A future patch will refactor the storage of the pinning information in a
way where the ordering will be lost. Order them numerically to avoid
changing the tests later.
Autodeflate can be enabled/disabled for memballon device
of model 'virtio'.
xml:
<devices>
<memballoon model='virtio' autodeflate='on'/>
</devices>
qemu:
qemu -device virtio-balloon-pci,...,deflate-on-oom=on
Autodeflate cannot be enabled/disabled for running domain.
Use virDomainDefAddUSBController() to add an EHCI1+UHCI1+UHCI2+UHCI3
controller set to newly defined Q35 domains that don't have any USB
controllers defined.
The real Q35 machine puts the first USB controller set (EHCI+(UHCIx4))
on bus 0 slot 0x1D, and the 2nd USB controller set on bus 0 slot 0x1A,
so let's attempt to make the virtual machine match that for
controllers with auto-assigned addresses when possible.
Three test cases were added to assure that the proper addresses are
assigned - one with a single set of unaddressed USB controllers, one
with 3 (to grab both preferred slots plus one more), and one with the
order of the controller definitions reordered, to assure that the
auto-assignment isn't mixed up by order.
If the q35 specific disable s3/s4 setting isn't supported, fallback to
specifying the PIIX setting, which is the previous behavior. It doesn't
have any effect, but qemu will just warn about it rather than error:
qemu-system-x86_64: Warning: global PIIX4_PM.disable_s3=1 not used
qemu-system-x86_64: Warning: global PIIX4_PM.disable_s4=1 not used
Since it doesn't error, I don't think we should either, since there
may be configs in the wild that already have q35 + disable_s3/4 (via
virt-manager)
The condition was checking for UHCI (and OHCI for ppc64) availability so
that it can specify the proper device instead of legacy usb. However,
for ppc64, we don't need to check both OHCI and UHCI, but only OHCI as
that is the legacy default. The condition is so big that it was just a
matter of time when someone will make a mistake there, so let's use more
lines so that it is visible what the condition checks for.
This fixes usage of -device instead of -usb for ppc64 that supports
pci-usb-ohci and does not support piix3-usb-uhci.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1297020
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If user defines a virtio channel with UNIX socket backend and doesn't
care about the path for the socket (e.g. qemu-agent channel), we still
generate it into the persistent XML. Moreover when then user renames
the domain, due to its persistent socket path saved into the per-domain
directory, it will not start. So let's forget about old generated paths
and also stop putting them into the persistent definition.
https://bugzilla.redhat.com/show_bug.cgi?id=1278068
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
By default, QEMU truncates serial file on open. Sometimes, it could be weird -
for example, when we are trying to investigate some event, which occured several
restarts ago. This patch adds an ability to preserve previous content.
Signed-off-by: Dmitry Mishin <dim@virtuozzo.com>
Since libvirt for dubious historical reasons stores memory size as
kibibytes, it's possible that the alignments done in the qemu code
overflow the the maximum representable size in bytes. The XML parser
code handles them in bytes in some stages. Prevent this by doing
overflow checks when alinging the size and add a test case.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1260576
To be used by the family of virtio input devices:
<input type='mouse' bus='virtio'/>
<input type='tablet' bus='virtio'/>
<input type='keyboard' bus='virtio'/>
https://bugzilla.redhat.com/show_bug.cgi?id=1231114
Check if virtio-gpu provides virgl option, and add qemu command line
formatter.
It is enabled with the existing accel3d attribute:
<model type='virtio' heads='1'>
<acceleration accel3d='yes'/>
</model>
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
qemu 2.5 provides virtio video device. It can be used with -device
virtio-vga for primary devices, or -device virtio-gpu for non-vga
devices. However, only the primary device (VGA) is supported with this
patch.
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=1195176
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
'model' attribute was added to a panic device but only one panic
device is allowed. This patch changes panic device presence
from 'optional' to 'zeroOrMore'.
Panic device type used depends on 'model' attribute.
If no model is specified then device type depends on hypervisor
and guest arch. 'pseries' model is used for pSeries guest and
'isa' model is used in other cases.
XML:
<devices>
<panic model='hyperv'/>
</devices>
QEMU command line:
qemu -cpu <cpu_model>,hv_crash
It's just a copy&paste of qemuxml2argv test anyway. We can test most of
them (except for qemuxmlns-qemu-ns-domain.xml which fails to validate
against our schema) by qemuxml2argv test.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
USB controllers can share the same 'index' which indicates, that there
is some sort of master-companion relationship. Reorder the controllers
in XML in to place the master controller before its companions. This is
required by QEMU to not fail with error message:
error: internal error: process exited while connecting to monitor:
2015-10-26T16:25:17.630265Z qemu-system-x86_64:
-device ich9-usb-uhci1,masterbus=usb.0,firstport=0,bus=pci.0,multifunction=on,addr=0x6:
USB bus 'usb.0' not found
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1166452
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The -sdl and -net ...name=XXX arguments were both introduced
in QEMU 0.10, so the QEMU driver can assume they are always
available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.10.0 the -vga argument was introduced, so the
QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.10.0, the -drive cache option stopped using
the on/off value names, so the QEMU driver can assume
use of the new value names.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Since we require QEMU 0.12.0, we can assume that QEMU supports
all of the fd, tcp, unix and exec migration protocols.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
We have twice previously attempted to remove Xenner
support
commit de9be0ab4d
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Wed Aug 22 17:29:01 2012 +0100
Remove xenner support
commit 92572c3d71
Author: Ján Tomko <jtomko@redhat.com>
Date: Wed Feb 18 16:33:50 2015 +0100
Remove code handling the QEMU_CAPS_DOMID capability
This change really does remove the last traces of it
in the capabilities handling code
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.1 the -drive argument can be used to configure
all disks, so the QEMU driver can assume it is always available
and drop support for -hda/-cdrom/etc.
Many of the tests need updating because a great many were
running without CAPS_DRIVE set, so using the -hda legacy
syntax.
Fixing the tests uncovered a bug in the argv -> xml
convertor which failed to handle disk with if=floppy.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1249981
When qemuDomainPinIOThread was added in commit id 'fb562614', a check
for the IOThread capability was not needed since a check for iothreadpids
covered the condition where the support for IOThreads was not present.
The iothreadpids array was only created if qemuProcessDetectIOThreadPIDs
was able to query the monitor for IOThreads. It would only do that if
the QEMU_CAPS_OBJECT_IOTHREAD capability was set.
However, when iothreadids were added in commit id '8d4614a5' and the
check for iothreadpids was replaced by a search through the iothreadids[]
array for the matching iothread_id that left open the possibility that
an iothreadids[] array was defined, but the entries essentially pointed
to elements with only the 'iothread_id' defined leaving the 'thread_id'
value of 0 and eventually the cpumap entry of NULL.
This was because, the original IOThreads commit id '72edaae7' only
checked if IOThreads were defined and if the emulator had the IOThreads
capability, then IOThread objects were added at startup. The "capability
failure" check was only done when a disk was assigned to an IOThread in
qemuCheckIOThreads. This was because the initial implementation had no way
to dynamically add IOThreads, but it was possible to dynamically add a
disk to the domain. So the decision was if the domain supported it, then
add the IOThread objects. Then if a disk with an IOThread defined was
added, it could check the capability and fail to add if not there. This
just meant the 'iothreads' value was essentially ignored.
Eventually commit id 'a27ed6e7' allowed for the dynamic addition and
deletion of IOThread objects. So it was no longer necessary to generate
IOThread objects to dynamically attach a disk to. However, the startup
and disk check code was not modified to reflect this.
This patch will move the capability failure check to when IOThread
objects are being added to the command line. Thus a domain that has
IOThreads defined will not be started if the emulator doesn't support
the capability. This means when qemuCheckIOThreads is called to add
a disk, it's no longer necessary to check the capability. Instead the
code can use the IOThreadFind call to indicate that the IOThread
doesn't exist.
Finally because it could be possible to have a domain running with the
iothreadids[] defined prior to this change if libvirtd is restarted each
having mostly empty elements, qemuProcessDetectIOThreadPIDs will check
if there are niothreadids when the QEMU_CAPS_OBJECT_IOTHREAD capability
check fails and remove the elements and array if it exists.
With these changes in place, it turns out the cputune-numatune test
was failing because the right bit wasn't set in the test. So used the
opportunity to fix that and create a test that would expect to fail
with some sort of iothreads defined and used, but not having the
correct capability.
- qemuxml2argv-aarch64-mmio-default-pci: Verify that we still default
to virtio-mmio even if qemu is new enough to support PCI
- qemuxml2argv-aarch64-virtio-pci: Check generated arm virtio PCI args
Our docs state that subelements of <metadata> shall have a namespace
and the medatata APIs expect that too. To avoid inaccessible
<metadata> sub-elements, just remove those that don't conform to the
documentation.
Apart from adding the new condition this patch renames the function and
refactors the code flow to allow the changes.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1245525
We are using memory-backing-file even when it's not needed, for example
if user requests hugepages for memory backing, but does not specify any
pagesize or memory node pinning. This causes migrations to fail when
migrating from older libvirt that did not do this. So similarly to
commit 7832fac847 which does it for
memory-backend-ram, this commit makes is more generic and
backend-agnostic, so the backend is not used if there is no specific
pagesize of hugepages requested, no nodeset the memory node should be
bound to, no memory access change required, and so on.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1266856
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
That function is called qemuBuildMemPathStr() and will be used in
other places in the future. The change in the test suite is proper due
to the fact that -mem-prealloc makes only sense with -mem-path (from
qemu documentation -- html/qemu-doc.html).
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
My original implementation was based on a qemu version that still did
not have all the checks in place. Using sizes that would align to odd
megabyte increments will produce the following error:
qemu-kvm: -device pc-dimm,node=0,memdev=memdimm0,id=dimm0: backend memory size must be multiple of 0x200000
qemu-kvm: -device pc-dimm,node=0,memdev=memdimm0,id=dimm0: Device 'pc-dimm' could not be initialized
Introduce an alignment retrieval function for memory devices and use it
to align the devices separately and modify a test case to verify it.
For some machine types ppc64 machines now require that memory sizes are
aligned to 256MiB increments (due to the dynamically reconfigurable
memory). As now we treat existing configs reasonably in regards to
migration, we can round all the sizes unconditionally. The only drawback
will be that the memory size of a VM can potentially increase by
(256MiB - 1byte) * number_of_NUMA_nodes.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1249006
When we are starting a qemu process for an incomming migration or
snapshot reloading we should not modify the memory sizes in the domain
since we could potentially change the guest ABI that was tediously
checked before. Additionally the function now updates the initial memory
size according to the NUMA node size, which should not happen if we are
restoring state.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1252685
https://bugzilla.redhat.com/show_bug.cgi?id=1260846
Introduced by 8fedbbdb, if we parse an unordered NUMA cell, will
get a segfault. This is because of a check for overlapping @cpus
sets we have there. However, since the array to hold guest NUMA
cells is allocated upfront and therefore it contains all zeros,
an out of order cell will break our assumption that cell IDs have
increasing character. At this point we try to access yet NULL
bitmap and therefore segfault.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Adds a new interface type using UDP sockets, this seems only applicable
to QEMU but have edited tree-wide to support the new interface type.
The interface type required the addition of a "localaddr" (local
address), this then maps into the following xml and qemu call.
<interface type='udp'>
<mac address='52:54:00:5c:67:56'/>
<source address='127.0.0.1' port='11112'>
<local address='127.0.0.1' port='22222'/>
</source>
<model type='virtio'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/>
</interface>
QEMU call:
-net socket,udp=127.0.0.1:11112,localaddr=127.0.0.1:22222
Notice the xml "local" entry becomes the "localaddr" for the qemu call.
reference:
http://lists.gnu.org/archive/html/qemu-devel/2011-11/msg00629.html
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
We are automatically generating some socket paths for domains, but all
those paths end up in a directory that's the same for multiple domains.
The problem is that multiple domains can each run with different
seclabels (users, selinux contexts, etc.). The idea here is to create a
per-domain directory labelled in a way that each domain can access its
own unix sockets.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1146886
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This controller can be connected only to a port on a
pcie-switch-upstream-port. It provides a single hotpluggable port that
will accept any PCI or PCIe device, as well as any device requiring a
pcie-*-port (the only current example of such a device is the
pcie-switch-upstream-port).
This controller can be connected only to a pcie-root-port or a
pcie-switch-downstream-port (which will be added in a later patch),
which is the reason for the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_PORT. A pcie-switch-upstream-port provides
32 ports (slot=0 to slot=31) on the downstream side, which can only
have pci controllers of model "pcie-switch-downstream-port" plugged
into them, which is the reason for the other new connect type
VIR_PCI_CONNECT_TYPE_PCIE_SWITCH.
This is backed by the qemu device ioh3420.
chassis and port from the <target> subelement are used to store/set the
respective qemu device options for the ioh3420. Currently, chassis is
set to be the index of the controller, and port is set to
"(slot << 3) + function" (per suggestion from Alex Williamson).
This controller can be connected (at domain startup time only - not
hotpluggable) only to a port on the pcie root complex ("pcie-root" in
libvirt config), hence the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_ROOT. It provides a hotpluggable port that
will accept any PCI or PCIe device.
New attributes must be added to the controller <target> subelement for
this - chassis and port are guest-visible option values that will be
set by libvirt with values derived from the controller's index and pci
address information.
This uses the new subelement/attribute in two ways:
1) If a "pci-bridge" pci controller has no chassisNr attribute, it
will automatically be set to the controller's index as soon as the
controller's PCI address is known (during
qemuDomainAssignPCIAddresses()).
2) when creating the commandline for a pci-bridge device, chassisNr
will be used to set qemu's chassis_nr option (rather than the previous
practice of hard-coding it to the controller's index).
There are some configuration options to some types of pci controllers
that are currently automatically derived from other parts of the
controller's configuration. For example, in qemu a pci-bridge
controller has an option that is called "chassis_nr"; up until now
libvirt has always set chassis_nr to the index of the pci-bridge. So
this:
<controller type='pci' model='pci-bridge' index='2'/>
will always result in:
-device pci-bridge,chassis_nr=2,...
on the qemu commandline. In the future we may decide there is a better
way to derive that option, but even in that case we will need for
existing domains to retain the same chassis_nr they were using in the
past - that is something that is visible to the guest so it is part of
the guest ABI and changing it would lead to problems for migrating
guests (or just guests with very picky OSes).
The <target> subelement has been added as a place to put the new
"chassisNr" attribute that will be filled in by libvirt when it
auto-generates the chassisNr; it will be saved in the config, then
reused any time the domain is started:
<controller type='pci' model='pci-bridge' index='2'>
<model type='pci-bridge'/>
<target chassisNr='2'/>
</controller>
The one oddity of all this is that if the controller configuration
is changed (for example to change the index or the pci address
where the controller is plugged in), the items in <target> will
*not* be re-generated, which might lead to conflict. I can't
really see any way around this, but fortunately if there is a
material conflict qemu will let us know and we will pass that on
to the user.
This new subelement is used in PCI controllers: the toplevel
*attribute* "model" of a controller denotes what kind of PCI
controller is being described, e.g. a "dmi-to-pci-bridge",
"pci-bridge", or "pci-root". But in the future there will be different
implementations of some of those types of PCI controllers, which
behave similarly from libvirt's point of view (and so should have the
same model), but use a different device in qemu (and present
themselves as a different piece of hardware in the guest). In an ideal
world we (i.e. "I") would have thought of that back when the pci
controllers were added, and used some sort of type/class/model
notation (where class was used in the way we are now using model, and
model was used for the actual manufacturer's model number of a
particular family of PCI controller), but that opportunity is long
past, so as an alternative, this patch allows selecting a particular
implementation of a pci controller with the "name" attribute of the
<model> subelement, e.g.:
<controller type='pci' model='dmi-to-pci-bridge' index='1'>
<model name='i82801b11-bridge'/>
</controller>
In this case, "dmi-to-pci-bridge" is the kind of controller (one that
has a single PCIe port upstream, and 32 standard PCI ports downstream,
which are not hotpluggable), and the qemu device to be used to
implement this kind of controller is named "i82801b11-bridge".
Implementing the above now will allow us in the future to add a new
kind of dmi-to-pci-bridge that doesn't use qemu's i82801b11-bridge
device, but instead uses something else (which doesn't yet exist, but
qemu people have been discussing it), all without breaking existing
configs.
(note that for the existing "pci-bridge" type of PCI controller, both
the model attribute and <model> name are 'pci-bridge'. This is just a
coincidence, since it turns out that in this case the device name in
qemu really is a generic 'pci-bridge' rather than being the name of
some real-world chip)
If a pci address had a function number out of range, the error message
would be:
Insufficient specification for PCI address
which is logged by virDevicePCIAddressParseXML() after
virDevicePCIAddressIsValid returns a failure.
This patch enhances virDevicePCIAddressIsValid() to optionally report
the error itself (since it is the place that decides which part of the
address is "invalid"), and uses that feature when calling from
virDevicePCIAddressParseXML(), so that the error will be more useful,
e.g.:
Invalid PCI address function=0x8, must be <= 7
Previously, virDevicePCIAddressIsValid didn't check for the
theoretical limits of domain or bus, only for slot or function. While
adding log messages, we also correct that ommission. (The RNG for PCI
addresses already enforces this limit, which by the way means that we
can't add any negative tests for this - as far as I know our
domainschematest has no provisions for passing XML that is supposed to
fail).
Note that virDevicePCIAddressIsValid() can only check against the
absolute maximum attribute values for *any* possible PCI controller,
not for the actual maximums of the specific controller that this
device is attaching to; fortunately there is later more specific
validation for guest-side PCI addresses when building the set of
assigned PCI addresses. For host-side PCI addresses (e.g. for
<hostdev> and for network device pools), we rely on the error that
will be logged when it is found that the device doesn't actually
exist.
This resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1004596
PowerPC pseries based VMs do not support a floppy disk controller.
This prohibits libvirt from creating qemu command with floppy device.
Signed-off-by: Kothapally Madhu Pavan <kmp@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1180486
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This reverts commit 7b401c3bda.
Until libvirt is able to differentiate whether heads='1' is just a
leftover from previous libvirt or whether that's added by user on
purpose and also whether the domain was started with the support for
qxl's max_outputs, we cannot incorporate this patch into the tree
due to compatibility reasons.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Allows to specify maximum number of head to QXL driver.
Actually can be a compatiblity problem as heads in the XML configuration
was set by default to '1'.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
This patch adds a test for the qemu command line generation.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1142631
Commit id 'e0e290552' added a check to determine if the same bus
had the same target value. It seems that's not quite good enough
as the check should check the target name value regardless of bus type.
Also added a DO_TEST_DIFFERENT to exhibit the issue
If user passes an invalid address for shared memory device to qemu,
neither libvirt nor qemu will report an error, but qemu will auto assign
a pci address to the shared memory device.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Since QEMU commit ea96bc6 [1]:
i386: drop FDC in pc-q35-2.4+ if neither it nor floppy drives are wanted
the floppy controller is no longer implicit.
Specify it explicitly on the command line if the machine type version
is 2.4 or later.
Note that libvirt's floppy drives do not result in QEMU implying the
controller, because libvirt uses if=none instead of if=floppy.
https://bugzilla.redhat.com/show_bug.cgi?id=1227880
[1] http://git.qemu.org/?p=qemu.git;a=commitdiff;h=ea96bc6
The code which generates paths for UNIX socket blindly used target name
without checking if it was set. Thus for the following device XML
<channel type='unix'>
<source mode='bind'/>
<target type='virtio'/>
</channel>
we would generate "/var/lib/libvirt/qemu/channel/target/NAME.(null)"
path which works but is not really correct. Let's not use the
".target_name" suffix at all if target name is not set.
https://bugzilla.redhat.com/show_bug.cgi?id=1226854
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Make sure we only assign the default spicevmc channel name to spicevmc
virtio channels. Caused by commits 3269ee65 and 1133ee2b, which moved
the assignment from XML parsing code to QEMU but failed to keep the
logic.
https://bugzilla.redhat.com/show_bug.cgi?id=1179680
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Proper Haswell CPU model handling is tested in several
qemuxml2argv-cpu-* which are run in a special environment. Let's remove
the CPU model from other tests to make them less fragile.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
So far the argument has not much meaning and was practically ignored.
This is not good since when doing memory hotplug, the size of desired
hugepage backing is passed in that argument. Taking closer look at the
tests I'm fixing reveals the bug. For instance, while the following is
in the test:
<memory model='dimm'>
<source>
<nodemask>1-3</nodemask>
<pagesize unit='KiB'>4096</pagesize>
</source>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
<address type='dimm' slot='0' base='0x100000000'/>
</memory>
the generated commandline corresponding to this XML was:
-object memory-backend-ram,id=memdimm0,size=536870912,\
host-nodes=1-3,policy=bind
Have you noticed? Yes, memory-backend-ram! Nothing can be further away
from the right answer. The hugepage backing is requested in the XML
and we happily ignore it. This is just not right. It's
memory-backend-file which should have been used:
-object memory-backend-file,id=memdimm0,prealloc=yes,\
mem-path=/dev/hugepages4M/libvirt/qemu,size=536870912,\
host-nodes=1-3,policy=bind
The problem is, that @pagesize passed to qemuBuildMemoryBackendStr
(where this part of commandline is built) was ignored. The hugepage to
back memory was searched only and only by NUMA nodes pinning. This
works only for regular guest NUMA nodes.
Then, I'm changing the hugepages size in the test XMLs too. This is
simply because in the test suite we create dummy mount points just for
2M and 1G hugepages. And in the test 4M was requested. I'm sticking to
2M, but 1G should just work too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1196644
This function constructs the backend (host facing) part of the
memory device. At the beginning, the configured hugepages are
searched to find the best match for given guest NUMA node.
Configured hugepages can have a @nodeset attribute to specify on
which guest NUMA nodes should be the hugepages backing used.
There is, however, one 'corner case'. Users may just tell 'use
hugepages to back all the nodes'. In other words:
<memoryBacking>
<hugepages/>
</memoryBacking>
<cpu>
<numa>
<cell id='0' cpus='0-1' memory='1024000' unit='KiB'/>
</numa>
</cpu>
Our code fails in this case. Well, since there's no @nodeset (nor
any <page/> child element to <hugepages/>) we fail to lookup the
default hugepage size to use.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1235116
According to our XML definition, zero is as valid as any other value.
Mainly because it should be kernel-agnostic.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Defining a domain with a SCSI disk attached via a hostdev
tag and a source address unit value longer than two digits
causes an error when editing the domain with virsh edit,
even if no changes are made to the domain definition.
The error suggests invalid XML, somewhere:
# virsh edit lmb_guest
error: XML document failed to validate against schema:
Unable to validate doc against /usr/local/share/libvirt/schemas/domain.rng
Extra element devices in interleave
Element domain failed to validate content
The virt-xml-validate tool fails with a similar error:
# virt-xml-validate lmb_guest.xml
Relax-NG validity error : Extra element devices in interleave
lmb_guest.xml:17: element devices: Relax-NG validity error :
Element domain failed to validate content
lmb_guest.xml fails to validate
The hostdev tag requires a source address to be specified,
which includes bus, target, and unit address attributes.
According to the SCSI Architecture Model spec (section
4.9 of SAM-2), a LUN address is 64 bits and thus could be
up to 20 decimal digits long. Unfortunately, the XML
schema limits this string to just two digits. Similarly,
the target field can be up to 32 bits in length, which
would be 10 decimal digits.
# lsscsi -xx
[0:0:19:0x4022401100000000] disk IBM 2107900 3.44 /dev/sda
# lsscsi
[0:0:19:1074872354]disk IBM 2107900 3.44 /dev/sda
# cat lmb_guest.xml
<domain type='kvm'>
<name>lmb_guest</name>
<memory unit='MiB'>1024</memory>
...trimmed...
<devices>
<controller type='scsi' model='virtio-scsi' index='0'/>
<hostdev mode='subsystem' type='scsi'>
<source>
<adapter name='scsi_host0'/>
<address bus='0' target='19' unit='1074872354'/>
</source>
</hostdev>
...trimmed...
Since the reference unit and target fields are used in
several places in the XML schema, create a separate one
specific for SCSI Logical Units that will permit the
greater length. This permits both the validation utility
and the virsh edit command to succeed when a hostdev
tag is included.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1220527
This type of information defines attributes of a system
baseboard. With one exception: board type is yet not implemented
in qemu so it's not introduced here either.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch adds the support of queues attribute of the driver element
for vhost-user interface type. Example:
<interface type='vhostuser'>
<mac address='52:54:00:ee:96:6d'/>
<source type='unix' path='/tmp/vhost2.sock' mode='client'/>
<model type='virtio'/>
<driver queues='4'/>
</interface>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1207692
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Multi != One. And indeed, libvirt behaves the same way for queues='1'
as without such setting. Let's make it clear in the XML.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
qemu 2.3.0 added the -cpu host,aarch64=off option, which allows using
qemu-system-aarch64 KVM to run armv7l VMs.
Add a capabilities check for it, wire it up in qemu_command, and test
the command line generation.
We have been formatting the first serial device also
as a console device, but only if there were no other consoles.
If there is a <serial> device present in the XML, but no serial
<console>, or if there isn't any <console> at all but the domain
definition hasn't gone through a parse->format->parse round-trip,
the <console> device would not be formatted.
Change the code to always add the stub device for the first
serial device.
Fixes https://bugzilla.redhat.com/show_bug.cgi?id=1089914
The guest firmware provides the same functionality as the pvpanic
device, and the relevant element should always be present in the
domain XML to reflect this fact, so add it after parsing the
definition if it wasn't there already.
The guest firmware provides the same functionality as the pvpanic
device, which is not available in QEMU on pSeries, so the domain
XML should be allowed to contain the <panic> element.
On the other hand, unlike the pvpanic device, the guest firmware
can't be configured, so report an error if an address has been
provided in the XML.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182388
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Implementation is pretty straight-forward. Of course, not all qemus
out there supports the device, so new capability is introduced and
checked prior each use of the device.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Like usb-serial, the pci-serial device allows a serial device to be
attached to PCI bus. An example XML looks like this:
<serial type='dev'>
<source path='/dev/ttyS2'/>
<target type='pci-serial' port='0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</serial>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
After parsing the memory device XML the function would not restore the
XML parser context causing invalid XPath starting point for the rest of
the elements. This is a regression since 3e4230d2.
The test case addition uses the <idmap> element that is currently unused
by qemu, but parsed after the memory device definition and formatted
always.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1223631
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Test the support for enabling/disabling CPACF protected key management
operations for a guest.
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
We have previously effectively ignored all <controller type='ide'>
elements in a domain definition.
On the i440fx-based machinetypes there is an IDE controller that is
included in the chipset and can't be removed (which is the ide
controller with index='0'>), so it makes sense to ignore that one
controller. However, if an i440fx domain definition has a 2nd
controller, nothing catches this error (unless you also have a disk
attached to it, in which case qemu will complain that you're trying to
use the ide controller named "ide1", which doesn't exist), and if any
other type of domain has even a single controller defined, it will be
incorrectly ignored.
Ignoring a bogus controller definition isn't such a big problem, as
long as an error is logged when any disk is attached to that
non-existent controller. But in the case of q35-based machinetypes,
the hardcoded id ("alias" in libvirt terms) of its builtin SATA
controller is "ide", which happens to be the same id as the builtin
IDE controller on i440fx machinetypes. So libvirt creates a
commandline believing that it is connecting the disk to the builtin
(but actually nonexistent) IDE controller, qemu thinks that libvirt
wanted that disk connected to the builtin SATA controller, and
everybody is happy.
Until you try to connect a 2nd disk to the IDE controller. Then qemu
will complain that you're trying to set unit=1 on a controller that
requires unit=0 (SATA controllers are organized differently than IDE
controllers).
After this patch, if a domain has an IDE controller defined for a
machinetype that has no IDE controllers, libvirt will log an error
about the controller itself as it is building the qemu commandline
(rather than a (possible) error from qemu about disks attached to that
controller). This is done by adding IDE to the list of controller
types that are handled in the loop that creates controller command
strings in qemuBuildCommandline() (previously it would *always* skip
IDE controllers). Then qemuBuildControllerDevStr() is modified to log
an appropriate error in the case of IDE controllers.
In the future, if we add support for extra IDE controllers (piix3-ide
and/or piix4-ide) we can just add it into the IDE case in
qemuBuildControllerDevStr(). For now, nobody seems anxious to add
extra support for an aging and very slow controller, when there are so
many better options available.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1176071 (Fedora)
Back in 2013, commit 877bc089 added in some tests that made sure no
error was generated on a domain definition that had an automatically
added usb controller if that domain didn't have a PCI bus to attach
the usb controller to. This was done because, at that time, libvirt
was automatically adding a usb controller to *any* domain definition
that didn't have one. Along with permitting the controller, two
s390-specific tests were added to ensure this behavior was maintained
- one with <controller type='usb' model='none'/> and another (called
"s390-piix-controllers") that had both usb and ide controllers, but
nothing attached to them.
Then in February of this year, commit 09ab9dcc eliminated the annoying
auto-adding of a usb device for s390 and s390x machines, stating:
"Since s390 does not support usb the default creation of a usb
controller for a domain should not occur."
Although, as verified here, the s390 doesn't support usb, and usb
controllers aren't currently added to s390 domain definitions
automatically, there are likely still some domain definitions in the
wild that have a usb controller (which was added *by libvirt*, not by
the user), so we will keep the tests verifying that behavior for
now. But this patch changes the names of the tests to reflect that
they don't actually contain a valid s390 config; this way future
developers won't propagate the incorrect idea that an s390 virtual
machine can have a USB (or IDE) bus.
In the case of the IDE controller, though, libvirt has never
automatically added an IDE controller unless a user added an IDE disk
(which itself would have caused an error), and we specifically *do*
want to begin generating an error when someone tries to add an IDE
controller to a domain that can't support one. For that reason, while
renaming the sz390-piix-controllers patch, this patch removes the
<controller type='ide'...> from it (otherwise the upcoming patch would
break make check)
This makes sure that that the commandlines generated for devices and
controller devices are all using the alias that has been set in the
controller's object as the id of the controller, rather than
hardcoding a printf (or worse, encoding exceptions to the standard
${controller}${index} into the logic)
Since this "fixes" the controller name used for the sata controller,
the commandline arg for the sata controller in the sata test case had
to be adjusted to be "sata0" instead of "ahci0". All other tests
remain unchanged, verifying that the patch causes no other functional
change.
Because the function that finds a controller alias based on a device
def requires a pointer to the full domainDef in order to get the list
of controllers, the arglist of a few functions had to have this added.
My commit 747761a79 (v1.2.15 only) dropped this bit of logic when filling
in a default arch in the XML:
- /* First try to find one matching host arch */
- for (i = 0; i < caps->nguests; i++) {
- if (caps->guests[i]->ostype == ostype) {
- for (j = 0; j < caps->guests[i]->arch.ndomains; j++) {
- if (caps->guests[i]->arch.domains[j]->type == domain &&
- caps->guests[i]->arch.id == caps->host.arch)
- return caps->guests[i]->arch.id;
- }
- }
- }
That attempt to match host.arch is important, otherwise we end up
defaulting to i686 on x86_64 host for KVM, which is not intended.
Duplicate it in the centralized CapsLookup function.
Additionally add some testcases that would have caught this.
https://bugzilla.redhat.com/show_bug.cgi?id=1219191
My commit 7b9de914 added some aarch64 CPU test cases. I wanted to test
two different code paths but inadvertently added two of the same test
cases.
The second code path (using <cpu><model>host</model</cpu>) isn't easily
exercised via the qemu tests anyways, I'll need to look elsewhere.
Regardless, remove the redundant tests for now
The only version that's supported in QEMU is version 2, currently.
Fortunately, it is enabled by aarch64 automatically, so there's
nothing for us that needs to be put onto command line.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
With iothreadid's allowing any 'id' value for an iothread_id, the
iothreadsched code needs a slight adjustment to allow for "any"
unsigned int value in order to create the bitmap of ids that will
have scheduler adjustments. Adjusted the doc description as well.
Add 'thread_id' to the virDomainIOThreadIDDef as a means to store the
'thread_id' as returned from the live qemu monitor data.
Remove the iothreadpids list from _qemuDomainObjPrivate and replace with
the new iothreadids 'thread_id' element.
Rather than use the default numbering scheme of 1..number of iothreads
defined for the domain, use the iothreadid's list for the iothread_id
Since iothreadids list keeps track of the iothread_id's, these are
now used in place of the many places where a for loop would "know"
that the ID was "+ 1" from the array element.
The new tests ensure usage of the <iothreadid> values for an exact number
of iothreads and the usage of a smaller number of <iothreadid> values than
iothreads that exist (and usage of the default numbering scheme).
- Make sure aarch64 host-passthrough works correctly
- Make sure libvirt doesn't choke on cpu model=host, which is what
virt-install/virt-manager were incorrectly specifying up until recently.
The PortNumber data type is declared to derive from 'short'.
Unfortunately this is an signed type, so validates the range
[-32,768, 32,767] which excludes valid port numbers between
32767 and 65535.
We can't use 'unsignedShort', since we need -1 to be a valid
port number too.
This change is to use 'int' and set an explicit max boundary
instead of relying on the data types' built-in max.
One of the existing tests is changed to use a high port number
to validate the schema.
https://bugzilla.redhat.com/show_bug.cgi?id=1214664
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
According to docs, using 'lun' as a value for device attribute is only valid
with disk types 'block' and 'network'. However current RNG schema also allows
a combination type='file' device='lun' which results in a successfull
xml validation, but fails at qemuBuildCommandLine.
Besides fixing the RNG schema, this patch also adds a qemuxml2argvtest
for this case.
https://bugzilla.redhat.com/show_bug.cgi?id=1210669
The <inbound/> element to <bandwidth/> has several attributes from
which two are mandatory. Well, from two at least one has to be
present: @average or @floor or both. Instead of inventing crazy RNG
schema, let's make all the attributes optional there and rely on our
parsing code to correctly handle the situation.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Instead of always using controller 0 and incrementing port number,
respect the maximum port numbers of controllers and use all of them.
Ports for virtio consoles are quietly reserved, but not formatted
(neither in XML nor on QEMU command line).
Also rejects duplicate virtio-serial addresses.
https://bugzilla.redhat.com/show_bug.cgi?id=890606https://bugzilla.redhat.com/show_bug.cgi?id=1076708
Test changes:
* virtio-auto.args
Filling out the port when just the controller is specified.
switched from using
maxport + 1
to:
first free port on the controller
* virtio-autoassign.args
Filling out the address when no <address> is specified.
Started using all the controllers instead of 0, also discards
the bus value.
* xml -> xml output of virtio-auto
The port assignment is no longer done as a part of XML parsing,
so the unspecified values stay 0.
On IRC, Hydrar pointed a problem where 'virsh edit' failed on
his domain created through an ISCSI pool managed by virt-manager,
all because the XML included a block device with colons in the
name.
* docs/schemas/basictypes.rng (absFilePath): Add colon as safe.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.xml: New file.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.args: Likewise.
* tests/qemuxml2argvtest.c (mymain): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Starting a qemu VM with a memory module that has the base address
specified results in the following error:
error: internal error: early end of file from monitor: possible problem:
2015-03-26T03:45:52.338891Z qemu-kvm: -device pc-dimm,node=0,memdev=memdimm0,
id=dimm0,slot=0,base=4294967296: Property '.base' not found
The correct property name for the base address is 'addr'.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
QEMU 2.3 adds these new models to cover Haswell and Broadwell CPUs with
updated microcode. Luckily, they also reverted former the machine type
specific changes to existing models. And since these changes were never
released, we don't need to hack around them in libvirt.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Add support to start qemu instance with 'pc-dimm' device. Thanks to the
refactors we are able to reuse the existing function to determine the
parameters.
This patch adds code that parses and formats configuration for memory
devices.
A simple configuration would be:
<memory model='dimm'>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
</memory>
A complete configuration of a memory device:
<memory model='dimm'>
<source>
<pagesize unit='KiB'>4096</pagesize>
<nodemask>1-3</nodemask>
</source>
<target>
<size unit='KiB'>524287</size>
<node>1</node>
</target>
</memory>
This patch preemptively forbids use of the <memory> device in individual
drivers so the users are warned right away that the device is not
supported.
To enable memory hotplug the maximum memory size and slot count need to
be specified. As qemu supports now other units than mebibytes when
specifying memory, use the new interface in this case.
Midonet is an opensource virtual networking that over lays the IP
network between hypervisors. Currently, such networks can be made
with the openvswitch virtualport type.
This patch, defines the schema and documentation that will serve
as basis for the follow up patches that will add support to libvirt
for using Midonet virtual ports for its interfaces. The schema
definition requires that the port profile expresses its interfaceid
as part of the port profile. For that reason, this is part of the
patch too.
Signed-off-by: Antoni Segura Puimedon <toni+libvirt@midokura.com>
Now that the size of guest's memory can be inferred from the NUMA
configuration (if present) make it optional to specify <memory>
explicitly.
To make sure that memory is specified add a check that some form of
memory size was specified. One side effect of this change is that it is
no longer possible to specify 0KiB as memory size for the VM, but I
don't think it would be any useful to do so. (I can imagine embedded
systems without memory, just registers, but that's far from what libvirt
is usually doing).
Forbidding 0 memory for guests also fixes a few corner cases where 0 was
not interpreted correctly and caused failures. (Arguments for numad when
using automatic placement, size of the balloon). This fixes problems
described in https://bugzilla.redhat.com/show_bug.cgi?id=1161461
Test case changes are added to verify that the schema change and code
behave correctly.
Use the NUMA total instead of the configured size both in XML and for
uses in the code once NUMA is enabled for a domain.
One test case change is necessary as the rounding of the individual cell
sizes was not matching the rounding of the total size.
Commit 5aee81a0 introduced a new test for disk-serial. The test fails
on i686 arch because there is no need to add "-cpu qemu32" to command
line. To fix the test update emulator in XML to "/usr/bin/qemu" so we
don't add the "-cpu qemu32" to command while running the test on i686 or
x86_64 host.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
We don't usually do tests purely for one change, but one change was
special because when users will migrate to OVMF/AAVMF, commit 18f9f69b
makes their lives easier by allowing them to interleave <type/> inside
<os/>. It would be nice of us to keep the possibility of them pasting
the loader and nvram elements wherever it is valid, hence this test.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Commit 3e4b783e fixed an issue with RNG schema where this address type
was missing, this commit adds a test for it.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
We have something like pvpanic device. However, in some cases it does
not have any address assigned, in which case we produce this ugly XML
(still valid though):
<devices>
<emulator>/usr/bin/qemu</emulator>
...
<panic>
</panic>
</devices>
Lets format "<panic/>" instead.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There was a mess in the way how we store unlimited value for memory
limits and how we handled values provided by user. Internally there
were two possible ways how to store unlimited value: as 0 value or as
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED. Because we chose to store memory
limits as unsigned long long, we cannot use -1 to represent unlimited.
It's much easier for us to say that everything greater than
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED means unlimited and leave 0 as valid
value despite that it makes no sense to set limit to 0.
Remove unnecessary function virCompareLimitUlong. The update of test
is to prevent the 0 to be miss-used as unlimited in future.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1146539
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Since the APIs support just one element per namespace and while
modifying an element all duplicates would be removed, let's do this
right away in the post parse callback.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1190590
In commit edd1295e1d I've introduced an
XML element that allows to configure state of the network interface
link. Somehow the RNG schema hunk ended up in a weird place in the
network schema definition. Move it to the right place and add a test
case.
Note that the link state is set up via the monitor at VM startup so I
originally didn't think of adding a test case.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1173468
https://bugzilla.redhat.com/show_bug.cgi?id=1142631
This patch resolves a situation where the same "<target dev='$name'...>"
can be used for multiple disks in the domain.
While the $name is "mostly" advisory regarding the expected order that
the disk is added to the domain and not guaranteed to map to the device
name in the guest OS, it still should be unique enough such that other
domblk* type operations can be performed.
Without the patch, the domblklist will list the same Target twice:
$ virsh domblklist $dom
Target Source
------------------------------------------------
sda /var/lib/libvirt/images/file.qcow2
sda /var/lib/libvirt/images/file.img
Additionally, getting domblkstat, domblkerror, domblkinfo, and other block*
type calls will not be able to reference the second target.
Fortunately, hotplug disallows adding a "third" sda value:
$ qemu-img create -f raw /var/lib/libvirt/images/file2.img 10M
$ virsh attach-disk $dom /var/lib/libvirt/images/file2.img sda
error: Failed to attach disk
error: operation failed: target sda already exists
$
BUT, it since 'sdb' doesn't exist one would get the following on the same
hotplug attempt, but changing to use 'sdb' instead of 'sda'
$ virsh attach-disk $dom /var/lib/libvirt/images/file2.img sdb
error: Failed to attach disk
error: internal error: unable to execute QEMU command 'device_add': Duplicate ID 'scsi0-0-1' for device
$
Since we cannot fix this issue at parsing time, the best that can be done so
as to not "lose" a domain is to make the check prior to starting the guest
with the results as follows:
$ virsh start $dom
error: Failed to start domain $dom
error: XML error: target 'sda' duplicated for disk sources '/var/lib/libvirt/images/file.qcow2' and '/var/lib/libvirt/images/file.img'
$
Running 'make check' found a few more instances in the tests where this
duplicated target dev value was being used. These also exhibited some
duplicated 'id=' values (negating the uniqueness argument of aliases) in
the corresponding .args file and of course the *xmlout version of a few
input XML files.
Well, not that we are not formatting invalid XML, rather than not as
beautiful as we can:
<cpu mode='host-passthrough'>
</cpu>
If there are no children, let's use the singleton element.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since s390 does not support usb the default creation of a usb controller
for a domain should not occur.
Also adjust s390 test cases by removing usb device instances since
usb devices are no longer created by default for s390 the s390
test cases need to be adjusted.
Signed-off-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
The mask was stored both as a bitmap and as a string. The string is used
for XML output only. Remove the string, as it can be reconstructed from
the bitmap.
The test change is necessary as the bitmap formatter doesn't "optimize"
using the '^' operator.
So, when building the '-numa' command line, the
qemuBuildMemoryBackendStr() function does quite a lot of checks to
chose the best backend, or to check if one is in fact needed. However,
it returned that backend is needed even for this little fella:
<numatune>
<memory mode="strict" nodeset="0,2"/>
</numatune>
This can be guaranteed via CGroups entirely, there's no need to use
memory-backend-ram to let qemu know where to get memory from. Well, as
long as there's no <memnode/> element, which explicitly requires the
backend. Long story short, we wouldn't have to care, as qemu works
either way. However, the problem is migration (as always). Previously,
libvirt would have started qemu with:
-numa node,memory=X
in this case and restricted memory placement in CGroups. Today, libvirt
creates more complicated command line:
-object memory-backend-ram,id=ram-node0,size=X
-numa node,memdev=ram-node0
Again, one wouldn't find anything wrong with these two approaches.
Both work just fine. Unless you try to migrated from the older libvirt
into the newer one. These two approaches are, unfortunately, not
compatible. My suggestion is, in order to allow users to migrate, lets
use the older approach for as long as the newer one is not needed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In order for QEMU vCPU (and other) threads to run with RT scheduler,
libvirt needs to take care of that so QEMU doesn't have to run privileged.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178986
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
In our RNG schema we do allow multiple (different) seclabels per-domain,
but don't allow this for devices, yet we neither have a check in our XML parser,
nor in a post-parse callback. In that case we should allow multiple
(different) seclabels for devices as well.
Move the alias name right after the object type for rng-egd backend so
that we can later use the JSON to commandline generator to create the
command line.
Libvirt didn't prefix the random number generator backend object alias
with any string thus the device alias and object alias were identical.
To avoid possible problems, rename the alias for the backend object and
tweak tests to comply with the change.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
It is only supported for virtio adapters.
Silently drop it if it was specified for other models,
as is done for other virtio attributes.
Also mention this in the documentation.
https://bugzilla.redhat.com/show_bug.cgi?id=1147195
Change done by commit f309db1f4d wrongly
assumes that qemu can start with a combination of NUMA nodes specified
with the "memdev" option and the appropriate backends, and the legacy
way by specifying only "mem" as a size argument. QEMU rejects such
commandline though:
$ /usr/bin/qemu-system-x86_64 -S -M pc -m 1024 -smp 2 \
-numa node,nodeid=0,cpus=0,mem=256 \
-object memory-backend-ram,id=ram-node1,size=12345 \
-numa node,nodeid=1,cpus=1,memdev=ram-node1
qemu-system-x86_64: -numa node,nodeid=1,cpus=1,memdev=ram-node1: qemu: memdev option must be specified for either all or no nodes
To fix this issue we need to check if any of the nodes requires the new
definition with the backend and if so, then all other nodes have to use
it too.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182467
QEMU's command line visitor as well as the JSON interface take bytes by
default for memory object sizes. Convert mebibytes to bytes so that we
can later refactor the existing code for hotplug purposes.
QEMU's qapi visitor code allows yes/on/y for true and no/off/n for false
value of boolean properities. Unify the used style so that we can
generate it later and fix test cases.
https://bugzilla.redhat.com/show_bug.cgi?id=1170492
In one of our previous commits (dc8b7ce7) we've done a functional
change even though it was intended as pure refactor. The problem is,
that the following XML:
<vcpu placement='static' current='2'>6</vcpu>
<cputune>
<emulatorpin cpuset='1-3'/>
</cputune>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
gets translated into this one:
<vcpu placement='auto' current='2'>6</vcpu>
<cputune>
<emulatorpin cpuset='1-3'/>
</cputune>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
We should not change the vcpu placement mode. Moreover, we're doing
something similar in case of emulatorpin and iothreadpin. If they were
set, but vcpu placement was auto, we've mistakenly removed them from
the domain XML even though we are able to set them independently on
vcpus.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There are some interface types (notably 'server' and 'client')
which instead of allowing the default set of elements and
attributes (like the rest do), try to enumerate only the elements
they know of. This way it's, however, easy to miss something. For
instance, the <address/> element was not mentioned at all. This
resulted in a strange behavior: when such interface was added
into XML, the address was automatically generated by parsing
code. Later, the formatted XML hasn't passed the RNG schema. This
became more visible once we've turned on the XML validation on
domain XML changes: appending an empty line at the end of
formatted XML (to trick virsh think the XML had changed) made
libvirt to refuse the very same XML it formatted.
Instead of trying to find each element and attribute we are
missing in the schema, lets just allow all the elements and
attributes like we're doing that for the rest of types. It's no
harm if the schema is wider than our parser allows.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1130390
The listen address is not mandatory for <interface type='server'>
but when it's not specified, we've been formatting it as:
-netdev socket,listen=(null):5558,id=hostnet0
which failed with:
Device 'socket' could not be initialized
Omit the address completely and only format the port in the listen
attribute.
Also fix the schema to allow specifying a model.
