Fill them in right away rather than having to figure out at runtime
whether they are necessary or not.
virStorageSourceNetworkDefaultPort does not need to be exported any
more.
This patch introduces
<cache level='N' mode='emulate'/>
<cache mode='passthrough'/>
<cache mode='disable'/>
sub element of /domain/cpu. Currently only a single <cache> element is
allowed.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The issue is that if this graphics definition is provided:
<graphics type='vnc' port='0'/>
it's parsed as:
<graphics type='vnc' autoport='no'>
<listen type='address'/>
</graphics>
but if the resulting XML is parsed again the output is:
<graphics type='vnc' port='-1' autoport='yes'>
<listen type='address'/>
</graphics>
and this should not happen. The XML have to always remain the same
after it was already parsed by libvirt.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1383039
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
This patch adds support and documentation for
a generalized hardware cache event called cache_l1d
perf event.
Signed-off-by: Nitesh Konkar <nitkon12@linux.vnet.ibm.com>
With current perf framework, this patch adds support and documentation
for the branch_instructions perf event.
Signed-off-by: Nitesh Konkar <nitkon12@linux.vnet.ibm.com>
With current perf framework, this patch adds support and documentation
for more perf events, including cache misses, cache references, cpu cycles,
and instructions.
Signed-off-by: Qiaowei Ren <qiaowei.ren@intel.com>
Individual vCPU hotplug requires us to track the state of any vCPU. To
allow this add the following XML:
<domain>
...
<vcpu current='2'>3</vcpu>
<vcpus>
<vcpu id='0' enabled='yes' hotpluggable='no' order='1'/>
<vcpu id='1' enabled='yes' hotpluggable='yes' order='2'/>
<vcpu id='1' enabled='no' hotpluggable='yes'/>
</vcpus>
...
The 'enabled' attribute allows to control the state of the vcpu.
'hotpluggable' controls whether given vcpu can be hotplugged and 'order'
allows to specify the order to add the vcpus.
VNC graphics already supports sockets but only via 'socket' attribute.
This patch coverts that attribute into listen type 'socket'.
For backward compatibility we need to handle listen type 'socket' and 'socket'
attribute properly to support old XMLs and new XMLs. If both are provided they
have to match, if only one of them is provided we need to be able to parse that
configuration too.
To not break migration back to old libvirt if the socket is provided by user we
need to generate migratable XML without the listen element and use only 'socket'
attribute.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Trying to define a domain name containing an embedded '/'
will immediately fail when trying to write the XML to disk for
our stateful drivers. This patch explicitly rejects names
containing a '/', and provides an xmlopt feature for drivers
to avoid this validation check, which is enabled in every
non-stateful driver that already has xmlopt handling wired up.
(Technically this could reject a previously accepted vmname like
'/foo', however at least for the qemu driver that falls over
later when starting qemu)
https://bugzilla.redhat.com/show_bug.cgi?id=639923
* Add a test for listen=XXX and <listen address=YYY/> collision error
* Add an explicit test for listen=XXX duplicated to <listen address=XXX/>
We implicitly test it elsewhere but I figure it's better to be explicit,
and this test case can be extended in the future for additional listen
back compat if/when we support <listen type='socket'/> syntax
