "param = value" parts.
Apply each RHS-value-perturbing transformation
separately, not in series.
Let VERBOSE=yes turn on debugging.
Be more verbose by default, since this is a relatively
long-running test.
* qemud/libvirtd.conf: Normalize the spacing around each setting
that is to be perturbed by tests/daemon-conf.
* tests/virsh-synopsis: new file
* tests/Makefile.am (test_scripts): Add virsh-synopsis.
* src/virsh.c: Correct help SYNOPSIS for each of seven commands.
When I first ran this script, "make check" failed like this:
...
invalid help SYNOPSIS for net-create:
create a network from an XML <file>
invalid help SYNOPSIS for net-define:
define a network from an XML <file>
invalid help SYNOPSIS for net-start:
start <network>
invalid help SYNOPSIS for pool-create:
create a pool from an XML <file>
invalid help SYNOPSIS for pool-define:
define a pool from an XML <file>
invalid help SYNOPSIS for pool-start:
start <pool>
invalid help SYNOPSIS for vol-create:
create <file>
FAIL: virsh-synopsis
* tests/virshtest.c: Embed literal, expected output here, rather than
using virshdata/*.txt file names.
Factor out some common constructs.
(testCompareOutputLit): New function.
(testCompareOutput): #ifdef-out, not that it's unused.
* tests/Makefile.am (SUBDIRS): Remove virshdata/ and all files in it.
* docs/testnode.xml: Fix typo in a comment.
* configure.in (AC_OUTPUT): Remove tests/virshdata/Makefile.
* Makefile.maint (sync-vcs-ignore-files): New target.
Prompted by a patch from James Morris.
http://thread.gmane.org/gmane.comp.emulators.libvirt/8619/focus=8773
Add all (now-generated) .gitignore files.
* .gitignore: New file.
* build-aux/.gitignore: New file.
* docs/.gitignore: New file.
* docs/devhelp/.gitignore: New file.
* docs/examples/.gitignore: New file.
* docs/examples/python/.gitignore: New file.
* gnulib/lib/.gitignore: New file.
* gnulib/lib/arpa/.gitignore: New file.
* gnulib/lib/netinet/.gitignore: New file.
* gnulib/lib/sys/.gitignore: New file.
* gnulib/tests/.gitignore: New file.
* include/.gitignore: New file.
* include/libvirt/.gitignore: New file.
* po/.gitignore: New file.
* proxy/.gitignore: New file.
* python/.gitignore: New file.
* python/tests/.gitignore: New file.
* qemud/.gitignore: New file.
* src/.gitignore: New file.
* tests/.gitignore: New file.
* tests/confdata/.gitignore: New file.
* tests/sexpr2xmldata/.gitignore: New file.
* tests/virshdata/.gitignore: New file.
* tests/xencapsdata/.gitignore: New file.
* tests/xmconfigdata/.gitignore: New file.
* tests/xml2sexprdata/.gitignore: New file.
* src/qemu_conf.c: fix serial/telnet to use "server" option
rather than "listen"
* tests/qemuxml2argvdata/qemuxml2argv-serial-tcp-telnet.args:
fix the test case too
* tests/qemuxml2argvtest.c (testCompareXMLToArgvFiles): Adjust the
code that creates "actual" output, so that it too produces a
newline-terminated buffer.
* tests/qemuxml2argvdata/*.args: Append a newline to each, via:
for i in $(find|grep '\.args$'); do echo >> $i;done
* src/domain_conf.c src/domain_conf.h src/qemu_conf.c
src/qemu_driver.c: patch from Guido Günther allowing to add
disk as USB devices
* docs/libvirt.rng: extend the schemas for the new value
* tests/qemuxml2argvdata/qemuxml2argv-disk-usb.args
tests/qemuxml2argvdata/qemuxml2argv-disk-usb.xml
tests/qemuxml2argvtest.c tests/qemuxml2xmltest.c: add a specific
test to the regression suite
Daniel
* src/domain_conf.c src/domain_conf.h src/qemu_conf.c
src/qemu_driver.c: Patch from Guido Günther allowing to pass
usb devices to qemu/kvm
* docs/libvirt.rng: add the new functionality to the grammar
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address.args
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address.xml
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.args
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.xml
tests/qemuxml2argvtest.c tests/qemuxml2xmltest.c: adding examples
to the regression tests
* libvirt.spec.in: fix the licence tag
Daniel
part, this doesn't really concern libvirt, since for things like attach and
detach we just pass it through and let xend worry about whether it is supported
or not. The one place this breaks down is in the stats collecting code, where
we need to figure out the device number so we can go digging in /sys for the
statistics.
To remedy this, I've re-written xenLinuxDomainDeviceID() to use regular
expressions to figure out the device number from the name. The major advantage
is that now xenLinuxDomainDeviceID() looks fairly identical to
tools/python/xen/util/blkif.py (in the Xen sources), so that adding additional
devices in the future should be much easier. It also reduces the size of the
code, and, in my opinion, the code complexity.
With this patch in place, I was able to get block statistics both on older style
devices (/dev/xvda) and on the new, expanded devices (/dev/xvdaa).
Signed-off-by: Chris Lalancette <clalance@redhat.com>
handling code. In particular, if you had a section of XML like:
<disk type='file' device='cdrom'>
<target dev='hdc' bus='ide'/>
<readonly/>
</disk>
This used to work with older libvirt, but now fails. This is because we are
actually passing the literal string (null) to the qemu command-line, which qemu
barfs on. This patch fixes it up by making it blank, which allows qemu to
continue on it's merry way.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
* src/virsh.c (cmdUndefine): Tell user to shutdown and then use name or UUID.
* tests/undefine: New test. Exercise virsh's undefine command.
* tests/Makefile.am (test_scripts): Add undefine.
release
* src/xm_internal.c: fix xm driver serialization escapes
* tests/xmconfigtest.c tests/xmconfigdata/test-escape-paths.cfg
tests/xmconfigdata/test-escape-paths.xml: add test for previous
problem
Daniel
* src/util.c (fread_file_lim): Use VIR_REALLOC_N, not VIR_ALLOC_N.
Bug introduced in 895d0fdf5b.
* tests/Makefile.am (test_scripts): Add read-bufsiz.
* tests/read-bufsiz: New test for the above.
* configure.in: Document AC_SYS_LARGEFILE.
* docs/hvsupport.html.in: Document HV support for virDomainBlockPeek.
* include/libvirt/libvirt.h.in, src/driver.h, src/libvirt.c,
src/libvirt_sym.version: Add virDomainBlockPeek infrastructure.
* src/qemu_driver.c, src/test.c: Null versions of this call.
* src/xen_unified.c, src/xend_internal.c, src/xend_internal.h,
src/xm_internal.c, src/xm_internal.h: Xen implementation.
* tests/sexpr2xmldata/sexpr2xml-curmem.xml,
tests/sexpr2xmldata/sexpr2xml-no-source-cdrom.xml: XML output
has been reordered slightly in the Xen driver, but should be
functionally the same.
Done using this command (also includes .c.in and .h.in files):
for i in $(g ls-files|grep -E '\.[ch](\.in)?$'|grep -v gnulib); do
expand -i $i > j && mv j $i;done
* src/util.c (fread_file_lim): New function.
(__virFileReadAll): Use fread_file_lim, rather than requiring
that stat.st_size provide a usable file size.
* tests/read-non-seekable: New test, for the above.
* tests/Makefile.am (test_scripts): Add read-non-seekable.
* tests/test-lib.sh (mkfifo_or_skip_): New helper function.
* tests/Makefile.am (test_scripts): Add vcpupin.
(EXTRA_DIST): Add test-lib.sh.
* tests/test-lib.sh: Testing framework, from coreutils.
* tests/vcpupin: New file.
* build-aux/mktempd: New file, from gnulib.
* bootstrap: Add posix-shell and mktempd to the list of imported modules.
* gnulib/m4/posix-shell.m4: New file, from gnulib.
* tests/Makefile.am (TESTS_ENVIRONMENT): Correct invalid
settings of abs_top_builddir and abs_top_srcdir.
Also prepend src/ to PATH, so we test the just-built virsh,
not whatever happens to be in the original $PATH.
src/libvirt.c src/qemu.conf src/remote_internal.c src/xend_internal.c
tests/confdata/libvirtd.conf tests/confdata/libvirtd.out: patch from
Atsushi SAKAI fixing a ot more typo
Daniel
* src/Makefile.am: Create a convenience library, libvirt_test.la,
and don't restrict access to *its* symbols.
* tests/Makefile.am (LDADDS): Add ../src/libvirt_test.la, so that
"configure --disable-shared" no longer provokes link errors.
(LIBVIRT): Remove definition.
(LDADDS): Remove use.
($(LIBVIRT)): Remove rule.
(LDADDS): Use the new convenience library instead.
(CLEANFILES): Define.
* docs/examples/index.py (dump_Makefile): Append $(COVERAGE_LDFLAGS),
to the LDADDS definition, to avoid link error with the combination of
--enable-test-coverage and --disable-shared.
* docs/examples/Makefile.am: Regenerate.
* docs/examples/index.html: Likewise.
* qemud/Makefile.am (libvirtd_LDFLAGS): Append $(COVERAGE_LDFLAGS).
* src/libvirt_sym.version: Remove some SP-before-TAB.
Use <config.h>, not "config.h", per autoconf documentation.
* Makefile.cfg (local-checks-to-skip) [sc_require_config_h]: Enable.
* .x-sc_require_config_h: New file, to list exempted files.
* Makefile.am (EXTRA_DIST): Add .x-sc_require_config_h.
* docs/examples/suspend.c: Declare global "conn" to be static.
* tests/qemuxml2argvtest.c: Declare global "driver" to be static.
* tests/qemuxml2xmltest.c: Likewise.
Author: Jim Meyering <meyering@redhat.com>
* tests/Makefile.am (TESTS_ENVIRONMENT): Adjust PATH setting
to work also with automake-1.9. Can't use $(abs_top_builddir).
Author: Jim Meyering <meyering@redhat.com>
Given code like: T *var = calloc (n, sizeof (T));
Convert to this: T *var = calloc (n, sizeof (*var));
This first-cut change adjusts all malloc, calloc, and
realloc statements.
The only binary differences are in remote_internal.c
(due to the bug fix) and in xmlrpc.c (due to factorization).
* python/libvir.c: As above.
* qemud/event.c: Likewise.
* qemud/mdns.c: Likewise.
* qemud/qemud.c: Likewise.
* qemud/remote.c: Likewise.
* src/bridge.c: Likewise.
* src/buf.c: Likewise.
* src/conf.c: Likewise.
* src/hash.c: Likewise.
* src/iptables.c: Likewise.
* src/openvz_conf.c: Likewise.
* src/qemu_conf.c: Likewise.
* src/qemu_driver.c: Likewise.
* src/test.c: Likewise.
* src/xen_internal.c: Likewise.
* src/xen_unified.c: Likewise.
* src/xm_internal.c: Likewise.
* src/xml.c: Likewise.
* tests/qemuxml2argvtest.c: Likewise.
* src/xmlrpc.c (xmlRpcValuePtr): Likewise, and minor factorization.
* src/remote_internal.c (remoteAuthMakeCredentials): Use the right
type when allocating space for an array of cred _pointers_.
And remove a minor diagnostic inconsistency.
* tests/daemon-conf: New test.
* tests/Makefile.am (TESTS_ENVIRONMENT): Prepend qemud/ to PATH,
so we can invoke libvirtd without an absolute name.
(test_scripts): Add daemon-conf.
* qemud/qemud.c (remoteConfigGetAuth): Use checkType,
rather than open-coding it with a different diagnostic.
New files go into these directories:
gnulib/lib
gnulib/m4
gnulib/tests
* bootstrap: A wrapper around gnulib-tool.
* configure.in: Invoke gl_EARLY and gl_INIT, being careful to put gl_EARLY
before any macro that uses AC_COMPILE_IFELSE.
(AC_OUTPUT): Add lib/Makefile and gl-tests/Makefile. Remove m4/Makefile.
* Makefile.am (SUBDIRS): Add gnulib/lib and remove m4. Add gnulib/tests
early enough that those tests run before any libvirt unit tests.
* m4/Makefile.am: Remove file. Not needed.
* src/Makefile.am (INCLUDES): Add -I$(top_srcdir)/gnulib/lib -I../gnulib/lib.
(LDADDS, libvirt_la_LIBADD): Add ../gnulib/lib/libgnu.la.
* src/nodeinfo.c: Include "physmem.h".
* qemud/qemud.c, src/remote_internal.c: Include "getaddrinfo.h".
(MEMINFO_PATH, linuxNodeInfoMemPopulate): Remove definitions.
(virNodeInfoPopulate): Use physmem_total, not linuxNodeInfoMemPopulate.
* tests/Makefile.am (INCLUDES): Add -I$(top_srcdir)/gnulib/lib -I../gnulib/lib.
(LDADDS): Add ../gnulib/lib/libgnu.la.
* qemud/Makefile.am (libvirtd_LDADD): Add ../gnulib/lib/libgnu.la.
* tests/nodeinfotest.c (linuxTestCompareFiles): No longer read total
memory from a file.
Update expected output not to include "Memory: NNNN"
* tests/nodeinfodata/linux-nodeinfo-1.txt:
* tests/nodeinfodata/linux-nodeinfo-2.txt:
* tests/nodeinfodata/linux-nodeinfo-3.txt:
* tests/nodeinfodata/linux-nodeinfo-4.txt:
* tests/nodeinfodata/linux-nodeinfo-5.txt:
* tests/nodeinfodata/linux-nodeinfo-6.txt:
* src/test.c [WITH_TEST]: Remove definition of _GNU_SOURCE that
would conflict with the one now in "config.h".
* autogen.sh: Add -I gnulib/m4.
* src/conf.c, src/sexpr.c: Don't define _GNU_SOURCE.
Instead, include "config.h".
* qemud/qemud.c: Remove definition of _GNU_SOURCE.
* src/openvz_driver.c: Likewise.
* src/qemu_driver.c: Likewise.
* src/remote_internal.c: Likewise.
* configure.in: Use AC_CONFIG_AUX_DIR(build-aux), so that a bunch
of gettextize-generated files go into build-aux/, rather than in
the top-level directory.
* .cvsignore: Adjust.
* build-aux/.cvsignore: New file.
Author: Jim Meyering <meyering@redhat.com>
* python/libvir.c, python/libvirt_wrap.h, qemud/qemud.c,
qemud/remote.c, src/internal.h, src/openvz_conf.c,
src/openvz_driver.c, src/proxy_internal.h, src/qemu_conf.c,
src/qemu_driver.c, src/remote_internal.h, src/test.h, src/util.c,
src/xen_unified.c, src/xen_unified.h, tests/nodeinfotest.c,
tests/qemuxml2argvtest.c, tests/qemuxml2xmltest.c, tests/reconnect.c,
tests/sexpr2xmltest.c, tests/virshtest.c, tests/xencapstest.c,
tests/xmconfigtest.c, tests/xml2sexprtest.c:
Change #include <> to #include "" for local includes.
Removed many includes from src/internal.h and put them in
the C files which actually use them.
Removed <ansidecl.h> - unused.
Added a comment around __func__.
Removed a clashing redefinition of VERSION symbol.
All limits (PATH_MAX etc) now done in src/internal.h, so we
don't need to include those headers in other files.
* tests/Makefile.am, tests/nodeinfotest.c, tests/qemuxml2argvtest.c,
tests/qemuxml2xmltest.c, tests/sexpr2xmltest.c, tests/virshtest.c,
tests/xencapstest.c, tests/xmconfigtest.c, tests/xml2sexprtest.c:
Miscellaneous fixes to the tests to compile under Cygwin.
if the path environment variable is missing, add the tests for
<shareable/> from/to w! ode for disk
* tests/sexpr2xmldata/sexpr2xml-disk-block-shareable.sexpr
tests/sexpr2xmldata/sexpr2xml-disk-block-shareable.xml
tests/xml2sexprdata/xml2sexpr-disk-block-shareable.sexpr
tests/xml2sexprdata/xml2sexpr-disk-block-shareable.xml:
the new tests data
Daniel
* Makefile.am: Expand some "*" wildcards, and (for now) disable
the relatively unimportant, distuninstallcheck target.
Fix a few redirect-directly-to-target bugs.
Add a few $(srcdir)/ prefixes and add an uninstall-local rule.
* docs/Makefile.am: More of the same. Split some long lines.
* python/Makefile.am: Likewise.
* python/tests/Makefile.am: Likewise.
* qemud/Makefile.am: Likewise.
* tests/Makefile.am: Remove the directories already listed in SUBDIRS.
* docs/examples/index.py: Adapt to produce the desired changes in
docs/examples/Makefile.am. Also, sort *.c, so results are reproducible,
and emit a comment telling emacs and vi that the file is read-only.
* docs/examples/Makefile.am: Regenerate.
Author: Jim Meyering <meyering@redhat.com>
* tests/Makefile.am: Include the contents of the *data directories
in the make-dist-built tarball by adding each of that *data
directories to EXTRA_DIST.
Also add int-overflow (via $(test_scripts)) to EXTRA_DIST.
* tests/nodeinfotest.c: Prepend "$abs_top_srcdir/tests" to
each input file name.
* tests/qemuxml2argvtest.c: Likewise.
* tests/qemuxml2xmltest.c: Likewise.
* tests/sexpr2xmltest.c: Likewise.
* tests/test_conf.sh: Likewise.
* tests/virshtest.c: Likewise.
* tests/xencapstest.c: Likewise.
* tests/xmconfigtest.c: Likewise.
* tests/xml2sexprtest.c: Likewise.
Author: Jim Meyering <meyering@redhat.com>
Patch from Jim Meyering
* src/internal.h: Include <errno.h>.
Define new static inline function, xstrtol_i.
* src/virsh.c: Detect integer overflow in domain ID number
in vshCommandOptDomainBy. Detect overflow and invalid port
number suffix in cmdVNCDisplay.
* src/xend_internal.c: Parse CPU number more carefully in
xenDaemonDomainGetVcpus.
* tests/int-overflow: New script. Test for the above-fixed bug.
* tests/Makefile.am: Add int-overflow to TESTS. Define
TESTS_ENVIRONMENT, to propagate $abs_top_* variables into the
int-overflow script. Adapt the "valgrind" rule not to clobber
new TESTS_ENVIRONMENT.
Daniel
* tests/conftest.c: Use fwrite, not printf, since the
result buffer is not NUL-terminatedi, from Jim Meyering.
* tests/qemuxml2argvtest.c: Initialize vm.migrateFrom[0],
to avoid "read-uninitialized" error from within
qemudBuildCommandLinei, from Jim Meyering.
Daniel
src/driver.h src/libvirt.c src/openvz_driver.c src/qemu_driver.c
src/test.c src/xen_unified.c src/xend_internal.c: add new API
virNodeGetFreeMemory(), extends the driver. Lacks remote and
QEmu support though.
* src/libvirt.c: allows to fix virNodeGetCellsFreeMemory() adding
parameter check for startCell.
* proxy/libvirt_proxy.c src/xend_internal.[ch]
include/libvirt/libvirt.h include/libvirt/libvirt.h.in: applied
vncpasswd dump patch from Mark Johnson but with the
virDomainXMLFlags extension as suggested by Daniel Berrange
this changed a couple of internal APIs too
* tests/sexpr2xmldata/sexpr2xml-no-source-cdrom.xml: fix one of the
tests affected by bootloader dump change.
Daniel
patch from David Lutterkort
* tests/xencapsdata/xen-i686-pae-hvm.xml
tests/xencapsdata/xen-ia64-be-hvm.xml
tests/xencapsdata/xen-ia64-hvm.xml
tests/xencapsdata/xen-x86_64-hvm.xml: this also affects a few tests
Daniel
* src/conf.c, src/test.c, src/xen_internal.c: Readd checking
of errors from virBuffer functions.
* src/sexpr.c: Add comment about use of _GNU_SOURCE.
* src/virsh.c: Remove use of _GNU_SOURCE / isblank.
* src/xml.c, tests/Makefile.am: Minor cleanup.
for arguments to bootloader, patch from Hugh Brock
* tests/sexpr2xmltest.c tests/xml2sexprtest.c
tests/sexpr2xmldata/sexpr2xml-pv-bootloader.sexpr
tests/sexpr2xmldata/sexpr2xml-pv-bootloader.xml
tests/xml2sexprdata/xml2sexpr-pv-bootloader.sexpr
tests/xml2sexprdata/xml2sexpr-pv-bootloader.xml: add specific
regression tests
Daniel
+
+ * TODO: Added a note about requiring C++ compiler because of a
+ possible problem with libtool autoconf macros.
+ * docs/examples/Makefile.am, proxy/Makefile.am, qemud/Makefile.am,
+ src/Makefile.am, tests/Makefile.am: Pass $(WARN_CFLAGS) when
+ linking, so if -fstack-protector is there, gcc will link to
+ the stack protector library.
+ * tests/xencapstest.c: Allow this test to compile when Xen
+ libraries are not enabled.
+
* src/test.c, src/libvirt.c, src/virterror.c,
include/libvirt/virterror.h: Add a VIR_FROM_TEST error class
and ensure that test driver errors are from this class.
Tidy up the error messages generated by the test driver when
user doesn't add a path to the URL and avoid open ("/").
to handle CDRom devices with no device name
* tests/sexpr2xmltest.c tests/xml2sexprtest.c
tests/sexpr2xmldata/sexpr2xml-no-source-cdrom.sexpr
tests/sexpr2xmldata/sexpr2xml-no-source-cdrom.xml
tests/xml2sexprdata/xml2sexpr-no-source-cdrom.sexpr
tests/xml2sexprdata/xml2sexpr-no-source-cdrom.xml: added regression
tests for this case based on Nobuhiro Itou test inputs.
Daniel
src/Makefile.am src/libvirt.c src/qemu_internal.c src/test.c
src/xen_internal.c src/xen_internal.h src/xend_internal.c
src/xm_internal.c src/xml.c src/xs_internal.c
tests/Makefile.am tests/sexpr2xmltest.c tests/xmconfigtest.c:
allow selective compilation of Xen,QEmu/KVM and test support
in or out at configure time. Also allows to compile on a system
without Xen development installed. All drivers are selected by
default.
Daniel
* acinclude.m4: add LIBVIRT_COMPILE_WARNINGS, copied from
GNOME but with a few more flags we'd been using.
* configure.in: use that instead of setting CFLAGS
directly.
* proxy/Makefile.am, python/Makefile.am, qemud/Makefile.am,
src/Makefile.am, tests/Makefile.am: use $(WARN_CFLAGS)
* src/xend_internal.c, src/xm_internal.c: pass the
connection to virDomainParseXMLDesc()
* src/xml.[ch]: make virDomainParseXMLDesc accept
a virConnectPtr so that we can use it later to
lookup the bridge associated with a network
* tests/xml2sexprtest.c: just pass NULL here, it's
safe
to the XML description and handle its serialization back and
forth between XML and S-Expr
* tests/sexpr2xmltest.c tests/xml2sexprtest.c
tests/sexpr2xmldata/sexpr2xml-curmem.*
tests/xml2sexprdata/xml2sexpr-curmem.*: added specific regression
tests for this, this didn't disturb any of the other tests.
Daniel
* src/xend_internal.c: fix the reconnection problem to xend pointed
by Philippe Berthault
* tests/Makefile.am tests/reconnect.c: add a specific test case
Daniel
* configure.in include/libvirt/virterror.h src/Makefile.am
src/conf.c src/conf.h src/virterror.c src/xen_internal.c:
adding a subset of Xen config file parser, and serializer
* tests/Makefile.am tests/conftest.c tests/test_conf.sh
tests/confdata/Makefile.am tests/confdata/fc4.conf
tests/confdata/fc4.out: adding test program for config in and out
Daniel
include/libvirt/virterror.h python/generator.py python/libvir.c
python/libvirt_wrap.h src/driver.h src/internal.h src/test.h
src/virsh.c src/virterror.c src/xend_internal.c src/xend_internal.h
src/xml.c src/xml.h: moved the includes from include/ to
include/libvirt to reflect the installed include tree. This
avoid using "" in the includes themselves.
Daniel
