If a domain started with -no-shutdown shuts down while libvirtd is not
running, it will be seen as paused when libvirtd reconnects to it. Use
the paused reason to detect if a domain was stopped because of shutdown
and finish the process just as if a SHUTDOWN event is delivered from
qemu.
This patch was made in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=738095
In short, qemu's default for the rombar setting (which makes the
firmware ROM of a PCI device visible/not on the guest) was previously
0 (not visible), but they recently changed the default to 1
(visible). Unfortunately, there are some PCI devices that fail in the
guest when rombar is 1, so the setting must be exposed in libvirt to
prevent a regression in behavior (it will still require explicitly
setting <rom bar='off'/> in the guest XML).
rombar is forced on/off by adding:
<rom bar='on|off'/>
inside a <hostdev> element that defines a PCI device. It is currently
ignored for all other types of devices.
At the moment there is no clean method to determine whether or not the
rombar option is supported by QEMU - this patch uses the advice of a
QEMU developer to assume support for qemu-0.12+. There is currently a
patch in the works to put this information in the output of "qemu-kvm
-device pci-assign,?", but of course if we switch to keying off that,
we would lose support for setting rombar on all the versions of qemu
between 0.12 and whatever version gets that patch.
SIGTERM handling for -no-shutdown is already fixed in qemu git and
libvirt can safely use it. The downside is that 0.15.50 version of qemu
can be any qemu compiled from git, even that without the fix for
SIGTERM. However, I think this patch is worth it since excluding 0.15.50
from the check makes testing current qemu with libvirt much easier and
someone running qemu from git should be able to rebuild fixed qemu from
git if they hit the problem with a hang on shutdown.
QEMU 0.13 introduced cache=unsafe for -drive, this patch exposes
it in the libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_UNSAFE),
as even if $prefix_CACHE_V2 is set, we can't know if unsafe
is supported.
* Improved the reliability of qemu cache type detection.
If a domain has inactive XML we want to transfer it to destination
when migrating with VIR_MIGRATE_PERSIST_DEST. In order to harm
the migration protocol as least as possible, a optional cookie was
chosen.
The previous patch removed all snapshots, but not the directory
where the snapshots lived, which is still a form of stale data.
* src/qemu/qemu_domain.c (qemuDomainRemoveInactive): Wipe any
snapshot directory.
Commit 282fe1f0 documented that transient domains will auto-delete
any snapshot metadata when the last reference to the domain is
removed, and that management apps are in charge of grabbing any
snapshot metadata prior to that point. However, this was not
actually implemented for qemu until now.
* src/qemu/qemu_driver.c (qemudDomainCreate)
(qemuDomainDestroyFlags, qemuDomainSaveInternal)
(qemudDomainCoreDump, qemuDomainRestoreFlags, qemudDomainDefine)
(qemuDomainUndefineFlags, qemuDomainMigrateConfirm3)
(qemuDomainRevertToSnapshot): Clean up snapshot metadata.
* src/qemu/qemu_migration.c (qemuMigrationPrepareAny)
(qemuMigrationPerformJob, qemuMigrationPerformPhase)
(qemuMigrationFinish): Likewise.
* src/qemu/qemu_process.c (qemuProcessHandleMonitorEOF)
(qemuProcessReconnect, qemuProcessReconnectHelper)
(qemuProcessAutoDestroyDom): Likewise.
This patch is mostly code motion - moving some functions out
of qemu_driver and into qemu_domain so they can be reused by
multiple qemu_* files (since qemu_driver.h must not grow).
It also adds a new helper function, qemuDomainRemoveInactive,
which will be used in the next patch.
* src/qemu/qemu_domain.h (qemuFindQemuImgBinary)
(qemuDomainSnapshotWriteMetadata, qemuDomainSnapshotForEachQcow2)
(qemuDomainSnapshotDiscard, qemuDomainSnapshotDiscardAll)
(qemuDomainRemoveInactive): New prototypes.
(struct qemu_snap_remove): New struct.
* src/qemu/qemu_domain.c (qemuDomainRemoveInactive)
(qemuDomainSnapshotDiscardAllMetadata): New functions.
(qemuFindQemuImgBinary, qemuDomainSnapshotWriteMetadata)
(qemuDomainSnapshotForEachQcow2, qemuDomainSnapshotDiscard)
(qemuDomainSnapshotDiscardAll): Move here...
* src/qemu/qemu_driver.c (qemuFindQemuImgBinary)
(qemuDomainSnapshotWriteMetadata, qemuDomainSnapshotForEachQcow2)
(qemuDomainSnapshotDiscard, qemuDomainSnapshotDiscardAll): ...from
here.
(qemuDomainUndefineFlags): Update caller.
* src/conf/domain_conf.c (virDomainRemoveInactive): Doc fixes.
Commit 19f8c98 introduced VIR_DOMAIN_UNDEFINE_SNAPSHOTS_METADATA,
with the intent that omitting the flag makes undefine fail, and
including the flag deletes metadata. But it used the wrong logic.
Also, hoist the transient domain sooner, so that we don't
accidentally remove metadata of a transient domain.
* src/qemu/qemu_driver.c (qemuDomainUndefineFlags): Check correct
flag value.
* src/qemu/qemu_process.c: Taking if (qemuDomainObjEndJob(driver, obj) == 0)
true branch then 'obj' is NULL, virDomainObjIsActive(obj) and
virDomainObjUnref(obj) will dereference NULL pointer.
Signed-off-by: Alex Jia <ajia@redhat.com>
Once virDomainReboot is called for a domain, guest OS initiated shutdown
would always result in reboot instead of shutdown. Only
virDomainShutdown would actually shutd such domain down. That's because
we forgot to reset fakeReboot flag once we asked the domain to reboot.
The commit that prevents disk corruption on domain shutdown
(96fc478417) causes regression with QEMU
0.14.* and 0.15.* because of a regression bug in QEMU that was fixed
only recently in QEMU git. The affected versions of QEMU do not quit on
SIGTERM if started with -no-shutdown, which we use to implement fake
reboot. Since -no-shutdown tells QEMU not to quit automatically on guest
shutdown, domains started using the affected QEMU cannot be shutdown
properly and stay in a paused state.
This patch disables fake reboot feature on such QEMU by not using
-no-shutdown, which makes shutdown work as expected. However,
virDomainReboot will not work in this case and it will report "Requested
operation is not valid: Reboot is not supported with this QEMU binary".
gcc warns when building libvirt 0.9.5 on a 32-bit machine:
qemu/qemu_migration.c: In function 'qemuMigrationToFile':
qemu/qemu_migration.c:2727:38: error: large integer implicitly truncated to unsigned type [-Woverflow]
* src/qemu/qemu_domain.h (QEMU_DOMAIN_FILE_MIG_BANDWIDTH_MAX): Cap
to long when building for 32-bit platform.
Virsh man page lists driver types to be used with attach-device
command, but does not specify that those are usable only with the XEN
Hypervisor.
This patch adds statement, that those options specified are applicable
only on the Xen hypervisor and adds option usable with qemu emulator.
This patch also changes type of error returned by QEMU driver if the
user specifies incompatible driver type from VIR_ERR_INTERNAL_ERROR to
VIR_ERR_CONFIG_UNSUPPORTED.
For all types of disks other than qcow2, we were requesting that
SELinux labeling visit the new file as if it were qcow2, which
means labeling would try to find the backing files of an empty file.
And for a pre-existing qcow2 disk, we were passing NULL, which meant
that labelling tried to probe the file type (and if probing is
disabled, per the default qemu.conf, this made snapshots fail).
What we really want is to make SELinux labeling visit the new
file as raw; it will later be converted to qcow2 if qemu successfully
made the snapshot.
* src/qemu/qemu_driver.c
(qemuDomainSnapshotCreateSingleDiskActive): Force SELinux labeling
to avoid probe of new file.
For external snapshots to be useful on persistent domains, we must
alter the persistent definition alongside the running definition.
Thanks to the possibility of disk hotplug as well as of edits that
only affect the persistent xml, we can't assume that vm->def and
vm->newDef have the same disk at the same index, so we can only
update the persistent copy if the device destination matches up.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateDiskActive)
(qemuDomainSnapshotCreateSingleDiskActive): Also affect newDef, if
present.
Qemu sends STOP event as part of the shutdown process. Detect such STOP
event and consider shutdown to be reason of emitting such event. That's
the best we can do until qemu provides us the reason directly in STOP
event. This allows us to report shutdown reason for paused state so that
apps can detect domains that failed to finish the shutdown process
(e.g., because qemu is buggy and doesn't exit on SIGTERM or it is
blocked in flushing disk buffers).
Ever since we introduced fake reboot, we call qemuProcessKill as a
reaction to SHUTDOWN event. Unfortunately, qemu doesn't guarantee it
flushed all internal buffers before sending SHUTDOWN, in which case
killing the process forcibly may result in (virtual) disk corruption.
By sending just SIGTERM without SIGKILL we give qemu time to to flush
all buffers and exit. Once qemu exits, we will see an EOF on monitor
connection and tear down the domain. In case qemu ignores SIGTERM or
just hangs there, the process stays running but that's not any different
from a possible hang anytime during the shutdown process so I think it's
just fine.
Also qemu (since 0.14 until it's fixed) has a bug in SIGTERM processing
which causes it not to exit but instead send new SHUTDOWN event and keep
waiting. I think the best we can do is to ignore duplicate SHUTDOWN
events to avoid a SHUTDOWN-SIGTERM loop and leave the domain in paused
state.
When a domain is rebooted using libvirt API, we use fake reboot
consisting of shutting down and resetting the domain. Thus we see a
SHUTDOWN event and set gotShutdown flag. But we never reset it back and
if the domain crashes after it was rebooted this way, we consider it was
a normal shutdown and not a crash.
Commit 4454a9efc7 changed shutoff reason
from VIR_DOMAIN_SHUTOFF_CRASHED to VIR_DOMAIN_SHUTOFF_FAILED in case we
see an unexpected EOF on monitor connection. But FAILED reason is
dedicated for domains that fail to start. CRASHED reason is the right
one to use in this situation.
This patch fixes the bug shown in bugzilla 738778. It's not an nwfilter problem but a connection sharing / closure issue.
https://bugzilla.redhat.com/show_bug.cgi?id=738778
Depending on the speed / #CPUs of the machine you are using you may not see this bug all the time.
Adjust qemuMigrationRun() to use migMaxBandwidth in qemuDomainObjPrivate
structure when setting qemu migration speed. Caller-specified 'resource'
parameter overrides migMaxBandwidth.
The qemu migration speed default is 32MiB/s as defined in migration.c
/* Migration speed throttling */
static int64_t max_throttle = (32 << 20);
There's no need to throttle migration when targeting a file, so set migration
speed to unlimited prior to migration, and restore to libvirt default value
after migration.
Default units is MB for migrate_set_speed monitor command, so
(INT64_MAX / (1024 * 1024)) is used for unlimited migration speed.
Tested with both json and text monitors.
Now that migration speed is stored in qemuDomainObjPrivate structure,
save the new value when invoking qemuDomainMigrateSetMaxSpeed().
Allow setting migration speed on inactive domain too.
The maximum bandwidth that can be consumed when migrating a domain
is better classified as an operational vs configuration parameter of
the dommain. As such, store this parameter in qemuDomainObjPrivate
structure.
Commit 498d783 cleans up some of virtual file names for parsing strings
in memory. This patch cleans up (hopefuly) the rest forgotten by the
first patch.
This patch also changes all of the previously modified "filenames" to
valid URI's replacing spaces for underscores.
Changes to v1:
- Replace all spaces for underscores, so that the strings form valid
URI's
- Replace spaces in places changed by commit 498d783
Regression introduced in commit 3881a470, due to an improper rebase
of a cleanup written beforehand but only applied after a rebased of
a refactoring that created a new function in commit 25fb3ef.
Also avoids passing NULL to printf %s.
* src/qemu/qemu_driver.c: In qemuDomainSnapshotForEachQcow2()
it free up the memory of qemu_driver->qemuImgBinary in the
cleanup tag which leads to the garbage value of qemuImgBinary
in qemu_driver struct and libvirtd crash when running
"virsh snapshot-create" command a second time.
Signed-off-by: Eric Blake <eblake@redhat.com>
Regression introduced in commit 89b6284fd, due to an incorrect
conversion to the new means of converting disk names back to
the correct object.
* src/qemu/qemu_driver.c (qemuDomainGetBlockInfo): Avoid NULL deref.
This patch enables modifying network device configuration using the
virUpdateDeviceFlags API method. Matching of devices is accomplished
using MAC addresses.
While updating live configuration of a running domain, the user is
allowed only to change link state of the interface. Additional
modifications may be added later. For now the code checks for
unsupported changes and thereafter changes the link state, if
applicable.
When updating persistent configuration of guest's network interface the
whole configuration (except for the MAC address) may be modified and
is stored for the next startup.
* src/qemu/qemu_driver.c - Add dispatching of virUpdateDevice for
network devices update (live/config)
* src/qemu/qemu_hotplug.c - add setting of initial link state on live
device addition
- add function to change network device
configuration. By now it supports only
changing of link state
* src/qemu/qemu_hotplug.h - Headers to above functions
* src/qemu/qemu_process.c - set link states before virtual machine
start. Qemu does not support setting of
this on the command line.
This patch adds handlers for modification of guest's interface
link state. Both HMP and QMP commands are supported, but as the
link state functionality is from the beginning supported in QMP
the HMP code will probably never be used.
The mainly changes are:
1) Update qemuMonitorGetBlockStatsInfo and it's children (Text/JSON)
functions to return the value of new latency fields.
2) Add new function qemuMonitorGetBlockStatsParamsNumber, which is
to count how many parameters the underlying QEMU supports.
3) Update virDomainBlockStats in src/qemu/qemu_driver.c to be
compatible with the changes by 1).
If libvirt daemon gets restarted and there is (at least) one
unresponsive qemu, the startup procedure hangs up. This patch creates
one thread per vm in which we try to reconnect to monitor. Therefore,
blocking in one thread will not affect other APIs.
This patch creates an optional BeginJob queue size limit. When
active, all other attempts above level will fail. To set this
feature assign desired value to max_queued variable in qemu.conf.
Setting it to 0 turns it off.
This patch annotates APIs with low or high priority.
In low set MUST be all APIs which might eventually access monitor
(and thus block indefinitely). Other APIs may be marked as high
priority. However, some must be (e.g. domainDestroy).
For high priority calls (HPC), there are some high priority workers
(HPW) created in the pool. HPW can execute only HPC, although normal
worker can process any call regardless priority. Therefore, only those
APIs which are guaranteed to end in reasonable small amount of time
can be marked as HPC.
The size of this HPC pool is static, because HPC are expected to end
quickly, therefore jobs assigned to this pool will be served quickly.
It can be configured in libvirtd.conf via prio_workers variable.
Default is set to 5.
To mark API with low or high priority, append priority:{low|high} to
it's comment in src/remote/remote_protocol.x. This is similar to
autogen|skipgen. If not marked, the generator assumes low as default.
With this, it is now possible to create external snapshots even
when SELinux is enforcing, and to protect the new file with a
lock manager.
* src/qemu/qemu_driver.c
(qemuDomainSnapshotCreateSingleDiskActive): Create and register
new file with proper permissions and locks.
(qemuDomainSnapshotCreateDiskActive): Update caller.
Lots of earlier patches led up to this point - the qemu snapshot_blkdev
monitor command can now be controlled by libvirt! Well, insofar as
SELinux doesn't prevent qemu from open(O_CREAT) on the files. There's
still some followup work before things work with SELinux enforcing,
but this patch is big enough to post now.
There's still room for other improvements, too (for example, taking a
disk snapshot of an inactive domain, by using qemu-img for both internal
and external snapshots; wiring up delete and revert control, including
additional flags from my RFC; supporting active QED disk snapshots;
supporting per-storage-volume snapshots such as LVM or btrfs snapshots;
etc.). But this patch is the one that proves the new XML works!
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Wire in
active disk snapshots.
(qemuDomainSnapshotDiskPrepare)
(qemuDomainSnapshotCreateDiskActive)
(qemuDomainSnapshotCreateSingleDiskActive): New functions.
No one uses this yet, but it will be important once
virDomainSnapshotCreateXML learns a VIR_DOMAIN_SNAPSHOT_DISK_ONLY
flag, and the xml allows passing in the new file names.
* src/qemu/qemu_monitor.h (qemuMonitorDiskSnapshot): New prototype.
* src/qemu/qemu_monitor_text.h (qemuMonitorTextDiskSnapshot):
Likewise.
* src/qemu/qemu_monitor_json.h (qemuMonitorJSONDiskSnapshot):
Likewise.
* src/qemu/qemu_monitor.c (qemuMonitorDiskSnapshot): New
function.
* src/qemu/qemu_monitor_json.c (qemuMonitorJSONDiskSnapshot):
Likewise.
Snapshots alter the set of disk image files opened by qemu, so
they must be audited. But they don't involve a full disk definition
structure, just the new filename. Make the next patch easier by
refactoring the audit routines to just operate on file name.
* src/conf/domain_audit.h (virDomainAuditDisk): Update prototype.
* src/conf/domain_audit.c (virDomainAuditDisk): Act on strings,
not definition structures.
(virDomainAuditStart): Update caller.
* src/qemu/qemu_hotplug.c (qemuDomainChangeEjectableMedia)
(qemuDomainAttachPciDiskDevice, qemuDomainAttachSCSIDisk)
(qemuDomainAttachUsbMassstorageDevice)
(qemuDomainDetachPciDiskDevice, qemuDomainDetachDiskDevice):
Likewise.
My RFC for snapshot support [1] proposes several rules for when it is
safe to delete or revert to an external snapshot, predicated on
the existence of new API flags. These will be incrementally added
in future patches, but until then, blindly mishandling a disk
snapshot risks corrupting internal state, so it is better to
outright reject the attempts until the other pieces are in place,
thus incrementally relaxing the restrictions added in this patch.
[1] https://www.redhat.com/archives/libvir-list/2011-August/msg00361.html
* src/qemu/qemu_driver.c (qemuDomainSnapshotCountExternal): New
function.
(qemuDomainUndefineFlags, qemuDomainSnapshotDelete): Use it to add
safety valve.
(qemuDomainRevertToSnapshot, qemuDomainSnapshotCreateXML): Add safety
valve.
Prior to this patch, <domainsnapshot>/<disks> was ignored. This
changes it to be an error unless an explicit disk snapshot is
requested (a future patch may relax things if it turns out to
be useful to have a <disks> specification alongside a system
checkpoint).
* include/libvirt/libvirt.h.in
(VIR_DOMAIN_SNAPSHOT_CREATE_DISK_ONLY): New flag.
* src/libvirt.c (virDomainSnapshotCreateXML): Document it.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML): Disk
snapshots not supported yet.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Likewise.
I got confused when 'virsh domblkinfo dom disk' required the
path to a disk (which can be ambiguous, since a single file
can back multiple disks), rather than the unambiguous target
device name that I was using in disk snapshots. So, in true
developer fashion, I went for the best of both worlds - all
interfaces that operate on a disk (aka block) now accept
either the target name or the unambiguous path to the backing
file used by the disk.
* src/conf/domain_conf.h (virDomainDiskIndexByName): Add
parameter.
(virDomainDiskPathByName): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainDiskIndexByName): Also allow
searching by path, and decide whether ambiguity is okay.
(virDomainDiskPathByName): New function.
(virDomainDiskRemoveByName, virDomainSnapshotAlignDisks): Update
callers.
* src/qemu/qemu_driver.c (qemudDomainBlockPeek)
(qemuDomainAttachDeviceConfig, qemuDomainUpdateDeviceConfig)
(qemuDomainGetBlockInfo, qemuDiskPathToAlias): Likewise.
* src/qemu/qemu_process.c (qemuProcessFindDomainDiskByPath):
Likewise.
* src/libxl/libxl_driver.c (libxlDomainAttachDeviceDiskLive)
(libxlDomainDetachDeviceDiskLive, libxlDomainAttachDeviceConfig)
(libxlDomainUpdateDeviceConfig): Likewise.
* src/uml/uml_driver.c (umlDomainBlockPeek): Likewise.
* src/xen/xend_internal.c (xenDaemonDomainBlockPeek): Likewise.
* docs/formatsnapshot.html.in: Update documentation.
* tools/virsh.pod (domblkstat, domblkinfo): Likewise.
* docs/schemas/domaincommon.rng (diskTarget): Tighten pattern on
disk targets.
* docs/schemas/domainsnapshot.rng (disksnapshot): Update to match.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: Update test.
Since a snapshot is fully recoverable, it is useful to have a
snapshot as a means of hibernating a guest, then reverting to
the snapshot to wake the guest up. This mode of usage is
similar to 'virsh save/virsh restore', except that virsh
save uses an external file while virsh snapshot keeps the
vm state internal to a qcow2 file. However, it only works on
persistent domains.
In the usage pattern of snapshot/revert for hibernating a guest,
there is no need to keep the guest running between the two points
in time, especially since that would generate runtime state that
would just be discarded. Add a flag to make it possible to
stop the domain after the snapshot has completed.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_SNAPSHOT_CREATE_HALT):
New flag.
* src/libvirt.c (virDomainSnapshotCreateXML): Document it.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML)
(qemuDomainSnapshotCreateActive): Implement it.
Reverting to a state prior to an external snapshot risks
corrupting any other branches in the snapshot hierarchy that
were using the snapshot as a read-only backing file. So
disk snapshot code will default to preventing reverting to
a snapshot that has any children, meaning that deleting just
the children of a snapshot becomes a useful operation in
preparing that snapshot for being a future reversion target.
The code for the new flag is simple - it's one less deletion,
plus a tweak to keep the current snapshot correct.
* include/libvirt/libvirt.h.in
(VIR_DOMAIN_SNAPSHOT_DELETE_CHILDREN_ONLY): New flag.
* src/libvirt.c (virDomainSnapshotDelete): Document it, and
enforce mutual exclusion.
* src/qemu/qemu_driver.c (qemuDomainSnapshotDelete): Implement
it.
The previous patch introduced new config, but if a hypervisor does
not support that new config, someone can write XML that does not
behave as documented. This prevents some of those cases by
explicitly rejecting transient disks for several hypervisors.
Disk snapshots will require a new flag to actually affect a snapshot
creation, so there's not much to reject there.
* src/qemu/qemu_command.c (qemuBuildDriveStr): Reject transient
disks for now.
* src/libxl/libxl_conf.c (libxlMakeDisk): Likewise.
* src/xenxs/xen_sxpr.c (xenFormatSxprDisk): Likewise.
* src/xenxs/xen_xm.c (xenFormatXMDisk): Likewise.
When reverting to a snapshot, the inactive domain configuration
has to be rolled back to what it was at the time of the snapshot.
Additionally, if the VM is active and the snapshot was active,
this now adds a failure if the two configurations are ABI
incompatible, rather than risking qemu confusion.
A future patch will add a VIR_DOMAIN_SNAPSHOT_FORCE flag, which
will be required for two risky code paths - reverting to an
older snapshot that lacked full domain information, and reverting
from running to a live snapshot that requires starting a new qemu
process. Any reverting that stops a running vm is also a form
of data loss (discarding the current running state to go back in
time), but as that is what reversion usually implies, it is
probably not worth requiring a force flag.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Copy out
domain.
(qemuDomainSnapshotCreateXML, qemuDomainRevertToSnapshot): Perform
ABI compatibility checks.
Just like VM saved state images (virsh save), snapshots MUST
track the inactive domain xml to detect any ABI incompatibilities.
The indentation is not perfect, but functionality comes before form.
Later patches will actually supply a full domain; for now, this
wires up the storage to support one, but doesn't ever generate one
in dumpxml output.
Happily, libvirt.c was already rejecting use of VIR_DOMAIN_XML_SECURE
from read-only connections, even though before this patch, there was
no information to be secured by the use of that flag.
And while we're at it, mark the libvirt snapshot metadata files
as internal-use only.
* src/libvirt.c (virDomainSnapshotGetXMLDesc): Document flag.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Add member.
(virDomainSnapshotDefParseString, virDomainSnapshotDefFormat):
Update signature.
* src/conf/domain_conf.c (virDomainSnapshotDefFree): Clean up.
(virDomainSnapshotDefParseString): Optionally parse domain.
(virDomainSnapshotDefFormat): Output full domain.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML)
(esxDomainSnapshotGetXMLDesc): Update callers.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML)
(vboxDomainSnapshotGetXMLDesc): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML)
(qemuDomainSnapshotLoad, qemuDomainSnapshotGetXMLDesc)
(qemuDomainSnapshotWriteMetadata): Likewise.
* docs/formatsnapshot.html.in: Rework doc example.
Based on a patch by Philipp Hahn.
Migration is another case of stranding metadata. And since
snapshot metadata is arbitrarily large, there's no way to
shoehorn it into the migration cookie of migration v3.
This patch consolidates two existing locations for migration
validation into one helper function, then enhances that function
to also do the new checks. If we could always trust the source
to validate migration, then the destination would not have to
do anything; but since older servers that did not do checking
can migrate to newer destinations, we have to repeat some of
the same checks on the destination; meanwhile, we want to
detect failures as soon as possible. With migration v2, this
means that validation will reject things at Prepare on the
destination if the XML exposes the problem, otherwise at Perform
on the source; with migration v3, this means that validation
will reject things at Begin on the source, or if the source
is old and the XML exposes the problem, then at Prepare on the
destination.
This patch is necessarily over-strict. Once a later patch
properly handles auto-cleanup of snapshot metadata on the
death of a transient domain, then the only time we actually
need snapshots to prevent migration is when using the
--undefinesource flag on a persistent source domain.
It is possible to recreate snapshot metadata on the destination
with VIR_DOMAIN_SNAPSHOT_CREATE_REDEFINE and
VIR_DOMAIN_SNAPSHOT_CREATE_CURRENT. But for now, that is limited,
since if we delete the snapshot metadata prior to migration,
then we won't know the name of the current snapshot to pass
along; and if we delete the snapshot metadata after migration
and use the v3 migration cookie to pass along the name of the
current snapshot, then we need a way to bypass the fact that
this patch refuses migration with snapshot metadata present.
So eventually, we may have to introduce migration protocol v4
that allows feature negotiation and an arbitrary number of
handshake exchanges, so as to pass as many rpc calls as needed
to transfer all the snapshot xml hierarchy.
But all of that is thoughts for the future; for now, the best
course of action is to quit early, rather than get into a
funky state of stale metadata; then relax restrictions later.
* src/qemu/qemu_migration.h (qemuMigrationIsAllowed): Make static.
* src/qemu/qemu_migration.c (qemuMigrationIsAllowed): Alter
signature, and allow checks for both outgoing and incoming.
(qemuMigrationBegin, qemuMigrationPrepareAny)
(qemuMigrationPerformJob): Update callers.
A nice benefit of deleting all snapshots at undefine time is that
you don't have to do any reparenting or subtree identification - since
everything goes, this is an O(n) process, whereas using multiple
virDomainSnapshotDelete calls would be O(n^2) or worse. But it is
only doable for snapshot metadata, where we are in control of the
data being deleted; for the actual snapshots, there's too much
likelihood of something going wrong, and requiring even more API
calls to figure out what failed in the meantime, so callers are
better off deleting the snapshot data themselves one snapshot at
a time where they can deal with failures as they happen.
* src/qemu/qemu_driver.c (qemuDomainUndefineFlags): Honor new flags.
As more clients start to want to know this information, doing
a PATH stat walk and malloc for every client adds up.
We are only caching the location, not the capabilities, so even
if qemu-img is updated in the meantime, it will still probably
live in the same location. So there is no need to worry about
clearing this particular cache.
* src/qemu/qemu_conf.h (qemud_driver): Add member.
* src/qemu/qemu_driver.c (qemudShutdown): Cleanup.
(qemuFindQemuImgBinary): Add an argument, and cache result.
(qemuDomainSnapshotForEachQcow2, qemuDomainSnapshotDiscard)
(qemuDomainSnapshotCreateInactive, qemuDomainSnapshotRevertInactive)
(qemuDomainSnapshotCreateXML, qemuDomainRevertToSnapshot): Update
callers.
Just as leaving managed save metadata behind can cause problems
when creating a new domain that happens to collide with the name
of the just-deleted domain, the same is true of leaving any
snapshot metadata behind. For safety sake, extend the semantic
change of commit b26a9fa9 to also cover snapshot metadata as a
reason to reject undefining an inactive domain. A future patch
will make sure that shutdown of a transient domain automatically
deletes snapshot metadata (whether by destroy, shutdown, or
guest-initiated action). Management apps of transient domains
should take care to capture xml of snapshots, if it is necessary
to recreate the snapshot metadata on a later transient domain
with the same name and uuid.
This also documents a new flag that hypervisors can choose to
support as a shortcut for taking care of the metadata as part of
the undefine process; however, nontrivial driver support for these
flags will be deferred to future patches.
Note that ESX and VBox can never be transient; therefore, they
do not have to worry about automatic cleanup after shutdown
(the persistent domain still remains); likewise they never
store snapshot metadata, so the undefine flag is trivial.
The nontrivial work remaining is thus in the qemu driver.
* include/libvirt/libvirt.h.in
(VIR_DOMAIN_UNDEFINE_SNAPSHOTS_METADATA): New flag.
* src/libvirt.c (virDomainUndefine, virDomainUndefineFlags):
Document new limitations and flag.
* src/esx/esx_driver.c (esxDomainUndefineFlags): Trivial
implementation.
* src/vbox/vbox_tmpl.c (vboxDomainUndefineFlags): Likewise.
* src/qemu/qemu_driver.c (qemuDomainUndefineFlags): Enforce
the limitations.
Redefining a qemu snapshot requires a bit of a tweak to the common
snapshot parsing code, but the end result is quite nice.
Be careful that redefinitions do not introduce circular parent
chains. Also, we don't want to allow conversion between online
and offline existing snapshots. We could probably do some more
validation for snapshots that don't already exist to make sure
they are even feasible, by parsing qemu-img output, but that
can come later.
* src/conf/domain_conf.h (virDomainSnapshotParseFlags): New
internal flags.
* src/conf/domain_conf.c (virDomainSnapshotDefParseString): Alter
signature to take internal flags.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML): Update caller.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Support
new public flags.
Supporting NO_METADATA on snapshot creation is interesting - we must
still return a valid opaque snapshot object, but the user can't get
anything out of it (unless we add a virDomainSnapshotGetName()),
since it is no longer registered with the domain.
Also, virsh now tries to query for secure xml, in anticipation of
when we store <domain> xml inside <domainsnapshot>; for now, we
can trivially support it, since we have nothing secure.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Support
new flag.
(qemuDomainSnapshotGetXMLDesc): Trivially support VIR_DOMAIN_XML_SECURE.
To make it easier to know when undefine will fail because of existing
snapshot metadata, we need to know how many snapshots have metadata.
Also, it is handy to filter the list of snapshots to just those that
have no parents; document that flag now, but implement it in later patches.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_SNAPSHOT_LIST_ROOTS)
(VIR_DOMAIN_SNAPSHOT_LIST_METADATA): New flags.
* src/libvirt.c (virDomainSnapshotNum)
(virDomainSnapshotListNames): Document them.
* src/esx/esx_driver.c (esxDomainSnapshotNum)
(esxDomainSnapshotListNames): Implement trivial flag.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotNum)
(vboxDomainSnapshotListNames): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotNum)
(qemuDomainSnapshotListNames): Likewise.
Adding this was trivial compared to the previous patch for fixing
qemu snapshot deletion in the first place.
* src/qemu/qemu_driver.c (qemuDomainSnapshotDiscard): Add
parameter.
(qemuDomainSnapshotDiscardDescendant, qemuDomainSnapshotDelete):
Update callers.
Similar to the last patch in isolating the filtering from the
client actions, so that clients don't have to reinvent the
filtering.
* src/conf/domain_conf.h (virDomainSnapshotForEachChild): New
prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainSnapshotActOnChild)
(virDomainSnapshotForEachChild): New functions.
(virDomainSnapshotCountChildren): Delete.
(virDomainSnapshotHasChildren): Simplify.
* src/qemu/qemu_driver.c (qemuDomainSnapshotReparentChildren)
(qemuDomainSnapshotDelete): Likewise.
Deleting a snapshot and all its descendants had problems with
tracking the current snapshot. The deletion does not necessarily
proceed in depth-first order, so a parent could be deleted
before a child, wreaking havoc on passing the notion of the
current snapshot to the parent. Furthermore, even if traversal
were depth-first, doing multiple file writes to pass current up
the chain one snapshot at a time is wasteful, comparing to a
single update to the current snapshot at the end of the algorithm.
* src/qemu/qemu_driver.c (snap_remove): Add field.
(qemuDomainSnapshotDiscard): Add parameter.
(qemuDomainSnapshotDiscardDescendant): Adjust accordingly.
(qemuDomainSnapshotDelete): Properly reset current.
This one's nasty. Ever since we fixed virHashForEach to prevent
nested hash iterations for safety reasons (commit fba550f6),
virDomainSnapshotDelete with VIR_DOMAIN_SNAPSHOT_DELETE_CHILDREN
has been broken for qemu: it deletes children, while leaving
grandchildren intact but pointing to a no-longer-present parent.
But even before then, the code would often appear to succeed to
clean up grandchildren, but risked memory corruption if you have
a large and deep hierarchy of snapshots.
For acting on just children, a single virHashForEach is sufficient.
But for acting on an entire subtree, it requires iteration; and
since we declared recursion as invalid, we have to switch to a
while loop. Doing this correctly requires quite a bit of overhaul,
so I added a new helper function to isolate the algorithm from the
actions, so that callers do not have to reinvent the iteration.
Note that this _still_ does not handle CHILDREN correctly if one
of the children is the current snapshot; that will be next.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Add mark.
(virDomainSnapshotForEachDescendant): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainSnapshotMarkDescendant)
(virDomainSnapshotActOnDescendant)
(virDomainSnapshotForEachDescendant): New functions.
* src/qemu/qemu_driver.c (qemuDomainSnapshotDiscardChildren):
Replace...
(qemuDomainSnapshotDiscardDescenent): ...with callback that
doesn't nest hash traversal.
(qemuDomainSnapshotDelete): Use new function.
For a system checkpoint of a running or paused domain, it's fairly
easy to honor new flags for altering which state to use after the
revert. For an inactive snapshot, the revert has to be done while
there is no qemu process, so do back-to-back transitions; this also
lets us revert to inactive snapshots even for transient domains.
* src/qemu/qemu_driver.c (qemuDomainRevertToSnapshot): Support new
flags.
Commit 5e47785 broke reverts to offline system checkpoint snapshots
with older qemu, since there is no longer any code path to use
qemu -loadvm on next boot. Meanwhile, reverts to offline system
checkpoints have been broken for newer qemu, both before and
after that commit, since -loadvm no longer works to revert to
disk state without accompanying vm state. Fix both of these by
using qemu-img to revert disk state.
Meanwhile, consolidate the (now 3) clients of a qemu-img iteration
over all disks of a VM into one function, so that any future
algorithmic fixes to the FIXMEs in that function after partial
loop iterations are dealt with at once. That does mean that this
patch doesn't handle partial reverts very well, but we're not
making the situation any worse in this patch.
* src/qemu/qemu_driver.c (qemuDomainRevertToSnapshot): Use
qemu-img rather than 'qemu -loadvm' to revert to offline snapshot.
(qemuDomainSnapshotRevertInactive): New helper.
(qemuDomainSnapshotCreateInactive): Factor guts...
(qemuDomainSnapshotForEachQcow2): ...into new helper.
(qemuDomainSnapshotDiscard): Use it.
If you take a checkpoint snapshot of a running domain, then pause
qemu, then restore the snapshot, the result should be a running
domain, but the code was leaving things paused. Furthermore, if
you take a checkpoint of a paused domain, then run, then restore,
there was a brief but non-deterministic window of time where the
domain was running rather than paused. Fix both of these
discrepancies by always pausing before restoring.
Also, check that the VM is active every time lock is dropped
between two monitor calls.
Finally, straighten out the events that get emitted on each
transition.
* src/qemu/qemu_driver.c (qemuDomainRevertToSnapshot): Always
pause before reversion, and improve events.
Implement the new running/paused overrides for saved state management.
Unfortunately, for virDomainSaveImageDefineXML, the saved state
updates are write-only - I don't know of any way to expose a way
to query the current run/pause setting of an existing save image
file to the user without adding a new API or modifying the domain
xml of virDomainSaveImageGetXMLDesc to include a new element to
reflect the state bit encoded into the save image. However, I
don't think this is a show-stopper, since the API is designed to
leave the state bit alone unless an explicit flag is used to
change it.
* src/qemu/qemu_driver.c (qemuDomainSaveInternal)
(qemuDomainSaveImageOpen): Adjust signature.
(qemuDomainSaveFlags, qemuDomainManagedSave)
(qemuDomainRestoreFlags, qemuDomainSaveImageGetXMLDesc)
(qemuDomainSaveImageDefineXML, qemuDomainObjRestore): Adjust
callers.
There are two classes of management apps that track events - one
that only cares about on/off (and only needs to track EVENT_STARTED
and EVENT_STOPPED), and one that cares about paused/running (also
tracks EVENT_SUSPENDED/EVENT_RESUMED). To keep both classes happy,
any transition that can go from inactive to paused must emit two
back-to-back events - one for started and one for suspended (since
later resuming of the domain will only send RESUMED, but the first
class isn't tracking that).
This also fixes a bug where virDomainCreateWithFlags with the
VIR_DOMAIN_START_PAUSED flag failed to start paused when restoring
from a managed save image.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_EVENT_SUSPENDED_RESTORED)
(VIR_DOMAIN_EVENT_SUSPENDED_FROM_SNAPSHOT)
(VIR_DOMAIN_EVENT_RESUMED_FROM_SNAPSHOT): New sub-events.
* src/qemu/qemu_driver.c (qemuDomainRevertToSnapshot): Use them.
(qemuDomainSaveImageStartVM): Likewise, and add parameter.
(qemudDomainCreate, qemuDomainObjStart): Send suspended event when
starting paused.
(qemuDomainObjRestore): Add parameter.
(qemuDomainObjStart, qemuDomainRestoreFlags): Update callers.
* examples/domain-events/events-c/event-test.c
(eventDetailToString): Map new detail strings.
QEMU uses USB bus name "usb.0" when using the legacy -usb argument.
If we want to allow USB devices to specify their addresses with legacy
-usb, we should either in case of legacy bus name drop the 0 from the
address bus, or just drop the 0 from device id. This patch does the
later.
Another solution would be to permit addressing on non-legacy USB
controllers only.
So that devices can be attached to hubs. Example, to attach to first
port of a usb-hub on port 1.
<hub type='usb'>
<address type='usb' bus='0' port='1'/>
</hub>
<input type='mouse' type='usb'>
<address type='usb' bus='0' port='1.1'/>
</hub>
also add a test entry
Commit 6766ff10 introduced a corner case bug with snapshot creation:
if a snapshot is created, but then we hit OOM while trying to
create the return value of the function, then we have polluted the
internal directory with the snapshot metadata with no way to clean
it up from the running libvirtd.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Don't
write metadata file on OOM condition.
Newer QEMU introduced cache=directsync for -drive, this patchset
is to expose it in libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_DIRECTSYNC),
As even $prefix_CACHE_V2 is set, we can't known if directsync
is supported.
Several users have reported problems with 'virsh start' failing because
it was encountering a managed save situation where the managed save file
was incomplete. Be more robust to this by using two different magic
numbers, so that newer libvirt can gracefully handle an incomplete file
differently than a complete one, while older libvirt will at least fail
up front rather than trying to load only to have qemu fail at the end.
Managed save is a convenience - it exists to preserve as much state
as possible; if the state was not preserved, it is reasonable to just
log that fact, then proceed with a fresh boot. On the other hand,
user saves are under user control, so we must fail, but by making
the failure message distinct, the user can better decide how to handle
the situation of an incomplete save file.
* src/qemu/qemu_driver.c (QEMUD_SAVE_PARTIAL): New define.
(qemuDomainSaveInternal): Use it to mark incomplete images.
(qemuDomainSaveImageOpen, qemuDomainObjRestore): Add parameter
that controls what to do with partial images.
(qemuDomainRestoreFlags, qemuDomainSaveImageGetXMLDesc)
(qemuDomainSaveImageDefineXML, qemuDomainObjStart): Update callers.
Based on an initial idea by Osier Yang.
In a SELinux or root-squashing NFS environment, libvirt has to go
through some hoops to create a new file that qemu can then open()
by name. Snapshots are a case where we want to guarantee an empty
file that qemu can open; also, reopening a save file to convert it
from being marked partial to complete requires a reopen to avoid
O_DIRECT headaches. Refactor some existing code to make it easier
to reuse in later patches.
* src/qemu/qemu_migration.h (qemuMigrationToFile): Drop parameter.
* src/qemu/qemu_migration.c (qemuMigrationToFile): Let cgroup do
the stat, rather than asking caller to do it and pass info down.
* src/qemu/qemu_driver.c (qemuOpenFile): New function, pulled from...
(qemuDomainSaveInternal): ...here.
(doCoreDump, qemuDomainSaveImageOpen): Use it here as well.
After supporting multi function pci device, we only reserve function 1 on slot 1.
The user can use the other function on slot 1 in the xml config file. We should
detect this wrong usage.
The libvirt BlockPull API supports the use of an initial bandwidth limit but the
qemu block_stream API does not. To get the desired behavior we use the two APIs
strung together: first BlockPull, then BlockJobSetSpeed. We can do this at the
driver level to avoid duplicated code in each monitor path.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Due to an unfortunate precedent in qemu, the units for the bandwidth parameter
to block_job_set_speed are different between the text monitor and the qmp
monitor. While the qmp monitor uses bytes/s, the text monitor expects MB/s.
Correct the units for the text interface.
Signed-off-by: Adam Litke <agl@us.ibm.com>
It is not possible to change the label of a TCP socket once it
has been opened. When creating a TCP socket care must be taken
to ensure the socket creation label is set & then cleared.
Remove the bogus call to virSecurityManagerSetProcessFDLabel
from the lock driver guest setup code and instead make use of
virSecurityManagerSetSocketLabel
There is no reason to forbid pausing an autodestroy domain
(not to mention that 'virsh start --paused --autodestroy'
succeeds in creating a paused autodestroy domain).
Meanwhile, qemu was failing to enforce the API documentation that
autodestroy domains cannot be saved. And while the original
documentation only mentioned save/restore, snapshots are another
form of saving that are close enough in semantics as to make no
sense on one-shot domains.
* src/qemu/qemu_driver.c (qemudDomainSuspend): Drop bogus check.
(qemuDomainSaveInternal, qemuDomainSnapshotCreateXML): Forbid
saves of autodestroy domains.
* src/libvirt.c (virDomainCreateWithFlags, virDomainCreateXML):
Document snapshot interaction.
According to qemu-kvm/qerror.c all messages start with a capital
"Device ", but the current code only scans for the lower case "device ".
This results in "virDomainUpdateDeviceFlags()" to not detect locked
CD-ROMs and reporting success even in the case of a failure:
# virsh qemu-monitor-command "$VM" change\ drive-ide0-0-0\ \"/var/lib/libvirt/images/ucs_2.4-0-sec4-20110714145916-dvd-amd64.iso\"
Device 'drive-ide0-0-0' is locked
# virsh update-device "$VM" /dev/stdin <<<"<disk type='file' device='cdrom'><driver name='qemu' type='raw'/><source file='/var/lib/libvirt/images/ucs_2.4-0-sec4-20110714145916-dvd-amd64.iso'/><target dev='hda' bus='ide'/><readonly/><alias name='ide0-0-0'/><address type='drive' controller='0' bus='0' unit='0'/></disk>"
Device updated successfully
Signed-off-by: Philipp Hahn <hahn@univention.de>
There have been several instances of people having problems with
a broken managed save file, and not aware that they could use
'virsh managedsave-remove dom' to fix things. Making it possible
to do this as part of starting a domain makes the same functionality
easier to find, and one less API call.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_START_FORCE_BOOT): New
flag.
* src/libvirt.c (virDomainCreateWithFlags): Document it.
* src/qemu/qemu_driver.c (qemuDomainObjStart): Alter signature.
(qemuAutostartDomain, qemuDomainStartWithFlags): Update callers.
* tools/virsh.c (cmdStart): Expose it in virsh.
* tools/virsh.pod (start): Document it.
Commit 3261761 made it possible to use pipes instead of sockets
for outgoing tunneled migration; however, it caused a regression
because the pipe was never given a SELinux label.
* src/qemu/qemu_migration.c (doTunnelMigrate): Label outgoing pipe.
When a user migrates a domain by command as
libvirt saves vm's domain XML config in destination host after migration.
But it saves vm->def. Then, the saved XML contains some garbage.
<domain type='kvm' id='50'>
^^^^^^^^
...
<console type='pty' tty='/dev/pts/5'>
^^^^^^^^^^^^^^^^^
Avoid saving unnecessary things by saving persistent vm definition.
On success, the 'sendkey' command does not return any data, so
any data in the reply should be considered to be an error
message
* src/qemu/qemu_monitor_text.c: Treat non-"" reply data as an
error message for 'sendkey' command
The QEMU 'sendkey' command expects keys to be encoded in the same
way as the RFB extended keycode set. Specifically it wants extended
keys to have the high bit of the first byte set, while the Linux
XT KBD driver codeset uses the low bit of the second byte. To deal
with this we introduce a new keymap 'RFB' and use that in the QEMU
driver
* include/libvirt/libvirt.h.in: Add VIR_KEYCODE_SET_RFB
* src/qemu/qemu_driver.c: Use RFB keycode set instead of XT KBD
* src/util/virkeycode-mapgen.py: Auto-generate the RFB keycode
set from the XT KBD set
* src/util/virkeycode.c: Add RFB keycode entry to table. Add a
verify check on cardinality of the codeOffset table
The APIs are designed to label a socket in a way that the libvirt daemon
itself is able to access it (i.e., in SELinux the label is virtd_t based
as opposed to svirt_* we use for labeling resources that need to be
accessed by a vm). The new name reflects this.
Audit all changes to the qemu vm->current_snapshot, and make them
update the saved xml file for both the previous and the new
snapshot, so that there is always at most one snapshot with
<active>1</active> in the xml, and that snapshot is used as the
current snapshot even across libvirtd restarts.
This patch does not fix the case of virDomainSnapshotDelete(,CHILDREN)
where one of the children is the current snapshot; that will be later.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Alter member
type and name.
* src/conf/domain_conf.c (virDomainSnapshotDefParseString)
(virDomainSnapshotDefFormat): Update clients.
* docs/schemas/domainsnapshot.rng: Tighten rng.
* src/qemu/qemu_driver.c (qemuDomainSnapshotLoad): Reload current
snapshot.
(qemuDomainSnapshotCreateXML, qemuDomainRevertToSnapshot)
(qemuDomainSnapshotDiscard): Track current snapshot.
Changing the current vm, and writing that change to the file
system, all before a new qemu starts, is risky; it's hard to
roll back if starting the new qemu fails for some reason.
Instead of abusing vm->current_snapshot and making the command
line generator decide whether the current snapshot warrants
using -loadvm, it is better to just directly pass a snapshot all
the way through the call chain if it is to be loaded.
This frees up the last use of snapshot->def->active for qemu's
use, so the next patch can repurpose that field for tracking
which snapshot is current.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Don't use active
field of snapshot.
* src/qemu/qemu_process.c (qemuProcessStart): Add a parameter.
* src/qemu/qemu_process.h (qemuProcessStart): Update prototype.
* src/qemu/qemu_migration.c (qemuMigrationPrepareAny): Update
callers.
* src/qemu/qemu_driver.c (qemudDomainCreate)
(qemuDomainSaveImageStartVM, qemuDomainObjStart)
(qemuDomainRevertToSnapshot): Likewise.
(qemuDomainSnapshotSetCurrentActive)
(qemuDomainSnapshotSetCurrentInactive): Delete unused functions.
https://bugzilla.redhat.com/show_bug.cgi?id=727709
mentions that if qemu fails to create the snapshot (such as what
happens on Fedora 15 qemu, which has qmp but where savevm is only
in hmp, and where libvirt is old enough to not try the hmp fallback),
then 'virsh snapshot-list dom' will show a garbage snapshot entry,
and the libvirt internal directory for storing snapshot metadata
will have a bogus file.
This fixes the fallout bug of polluting the snapshot-list with
garbage on failure (the root cause of the F15 bug of not having
fallback to hmp has already been fixed in newer libvirt releases).
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML): Allocate
memory before making snapshot, and cleanup on failure. Don't
dereference NULL if transient domain exited during snapshot creation.
* src/qemu/qemu_migration.c: avoid dead 'ret' assignment and silence
clang warning.
Detected by ccc-analyzer:
CC libvirt_driver_qemu_la-qemu_migration.lo
qemu/qemu_migration.c:2046:5: warning: Value stored to 'ret' is never read
ret = qemuMigrationConfirm(driver, sconn, vm,
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
pciDeviceListSteal(pcidevs, dev) removes dev from pcidevs reducing
the length of pcidevs, so moving onto what was the next dev is wrong.
Instead callers should pop entry 0 repeatedly until pcidevs is empty.
Signed-off-by: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
* src/qemu/qemu_monitor_json.c: Handle error "CommandNotFound" and
report the error.
* src/qemu/qemu_monitor_text.c: If a sub info command is not found,
it prints the output of "help info", for other commands,
"unknown command" is printed.
Without this patch, libvirt always report:
An error occurred, but the cause is unknown
This patch was adapted from a patch by Osier Yang <jyang@redhat.com> to
break out detection of unrecognized text monitor commands into a separate
function.
Signed-off-by: Adam Litke <agl@us.ibm.com>
* src/qemu/qemu_monitor_text.c: BALLOON_PREFIX was defined as
"balloon: actual=", which cause "actual=" is stripped early before
the real parsing. This patch changes BALLOON_PREFIX into "balloon: ",
and modifies related functions, also renames
"qemuMonitorParseExtraBalloonInfo" to "qemuMonitorParseBalloonInfo",
as after the changing, it parses all the info returned by "info balloon".
A virsh command like:
migrate --live --copy-storage-all Guest qemu+ssh://user@host/system
--persistent --verbose
shows
Migration: [ 0 %]
during the storage copy and does not start counting
until the ram transfer starts
Fix this by scraping optional disk transfer status, and adding it
into the progress meter.
Otherwise the device will still be bound to pci-stub driver even
it's set as "managed=yes" when do detaching. Of course, it won't
triger any driver reprobing too.
In some versions of qemu, both virtio-blk-pci and virtio-net-pci
devices can have an event_idx setting that determines some details of
event processing. When it is enabled, it "reduces the number of
interrupts and exits for the guest". qemu will automatically enable
this feature when it is available, but there may be cases where this
new feature could actually make performance worse (NB: no such case
has been found so far).
As a safety switch in case such a situation is encountered in the
field, this patch adds a new attribute "event_idx" to the <driver>
element of both disk and interface devices. event_idx can be set to
"on" (to force event_idx on in case qemu has it disabled by default)
or "off" (for force event_idx off). In the case that event_idx support
isn't present in qemu, the attribute is ignored (this on the advice of
the qemu developer).
docs/formatdomain.html.in: document the new flag (marking it as
"don't mess with this!"
docs/schemas/domain.rng: add event_idx in appropriate places
src/conf/domain_conf.[ch]: add event_idx to parser and formatter
src/libvirt_private.syms: export
virDomainVirtioEventIdx(From|To)String
src/qemu/qemu_capabilities.[ch]: detect and report event_idx in
disk/net
src/qemu/qemu_command.c: add event_idx parameter to qemu commandline
when appropriate.
tests/qemuxml2argvdata/qemuxml2argv-event_idx.args,
tests/qemuxml2argvdata/qemuxml2argv-event_idx.xml,
tests/qemuxml2argvtest.c,
tests/qemuxml2xmltest.c: test cases for event_idx.
By opening a connection to remote qemu process ourselves and passing the
socket to qemu we get much better errors than just "migration failed"
when the connection is opened by qemu.
The core of these two functions is very similar and most of it is even
exactly the same. Factor out the core functionality into a separate
function to remove code duplication and make further changes easier.
The functions for manipulating pidfiles are in util/util.{c,h}.
We will shortly be adding some further pidfile related functions.
To avoid further growing util.c, this moves the pidfile related
functions into a dedicated virpidfile.{c,h}. The functions are
also all renamed to have 'virPidFile' as their name prefix
* util/util.h, util/util.c: Remove all pidfile code
* util/virpidfile.c, util/virpidfile.h: Add new APIs for pidfile
handling.
* lxc/lxc_controller.c, lxc/lxc_driver.c, network/bridge_driver.c,
qemu/qemu_process.c: Add virpidfile.h include and adapt for API
renames
Our logic throws off analyzer tools:
ptr var = NULL;
if (flags == 0) flags = live ? _LIVE : _CONFIG;
if (flags & _LIVE) do stuff
if (flags & _CONFIG) var = non-null;
if (flags & _LIVE) do more stuff
else if (flags & _CONFIG) use var
the tools keep thinking that var can still be NULL in the last
if clause, adding the hint shuts them up.
* src/qemu/qemu_driver.c (qemuDomainSetBlkioParameters): Add a
static analysis hint.
The following XML:
<serial type='udp'>
<source mode='connect' service='9999'/>
</serial>
is accepted by domain_conf.c but maps to the qemu command line:
-chardev udp,host=127.0.0.1,port=2222,localaddr=(null),localport=(null)
qemu can cope with everything omitting except the connection port, which
seems to also be the intent of domain_conf validation, so let's not
generate bogus command lines for that case.
The defaults are empty strings for addresses and 0 for the localport
Additionally, tweak the qemu cli parsing to handle omitted host
parameters
for -serial udp
Transient domains reject attempts to set autostart, and using
virDomainCreate to restart a domain only works on persistent
domains. Therefore, managed save makes no sense on transient
domains, and should be rejected up front rather than creating
an otherwise unrecoverable managed save file.
Besides, transient domains imply that a lot more management is
being done by the upper layer; this includes the assumption
that the upper layer is okay managing the saved state file
created by virDomainSave, and does not need to use managed save.
* src/libvirt.c: Document that transient domains are incompatible
with managed save.
* src/qemu/qemu_driver.c (qemuDomainManagedSave): Enforce it.
* src/libxl/libxl_driver.c (libxlDomainManagedSave): Likewise.
I noticed some inconsistent use of 'else'.
* src/qemu/qemu_driver.c (qemuCPUCompare)
(qemuDomainSnapshotCreateXML, qemuDomainRevertToSnapshot)
(qemuDomainSnapshotDiscard): Match coding conventions.
If a snapshot with the name already exists, virDomainSnapshotAssignDef()
just returns NULL, in which case the snapshot definition is leaked.
Currently this leak is not a big problem, since qemuDomainSnapshotLoad()
is only called once during initial startup of libvirtd.
Signed-off-by: Philipp Hahn <hahn@univention.de>
Detected by ccc-analyzer, reported by Alex Jia.
qemuProcessStart always calls qemuProcessWaitForMonitor with a
non-negative position, but qemuProcessAttach always calls with -1.
In the latter case, there is no log file we can scrape, so we
also should not be trying to scrape the logs if the qemu process
died at the very end.
* src/qemu/qemu_process.c (qemuProcessWaitForMonitor): Don't try
to read from log in qemuProcessAttach case.
Value stored to 'ret' is never read, so remove this dead assignment.
* src/qemu/qemu_monitor_text.c: kill dead assignment.
Signed-off-by: Alex Jia <ajia@redhat.com>
Value stored to 'ret' is never read, in fact, 'cleanup' section will
directly return -1 when function is fail, so remove this dead assignment.
* src/qemu/qemu_process.c: kill dead assignment.
Signed-off-by: Alex Jia <ajia@redhat.com>
Quite a few leaks detected by coverity. For chr, the leaks were
close enough to the allocations to plug in place; for disk, the
leaks were separated from the allocation by enough other lines with
intermediate failure cases that I refactored the cleanup instead.
* src/qemu/qemu_command.c (qemuParseCommandLine): Plug leaks.
Warning detected by Coverity. No need for the NULL check, and
removing it silences the warning without any semantic change.
* src/qemu/qemu_migration.c (qemuMigrationFinish): All entries to
endjob had non-NULL vm.
Coverity detected that 5 of 6 callers of virJSONValueArrayGet checked
for a NULL return; and that by not checking we risk a null deref
during an error. The error is unlikely since the prior call to
virJSONValueArraySize would probably have already caught any botched
JSON array parse, but better safe than sorry.
* src/qemu/qemu_monitor_json.c (qemuMonitorJSONGetBlockJobInfo):
Check for NULL.
(qemuMonitorJSONExtractPtyPaths): Fix typo.
Revert 6a1f5f568f. Now that libvirt_iohelper takes fds by
inheritance rather than by open() (commit 1eb66479), there is
no longer a race where the parent can unlink() a file prior to
the iohelper open()ing the same file. From there, it makes
more sense to have the callers both create and unlink, rather
than the caller create and the stream unlink, since the latter
was only needed when iohelper had to do the unlink.
* src/fdstream.h (virFDStreamOpenFile, virFDStreamCreateFile):
Callers are responsible for deletion.
* src/fdstream.c (virFDStreamOpenFileInternal): Don't leak created
file on failure.
(virFDStreamOpenFile, virFDStreamCreateFile): Drop parameter.
* src/lxc/lxc_driver.c (lxcDomainOpenConsole): Update callers.
* src/qemu/qemu_driver.c (qemuDomainScreenshot)
(qemuDomainOpenConsole): Likewise.
* src/storage/storage_driver.c (storageVolumeDownload)
(storageVolumeUpload): Likewise.
* src/uml/uml_driver.c (umlDomainOpenConsole): Likewise.
* src/vbox/vbox_tmpl.c (vboxDomainScreenshot): Likewise.
* src/xen/xen_driver.c (xenUnifiedDomainOpenConsole): Likewise.
The previous qemu patch could end up calling unlink(tmp) before
tmp was the name of a valid file (unlinking a fileXXXXXX template
instead), or calling unlink(tmp) twice on success (once here,
and once at the end of the stream). Meanwhile, vbox also suffered
from the same leaked tmp file bug.
* src/qemu/qemu_driver.c (qemuDomainScreenshot): Don't unlink on
success, or on invalid name.
* src/vbox/vbox_tmpl.c (vboxDomainScreenshot): Don't leak temp file.
Currently, we attempt to run sync job and async job at the same time. It
means that the monitor commands for two jobs can be run in any order.
In the function qemuDomainObjEnterMonitorInternal():
if (priv->job.active == QEMU_JOB_NONE && priv->job.asyncJob) {
if (qemuDomainObjBeginNestedJob(driver, obj) < 0)
We check whether the caller is an async job by priv->job.active and
priv->job.asynJob. But when an async job is running, and a sync job is
also running at the time of the check, then priv->job.active is not
QEMU_JOB_NONE. So we cannot check whether the caller is an async job
in the function qemuDomainObjEnterMonitorInternal(), and must instead
put the burden on the caller to tell us when an async command wants
to do a nested job.
Once the burden is on the caller, then only async monitor enters need
to worry about whether the VM is still running; for sync monitor enter,
the internal return is always 0, so lots of ignore_value can be dropped.
* src/qemu/THREADS.txt: Reflect new rules.
* src/qemu/qemu_domain.h (qemuDomainObjEnterMonitorAsync): New
prototype.
* src/qemu/qemu_process.h (qemuProcessStartCPUs)
(qemuProcessStopCPUs): Add parameter.
* src/qemu/qemu_migration.h (qemuMigrationToFile): Likewise.
(qemuMigrationWaitForCompletion): Make static.
* src/qemu/qemu_domain.c (qemuDomainObjEnterMonitorInternal): Add
parameter.
(qemuDomainObjEnterMonitorAsync): New function.
(qemuDomainObjEnterMonitor, qemuDomainObjEnterMonitorWithDriver):
Update callers.
* src/qemu/qemu_driver.c (qemuDomainSaveInternal)
(qemudDomainCoreDump, doCoreDump, processWatchdogEvent)
(qemudDomainSuspend, qemudDomainResume, qemuDomainSaveImageStartVM)
(qemuDomainSnapshotCreateActive, qemuDomainRevertToSnapshot):
Likewise.
* src/qemu/qemu_process.c (qemuProcessStopCPUs)
(qemuProcessFakeReboot, qemuProcessRecoverMigration)
(qemuProcessRecoverJob, qemuProcessStart): Likewise.
* src/qemu/qemu_migration.c (qemuMigrationToFile)
(qemuMigrationWaitForCompletion, qemuMigrationUpdateJobStatus)
(qemuMigrationJobStart, qemuDomainMigrateGraphicsRelocate)
(doNativeMigrate, doTunnelMigrate, qemuMigrationPerformJob)
(qemuMigrationPerformPhase, qemuMigrationFinish)
(qemuMigrationConfirm): Likewise.
* src/qemu/qemu_hotplug.c: Drop unneeded ignore_value.
whether or not previous return value is -1, the following codes will be
executed for a inactive guest in src/qemu/qemu_driver.c:
ret = virDomainSaveConfig(driver->configDir, persistentDef);
and if everything is okay, 'ret' is assigned to 0, the previous 'ret'
will be overwritten, this patch will fix this issue.
* src/qemu/qemu_driver.c: avoid return value is overwritten when give a argument
in out of blkio weight range for a inactive guest.
* how to reproduce?
% virsh blkiotune ${guestname} --weight 10
% echo $?
Note: guest must be inactive, argument 10 in out of blkio weight range,
and can get a error information by checking libvirtd.log, however,
virsh hasn't raised any error information, and return value is 0.
https://bugzilla.redhat.com/show_bug.cgi?id=726304
Signed-off-by: Alex Jia <ajia@redhat.com>
whether or not previous return value is -1, the following codes will be
executed for a inactive guest in qemuDomainSetMemoryParameters:
ret = virDomainSaveConfig(driver->configDir, persistentDef);
and if everything is okay, 'ret' is assigned to 0, the previous 'ret'
will be overwritten, this patch will fix this issue.
* src/qemu/qemu_driver.c: avoid return value is overwritten when set
min_guarante value to a inactive guest.
* how to reproduce?
% virsh memtune ${guestname} --min_guarante 1024
% echo $?
Note: guest must be inactive, in fact, 'min_guarante' hasn't been implemented
in memory tunable, and I can get the error when check actual libvirtd.log,
however, virsh hasn't raised any error information, and return value is 0.
Signed-off-by: Alex Jia <ajia@redhat.com>
Introduced by f9a837da73, the condition is not changed after
the else clause is removed. So now it quit with "domain is not
running" when the domain is running. However, when the domain is
not running, it reports "no job is active".
How to reproduce:
1)
% virsh start $domain
% virsh domjobabort $domain
error: Requested operation is not valid: domain is not running
2)
% virsh destroy $domain
% virsh domjobabort $domain
error: Requested operation is not valid: no job is active on the domain
3)
% virsh save $domain /tmp/$domain.save
Before above commands finished, try to abort job in another terminal
% virsh domabortjob $domain
error: Requested operation is not valid: domain is not running
Using a macro ensures that all the code is looking for the same
prefix.
* src/conf/domain_conf.h (VIR_NET_GENERATED_PREFIX): New macro.
* src/conf/domain_conf.c (virDomainNetDefParseXML): Use it.
* src/uml/uml_conf.c (umlConnectTapDevice): Likewise.
* src/qemu/qemu_command.c (qemuNetworkIfaceConnect): Likewise.
Suggested by Laine Stump.
The goal here is that save-image-dumpxml fed back to
save-image-define should not change the save file; anywhere that
this is not the case is probably a bug in domain_conf.c.
* src/qemu/qemu_driver.c (qemuDomainSaveImageGetXMLDesc)
(qemuDomainSaveImageDefineXML): New functions.
(qemuDomainSaveImageOpen): Add parameter.
(qemuDomainRestoreFlags, qemuDomainObjRestore): Adjust clients.
With this, it is possible to update the path to a disk backing
image on either the save or restore action, without having to
binary edit the XML embedded in the state file.
This also modifies virDomainSave to output a smaller xml (only
the inactive xml, which is all the more virDomainRestore parses),
while still guaranteeing padding for most typical abi-compatible
xml replacements, necessary so that the next patch for
virDomainSaveImageDefineXML will not cause unnecessary
modifications to the save image file.
* src/qemu/qemu_driver.c (qemuDomainSaveInternal): Add parameter,
only use inactive state, and guarantee padding.
(qemuDomainSaveImageOpen): Add parameter.
(qemuDomainSaveFlags, qemuDomainManagedSave)
(qemuDomainRestoreFlags, qemuDomainObjRestore): Update callers.
The domain XML now understands the <listen> subelement of its
<graphics> element (including when listen type='network'), and the
network driver has an internal API that will turn a network name into
an IP address, so the final logical step is to put the glue into the
qemu driver so that when it is starting up a domain, if it finds
<listen type='network' network='xyz'/> in the XML, it will call the
network driver to get an IPv4 address associated with network xyz, and
tell qemu to listen for vnc (or spice) on that address rather than the
default address (localhost).
The motivation for this is that a large installation may want the
guests' VNC servers listening on physical interfaces rather than
localhost, so that users can connect directly from the outside; this
requires sending qemu the appropriate IP address to listen on. But
this address will of course be different for each host, and if a guest
might be migrated around from one host to another, it's important that
the guest's config not have any information embedded in it that is
specific to one particular host. <listen type='network.../> can solve
this problem in the following manner:
1) on each host, define a libvirt network of the same name,
associated with the interface on that host that should be used
for listening (for example, a simple macvtap network: <forward
mode='bridge' dev='eth0'/>, or host bridge network: <forward
mode='bridge'/> <bridge name='br0'/>
2) in the <graphics> element of each guest's domain xml, tell vnc to
listen on the network name used in step 1:
<graphics type='vnc' port='5922'>
<listen type='network'network='example-net'/>
</graphics>
(all the above also applies for graphics type='spice').
Once it's plugged in, the <listen> element will be an optional
replacement for the "listen" attribute that graphics elements already
have. If the <listen> element is type='address', it will have an
attribute called 'address' which will contain an IP address or dns
name that the guest's display server should listen on. If, however,
type='network', the <listen> element should have an attribute called
'network' that will be set to the name of a network configuration to
get the IP address from.
* docs/schemas/domain.rng: updated to allow the <listen> element
* docs/formatdomain.html.in: document the <listen> element and its
attributes.
* src/conf/domain_conf.[hc]:
1) The domain parser, formatter, and data structure are modified to
support 0 or more <listen> subelements to each <graphics>
element. The old style "legacy" listen attribute is also still
accepted, and will be stored internally just as if it were a
separate <listen> element. On output (i.e. format), the address
attribute of the first <listen> element of type 'address' will be
duplicated in the legacy "listen" attribute of the <graphic>
element.
2) The "listenAddr" attribute has been removed from the unions in
virDomainGRaphicsDef for graphics types vnc, rdp, and spice.
This attribute is now in the <listen> subelement (aka
virDomainGraphicsListenDef)
3) Helper functions were written to provide simple access
(both Get and Set) to the listen elements and their attributes.
* src/libvirt_private.syms: export the listen helper functions
* src/qemu/qemu_command.c, src/qemu/qemu_hotplug.c,
src/qemu/qemu_migration.c, src/vbox/vbox_tmpl.c,
src/vmx/vmx.c, src/xenxs/xen_sxpr.c, src/xenxs/xen_xm.c
Modify all these files to use the listen helper functions rather
than directly referencing the (now missing) listenAddr
attribute. There can be multiple <listen> elements to a single
<graphics>, but the drivers all currently only support one, so all
replacements of direct access with a helper function indicate index
"0".
* tests/* - only 3 of these are new files added explicitly to test the
new <listen> element. All the others have been modified to reflect
the fact that any legacy "listen" attributes passed in to the domain
parse will be saved in a <listen> element (i.e. one of the
virDomainGraphicsListenDefs), and during the domain format function,
both the <listen> element as well as the legacy attributes will be
output.
qemuMigrationUpdateJobStatus (called in a loop by migration
and save tasks) uses qemuDomainObjEnterMonitorWithDriver;
however, that function ended up starting a nested job without
releasing the driver.
Since no one else is making nested calls, we can inline the
internal functions to properly track driver_locked.
* src/qemu/qemu_domain.h (qemuDomainObjBeginNestedJob)
(qemuDomainObjBeginNestedJobWithDriver)
(qemuDomainObjEndNestedJob): Drop unused prototypes.
* src/qemu/qemu_domain.c (qemuDomainObjEnterMonitorInternal):
Reflect driver lock to nested job.
(qemuDomainObjBeginNestedJob)
(qemuDomainObjBeginNestedJobWithDriver)
(qemuDomainObjEndNestedJob): Drop unused functions.
As written in virStorageFileGetMetadataFromFD decription, caller
must free metadata after use. Qemu driver miss this and therefore
leak metadata which can grow to huge mem leak if somebody query
for blockInfo a lot.
The error in getCompressionType will never be reported, change
the errors codes into warning (VIR_WARN("%s", _(foo)); doesn't break
syntax-check rule), and also improve the docs in qemu.conf to tell
user the truth.
Make MIGRATION_OUT use the new helper methods.
This also introduces new protection to migration v3 process: the
migration job is held from Begin to Confirm to avoid changes to a domain
during migration (esp. between Begin and Perform phases). This change is
automatically applied to p2p and tunneled migrations. For normal
migration, this requires support from a client. In other words, if an
old (pre 0.9.4) client starts normal migration of a domain, the domain
will not be protected against changes between Begin and Perform steps.
Without this, a configure built by autoconf 2.59 was broken when
trying to detect which compiler warning flags were supported.
* .gnulib: Update to latest, for warnings.m4 fix.
* bootstrap.conf: Add fclose explicitly, to match recent gnulib
implicit dependency changes.
* src/qemu/qemu_conf.c (includes): Drop unused include.
* src/uml/uml_conf.c (include): Likewise.
Reported by Daniel P. Berrange.
Every DomainNetDef has a bandwidth, as does every portgroup.
Whenever a DomainNetDef of type NETWORK is about to be used, a call is
made to networkAllocateActualDevice(). This function chooses the "best"
bandwidth object and places it in the DomainActualNetDef.
From that point on, whenever some code needs to use the bandwidth data
for the interface, it's retrieved with virDomainNetGetActualBandwidth(),
which will always return the "best" info as determined in the
previous step.
The cpu bandwidth is applied at the vcpu group level. We should apply it
at the vm group level too, because the vm may do heavy I/O, and it will affect
the other vm.
We apply cpu bandwidth at the vcpu and the vm group level, so we must ensure
that max(child_quota) <= parent_quota when we modify cpu bandwidth.
Now that virDomainSetVcpusFlags knows about VIR_DOMAIN_AFFECT_CURRENT,
so should virDomainGetVcpusFlags.
Unfortunately, the virsh counterpart 'virsh vcpucount' has already
commandeered --current for a different meaning, so teaching virsh
to expose this in the next patch will require a bit of care.
* src/libvirt.c (virDomainGetVcpusFlags): Allow
VIR_DOMAIN_AFFECT_CURRENT.
* src/libxl/libxl_driver.c (libxlDomainGetVcpusFlags): Likewise.
* src/qemu/qemu_driver.c (qemudDomainGetVcpusFlags): Likewise.
* src/test/test_driver.c (testDomainGetVcpusFlags): Likewise.
* src/xen/xen_driver.c (xenUnifiedDomainGetVcpusFlags): Likewise.
Although most functions in libvirt return 0 on success and < 0 on
failure, there are a few functions lingering around that return errno
(a positive value) on failure, and sometimes code calling those
functions incorrectly assumes the <0 standard. I noticed one of these
the other day when auditing networkStartDhcpDaemon after Guido Gunther
found a place where success was improperly returned on failure (that
patch has been acked and is pending a push). The problem was that it
expected the return value from virFileReadPid to be < 0 on failure,
but it was actually positive (it was also neglected to set the return
code in this case, similar to the bug found by Guido).
This all led to the fact that *all* of the virFile*Pid functions in
util.c are returning errno on failure. This patch remedies that
problem by changing them all to return -errno on failure, and makes
any necessary changes to callers of the functions. (In the meantime, I
also properly set the return code on failure of virFileReadPid in
networkStartDhcpDaemon).
In the XML file we now have
<cputune>
<shares>1024</shares>
<period>90000</period>
<quota>0</quota>
</cputune>
But the schedinfo parameter are being named
cpu_shares: 1024
cfs_period: 90000
cfs_quota: 0
The period/quota is per-vcpu value, so these new tunables should be named
'vcpu_period' and 'vcpu_quota'.
When an operation started by virDomainBlockPull completes (either with
success or with failure), raise an event to indicate the final status.
This API allow users to avoid polling on virDomainGetBlockJobInfo if
they would prefer to use an event mechanism.
* daemon/remote.c: Dispatch events to client
* include/libvirt/libvirt.h.in: Define event ID and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Extend API to handle the new event
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
for block_stream completion and emit a libvirt block pull event
* src/remote/remote_driver.c: Receive and dispatch events to application
* src/remote/remote_protocol.x: Wire protocol definition for the event
* src/remote_protocol-structs: structure definitions for protocol verification
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c: Watch for BLOCK_STREAM_COMPLETED event
from QEMU monitor
The virDomainBlockPull* family of commands are enabled by the
following HMP/QMP commands: 'block_stream', 'block_job_cancel',
'info block-jobs' / 'query-block-jobs', and 'block_job_set_speed'.
* src/qemu/qemu_driver.c src/qemu/qemu_monitor_text.[ch]: implement disk
streaming by using the proper qemu monitor commands.
* src/qemu/qemu_monitor_json.[ch]: implement commands using the qmp monitor
When auto-dumping a domain on crash events, or autostarting a domain
with managed save state, let the user configure whether to imply
the bypass cache flag.
* src/qemu/qemu.conf (auto_dump_bypass_cache, auto_start_bypass_cache):
Document new variables.
* src/qemu/libvirtd_qemu.aug (vnc_entry): Let augeas parse them.
* src/qemu/qemu_conf.h (qemud_driver): Store new preferences.
* src/qemu/qemu_conf.c (qemudLoadDriverConfig): Parse them.
* src/qemu/qemu_driver.c (processWatchdogEvent, qemuAutostartDomain):
Honor them.
Wire together the previous patches to support file system cache
bypass during API save/restore requests in qemu.
* src/qemu/qemu_driver.c (qemuDomainSaveInternal, doCoreDump)
(qemudDomainObjStart, qemuDomainSaveImageOpen, qemuDomainObjRestore)
(qemuDomainObjStart): Add parameter.
(qemuDomainSaveFlags, qemuDomainManagedSave, qemudDomainCoreDump)
(processWatchdogEvent, qemudDomainStartWithFlags, qemuAutostartDomain)
(qemuDomainRestoreFlags): Update callers.
For all hypervisors that support save and restore, the new API
now performs the same functions as the old.
VBox is excluded from this list, because its existing domainsave
is broken (there is no corresponding domainrestore, and there
is no control over the filename used in the save). A later
patch should change vbox to use its implementation for
managedsave, and teach start to use managedsave results.
* src/libxl/libxl_driver.c (libxlDomainSave): Move guts...
(libxlDomainSaveFlags): ...to new function.
(libxlDomainRestore): Move guts...
(libxlDomainRestoreFlags): ...to new function.
* src/test/test_driver.c (testDomainSave, testDomainSaveFlags)
(testDomainRestore, testDomainRestoreFlags): Likewise.
* src/xen/xen_driver.c (xenUnifiedDomainSave)
(xenUnifiedDomainSaveFlags, xenUnifiedDomainRestore)
(xenUnifiedDomainRestoreFlags): Likewise.
* src/qemu/qemu_driver.c (qemudDomainSave, qemudDomainRestore):
Rename and move guts.
(qemuDomainSave, qemuDomainSaveFlags, qemuDomainRestore)
(qemuDomainRestoreFlags): ...here.
(qemudDomainSaveFlag): Rename...
(qemuDomainSaveInternal): ...to this, and update callers.
The network driver needs to assign physical devices for use by modes
that use macvtap, keeping track of which physical devices are in use
(and how many instances, when the devices can be shared). Three calls
are added:
networkAllocateActualDevice - finds a physical device for use by the
domain, and sets up the virDomainActualNetDef accordingly.
networkNotifyActualDevice - assumes that the domain was already
running, but libvirtd was restarted, and needs to be notified by each
already-running domain about what interfaces they are using.
networkReleaseActualDevice - decrements the usage count of the
allocated physical device, and frees the virDomainActualNetDef to
avoid later accidentally using the device.
bridge_driver.[hc] - the new APIs. When WITH_NETWORK is false, these
functions are all #defined to be "0" in the .h file (effectively
becoming a NOP) to prevent link errors.
qemu_(command|driver|hotplug|process).c - add calls to the above APIs
in the appropriate places.
tests/Makefile.am - we need to include libvirt_driver_network.la
whenever libvirt_driver_qemu.la is linked, to avoid unreferenced
symbols (in functions that are never called by the test
programs...)
This is the one function outside of domain_conf.c that plays around
with (even modifying) the internals of the virDomainNetDef, and thus
can't be fixed up simply by replacing direct accesses to the fields of
the struct with the GetActual*() access functions.
In this case, we need to check if the defined type is "network", and
if it is *then* check the actual type; if the actual type is "bridge",
then we can at least put the bridgename in a place where it can be
used; otherwise (if type isn't "bridge"), we behave exactly as we used
to - just null out *everything*.
The qemu driver accesses fields in the virDomainNetDef directly, but
with the advent of the virDomainActualNetDef, some pieces of
information may be found in a different place (the ActualNetDef) if
the network connection is of type='network' and that network is of
forward type='bridge|private|vepa|passthrough'. The previous patch
added functions to mask this difference from callers - they hide the
decision making process and just pick the value from the proper place.
This patch uses those functions in the qemu driver as a first step in
making qemu work with the new network types. At this point, the
virDomainActualNetDef is guaranteed always NULL, so the GetActualX()
function will return exactly what the def->X that's being replaced
would have returned (ie bisecting is not compromised).
There is one place (in qemu_driver.c) where the internal details of
the NetDef are directly manipulated by the code, so the GetActual
functions cannot be used there without extra additional code; that
file will be treated in a separate patch.
The virtPortProfile in the domain interface struct is now a separately
allocated object *pointed to by* (rather than contained in) the main
virDomainNetDef object. This is done to make it easier to figure out
when a virtualPortProfile has/hasn't been specified in a particular
config.
Otherwise, an ABI mismatch gives error messages attributing the target
xml string as current, and the current domain state as the new xml.
* src/qemu/qemu_migration.c (qemuMigrationBegin): Use correct
argument order.
Since libvirt is multi-threaded, we should use FD_CLOEXEC as much
as possible in the parent, and only relax fds to inherited after
forking, to avoid leaking an fd created in one thread to a fork
run in another thread. This gets us closer to that ideal, by
making virCommand automatically clear FD_CLOEXEC on fds intended
for the child, as well as avoiding a window of time with non-cloexec
pipes created for capturing output.
* src/util/command.c (virExecWithHook): Use CLOEXEC in parent. In
child, guarantee that all fds to pass to child are inheritable.
(getDevNull): Use CLOEXEC.
(prepareStdFd): New helper function.
(virCommandRun, virCommandRequireHandshake): Use pipe2.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Simplify caller.
This patch implements cfs_period and cfs_quota's modification.
We can use the command 'virsh schedinfo' to query or modify cfs_period and
cfs_quota.
If you query period or quota from config file, the value 0 means it does not set
in the config file.
If you set period or quota to config file, the value 0 means that delete current
setting from config file.
If you modify period or quota while vm is running, the value 0 means that use
current value.
Starting/ending jobs when closing the connection may reset any
error which was reported earlier in p2p migration. We must
save the original error before doing so. This means we can also
just call virConnectClose as normal, instead of virUnrefConnect
* src/qemu/qemu_migration.c: Preserve errors in p2p migration
There were two API in driver.c that were silently masking flags
bits prior to calling out to the drivers, and several others
that were explicitly masking flags bits. This is not
forward-compatible - if we ever have that many flags in the
future, then talking to an old server that masks out the
flags would be indistinguishable from talking to a new server
that can honor the flag. In general, libvirt.c should forward
_all_ flags on to drivers, and only the drivers should reject
unknown flags.
In the case of virDrvSecretGetValue, the solution is to separate
the internal driver callback function to have two parameters
instead of one, with only one parameter affected by the public
API. In the case of virDomainGetXMLDesc, it turns out that
no one was ever mixing VIR_DOMAIN_XML_INTERNAL_STATUS with
the dumpxml path in the first place; that internal flag was
only used in saving and restoring state files, which happened
to be in functions internal to a single file, so there is no
mixing of the internal flag with a public flags argument.
Additionally, virDomainMemoryStats passed a flags argument
over RPC, but not to the driver.
* src/driver.h (VIR_DOMAIN_XML_FLAGS_MASK)
(VIR_SECRET_GET_VALUE_FLAGS_MASK): Delete.
(virDrvSecretGetValue): Separate out internal flags.
(virDrvDomainMemoryStats): Provide missing flags argument.
* src/driver.c (verify): Drop unused check.
* src/conf/domain_conf.h (virDomainObjParseFile): Delete
declaration.
(virDomainXMLInternalFlags): Move...
* src/conf/domain_conf.c: ...here. Delete redundant include.
(virDomainObjParseFile): Make static.
* src/libvirt.c (virDomainGetXMLDesc, virSecretGetValue): Update
clients.
(virDomainMemoryPeek, virInterfaceGetXMLDesc)
(virDomainMemoryStats, virDomainBlockPeek, virNetworkGetXMLDesc)
(virStoragePoolGetXMLDesc, virStorageVolGetXMLDesc)
(virNodeNumOfDevices, virNodeListDevices, virNWFilterGetXMLDesc):
Don't mask unknown flags.
* src/interface/netcf_driver.c (interfaceGetXMLDesc): Reject
unknown flags.
* src/secret/secret_driver.c (secretGetValue): Update clients.
* src/remote/remote_driver.c (remoteSecretGetValue)
(remoteDomainMemoryStats): Likewise.
* src/qemu/qemu_process.c (qemuProcessGetVolumeQcowPassphrase):
Likewise.
* src/qemu/qemu_driver.c (qemudDomainMemoryStats): Likewise.
* daemon/remote.c (remoteDispatchDomainMemoryStats): Likewise.
The regression is introduced by Commit da1eba6b, the new
codes with this commit doesn't reset "ret" to "-1" when
it fails on parsing the device XML (live device attachment)
This patch changes the codes to reset the "ret" and "-1",
and also changes the codes so that it don't modify "ret"
for condition checking.
How to reproduce:
% cat test.xml
<disk type='oops' device='disk'>
<driver name='qemu' type='raw'/>
<source file='/var/lib/libvirt/images/test.img'/>
<target dev='vda' bus='virtio'/>
</disk>
% virsh attach-device $domain test.xml
Device attached successfully
The device attachment failed actually with error "unknown disk type 'oops'",
however, it reports success.
Commit f548480b broke migration v3 on qemu, because the driver
passed flags on through to qemu_migration even though
qemu_migration wasn't using those flags.
* src/qemu/qemu_migration.h (QEMU_MIGRATION_FLAGS): New define.
* src/qemu/qemu_driver.c: Simplify all migration callbacks.
* src/qemu/qemu_migration.c (qemuMigrationConfirm): Fix regression.
The previous patches only cleaned up ATTRIBUTE_UNUSED flags cases;
auditing the drivers found other places where flags was being used
but not validated. In particular, domainGetXMLDesc had issues with
clients accepting a different set of flags than the common
virDomainDefFormat helper function.
* src/conf/domain_conf.c (virDomainDefFormat): Add common flag check.
* src/uml/uml_driver.c (umlDomainAttachDeviceFlags)
(umlDomainDetachDeviceFlags): Reject unknown
flags.
* src/vbox/vbox_tmpl.c (vboxDomainGetXMLDesc)
(vboxDomainAttachDeviceFlags)
(vboxDomainDetachDeviceFlags): Likewise.
* src/qemu/qemu_driver.c (qemudDomainMemoryPeek): Likewise.
(qemuDomainGetXMLDesc): Document common flag handling.
* src/libxl/libxl_driver.c (libxlDomainGetXMLDesc): Likewise.
* src/lxc/lxc_driver.c (lxcDomainGetXMLDesc): Likewise.
* src/openvz/openvz_driver.c (openvzDomainGetXMLDesc): Likewise.
* src/phyp/phyp_driver.c (phypDomainGetXMLDesc): Likewise.
* src/test/test_driver.c (testDomainGetXMLDesc): Likewise.
* src/vmware/vmware_driver.c (vmwareDomainGetXMLDesc): Likewise.
* src/xenapi/xenapi_driver.c (xenapiDomainGetXMLDesc): Likewise.
This patch extends qemudDomainSetVcpusFlags() function to support
VIR_DOMAIN_AFFECT_CURRENT flag.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
When qemuMonitorCloseFileHandle is called in error path, we need to
preserve the original error since a possible further error when running
closefd monitor command is not very useful to users.
When creating new qemu process we saved domain status XML only after the
process was fully setup and running. In case libvirtd was killed before
the whole process finished, once libvirtd started again it didn't know
anything about the new process and we end up with an orphaned qemu
process. Let's save the domain status XML as soon as we know the PID so
that libvirtd can kill the process on restart.
The compiler might optimize based on our declaration that something
is unused. Putting that declaration in the header risks getting
out of sync with the actual implementation, so it belongs better
only in the .c files. We were mostly compliant, and a new syntax
check will help us in the future.
* cfg.mk (sc_avoid_attribute_unused_in_header): New syntax check.
* src/nodeinfo.h (nodeGetCPUStats, nodeGetMemoryStats): Delete
attribute already present in .c file.
* src/qemu/qemu_domain.h (qemuDomainEventFlush): Likewise.
* src/util/virterror_internal.h (virReportErrorHelper): Parameters
are actually used by .c file.
* src/xenxs/xen_sxpr.h (xenFormatSxprDisk): Adjust prototype.
* src/xenxs/xen_sxpr.c (xenFormatSxprDisk): Delete unused argument.
(xenFormatSxpr): Adjust caller.
* src/xen/xend_internal.c (xenDaemonAttachDeviceFlags)
(xenDaemonUpdateDeviceFlags): Likewise.
Suggested by Daniel Veillard.
Continuation of commit 313ac7fd, and enforce things with a syntax
check.
Technically, virNetServerClientCalculateHandleMode is not printing
a mode_t, but rather a collection of VIR_EVENT_HANDLE_* bits;
however, these bits are < 8, so there is no different in the
output, and that was the easiest way to silence the new syntax check.
* cfg.mk (sc_flags_debug): New syntax check.
(exclude_file_name_regexp--sc_flags_debug): Add exemptions.
* src/fdstream.c (virFDStreamOpenFileInternal): Print flags in
hex, mode_t in octal.
* src/libvirt-qemu.c (virDomainQemuMonitorCommand)
(virDomainQemuAttach): Likewise.
* src/locking/lock_driver_nop.c (virLockManagerNopInit): Likewise.
* src/locking/lock_driver_sanlock.c (virLockManagerSanlockInit):
Likewise.
* src/locking/lock_manager.c: Likewise.
* src/qemu/qemu_migration.c: Likewise.
* src/qemu/qemu_monitor.c: Likewise.
* src/rpc/virnetserverclient.c
(virNetServerClientCalculateHandleMode): Print mode with %o.
When monitor is entered with qemuDomainObjEnterMonitorWithDriver, the
correct method for leaving and unlocking the monitor is
qemuDomainObjExitMonitorWithDriver.
Most of the code in these two functions is supposed to be identical but
currently it isn't (which is natural since the code is duplicated).
Let's move common parts of these functions into qemuMigrationPrepareAny.
This also fixes qemuMigrationPrepareTunnel which didn't store received
lockState in the domain object.
Asynchronous jobs may take long time to finish and may consist of
several phases which we need to now about to help with recovery/rollback
after libvirtd restarts.
Query commands are safe to be called during long running jobs (such as
migration). This patch makes them all work without the need to
special-case every single one of them.
The patch introduces new job.asyncCond condition and associated
job.asyncJob which are dedicated to asynchronous (from qemu monitor
point of view) jobs that can take arbitrarily long time to finish while
qemu monitor is still usable for other commands.
The existing job.active (and job.cond condition) is used all other
synchronous jobs (including the commands run during async job).
Locking schema is changed to use these two conditions. While asyncJob is
active, only allowed set of synchronous jobs is allowed (the set can be
different according to a particular asyncJob) so any method that
communicates to qemu monitor needs to check if it is allowed to be
executed during current asyncJob (if any). Once the check passes, the
method needs to normally acquire job.cond to ensure no other command is
running. Since domain object lock is released during that time, asyncJob
could have been started in the meantime so the method needs to recheck
the first condition. Then, normal jobs set job.active and asynchronous
jobs set job.asyncJob and optionally change the list of allowed job
groups.
Since asynchronous jobs only set job.asyncJob, other allowed commands
can still be run when domain object is unlocked (when communicating to
remote libvirtd or sleeping). To protect its own internal synchronous
commands, the asynchronous job needs to start a special nested job
before entering qemu monitor. The nested job doesn't check asyncJob, it
only acquires job.cond and sets job.active to block other jobs.
EnterMonitor and ExitMonitor methods are very similar to their
*WithDriver variants; consolidate them into EnterMonitorInternal and
ExitMonitorInternal to avoid (mainly future) code duplication.
The LXC and UML drivers can both make use of auditing. Move
the qemu_audit.{c,h} files to src/conf/domain_audit.{c,h}
* src/conf/domain_audit.c: Rename from src/qemu/qemu_audit.c
* src/conf/domain_audit.h: Rename from src/qemu/qemu_audit.h
* src/Makefile.am: Remove qemu_audit.{c,h}, add domain_audit.{c,h}
* src/qemu/qemu_audit.h, src/qemu/qemu_cgroup.c,
src/qemu/qemu_command.c, src/qemu/qemu_driver.c,
src/qemu/qemu_hotplug.c, src/qemu/qemu_migration.c,
src/qemu/qemu_process.c: Update for changed audit API names
Given a PID, the QEMU driver reads /proc/$PID/cmdline and
/proc/$PID/environ to get the configuration. This is fed
into the ARGV->XML convertor to build an XML configuration
for the process.
/proc/$PID/exe is resolved to identify the full command
binary path
After checking for name/uuid uniqueness, an attempt is
made to connect to the monitor socket. If successful
then 'info status' and 'info kvm' are issued to determine
whether the CPUs are running and if KVM is enabled.
* src/qemu/qemu_driver.c: Implement virDomainQemuAttach
* src/qemu/qemu_process.h, src/qemu/qemu_process.c: Add
qemuProcessAttach to connect to the monitor of an
existing QEMU process
When attaching to an external QEMU process, it is neccessary
to check if the process is using KVM or not. This can be done
using a monitor command
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h,
src/qemu/qemu_monitor_text.c, src/qemu/qemu_monitor_text.h: Add
API for checking if KVM is enabled
To enable attaching to externally launched QEMU, we need
to be able to reverse engineer a guest XML config based
on the argv for a PID in /proc
* src/qemu/qemu_command.c, src/qemu/qemu_command.h: Add
qemuParseCommandLinePid which extracts QEMU config from
argv in /proc, given a PID number
When converting QEMU argv into a virDomainDefPtr, also extract
the pidfile, monitor character device config and the monitor
mode.
* src/qemu/qemu_command.c, src/qemu/qemu_command.h: Extract
pidfile & monitor config from QEMU argv
* src/qemu/qemu_driver.c, tests/qemuargv2xmltest.c: Add extra
params when calling qemuParseCommandLineString
Avoid re-formatting the pidfile path everytime we need it. Create
it once when starting the guest, and preserve it until the guest
is shutdown.
* src/libvirt_private.syms, src/util/util.c,
src/util/util.h: Add virFileReadPidPath
* src/qemu/qemu_domain.h: Add pidfile field
* src/qemu/qemu_process.c: Store pidfile path in qemuDomainObjPrivate
The drivers were accepting domain configs without checking if those
were actually meant for them. For example the LXC driver happily
accepts configs with type QEMU.
Add a check for the expected domain types to the virDomainDefParse*
functions.
If virDomainSaveConfig() failed, we will return NULL to source,
and the vm is still available to restart during confirm() step in
v3 protocol. So we should kill it off in qemuMigrationFinish().
In v2 protocol, we should not set vm to NULL, because we hold
a reference of vm and should unrefernce it.
This patch creates new <bios> element which, at this time has only the
attribute useserial='yes|no'. This attribute allow users to use
Serial Graphics Adapter and see BIOS messages from the very first moment
domain boots up. Therefore, users can choose boot medium, set PXE, etc.
This option accepts 3 values:
-keep, to keep current client connected (Spice+VNC)
-disconnect, to disconnect client (Spice)
-fail, to fail setting password if there is a client connected (Spice)
Add libvirt support for MicroBlaze architecture as a QEMU target. Based on mips/mipsel pattern.
Signed-off-by: John Williams <john.williams@petalogix.com>
Some callers expected virFileMakePath to set errno, some expected
it to return an errno value. Unify this to return 0 on success and
-1 on error. Set errno to report detailed error information.
Also optimize virFileMakePath if stat fails with an errno different
from ENOENT.
add a new API pciDeviceReAttachInit() in pci.c to initialize state values for nodedev reattach
Initialize three state value of device driver to 1. This is just for a new call to
qemudNodeDeviceReAttach()
Although most functions with flags check to verify no application is
passing in flag bits that are currently undefined, for some reason
this function wasn't.
virFileMakePath returns an errno value on error, that will never
be negative. An virFileMakePath error would have been ignored here,
instead of being reported correctly.
Add a new attribute to the <seclabel> XML to allow resource
relabelling to be enabled with static label usage.
<seclabel model='selinux' type='static' relabel='yes'>
<label>system_u:system_r:svirt_t:s0:c392,c662</label>
</seclabel>
* docs/schemas/domain.rng: Add relabel attribute
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parse
the 'relabel' attribute
* src/qemu/qemu_process.c: Unconditionally clear out the
'imagelabel' attribute
* src/security/security_apparmor.c: Skip based on 'relabel'
attribute instead of label type
* src/security/security_selinux.c: Skip based on 'relabel'
attribute instead of label type and fill in <imagelabel>
attribute if relabel is enabled.
Normally the dynamic labelling mode will always use a base
label of 'svirt_t' for VMs. Introduce a <baselabel> field
in the <seclabel> XML to allow this base label to be changed
eg
<seclabel type='dynamic' model='selinux'>
<baselabel>system_u:object_r:virt_t:s0</baselabel>
</seclabel>
* docs/schemas/domain.rng: Add <baselabel>
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parsing
of base label
* src/qemu/qemu_process.c: Don't reset 'model' attribute if
a base label is specified
* src/security/security_apparmor.c: Refuse to support base label
* src/security/security_selinux.c: Use 'baselabel' when generating
label, if available
Detected by Coverity. qemuDomainEventQueue requires a non-NULL
pointer; most callers silently drop the event if we encountered
and OOM situation trying to create the event.
* src/qemu/qemu_migration.c (qemuMigrationFinish): Check for OOM.
Coverity warns if the majority of callers check a function for
errors, but a few don't; but in qemu_audit and qemu_domain, the
choice to not check for failures was safe. In qemu_command, the
failure to generate a uuid can only occur on a bad pointer.
* src/qemu/qemu_audit.c (qemuAuditCgroup): Ignore failure to get
cgroup controller.
* src/qemu/qemu_domain.c (qemuDomainObjEnterMonitor)
(qemuDomainObjEnterMonitorWithDriver): Ignore failure to get
timestamp.
* src/qemu/qemu_command.c (qemuParseCommandLine): Check for error.
The qemudDomainSaveFlag method will call EndJob on the 'vm'
object it is passed in. This can result in the 'vm' object
being free'd if the last reference is removed. Thus no caller
of 'qemudDomainSaveFlag' must *ever* reference 'vm' again
upon return.
Unfortunately qemudDomainSave and qemuDomainManagedSave
both call 'virDomainObjUnlock', which can result in a
crash. This is non-deterministic since it involves a race
with the monitor I/O thread.
Fix this by making qemudDomainSaveFlag responsible for
calling virDomainObjUnlock instead.
* src/qemu/qemu_driver.c: Fix potential use after free
when saving guests
The 'char control[CMSG_SPACE(sizeof(int))];' was not being
wiped, so could potentially contain uninitialized bytes.
While this was harmless in this case, it caused complaints
from valgrind
* src/qemu/qemu_monitor.c: memset 'control' variable
in qemuMonitorIOWriteWithFD
The event handler functions do not free the virJSONValuePtr
object. Every event received from a VM thus caused a memory
leak
* src/qemu/qemu_monitor_json.c: Fix leak of event object
The 'function' field in the PCI address was not correctly
initialized, so it was building the wrong address address
string and so not removing all functions from the in use
list.
* src/qemu/qemu_command.c: Fix initialization of PCI function
If we pass VIR_DOMAIN_AFFECT_LIVE | VIR_DOMAIN_AFFECT_CONFIG to
qemuGetSchedulerParametersFlags() or *nparams is less than 1,
we will unlock qemu_driver without locking it. It's very dangerous.
We should lock qemu_driver after calling virCheckFlags().
Although we create a temporary file, it is owned by root:root and have
rights 0600. In case qemu does not run under root, it is unable to write
to that file and thus we transfer 0B sized file.
Allow a 'configFile' parameter to be passed into the lock
drivers to provide configuration. Wire up the QEMU driver
to pass in file names '/etc/libvirt/qemu-$NAME.conf
eg qemu-sanlock.conf
* src/locking/lock_driver.h, src/locking/lock_driver_nop.c,
src/locking/lock_driver_sanlock.c, src/locking/lock_manager.c,
src/locking/lock_manager.h: Add configFile parameter
* src/qemu/qemu_conf.c: Pass in configuration file path to
lock driver plugins
The libvirt sanlock plugin is intentionally leaking a file
descriptor to QEMU. To enable QEMU to use this FD under
SELinux, it must be labelled correctly. We dont want to use
the svirt_image_t for this, since QEMU must not be allowed
to actually use the FD. So instead we label it with svirt_t
using virSecurityManagerSetProcessFDLabel
* src/locking/domain_lock.c, src/locking/domain_lock.h,
src/locking/lock_driver.h, src/locking/lock_driver_nop.c,
src/locking/lock_driver_sanlock.c, src/locking/lock_manager.c,
src/locking/lock_manager.h: Optionally pass an FD back to
the hypervisor for security driver labelling
* src/qemu/qemu_process.c: label the lock manager plugin
FD with the process label
The virSecurityManagerSetFDLabel method is used to label
file descriptors associated with disk images. There will
shortly be a need to label other file descriptors in a
different way. So the current name is ambiguous. Rename
the method to virSecurityManagerSetImageFDLabel to clarify
its purpose
* src/libvirt_private.syms,
src/qemu/qemu_migration.c, src/qemu/qemu_process.c,
src/security/security_apparmor.c, src/security/security_dac.c,
src/security/security_driver.h, src/security/security_manager.c,
src/security/security_manager.h, src/security/security_selinux.c,
src/security/security_stack.c: s/FDLabel/ImageFDLabel/
We already have a public virDomainPinVcpu, which implies that
Pin and Vcpu are treated as separate words. Unreleased commit
e261987c introduced virDomainGetVcpupinInfo as the first public
API that used Vcpupin, although we had prior internal uses of
that spelling. For consistency, change the spelling to be two
words everywhere, regardless of whether pin comes first or last.
* daemon/remote.c: Treat vcpu and pin as separate words.
* include/libvirt/libvirt.h.in: Likewise.
* src/conf/domain_conf.c: Likewise.
* src/conf/domain_conf.h: Likewise.
* src/driver.h: Likewise.
* src/libvirt.c: Likewise.
* src/libvirt_private.syms: Likewise.
* src/libvirt_public.syms: Likewise.
* src/libxl/libxl_driver.c: Likewise.
* src/qemu/qemu_driver.c: Likewise.
* src/remote/remote_driver.c: Likewise.
* src/xen/xend_internal.c: Likewise.
* tools/virsh.c: Likewise.
* src/remote/remote_protocol.x: Likewise.
* src/remote_protocol-structs: Likewise.
Suggested by Matthias Bolte.
This patch implements the code to address the new API (virDomainGetVcpupinInfo)
in the qemu driver.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Use NUMA's older nodemask_t (fixed-size map) rather than the newer
'struct bitmask' (variable-size) in order to still compile on RHEL 5,
with its numactl-devel-0.9.8.
* src/qemu/qemu_process.c [HAVE_NUMA]: Prefer back-compat mode.
(qemuProcessInitNumaMemoryPolicy): Use older nodemask_t.
The qemuMigrationPrepareDirect/PrepareTunnel methods accidentally
set the domain job to QEMU_JOB_MIGRATION_OUT when it should have
been QEMU_JOB_MIGRATION_IN. This didn't have any ill-effect, but
it is none-the-less wrong.
* src/qemu/qemu_migration.c: Fix job type
The code emitting taint warnings was mistakenly thinking
that guests run from the QEMU session driver were tainted
for having high privileges. This is of course nonsense
since the session driver is always unprivileged
* src/qemu/qemu_domain.c: Don't warn for high privileges in
non-privileged QEMU
If an application is using libvirt + KVM as a piece of its
internal infrastructure to perform a specific task, it can
be desirable to guarentee the VM dies when the virConnectPtr
disconnects from libvirtd. This ensures the app can't leak
any VMs it was using. Adding VIR_DOMAIN_START_AUTOKILL as
a flag when starting guests enables this to be done.
* include/libvirt/libvirt.h.in: All VIR_DOMAIN_START_AUTOKILL
* src/qemu/qemu_driver.c: Support automatic killing of guests
upon connection close
* tools/virsh.c: Add --autokill flag to 'start' and 'create'
commands
Migration is a multi-step process
1. Begin(src)
2. Prepare(dst)
3. Perform(src)
4. Finish(dst)
5. Confirm(src)
At step 2, a QEMU process is lauched in the destination to
accept the incoming migration. Occasionally the process
that is controlling the migration workflow aborts, and fails
to call step 4, Finish. This leaves a QEMU process running
on the target (albeit with paused CPUs). Unfortunately because
step 2 actives a job on the QEMU process, it is unkillable by
normal means.
By registering the VM for autokill against the src virConnectPtr
in step 2, we can ensure that the guest is forcefully killed off
if the connection is closed without step 4 being invoked
* src/qemu/qemu_migration.c: Register autokill in PrepareDirect
and PrepareTunnel. Unregister autokill on successful run
of Finish
* src/qemu/qemu_process.c: Unregister autokill when stopping a
process
Sometimes it is useful to be able to automatically destroy a guest when
a connection is closed. For example, kill an incoming migration if
the client managing the migration dies. This introduces a map between
guest 'uuid' strings and virConnectPtr objects. When a connection is
closed, any associated guests are killed off.
* src/qemu/qemu_conf.h: Add autokill hash table to qemu driver
* src/qemu/qemu_process.c, src/qemu/qemu_process.h: Add APIs
for performing autokill of guests associated with a connection
* src/qemu/qemu_driver.c: Initialize autodestroy map
For controlled shutdown we issue a 'system_powerdown' command
to the QEMU monitor. This triggers an ACPI event which (most)
guest OS wire up to a controlled shutdown. There is no equiv
ACPI event to trigger a controlled reboot. This patch attempts
to fake a reboot.
- In qemuDomainObjPrivatePtr we have a bool fakeReboot
flag.
- The virDomainReboot method sets this flag and then
triggers a normal 'system_powerdown'.
- The QEMU process is started with '-no-shutdown'
so that the guest CPUs pause when it powers off the
guest
- When we receive the 'POWEROFF' event from QEMU JSON
monitor if fakeReboot is not set we invoke the
qemuProcessKill command and shutdown continues
normally
- If fakeReboot was set, we spawn a background thread
which issues 'system_reset' to perform a warm reboot
of the guest hardware. Then it issues 'cont' to
start the CPUs again
* src/qemu/qemu_command.c: Add -no-shutdown flag if
we have JSON support
* src/qemu/qemu_domain.h: Add 'fakeReboot' flag to
qemuDomainObjPrivate struct
* src/qemu/qemu_driver.c: Fake reboot using the
system_powerdown command if JSON support is available
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h,
src/qemu/qemu_monitor_text.c, src/qemu/qemu_monitor_text.h: Add
binding for system_reset command
* src/qemu/qemu_process.c: Reset the guest & start CPUs if
fakeReboot is set
GCC complained about a C99 for-loop declaration outside of C99 mode
when compiling on RHEL 5.
* src/qemu/qemu_driver.c (qemudDomainPinVcpuFlags): Avoid C99 for
loop, since gcc 4.1.2 hates it.
For virtio disks and interfaces, qemu allows users to enable or disable
ioeventfd feature. This means, qemu can execute domain code, while
another thread waits for I/O event. Basically, in some cases it is win,
in some loss. This feature is available via 'ioeventfd' attribute in disk
and interface <driver> element. It accepts 'on' and 'off'. Leaving this
attribute out defaults to hypervisor decision.
The following patch addresses the problem that when a PASSTHROUGH
mode DIRECT NIC connection is made the MAC address of the NIC is
not automatically set and reset to the configured VM MAC and
back again.
The attached patch fixes this problem by setting and resetting the MAC
while remembering the previous setting while the VM is running.
This also works if libvirtd is restarted while the VM is running.
the patch passes make syntax-check
Since we virEventRegisterDefaultImpl is now a public API, callers need
a way to invoke the default registered Handle and Timeout functions. We
already have general functions for these internally, so promote
them to the public API.
v2:
Actually add APIs to libvirt.h
Pinning to all physical cpus means resetting, hence it is preferable to
delete vcpupin setting of XML.
This patch changes qemu driver to delete vcpupin setting by invoking
virDomainVcpupinDel API when pinning the specified virtual cpu to
all host physical cpus.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Implemented as setting NUMA policy between fork and exec as a hook,
using libnuma. Only support memory tuning on domain process currently.
For the nodemask out of range, will report soft warning instead of
hard error in libvirt layer. (Kernel will be silent as long as one
of set bit in the nodemask is valid on the host. E.g. For a host
has two NUMA nodes, kernel will be silent for nodemask "01010101").
So, soft warning is the only thing libvirt can do, as one might want
to specify the numa policy prior to a node that doesn't exist yet,
however, it may come as hotplug soon.
If the 'mac_filter' configuration parameter is enabled, and there
is a failure to enable filtering, no error is reported back to
the caller. Also fix some bogus whitespace indentation for
hugetlbfs_mount
* src/qemu/qemu_conf.c: Add missing error reporting
Prefer bootindex=N option for -device over the old way -boot ORDER
possibly accompanied with boot=on option for -drive. This gives us full
control over which device will actually be used for booting guest OS.
Moreover, if qemu doesn't support boot=on, this is the only way to boot
of certain disks in some configurations (such as virtio disks when used
together IDE disks) without transforming domain XML to use per device
boot elements.
When an operation started by virDomainBlockPullAll completes (either with
success or with failure), raise an event to indicate the final status. This
allows an API user to avoid polling on virDomainBlockPullInfo if they would
prefer to use the event mechanism.
* daemon/remote.c: Dispatch events to client
* include/libvirt/libvirt.h.in: Define event ID and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Extend API to handle the new event
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
for block_stream completion and emit a libvirt block pull event
* src/remote/remote_driver.c: Receive and dispatch events to application
* src/remote/remote_protocol.x: Wire protocol definition for the event
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c: Watch for BLOCK_STREAM_COMPLETED event
from QEMU monitor
Signed-off-by: Adam Litke <agl@us.ibm.com>
The virDomainBlockPull* family of commands are enabled by the
'block_stream' and 'info block_stream' qemu monitor commands.
* src/qemu/qemu_driver.c src/qemu/qemu_monitor_text.[ch]: implement disk
streaming by using the stream and info stream text monitor commands
* src/qemu/qemu_monitor_json.[ch]: implement commands using the qmp monitor
Signed-off-by: Adam Litke <agl@us.ibm.com>
Acked-by: Daniel P. Berrange <berrange@redhat.com>
From a security pov copy and paste between the guest and the client is not
always desirable. So we need to be able to enable/disable this. The best place
to do this from an administration pov is on the hypervisor, so the qemu cmdline
is getting a spice disable-copy-paste option, see bug 693645. Example qemu
invocation:
qemu -spice port=5932,disable-ticketing,disable-copy-paste
https://bugzilla.redhat.com/show_bug.cgi?id=693661
If qemu supports -chardev, our char frontend aliases are ex. 'charserial0'
not just 'serial0'. Typically we don't use this code path because the
pty's are scraped from stdout.
Qemu once supported following memory stats which will returned by
"query_balloon":
stat_put(dict, "actual", actual);
stat_put(dict, "mem_swapped_in", dev->stats[VIRTIO_BALLOON_S_SWAP_IN]);
stat_put(dict, "mem_swapped_out", dev->stats[VIRTIO_BALLOON_S_SWAP_OUT]);
stat_put(dict, "major_page_faults", dev->stats[VIRTIO_BALLOON_S_MAJFLT]);
stat_put(dict, "minor_page_faults", dev->stats[VIRTIO_BALLOON_S_MINFLT]);
stat_put(dict, "free_mem", dev->stats[VIRTIO_BALLOON_S_MEMFREE]);
stat_put(dict, "total_mem", dev->stats[VIRTIO_BALLOON_S_MEMTOT]);
But it later disabled all the stats except "actual" by commit
07b0403dfc2b2ac179ae5b48105096cc2d03375a.
libvirt doesn't parse "actual", so user will always see a empty result
with "virsh dommemstat $domain". Even qemu haven't disabled the stats,
we should support parsing "actual".
There is the case where cpu affinites for vcpu of qemu doesn't work
correctly. For example, if only one vcpupin setting entry is provided
and its setting is not for vcpu0, it doesn't work.
# virsh dumpxml VM
...
<vcpu>4</vcpu>
<cputune>
<vcpupin vcpu='3' cpuset='9-11'/>
</cputune>
...
# virsh start VM
Domain VM started
# virsh vcpuinfo VM
VCPU: 0
CPU: 31
State: running
CPU time: 2.5s
CPU Affinity: yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
VCPU: 1
CPU: 12
State: running
CPU time: 0.9s
CPU Affinity: yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
VCPU: 2
CPU: 30
State: running
CPU time: 1.5s
CPU Affinity: yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
VCPU: 3
CPU: 13
State: running
CPU time: 1.7s
CPU Affinity: yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
This patch fixes this problem.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
This patch deprecates following enums:
VIR_DOMAIN_MEM_CURRENT
VIR_DOMAIN_MEM_LIVE
VIR_DOMAIN_MEM_CONFIG
VIR_DOMAIN_VCPU_LIVE
VIR_DOMAIN_VCPU_CONFIG
VIR_DOMAIN_DEVICE_MODIFY_CURRENT
VIR_DOMAIN_DEVICE_MODIFY_LIVE
VIR_DOMAIN_DEVICE_MODIFY_CONFIG
And modify internal codes to use virDomainModificationImpact.
The below patch decreases the response time of libvirt to errors reported by Qemu upon startup by checking whether the qemu process is still alive while polling for the local socket to show up.
This patch also introduces a special handling of signal for the Win32 part of virKillProcess.
If qemu supports multi function PCI device, the format of the PCI address passed
to qemu is "bus=pci.0,multifunction=on,addr=slot.function".
If qemu does not support multi function PCI device, the format of the PCI address
passed to qemu is "bus=pci.0,addr=slot".
Hot pluging/unpluging multi PCI device is not supported now. So the function
of hotplugged PCI device must be 0. When we hot unplug it, we should set release
all functions in the slot.
We save all used PCI address in the hash table. The key is generated by domain,
bus and slot now. We will support multi function PCI device, so the key should
be generated by domain, bus, slot and function.
We do not support to hot unplug multi function PCI device now. If the device is
one function of multi function PCI device, we shoul not allow to hot unplugg
it.
Detected by Coverity. All existing callers happen to be in
range, so this isn't too serious.
* src/qemu/qemu_cgroup.c (qemuCgroupControllerActive): Check
bounds before dereference.
When peer-2-peer migration was invoked by a client supporting
v3, but where the target server only supported v2, we'd not
correctly shutdown the guest.
* src/qemu/qemu_migration.c: Ensure guest is shutdown in
v2 peer 2 peer migration
The v2 migration protocol doesn't use cookies, so we should not
be raising an error if the cookie parameters are NULL.
* src/qemu/qemu_migration.c: Don't raise error if cookie is NULL
The error code for virKillProcess is returned in the errno variable
not the return value. THis mistake caused the logs to be filled with
errors when shutting down QEMU processes
* src/qemu/qemu_process.c: Fix process kill check.
This commit is safe precisely because there has been no release
for any of the enum values being deleted (they were added post-0.9.1).
After the 0.9.2 release, we can then take advantage of
virDomainModificationImpact in more places.
* include/libvirt/libvirt.h.in (virDomainModificationImpact): New
enum.
(virDomainSchedParameterFlags, virMemoryParamFlags): Delete, since
these were never released, and the new enum works fine here.
* src/libvirt.c (virDomainGetMemoryParameters)
(virDomainSetMemoryParameters)
(virDomainGetSchedulerParametersFlags)
(virDomainSetSchedulerParametersFlags): Update documentation.
* src/qemu/qemu_driver.c (qemuDomainSetMemoryParameters)
(qemuDomainGetMemoryParameters, qemuSetSchedulerParametersFlags)
(qemuSetSchedulerParameters, qemuGetSchedulerParametersFlags)
(qemuGetSchedulerParameters): Adjust clients.
* tools/virsh.c (cmdSchedinfo, cmdMemtune): Likewise.
Based on ideas by Daniel Veillard and Hu Tao.
Detected by Coverity. This leaked a cpumap on every iteration
of the loop. Leak introduced in commit 1cc4d02 (v0.9.0).
* src/qemu/qemu_process.c (qemuProcessSetVcpuAffinites): Plug
leak, and hoist allocation outside loop.
In v3 migration, once migration is completed, the VM needs
to be left in a paused state until after Finish3 has been
executed on the target. Only then will the VM be killed
off. When using non-JSON QEMU monitor though, we don't
receive any 'STOP' event from QEMU, so we need to manually
set our state offline & thus release lock manager leases.
It doesn't hurt to run this on the JSON case too, just in
case the event gets lost somehow
* src/qemu/qemu_migration.c: Explicitly set VM state to
paused when migration completes
The change 18c2a59206 caused
some regressions in behaviour of virDomainBlockStats
and virDomainBlockInfo in the QEMU driver.
The virDomainBlockInfo API stopped working for inactive
guests if querying a block device.
The virDomainBlockStats API did not promptly report
an error if the guest was not running in some cases.
* src/qemu/qemu_driver.c: Fix inactive guest handling
in BlockStats/Info APIs
The qemuAuditDisk calls in disk hotunplug operations were being
passed 'ret >= 0', but the code which sets ret to 0 was not yet
executed, and the error path had already jumped to the 'cleanup'
label. This meant hotunplug failures were never audited, and
hotunplug success was audited as a failure
* src/qemu/qemu_hotplug.c: Fix auditing of hotunplug
Commit 4454a9efc7 introduced bad
behaviour on the VIR_EVENT_HANDLE_ERROR condition. This condition
is only hit when an invalid FD is used in poll() (typically due
to a double-close bug). The QEMU monitor code was treating this
condition as non-fatal, and thus libvirt would poll() in a fast
loop forever burning 100% CPU. VIR_EVENT_HANDLE_ERROR must be
handled in the same way as VIR_EVENT_HANDLE_HANGUP, killing the
QEMU instance.
* src/qemu/qemu_monitor.c: Treat VIR_EVENT_HANDLE_ERROR as EOF
* src/conf/domain_conf.c, src/conf/domain_conf.h: APIs for
inserting/finding/removing virDomainLeaseDefPtr instances
* src/qemu/qemu_driver.c: Wire up hotplug/unplug for leases
* src/qemu/qemu_hotplug.h, src/qemu/qemu_hotplug.c: Support
for hotplug and unplug of leases
Some lock managers associate state with leases, allowing a process
to temporarily release its leases, and re-acquire them later, safe
in the knowledge that no other process has acquired + released the
leases in between.
This is already used between suspend/resume operations, and must
also be used across migration. This passes the lockstate in the
migration cookie. If the lock manager uses lockstate, then it
becomes compulsory to use the migration v3 protocol to get the
cookie support.
* src/qemu/qemu_driver.c: Validate that migration v2 protocol is
not used if lock manager needs state transfer
* src/qemu/qemu_migration.c: Transfer lock state in migration
cookie XML
The QEMU integrates with the lock manager instructure in a number
of key places
* During startup, a lock is acquired in between the fork & exec
* During startup, the libvirtd process acquires a lock before
setting file labelling
* During shutdown, the libvirtd process acquires a lock
before restoring file labelling
* During hotplug, unplug & media change the libvirtd process
holds a lock while setting/restoring labels
The main content lock is only ever held by the QEMU child process,
or libvirtd during VM shutdown. The rest of the operations only
require libvirtd to hold the metadata locks, relying on the active
QEMU still holding the content lock.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h,
src/qemu/libvirtd_qemu.aug, src/qemu/test_libvirtd_qemu.aug:
Add config parameter for configuring lock managers
* src/qemu/qemu_driver.c: Add calls to the lock manager
Update the qemuDomainMigrateBegin method so that it accepts
an optional incoming XML document. This will be validated
for ABI compatibility against the current domain config,
and if this check passes, will be passed back out for use
by the qemuDomainMigratePrepare method on the target
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h,
src/qemu/qemu_migration.c: Allow custom XML to be passed
Currently the QEMU monitor I/O handler code uses errno values
to report errors. This results in a sub-optimal error messages
on certain conditions, in particular when parsing JSON strings
malformed data simply results in 'EINVAL'.
This changes the code to use the standard libvirt error reporting
APIs. The virError is stored against the qemuMonitorPtr struct,
and when a monitor API is run, any existing stored error is copied
into that thread's error local
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_text.c: Use
virError APIs for all monitor I/O handling code
Currently whenever there is any failure with parsing the monitor,
this is treated in the same was as end-of-file (ie QEMU quit).
The domain is terminated, if not already dead.
With this change, failures in parsing the monitor stream do not
result in the death of QEMU. The guest continues running unchanged,
but all further use of the monitor will be disabled.
The VMM_FAILURE event will be emitted, and the mgmt application
can decide when to kill/restart the guest to re-gain control
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h: Run a
different callback for monitor EOF vs error conditions.
* src/qemu/qemu_process.c: Emit VMM_FAILURE event when monitor
fails
* src/qemu/qemu_driver.c (qemuGetSchedulerParameters): Move
guts...
(qemuGetSchedulerParametersFlags): ...to new callback, and honor
flags more accurately.
This patch allows to modify interfaces of domain(qemu)
* src/conf/domain_conf.c src/conf/domain_conf.h src/libvirt_private.syms:
(virDomainNetInsert) : Insert a network device to domain definition.
(virDomainNetIndexByMac) : Returns an index of net device in array.
(virDomainNetRemoveByMac): Remove a NIC of passed MAC address.
* src/qemu/qemu_driver.c
(qemuDomainAttachDeviceConfig): add codes for NIC.
(qemuDomainDetachDeviceConfig): add codes for NIC.
Originally most of libvirt domain-specific calls were blocking
during a migration.
A new mechanism to allow specific calls (blkstat/blkinfo) to be
executed in such condition has been implemented.
In the long term it'd be desirable to get a more general
solution to mark further APIs as migration safe, without needing
special case code.
* src/qemu/qemu_migration.c: add some additional job signal
flags for doing blkstat/blkinfo during a migration
* src/qemu/qemu_domain.c: add a condition variable that can be
used to efficiently wait for the migration code to clear the
signal flag
* src/qemu/qemu_driver.c: execute blkstat/blkinfo using the
job signal flags during migration
When modifying the disk devices of a live domain and the domain
configuration, the function qemuDomainAttachDeviceConfig
first sets dev->data->disk to NULL. Later qemuDomainAttachDeviceLive
accesses dev->data.disk and causes a segfault.
* src/qemu/qemu_driver.c: fix qemuDomainModifyDeviceFlags() accordingly
http://lists.gnu.org/archive/html/qemu-devel/2011-05/threads.html#02162
Currently, qemu silently clips any JSON integer in the range
0x8000000000000000 - 0xffffffffffffffff (all numbers in this range
will be clipped to 0x7fffffffffffffff == LLONG_MAX).
To avoid this, pass these as signed 64 bit integers in the QMP
request.
The current virDomainMigrateFinish3 method signature attempts to
distinguish two types of errors, by allowing return with ret== 0,
but ddomain == NULL, to indicate a failure to start the guest.
This is flawed, because when ret == 0, there is no way for the
virErrorPtr details to be sent back to the client.
Change the signature of virDomainMigrateFinish3 so it simply
returns a virDomainPtr, in the same way as virDomainMigrateFinish2
The disk locking code will protect against the only possible
failure mode this doesn't account for (loosing conenctivity to
libvirtd after Finish3 starts the CPUs, but before the client
sees the reply for Finish3).
* src/driver.h, src/libvirt.c, src/libvirt_internal.h: Change
virDomainMigrateFinish3 to return a virDomainPtr instead of int
* src/remote/remote_driver.c, src/remote/remote_protocol.x,
daemon/remote.c, src/qemu/qemu_driver.c, src/qemu/qemu_migration.c:
Update for API change
When doing migration, if an error occurs in Perform, it must not
be overwritten during Finish/Confirm steps. If an error occurs
in Finish, it must not be overwritten in Confirm.
Previous commit a9d12c2444 added
code to qemudDomainMigrateFinish2 to preserve the error. This
is not the right place, because it is not applicable in non-p2p
migration. The src/libvirt.c virDomainMigrateV2/3 methods need
code to preserve errors for non-p2p migration, while the
doPeer2PeerMigrate2 and doPeer2PeerMigrate3 methods contain
code to preverse errors for p2p migration.
Remove the bogus error preservation from qemudDomainMigrateFinish2
and qemudDomainMigrateFinish3.
Fix virDomainMigrateV3 and doPeer2PeerMigrate3 so that they
preserve any error hit during the Finish3 step, before invoking
Confirm3.
Finally if qemuMigrationFinish fails to resume the CPUs, it must
preserve the error before tearing down the VM, so that VM cleanup
doesn't overwrite it.
* src/libvirt.c: Preserve error before invoking Confirm3
* src/qemu/qemu_driver.c: Remove bogus error preservation
code in qemudDomainMigrateFinish2/qemudDomainMigrateFinish3
* src/qemu/qemu_migration.c: Preserve error before invoking Confirm3
and after resume fails in qemuMigrationFinish.
* src/libvirt.c: Add further debug lines in helper APIs for
migration
* src/qemu/qemu_migration.c: Add debug lines for all internal
migration API parameters
Even when failing to start CPUs, the finish method was returning
a success result. Fix this so that the QEMU process is killed
off when finish fails under v3 protocol. Also rename the
killOnFinish boolean to 'v3proto' to make it clearer that this
is a tunable based on the migration protocol version
* src/qemu/qemu_driver.c: Update for API change
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Kill
VM in qemuMigrationFinish if failing to start CPUs
The SPICE seamless migration process requires data to be passed
back from the target host, to the source host via a cookie.
The cookie includes the target host's hostname, but this was not
stored, merely validated. This patch explicitly records the
remote hostname after parsing the cookie, and uses it when
initiating the SPICE migration
* qemu/qemu_migration.c: Fix SPICE seamless migration hostname
Before running perform in peer-2-peer migration, the current
guest state must be recorded, so that non-live migration can
currently unpause a running guest on completion.
* src/qemu/qemu_migration.c: Move check for offline guest
to fix non-live migration
The virDomainMigratePerform3 currently has a single URI parameter
whose meaning varies. It is either
- A QEMU migration URI (normal migration)
- A libvirtd connection URI (peer2peer migration)
Unfortunately when using peer2peer migration, without also
using tunnelled migration, it is possible that both URIs are
required.
This adds a second URI parameter to the virDomainMigratePerform3
method, to cope with this scenario. Each parameter how has a fixed
meaning.
NB, there is no way to actually take advantage of this yet,
since virDomainMigrate/virDomainMigrateToURI do not have any
way to provide the 2 separate URIs
* daemon/remote.c, src/remote/remote_driver.c,
src/remote/remote_protocol.x, src/remote_protocol-structs: Add
the second URI parameter to perform3 message
* src/driver.h, src/libvirt.c, src/libvirt_internal.h: Add
the second URI parameter to Perform3 method
* src/libvirt_internal.h, src/qemu/qemu_migration.c,
src/qemu/qemu_migration.h: Update to handle URIs correctly
This extends the v3 migration protocol such that the
virDomainMigrateBegin3 and virDomainMigratePerform3
methods accept an application supplied XML config for
the target VM.
If the 'xmlin' parameter is NULL, then Begin3 uses the
current guest XML as normal. A driver implementing the
Begin3 method should either reject all non-NULL 'xmlin'
parameters, or strictly validate that the app supplied
XML does not change guest ABI.
The Perform3 method also needed the xmlin parameter to
cope with the Peer2Peer migration sequence.
NB it is not yet possible to use this capability since
neither of the public virDomainMigrate/virDomainMigrateToURI
methods have a way to pass in XML.
* daemon/remote.c, src/remote/remote_driver.c,
src/remote/remote_protocol.x, src/remote_protocol-structs:
Add 'remote_string xmlin' parameter to begin3/perform3
RPC messages
* src/libvirt.c, src/driver.h, src/libvirt_internal.h: Add
'const char *xmlin' parameter to Begin3/Perform3 methods
* src/qemu/qemu_driver.c, src/qemu/qemu_migration.c,
src/qemu/qemu_migration.h: Pass xmlin parameter around
migration methods
Saving domain to previously created file changes also its ownership.
This is certainly not what users want if some conditions are met:
it is a regular, local file and dynamic_ownership is off.
NB: the enum that uses the string vnet-host (now changed to vhost-net)
is used in XML, but fortunately that hasn't been in an official
release yet, so it can still be fixed.
Since -vnc uses ':' to separate the address from the port, raw
IPv6 addresses need to be escaped like [addr]:port
* src/qemu/qemu_command.c: Escape raw IPv6 addresses with []
* tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.args,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.xml: Tweak
to test Ipv6 escaping
* docs/schemas/domain.rng: Allow Ipv6 addresses, or hostnames
in <graphics> listen attributes
The qemuMigrationConfirm method shouldn't deal with final VM
cleanup, since it can be called from the peer2peer migration,
which expects to still use the 'vm' object afterwards.
Push the cleanup code out of qemuMigrationConfirm, into its
caller, qemuDomainMigrateConfirm3
* src/qemu/qemu_driver.c: Add VM cleanup code to
qemuDomainMigrateConfirm3
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Remove
job handling cleanup from qemuMigrationConfirm
To allow new mandatory migration cookie data to be introduced,
add support for checking supported feature flags when parsing
migration cookie.
* src/qemu/qemu_migration.c: Feature flag checking in migration
cookie parsing
This adds a streaming-video=filter|all|off attribute. It is used to change
the behavior of video stream detection in spice, the default is filter (the
default for libvirt is not to specify it - the actual default is defined in
libspice-server.so).
Usage:
<graphics type='spice' autoport='yes'>
<streaming mode='off'/>
</graphics>
Tested with the above and with tests/qemuxml2argvtest.
Signed-off-by: Alon Levy <alevy@redhat.com>
This was discussed in:
https://www.redhat.com/archives/libvir-list/2011-May/msg01370.html
The capabilities code only sets the flag to allow use of vhost-net if
kvm is detected (set if the help string contains "(qemu-kvm-" or
"(kvm-"), but actually vhost-net is available in some qemu builds that
don't have kvm in their name, so just checking for ",vhost=" is enough.
Otherwise qemu is unable to write to it, with the error:
libvir: QEMU error : internal error unable to execute QEMU command 'memsave': Could not open '/var/cache/libvirt/qemu/qemu.mem.RRNvLv'
The v2 migration protocol had a limit on cookie length that was
too small to be useful for QEMU. Avoid generating cookies with
v2 protocol, so that old libvirtd can still reliably migrate a
guest to new libvirtd uses v2 protocol.
* src/qemu/qemu_driver.c: Avoid migration cookies with v2
migration
When generating a cookie for a guest with no data, the
QEMU_MIGRATION_COOKIE_GRAPHICS flag was set even if no
graphics data was added. Avoid setting the flag unless
it was needed, also add a safety check for mig->graphics
being non-NULL
* src/qemu/qemu_migration.c: Avoid cookie crash for guest
with no graphics
Improve invalid argument checks in the size query case. The drivers already
relied on this unchecked behavior.
Relax the implementation of virDomainGet(Memory|Blkio)MemoryParameters
in the drivers and allow to pass more memory than necessary for all
parameters.
params and nparams are essential and cannot be NULL. Check this in
libvirt.c and remove redundant checks from the drivers (e.g. xend).
Instead of enforcing that nparams must point to exact same value as
returned by virDomainGetSchedulerType relax this to a lower bound
check. This is what some drivers (e.g. xen hypervisor and esx)
already did. Other drivers (e.g. xend) didn't check nparams at all
and assumed that there is enough space in params.
Unify the behavior in all drivers to a lower bound check and update
nparams to the number of valid values in params on success.
By running the doTunnelSendAll code in a separate thread, the
main thread can do qemuMigrationWaitForCompletion as with
normal migration. This in turn ensures that job signals work
correctly and that progress monitoring can be done
* src/qemu/qemu_migration.c: Run tunnelled migration in
separate thread
Cancelling the QEMU migration may cause QEMU to flush pending
data on the migration socket. This may in turn block QEMU if
nothing reads from the other end of the socket. Closing the
socket before cancelling QEMU migration avoids this possible
deadlock.
* src/qemu/qemu_migration.c: Close sockets before cancelling
migration on failure
The 'nbytes' variable was not re-initialized to the
buffer size on each iteration of the tunnelled migration
loop. While saferead() will ensure a full read, except
on EOF, it is clearer to use the real buffer size
* src/qemu/qemu_migration.c: Always read full buffer of data
The qemuMigrationWaitForCompletion method contains a loop which
repeatedly queries QEMU to check migration progress, and also
processes job signals (pause, setspeed, setbandwidth, cancel).
The tunnelled migration loop does not currently support this
functionality, but should. Refactor the code to allow it to
be used with tunnelled migration.
Implement the v3 migration protocol, which has two extra
steps, 'begin' on the source host and 'confirm' on the
source host. All other methods also gain both input and
output cookies to allow bi-directional data passing at
all stages.
The QEMU peer2peer migration method gains another impl
to provide the v3 migration. This finally allows migration
cookies to work with tunnelled migration, which is required
for Spice seamless migration & the lock manager transfer
* src/qemu/qemu_driver.c: Wire up migrate v3 APIs
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Add
begin & confirm methods, and peer2peer impl of v3
Merge the doNonTunnelMigrate2 and doTunnelMigrate2 methods
into one doPeer2PeerMigrate2 method, since they are substantially
the same. With the introduction of v3 migration, this will be
even more important, to avoid massive code duplication.
* src/qemu/qemu_migration.c: Merge tunnel & non-tunnel migration
To facilitate the introduction of the v3 migration protocol,
the doTunnelMigrate method is refactored into two pieces. One
piece is intended to mirror the flow of virDomainMigrateVersion2,
while the other is the helper for setting up sockets and processing
the data.
Previously socket setup would be done before the 'prepare' step,
so errors could be dealt with immediately, avoiding need to shut
off the destination QEMU. In the new split, socket setup is done
after the 'prepare' step. This is not a serious problem, since
the control flow already requires calling 'finish' to tear down
the destination QEMU upon several errors.
* src/qemu/qemu_migration.c:
Use the graphics information from the QEMU migration cookie to
issue a 'client_migrate_info' monitor command to QEMU. This causes
the SPICE client to automatically reconnect to the target host
when migration completes
* src/qemu/qemu_migration.c: Set data for SPICE client relocation
before starting migration on src
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h,
src/qemu/qemu_monitor_text.c, src/qemu/qemu_monitor_text.h: Add
new qemuMonitorGraphicsRelocate() command
Extend the QEMU migration cookie structure to allow information
about the destination host graphics setup to be passed by to
the source host. This will enable seamless migration of any
connected graphics clients
* src/qemu/qemu_migration.c: Add graphics info to migration
cookies
* daemon/libvirtd.c: Always initialize gnutls to enable
x509 cert parsing in QEMU
The migration protocol has support for a 'cookie' parameter which
is an opaque array of bytes as far as libvirt is concerned. Drivers
may use this for passing around arbitrary extra data they might
need during migration. The QEMU driver needs to do a few things:
- Pass hostname/uuid to allow strict protection against localhost
migration attempts
- Pass SPICE/VNC server port from the target back to the source to
allow seamless relocation of client sessions
- Pass lock driver state from source to destination
This patch introduces the basic glue for handling cookies
but only includes the host/guest UUID & name.
* src/libvirt_private.syms: Export virXMLParseStrHelper
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Parsing
and formatting of migration cookies
* src/qemu/qemu_driver.c: Pass in cookie parameters where possible
* src/remote/remote_protocol.h, src/remote/remote_protocol.x: Change
cookie max length to 16384 bytes
The qemuMigrationPrepareTunnel method should not unlock the
qemu driver, since that is the caller's job.
* src/qemu/qemu_migration.c: Fix qemuMigrationPrepareTunnel
unlocking of QEMU driver
Change all the driver struct initializers to use the
C99 style, leaving out unused fields. This will make
it possible to add new APIs without changing every
driver. eg change:
qemudDomainResume, /* domainResume */
qemudDomainShutdown, /* domainShutdown */
NULL, /* domainReboot */
qemudDomainDestroy, /* domainDestroy */
to
.domainResume = qemudDomainResume,
.domainShutdown = qemudDomainShutdown,
.domainDestroy = qemudDomainDestroy,
And get rid of any existing C99 style initializersr which
set NULL, eg change
.listPools = vboxStorageListPools,
.numOfDefinedPools = NULL,
.listDefinedPools = NULL,
.findPoolSources = NULL,
.poolLookupByName = vboxStoragePoolLookupByName,
to
.listPools = vboxStorageListPools,
.poolLookupByName = vboxStoragePoolLookupByName,
Fix some driver names:
s/virDrvCPUCompare/virDrvCompareCPU/
s/virDrvCPUBaseline/virDrvBaselineCPU/
s/virDrvQemuDomainMonitorCommand/virDrvDomainQemuMonitorCommand/
s/virDrvSecretNumOfSecrets/virDrvNumOfSecrets/
s/virDrvSecretListSecrets/virDrvListSecrets/
And some driver struct field names:
s/getFreeMemory/nodeGetFreeMemory/
Only in drivers which use virDomainObj, drivers that query hypervisor
for domain status need to be updated separately in case their hypervisor
supports this functionality.
The reason is also saved into domain state XML so if a domain is not
running (i.e., no state XML exists) the reason will be lost by libvirtd
restart. I think this is an acceptable limitation.
This is needed if we want to transfer a temporary file. If the
transfer is done with iohelper, we might run into a race condition,
where we unlink() file before iohelper is executed.
* src/fdstream.c, src/fdstream.h,
src/util/iohelper.c: Add new option
* src/lxc/lxc_driver.c, src/qemu/qemu_driver.c,
src/storage/storage_driver.c, src/uml/uml_driver.c,
src/xen/xen_driver.c: Expand existing function calls
We were 31/73 on whether to translate; since less than 50% translated
and since VIR_INFO is less than VIR_WARN which also doesn't translate,
this makes sense.
* cfg.mk (sc_prohibit_gettext_markup): Add VIR_INFO, since it
falls between WARN and DEBUG.
* daemon/libvirtd.c (qemudDispatchSignalEvent, remoteCheckAccess)
(qemudDispatchServer): Adjust offenders.
* daemon/remote.c (remoteDispatchAuthPolkit): Likewise.
* src/network/bridge_driver.c (networkReloadIptablesRules)
(networkStartNetworkDaemon, networkShutdownNetworkDaemon)
(networkCreate, networkDefine, networkUndefine): Likewise.
* src/qemu/qemu_driver.c (qemudDomainDefine)
(qemudDomainUndefine): Likewise.
* src/storage/storage_driver.c (storagePoolCreate)
(storagePoolDefine, storagePoolUndefine, storagePoolStart)
(storagePoolDestroy, storagePoolDelete, storageVolumeCreateXML)
(storageVolumeCreateXMLFrom, storageVolumeDelete): Likewise.
* src/util/bridge.c (brProbeVnetHdr): Likewise.
* po/POTFILES.in: Drop src/util/bridge.c.
These VIR_XXXX0 APIs make us confused, use the non-0-suffix APIs instead.
How do these coversions works? The magic is using the gcc extension of ##.
When __VA_ARGS__ is empty, "##" will swallow the "," in "fmt," to
avoid compile error.
example: origin after CPP
high_level_api("%d", a_int) low_level_api("%d", a_int)
high_level_api("a string") low_level_api("a string")
About 400 conversions.
8 special conversions:
VIR_XXXX0("") -> VIR_XXXX("msg") (avoid empty format) 2 conversions
VIR_XXXX0(string_literal_with_%) -> VIR_XXXX(%->%%) 0 conversions
VIR_XXXX0(non_string_literal) -> VIR_XXXX("%s", non_string_literal)
(for security) 6 conversions
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
No syntactic effect; this merely silences some clang warnings.
* src/libxl/libxl_driver.c (libxlDomainSetVcpusFlags): Drop
redundant ret=0 statement.
* src/qemu/qemu_monitor_text.c (qemuMonitorTextDriveDel):
Likewise.
Introduce a virProcessKill function that can be safely called
even when the job mutex is held. This allows virDomainDestroy
to kill any VM even if it is asleep in a monitor job. The PID
will die and the thread asleep on the monitor will then wake
up releasing the job mutex.
* src/qemu/qemu_driver.c: Kill process before using qemuProcessStop
to ensure job is released
* src/qemu/qemu_process.c: Add virProcessKill for killing off
QEMU processes
This matches the public API and helps to get rid of some special
case code in the remote generator.
Rename driver API functions and XDR protocol structs.
No functional change included outside of the remote generator.
As well as taint warnings going to the main libvirt log,
add taint warnings to the per-domain logfile
Domain id=3 is tainted: high-privileges
Domain id=3 is tainted: disk-probing
Domain id=3 is tainted: shell-scripts
Domain id=3 is tainted: custom-monitor
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Enhance
qemuDomainTaint to also log to the domain logfile
* src/qemu/qemu_driver.c: Pass -1 for logFD to taint methods to
auto-append to logfile
* src/qemu/qemu_process.c: Pass open logFD at startup for taint
methods
The qemuDomainAppendLog method allows writing a formatted string
to the end of the domain logfile, optionally opening it if needed.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainAppendLog
Move the qemuProcessLogReadFD and qemuProcessLogFD methods
into qemu_domain.c, renaming them to qemuDomainCreateLog
and qemuDomainOpenLog.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainCreateLog and qemuDomainOpenLog.
* src/qemu/qemu_process.c: Remove qemuProcessLogFD
and qemuProcessLogReadFD
Wire up logging of VM tainting to the QEMU driver
- If running QEMU as root user/group or without capabilities
being cleared
- If passing custom QEMU command line args
- If issuing custom QEMU monitor commands
- If using a network interface config with an associated
shell script
- If using a disk config relying on format probing
The warnings, per-VM appear in the main libvirtd logs
11:56:17.571: 10832: warning : qemuDomainObjTaint:712 : Domain id=1 name='l2' uuid=c7a3edbd-edaf-9455-926a-d65c16db1802 is tainted: high-privileges
11:56:17.571: 10832: warning : qemuDomainObjTaint:712 : Domain id=1 name='l2' uuid=c7a3edbd-edaf-9455-926a-d65c16db1802 is tainted: disk-probing
The taint flags are reset when the VM is stopped.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Helper APIs
for logging taint warnings
* src/qemu/qemu_driver.c: Log tainting with custom QEMU monitor
commands and disk/net hotplug with unsupported configs
* src/qemu/qemu_process.c: Log tainting at startup based on
unsupported configs
We already have virAsprintf, so picking a similar name helps for
seeing a similar purpose. Furthermore, the prefix V before printf
generally implies 'va_list', even though this variant was '...', and
the old name got in the way of adding a new va_list version.
global rename performed with:
$ git grep -l virBufferVSprintf \
| xargs -L1 sed -i 's/virBufferVSprintf/virBufferAsprintf/g'
then revert the changes in ChangeLog-old.
The qemuMigrationToFile method was accidentally annotated for
the 'compressor' parameter to be non-null, instead of the
'path' parameter. Thus GCC with -O2, unhelpfully deleted the
entire 'if (compressor == NULL)' block of code during
optimization. Thus NULL was passed to virCommandNew() with
predictably bad results.
* src/qemu/qemu_migration.h: Fix non-null annotation to be
against path instead of compressor
To cope with the QEMU binary being changed while a VM is running,
it is neccessary to persist the original qemu capabilities at the
time the VM is booted.
* src/qemu/qemu_capabilities.c, src/qemu/qemu_capabilities.h: Add
an enum for a string rep of every capability
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Support for
storing capabilities in the domain status XML
* src/qemu/qemu_process.c: Populate & free QEMU capabilities at
domain startup
Clang warned about a dead assignment. In the process, I noticed
that we are only using the function for a bool value. I audited
all other callers in qemu_{migration,cgroup,driver,hotplug), and
all were making the call in a bool context.
Also, do bounds checking on the argument.
* src/qemu/qemu_cgroup.c (qemuSetupCgroup): Delete dead
assignment.
(qemuCgroupControllerActive): Change return type to bool.
* src/qemu/qemu_cgroup.h (qemuCgroupControllerActive): Likewise.
Clang 2.8 wasn't quite able to follow that persistentDef was
assigned earlier if (flags & VIR_DOMAIN_MEM_CONFIG) is true.
Silence this false positive, to make clang analysis easier to use.
* src/qemu/qemu_driver.c (qemudDomainSetMemoryFlags): Add an
annotation to silence clang's claim of a NULL dereference.
This code has had problems historically. As originally
written, in commit 6bcf2501 (Jun 08), it could call unlink
on a random string, nuking an unrelated file.
Then commit 182a80b9 (Sep 09), the code was rewritten to
allocate tmp, with both a use-after-free bug and a chance to
call unlink(NULL).
Commit e206946 (Mar 11) fixed the use-after-free, but not the
NULL dereference. Thanks to clang for catching this!
* src/qemu/qemu_driver.c (qemudDomainMemoryPeek): Don't call
unlink on NULL.
This commit fixes
qemu/qemu_driver.c: In function 'qemuDomainModifyDeviceFlags':
qemu/qemu_driver.c:4041:8: warning: 'ret' may be used uninitialized in this
function [-Wuninitialized]
qemu/qemu_driver.c:4013:9: note: 'ret' was declared here
The variable is set to -1 so that the error paths are taken when the code
to set it didn't get a chance to run. Without initializing it, we could
return some an undefined value from this function.
While I was at it, I made a trivial whitespace change in the same function
to improve readability.
Support update of disks by MODIFY_CONFIG
This patch includes changes for qemu's disk to support
virDomainUpdateDeviceFlags() with VIR_DOMAIN_DEVICE_MODIFY_CONFIG.
This patch adds support for CDROM/foppy disk types.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
* src/qemu/qemu_driver.c
(qemuDomainUpdateDeviceConfig): support cdrom/floppy.
Support changes of disks by MODIFY_CONFIG for qemu.
This patch includes patches for qemu's disk to support
virDomainAt(De)tachDeviceFlags with VIR_DOMAIN_DEVICE_MODIFY_CONFIG.
Other devices can be added incrementally.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
* /src/conf/domain_conf.c
(virDomainDiskIndexByName): returns array index of disk in vmdef.
(virDomainDiskRemoveByName): removes a disk which has the name in vmdef.
* src/qemu/qemu_driver.c
(qemuDomainAttachDeviceConfig): add support for Disks.
(qemuDomainDetachDeviceConfig): add support for Disks.
This patch adds functions for modify domain's persistent definition.
To do error recovery in easy way, we use a copy of vmdef and update it.
The whole sequence will be:
make a copy of domain definition.
if (flags & MODIFY_CONFIG)
update copied domain definition
if (flags & MODIF_LIVE)
do hotplug.
if (no error)
save copied one to the file and update cached definition.
else
discard copied definition.
This patch is mixuture of Eric Blake's work and mine.
From: Eric Blake <eblake@redhat.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
(virDomainObjCopyPersistentDef): make a copy of persistent vm definition
(qemuDomainAttach/Detach/UpdateDeviceConfig) : callbacks. now empty
(qemuDomainModifyDeviceFlags): add support for MODIFY_CONFIG and MODIFY_CURRENT
Steps to reproduce this bug:
1. # cat net.xml # 00:03.0 has been used
<interface type='network'>
<mac address='52:54:00:04:72:f3'/>
<source network='default'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/>
</interface>
2. # virsh attach-device vm1 net.xml
error: Failed to attach device from net.xml
error: internal error unable to reserve PCI address 0:0:3
3. # virsh attach-device vm1 net.xml
error: Failed to attach device from net.xml
error: internal error unable to execute QEMU command 'device_add': Device 'rtl8139' could not be initialized
The reason of this bug is that: we can not reserve PCI address 0:0:3 because it has
been used, but we release PCI address when we reserve it failed.
This patch strips reusable part of qemuDomainUpdateDeviceFlags()
and consolidate it to qemuDomainModifyDeviceFlags().
No functional changes.
* src/qemu/qemu_driver.c
(qemuDomainChangeDiskMediaLive) : pulled out code for updating disks.
(qemuDomainUpdateDeviceLive) : core of UpdateDevice, extracted from
UpdateDeviceFlags()
(qemuDomainModifyDeviceFlags): add support for updating device in live domain.
(qemuDomainUpdateDeviceFlags): reworked as a wrapper function of
qemuDomainModifyDeviceFlags()
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
clean up At(De)tachDeviceFlags() for consolidation.
qemuDomainAttachDeviceFlags()/qemuDomainDetachFlags()/
qemuDomainUpdateDeviceFlags() has similar logics and copied codes.
This patch series tries to unify them to use shared code when it can.
At first, clean up At(De)tachDeviceFlags() and devide it into functions.
By this, this patch pulls out shared components between functions.
Based on patch series by Eric Blake, I added some modification as
switch-case with QEMU_DEVICE_ATTACH, QEMU_DEVICE_DETACH, QEMU_DEVICE_UPDATE
* src/qemu/qemu_driver.c
(qemuDomainAt(De)tachDeviceFlags) : pulled out to qemuDomainModifyDeviceFlags()
(qemuDomainModifyDeviceFlags) : implements generic code for modifying domain.
(qemuDomainAt(De)tachDeviceFlagsLive) : code for at(de)taching devices to
domain in line. no changes in logic from old code.
(qemuDomainAt(De)tachDeviceDiskLive) : for at(de)taching Disks.
(qemuDomainAt(De)tachDeviceControllerLive) : for at(de)taching Controllers
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Centralize device modification in the more flexible APIs, to allow future
honoring of additional flags. Explicitly reject the
VIR_DOMAIN_DEVICE_MODIFY_FORCE flag on attach/detach.
Based on Eric Blake<eblake@redhat.com>'s work.
* src/qemu/qemu_driver.c
(qemudDomainAttachDevice)(qemudDomainAttachDeviceFlags): Swap bodies,rename...
(qemudDomainDetachDevice, qemudDomainDetachDeviceFlags): Likewise.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The two ends of the pipe used for feeding QEMU tunnelled
migration data were interchanged, so QEMU got given the
"write" end instead of the "read" end.
The qemuMigrationPrepareTunnel method was also immediately
closing the "write" end of the pipe, so the stream failed
to actually write anything.
* src/qemu/qemu_migration.c: Swap tunnelled migration
pipe FDs & don't close pipe given to stream
This last minute addition caused a build failure
cc1: warnings being treated as errors
qemu/qemu_process.c: In function 'qemuProcessHandleWatchdog':
qemu/qemu_process.c:436:34: error: ignoring return value of 'virDomainObjUnref', declared with attribute warn_unused_result [-Wunused-result]
make[3]: *** [libvirt_driver_qemu_la-qemu_process.lo] Error 1
This patch does the following two things:
1. hold an extra reference while handling watchdog event
If the domain is not persistent, and qemu quits unexpectedly before
calling processWatchdogEvent(), vm will be freed and the function
processWatchdogEvent() will be dangerous.
2. unlock qemu driver and vm before returning from processWatchdogEvent()
When the function processWatchdogEvent() failed, we only free wdEvent,
but forget to unlock qemu driver and vm, free dumpfile.
We do not lock qemu_driver when calling virThreadPoolNew(). If it failed,
we will unlock qemu_driver. It is dangerous.
We may use this pool during auto starting domains. So we must create it before
calling qemuAutostartDomains(). Otherwise, libvirtd will crash.
This patch enables the migration of Qemu VMs between hosts of different endianess. I tested this by migrating a i686 VM between a x86 and ppc64 host.
I am converting the 'int's in the VM's state header to uint32_t assuming this doesn't break compatibility with existing deployments other than Linux.
Make: passed
Make check: passed
Make syntax-check: passed
this is the commit to introduce the function to create new character
device definition for the domain as advised by Cole Robinson
<crobinso@redhat.com>.
The function is used on the relevant places and also new tests has
been added.
Signed-off-by: Michal Novotny <minovotn@redhat.com>
This extends the SPICE XML to allow variable compression settings for audio,
images and streaming:
<graphics type='spice' port='5901' tlsPort='-1' autoport='yes'>
<image compression='auto_glz'/>
<jpeg compression='auto'/>
<zlib compression='auto'/>
<playback compression='on'/>
</graphics>
All new elements are optional.
The methods qemuDomain{Get,Set}{Memory,Blkio,Scheduler}Parameters
all forgot to do a check on virDomainIsActive(), resulting in bogus
error messages from later parts of their impl
* src/qemu/qemu_driver.c: Add missing checks on virDomainIsActive()
In qemuDomainObjBeginJobWithDriver, when virCondWaitUntil timeouts,
the function tries to call qemuDriverLock with virDomainObj locked,
this causes the dead-lock problem. This patch fixes this.
This patch implements the code to support virDomainSetMaxMemory API,
and to support VIR_DOMAIN_MEM_MAXIMUM flag in qemudDomainSetMemoryFlags function.
As a result, we can change the maximum memory size of inactive QEMU guests.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
This patch adds virDomainSetMemoryFlags(,,VIR_DOMAIN_MEM_CURRENT) support
code to qemu driver.
Also, change virDomainObjIsActive to return bool, given its usage.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
1) Both "qemuDomainStartWithFlags" and "qemuAutostartDomain" try to
restore the domain from managedsave'ed image if it exists (by
invoking "qemuDomainObjRestore"), but it unlinks the image even
if restoring fails, which causes data loss. (This problem exists
for "virsh managedsave dom; virsh start dom").
The fix for is to unlink the managed state file only if restoring
succeeded.
2) For "virsh save dom; virsh restore dom;", it can cause data
corruption if one reuse the saved state file for restoring. Add
doc to tell user about it.
3) In "qemuDomainObjStart", if "managed_save" is NULL, we shouldn't
fallback to start the domain, skipping it to cleanup as a incidental
fix. Discovered by Eric.
This patch adds max_processes option to qemu.conf which can be used to
override system default limit on number of processes that are allowed to
be running for qemu user.
When initializing qemu guest capabilities, we should ignore qemu
binaries that we are not able to extract version/help info from since
they will be unusable for creating domains anyway. Ignoring them is also
much better than letting initialization of qemu driver fail.
Even with -Wuninitialized (which is part of autobuild.sh
--enable-compile-warnings=error), gcc does NOT catch this
use of an uninitialized variable:
{
if (cond)
goto error;
int a = 1;
error:
printf("%d", a);
}
which prints 0 (supposing the stack started life wiped) if
cond was true. Clang will catch it, but we don't use clang
as often. Using gcc -Wjump-misses-init catches it, but also
gives false positives:
{
if (cond)
goto error;
int a = 1;
return a;
error:
return 0;
}
Here, a was never used in the scope of the error block, so
declaring it after goto is technically fine (and clang agrees).
However, given that our HACKING already documents a preference
to C89 decl-before-statement, the false positive warning is
enough of a prod to comply with HACKING.
[Personally, I'd _really_ rather use C99 decl-after-statement
to minimize scope, but until gcc can efficiently and reliably
catch scoping and uninitialized usage bugs, I'll settle with
the compromise of enforcing a coding standard that happens to
reject false positives if it can also detect real bugs.]
* acinclude.m4 (LIBVIRT_COMPILE_WARNINGS): Add -Wjump-misses-init.
* src/util/util.c (__virExec): Adjust offenders.
* src/conf/domain_conf.c (virDomainTimerDefParseXML): Likewise.
* src/remote/remote_driver.c (doRemoteOpen): Likewise.
* src/phyp/phyp_driver.c (phypGetLparNAME, phypGetLparProfile)
(phypGetVIOSFreeSCSIAdapter, phypVolumeGetKey)
(phypGetStoragePoolDevice)
(phypVolumeGetPhysicalVolumeByStoragePool)
(phypVolumeGetPath): Likewise.
* src/vbox/vbox_tmpl.c (vboxNetworkUndefineDestroy)
(vboxNetworkCreate, vboxNetworkDumpXML)
(vboxNetworkDefineCreateXML): Likewise.
* src/xenapi/xenapi_driver.c (getCapsObject)
(xenapiDomainDumpXML): Likewise.
* src/xenapi/xenapi_utils.c (createVMRecordFromXml): Likewise.
* src/security/security_selinux.c (SELinuxGenNewContext):
Likewise.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Likewise.
* src/qemu/qemu_hotplug.c (qemuDomainChangeEjectableMedia):
Likewise.
* src/qemu/qemu_process.c (qemuProcessWaitForMonitor): Likewise.
* src/qemu/qemu_monitor_text.c (qemuMonitorTextGetPtyPaths):
Likewise.
* src/qemu/qemu_driver.c (qemudDomainShutdown)
(qemudDomainBlockStats, qemudDomainMemoryPeek): Likewise.
* src/storage/storage_backend_iscsi.c
(virStorageBackendCreateIfaceIQN): Likewise.
* src/node_device/node_device_udev.c (udevProcessPCI): Likewise.
If strdup("x509dname") or strdup("saslUsername") success, but
strdup(x509dname) or strdup(saslUsername) failed, subject->nidentity
is not the num elements of subject->identities, and we will leak some
memory.
qemu driver uses a 4K buffer for reading qemu log file. This is enough
when only qemu's output is present in the log file. However, when
debugging messages are turned on, intermediate libvirt process fills the
log with a bunch of debugging messages before it executes qemu binary.
In such a case the buffer may become too small. However, we are not
really interested in libvirt messages so they can be filtered out from
the buffer.
It throws errors as long as the cgroup controller is not available,
regardless of whether we really want to use it to do setup or not,
which is not what we want, fixing it with throwing error when need
to use the controller.
And change "VIR_WARN" to "qemuReportError" for memory controller
incidentally.
We create a temporary file to save memory, and we will remove it after reading
memory to buffer. But we free the variable that contains the temporary filename
before we remove it. So we should free tmp after unlinking it.
strcase{cmp/str} have the drawback of being sensitive to the global
locale; this is unacceptable in a library setting. Prefer a
hard-coded C locale alternative for all but virsh, which is user
facing and where the global locale isn't changing externally.
* .gnulib: Update to latest, for c-strcasestr change.
* bootstrap.conf (gnulib_modules): Drop strcasestr, add c-strcase
and c-strcasestr.
* cfg.mk (sc_avoid_strcase): New rule.
(exclude_file_name_regexp--sc_avoid_strcase): New exception.
* src/internal.h (STRCASEEQ, STRCASENEQ, STRCASEEQLEN)
(STRCASENEQLEN): Adjust offenders.
* src/qemu/qemu_monitor_text.c (qemuMonitorTextEjectMedia):
Likewise.
* tools/virsh.c (namesorter): Document exception.
If qemu quited unexpectedly when we call qemuMonitorJSONHMP(),
libvirt will crash.
Steps to reproduce this bug:
1. use gdb to attach libvirtd, and set a breakpoint in the function
qemuMonitorSetCapabilities()
2. start a vm
3. let the libvirtd to run until qemuMonitorJSONSetCapabilities() returns.
4. kill the qemu process
5. continue running libvirtd
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
If the monitor met a error, and we will call qemuProcessHandleMonitorEOF().
But we may try to send monitor command after qemuProcessHandleMonitorEOF()
returned. Then libvirtd will be blocked in qemuMonitorSend().
Steps to reproduce this bug:
1. use gdb to attach libvirtd, and set a breakpoint in the function
qemuConnectMonitor()
2. start a vm
3. let the libvirtd to run until qemuMonitorOpen() returns.
4. kill the qemu process
5. continue running libvirtd
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Currently libvirt's default logging is limited and it is difficult to
determine what was happening when a proglem occurred (especially on a
machines where one don't know the detail.) This patch helps to do that
by making additional logging available for the following events:
creating/defining/undefining domains
creating/defining/undefining/starting/stopping networks
creating/defining/undefining/starting/stopping storage pools
creating/defining/undefining/starting/stopping storage volumes.
* AUTHORS: add Naoya Horiguchi
* src/network/bridge_driver.c src/qemu/qemu_driver.c
src/storage/storage_driver.c: provide more VIR_INFO logging
When domain startup, setting cpu affinity and cpu shares according
to the cputune xml specified in domain xml.
Modify "qemudDomainPinVcpu" to update domain config for vcpupin,
and modify "qemuSetSchedulerParameters" to update domain config
for cpu shares.
v1 - v2:
* Use "VIR_ALLOC_N" instead of "VIR_ALLOC_VAR"
* But keep raising error when it fails on adding vcpupin xml
entry, as I still don't have a better idea yet.
My earlier testing for commit 34fa0de0 was done while starting
just-built libvirt from an unconfined_t shell, where the fds happened
to work when transferring to qemu. But when installed and run under
virtd_t, failure to label the raw file (with no compression) or the
pipe (with compression) triggers SELinux failures when passing fds
over SCM_RIGHTS to svirt_t qemu.
* src/qemu/qemu_migration.c (qemuMigrationToFile): When passing
FDs, make sure they are labeled.
First fallout of fd: migration - it looks like SELinux enforcing
_does_ require fd labeling (running uninstalled libvirtd from an
unconstrained shell had no problems, but once faked out by doing
chcon `stat -c %C /usr/sbin/libvirtd` daemon/libvirtd
run_init $PWD/daemon/libvirtd
to run it with the same context as an init script service, and with
SELinux enforcing, I got a rather confusing failure:
error: Failed to save domain fedora_12 to fed12.img
error: internal error unable to send TAP file handle: No file descriptor supplied via SCM_RIGHTS
This fixes the error message, then I need to figure out a subsequent
patch that does the fsetfilecon() necessary to keep things happy.
It also appears that libvirtd hangs on a failed fd transfer; I don't
know if that needs an independent fix.
* src/qemu/qemu_monitor_text.c (qemuMonitorTextSendFileHandle):
Improve message, since TAP is no longer only client.
The O_NONBLOCK flag doesn't work as desired on plain files
or block devices. Introduce an I/O helper program that does
the blocking I/O operations, communicating over a pipe that
can support O_NONBLOCK
* src/fdstream.c, src/fdstream.h: Add non-blocking I/O
on plain files/block devices
* src/Makefile.am, src/util/iohelper.c: I/O helper program
* src/qemu/qemu_driver.c, src/lxc/lxc_driver.c,
src/uml/uml_driver.c, src/xen/xen_driver.c: Update for
streams API change
Spawn the compressor ourselves, instead of requiring the shell.
* src/qemu/qemu_migration.c (qemuMigrationToFile): Spawn
compression helper process when needed.
SELinux labeling and cgroup ACLs aren't required if we hand a
pre-opened fd to qemu. All the more reason to love fd: migration.
* src/qemu/qemu_migration.c (qemuMigrationToFile): Skip steps
that are irrelevant in fd migration.
This points out that core dumps (still) don't work for root-squash
NFS, since the fd is not opened correctly. This patch should not
introduce any functionality change, it is just a refactoring to
avoid duplicated code.
* src/qemu/qemu_migration.h (qemuMigrationToFile): New prototype.
* src/qemu/qemu_migration.c (qemuMigrationToFile): New function.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag, doCoreDump): Use
it.
Direct access to an open file is so much simpler than passing
everything through a pipe!
* src/qemu/qemu_driver.c (qemudOpenAsUID)
(qemudDomainSaveImageClose): Delete.
(qemudDomainSaveImageOpen): Rename...
(qemuDomainSaveImageOpen): ...and drop read_pid argument. Use
virFileOpenAs instead of qemudOpenAsUID.
(qemudDomainSaveImageStartVM, qemudDomainRestore)
(qemudDomainObjRestore): Rename...
(qemuDomainSaveImageStartVM, qemuDomainRestore)
(qemDomainObjRestore): ...and simplify accordingly.
(qemudDomainObjStart, qemuDriver): Update callers.
This patch intentionally doesn't change indentation, in order to
make it easier to review the real changes.
* src/util/util.h (VIR_FILE_OP_RETURN_FD, virFileOperationHook):
Delete.
(virFileOperation): Rename...
(virFileOpenAs): ...and reduce parameters.
* src/util/util.c (virFileOperationNoFork, virFileOperation):
Rename and simplify.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Adjust caller.
* src/storage/storage_backend.c (virStorageBackendCreateRaw):
Likewise.
* src/libvirt_private.syms: Reflect rename.
This allows direct saves (no compression, no root-squash NFS) to use
the more efficient fd: migration, which in turn avoids a race where
qemu exec: migration can sometimes fail because qemu does a generic
waitpid() that conflicts with the pclose() used by exec:. Further
patches will solve compression and root-squash NFS.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Use new function
when there is no compression.
Latent bug introduced in commit 2d6a581960 (Aug 2009), but not exposed
until commit 1859939a (Jan 2011). Basically, when virExec creates a
pipe, it always marks libvirt's side as cloexec. If libvirt then
wants to hand that pipe to another child process, things work great if
the fd is dup2()'d onto stdin or stdout (as with stdin: or exec:
migration), but if the pipe is instead used as-is (such as with fd:
migration) then qemu sees EBADF because the fd was closed at exec().
This is a minimal fix for the problem at hand; it is slightly racy,
but no more racy than the rest of libvirt fd handling, including the
case of uncompressed save images. A more invasive fix, but ultimately
safer at avoiding leaking unintended fds, would be to _always and
atomically_ open all fds as cloexec in libvirt (thanks to primitives
like open(O_CLOEXEC), pipe2(), accept4(), ...), then teach virExec to
clear that bit for all fds explicitly marked to be handed to the child
only after forking.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Clear cloexec
flag.
* tests/qemuxml2argvtest.c (testCompareXMLToArgvFiles): Tweak test.
Otherwise, if something like doStopVcpus fails after the first
restore, a second restore is attempted and throws a useless
warning.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Avoid second
restore of state label.
Add missing open curly brace between function declaration of non-linux
variant of qemudDomainInterfaceStats() and its body.
Signed-off-by: Philipp Hahn <hahn@univention.de>
Hotpluging host usb device by text mode will fail, because the monitor
command 'device_add' outputs 'husb: using...' if it succeeds, but we
think the command should not output anything.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Add the compiler attribute to ensure we don't introduce any more
ref bugs like were just patched in commit 9741f34, then explicitly
mark the remaining places in code that are safe.
* src/qemu/qemu_monitor.h (qemuMonitorUnref): Mark
ATTRIBUTE_RETURN_CHECK.
* src/conf/domain_conf.h (virDomainObjUnref): Likewise.
* src/conf/domain_conf.c (virDomainObjParseXML)
(virDomainLoadStatus): Fix offenders.
* src/openvz/openvz_conf.c (openvzLoadDomains): Likewise.
* src/vmware/vmware_conf.c (vmwareLoadDomains): Likewise.
* src/qemu/qemu_domain.c (qemuDomainObjBeginJob)
(qemuDomainObjBeginJobWithDriver)
(qemuDomainObjExitRemoteWithDriver): Likewise.
* src/qemu/qemu_monitor.c (QEMU_MONITOR_CALLBACK): Likewise.
Suggested by Daniel P. Berrange.
This simplifies several callers that were repeating checks already
guaranteed by util.c, and makes other callers more robust to now
reject directories. remote_driver.c was over-strict - access(,R_OK)
is only needed to execute a script file; a binary only needs
access(,X_OK) (besides, it's unusual to see a file with x but not
r permissions, whether script or binary).
* cfg.mk (sc_prohibit_access_xok): New syntax-check rule.
(exclude_file_name_regexp--sc_prohibit_access_xok): Exempt one use.
* src/network/bridge_driver.c (networkStartRadvd): Fix offenders.
* src/qemu/qemu_capabilities.c (qemuCapsProbeMachineTypes)
(qemuCapsInitGuest, qemuCapsInit, qemuCapsExtractVersionInfo):
Likewise.
* src/remote/remote_driver.c (remoteFindDaemonPath): Likewise.
* src/uml/uml_driver.c (umlStartVMDaemon): Likewise.
* src/util/hooks.c (virHookCheck): Likewise.
Steps to reproduce this bug:
1. virsh attach-disk domain --source diskimage --target sdb --sourcetype file --driver qemu --subdriver qcow2
error: Failed to attach disk
error: operation failed: adding scsi-disk,bus=scsi0.0,scsi-id=1,drive=drive-scsi0-0-1,id=scsi0-0-1 device failed: Property 'scsi-disk.drive' can't find value 'drive-scsi0-0-1'
2. service libvirtd restart
Stopping libvirtd daemon: [ OK ]
Starting libvirtd daemon: [ OK ]
3. virsh attach-disk domain --source diskimage --target sdb --sourcetype file --driver qemu --subdriver raw
error: Failed to attach disk
error: operation failed: adding lsi,id=scsi0,bus=pci.0,addr=0x6 device failed: Duplicate ID 'scsi0' for device
The reason is that we create a new scsi controller but we do not update
/var/run/libvirt/qemu/domain.xml.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Steps to reproduce this bug:
# cat usb.xml
<hostdev mode='subsystem' type='usb'>
<source>
<address bus='0x001' device='0x003'/>
</source>
</hostdev>
# virsh attach-device vm1 usb.xml
error: Failed to attach device from usb.xml
error: server closed connection:
The reason of this bug is that we set data.cgroup to NULL, and this will cause
libvirtd crashed.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
A future patch will change reference counting idioms; consolidating
this pattern now makes the next patch smaller (touch only the new
macro rather than every caller).
* src/qemu/qemu_monitor.c (QEMU_MONITOR_CALLBACK): New helper.
(qemuMonitorGetDiskSecret, qemuMonitorEmitShutdown)
(qemuMonitorEmitReset, qemuMonitorEmitPowerdown)
(qemuMonitorEmitStop, qemuMonitorEmitRTCChange)
(qemuMonitorEmitWatchdog, qemuMonitorEmitIOError)
(qemuMonitorEmitGraphics): Use it to reduce duplication.
Enhance the QEMU migration monitoring loop, so that it can get
a signal to change migration speed on the fly
* src/qemu/qemu_domain.h: Add signal for changing speed on the fly
* src/qemu/qemu_driver.c: Wire up virDomainMigrateSetSpeed driver
* src/qemu/qemu_migration.c: Support signal for changing speed
It is possible to set a migration speed limit when starting
migration. This new API allows the speed limit to be changed
on the fly to adjust to changing conditions
* src/driver.h, src/libvirt.c, src/libvirt_public.syms,
include/libvirt/libvirt.h.in: Add virDomainMigrateSetMaxSpeed
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/vmware/vmware_driver.c, src/xen/xen_driver.c,
src/libxl/libxl_driver.c: Stub new API
Fix for bug https://bugzilla.redhat.com/show_bug.cgi?id=618970
The "prepare" hook is called very early in the VM statup process
before device labeling, so that it can allocate ressources not
managed by libvirt, such as DRBD, or for instance create missing
bridges and vlan interfaces.
* src/util/hooks.c src/util/hooks.h: add definitions for new hooks
VIR_HOOK_QEMU_OP_PREPARE and VIR_HOOK_QEMU_OP_RELEASE
* src/qemu/qemu_process.c: use them in qemuProcessStart and
qemuProcessStop()
With only a single caller to these two monitor commands, I
didn't need to wrap a new WithFds version, but just change
the command itself.
* src/qemu/qemu_monitor.h (qemuMonitorAddNetdev)
(qemuMonitorAddHostNetwork): Add parameters.
* src/qemu/qemu_monitor.c (qemuMonitorAddNetdev)
(qemuMonitorAddHostNetwork): Add support for fd passing.
* src/qemu/qemu_hotplug.c (qemuDomainAttachNetDevice): Use it to
simplify code.
This is also a bug fix - on the error path, qemu_hotplug would
leave the configfd file leaked into qemu. At least the next
attempt to hotplug a PCI device would reuse the same fdname,
and when the qemu getfd monitor command gets a new fd by the
same name as an earlier one, it closes the earlier one, so there
is no risk of qemu running out of fds.
* src/qemu/qemu_monitor.h (qemuMonitorAddDeviceWithFd): New
prototype.
* src/qemu/qemu_monitor.c (qemuMonitorAddDevice): Move guts...
(qemuMonitorAddDeviceWithFd): ...to new function, and add support
for fd passing.
* src/qemu/qemu_hotplug.c (qemuDomainAttachHostPciDevice): Use it
to simplify code.
Suggested by Daniel P. Berrange.
qemu_monitor was already returning -1 and setting errno to EINVAL
on any attempt to send an fd without a unix socket, but this was
a silent failure in the case of qemuDomainAttachHostPciDevice.
Meanwhile, qemuDomainAttachNetDevice was doing some sanity checking
for a better error message; it's better to consolidate that to a
central point in the API.
* src/qemu/qemu_hotplug.c (qemuDomainAttachNetDevice): Move sanity
checking...
* src/qemu/qemu_monitor.c (qemuMonitorSendFileHandle): ...into
central location.
Suggested by Chris Wright.
THREADS.txt states that the contents of vm should not be read or
modified while the vm lock is not held, but that the lock must not
be held while performing a monitor command. This fixes all the
offenders that I could find.
* src/qemu/qemu_process.c (qemuProcessStartCPUs)
(qemuProcessInitPasswords, qemuProcessStart): Don't modify or
refer to vm state outside lock.
* src/qemu/qemu_driver.c (qemudDomainHotplugVcpus): Likewise.
* src/qemu/qemu_hotplug.c (qemuDomainChangeGraphicsPasswords):
Likewise.
Steps to reproduce this bug:
# cat test.sh
#! /bin/bash -x
virsh start domain
sleep 5
virsh qemu-monitor-command domain 'cpu_set 2 online' --hmp
# while true; do ./test.sh ; done
Then libvirtd will crash.
The reason is that:
we add a reference of obj when we open the monitor. We will reduce this
reference when we free the monitor.
If the reference of monitor is 0, we will free monitor automatically and
the reference of obj is reduced.
But in the function qemuDomainObjExitMonitorWithDriver(), we reduce this
reference again when the reference of monitor is 0.
It will cause the obj be freed in the function qemuDomainObjEndJob().
Then we start the domain again, and libvirtd will crash in the function
virDomainObjListSearchName(), because we pass a null pointer(obj->def->name)
to strcmp().
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
This bug was reported by Shi Jin(jinzishuai@gmail.com):
=============
# virsh attach-disk RHEL6RC /var/lib/libvirt/images/test3.img vdb \
--driver file --subdriver qcow2
Disk attached successfully
# virsh save RHEL6RC /var/lib/libvirt/images/memory.save
Domain RHEL6RC saved to /var/lib/libvirt/images/memory.save
# virsh restore /var/lib/libvirt/images/memory.save
error: Failed to restore domain from /var/lib/libvirt/images/memory.save
error: internal error unsupported driver name 'file'
for disk '/var/lib/libvirt/images/test3.img'
=============
We check the driver name when we start or restore VM, but we do
not check it while attaching a disk. This adds the same check on disk
driverName used in qemuBuildCommandLine to qemudDomainAttachDevice.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Steps to reproduce this bug:
# virsh qemu-monitor-command domain 'cpu_set 2 online' --hmp
The domain has 2 cpus, and we try to set the third cpu online.
The qemu crashes, and this command will hang.
The reason is that the refs is not 1 when we unwatch the monitor.
We lock the monitor, but we do not unlock it. So virCondWait()
will be blocked.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
* Correct the documentation for cgroup: the swap_hard_limit indicates
mem+swap_hard_limit.
* Change cgroup private apis to: virCgroupGet/SetMemSwapHardLimit
Signed-off-by: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
POSIX states about dd:
If the bs=expr operand is specified and no conversions other than
sync, noerror, or notrunc are requested, the data returned from each
input block shall be written as a separate output block; if the read
returns less than a full block and the sync conversion is not
specified, the resulting output block shall be the same size as the
input block. If the bs=expr operand is not specified, or a conversion
other than sync, noerror, or notrunc is requested, the input shall be
processed and collected into full-sized output blocks until the end of
the input is reached.
Since we aren't using conv=sync, there is no zero-padding, but our
use of bs= means that a short read results in a short write. If
instead we use ibs= and obs=, then short reads are collected and dd
only has to do a single write, which can make dd more efficient.
* src/qemu/qemu_monitor.c (qemuMonitorMigrateToFile):
Avoid 'dd bs=', since it can cause short writes.
Outgoing migration still uses a Unix socket and or exec netcat until
the next patch.
* src/qemu/qemu_migration.c (qemuMigrationPrepareTunnel):
Replace Unix socket with simpler pipe.
Suggested by Paolo Bonzini.
The newly added call to qemuAuditNetDevice in qemuPhysIfaceConnect was
assuming that res_ifname (the name of the macvtap device) was always
valid, but this isn't the case. If openMacvtapTap fails, it always
returns NULL, which would result in a segv.
Since the audit log only needs a record of devices that are actually
sent to qemu, and a failure to open the macvtap device means that no
device will be sent to qemu, we can solve this problem by only doing
the audit if openMacvtapTap is successful (in which case res_ifname is
guaranteed valid).
This patch introduces a new libvirt API (virDomainSetMemoryFlags) and
a flag (virDomainMemoryModFlags).
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Opening raw network devices with the intent of passing those fds to
qemu is worth an audit point. This makes a multi-part audit: first,
we audit the device(s) that libvirt opens on behalf of the MAC address
of a to-be-created interface (which can independently succeed or
fail), then we audit whether qemu actually started the network device
with the same MAC (so searching backwards for successful audits with
the same MAC will show which fd(s) qemu is actually using). Note that
it is possible for the fd to be successfully opened but no attempt
made to pass the fd to qemu (for example, because intermediate
nwfilter operations failed) - no interface start audit will occur in
that case; so the audit for a successful opened fd does not imply
rights given to qemu unless there is a followup audit about the
attempt to start a new interface.
Likewise, when a network device is hot-unplugged, there is only one
audit message about the MAC being discontinued; again, searching back
to the earlier device open audits will show which fds that qemu quits
using (and yes, I checked via /proc/<qemu-pid>/fd that qemu _does_
close out the fds associated with an interface on hot-unplug). The
code would require much more refactoring to be able to definitively
state which device(s) were discontinued at that point, since we
currently don't record anywhere in the XML whether /dev/vhost-net was
opened for a given interface.
* src/qemu/qemu_audit.h (qemuAuditNetDevice): New prototype.
* src/qemu/qemu_audit.c (qemuAuditNetDevice): New function.
* src/qemu/qemu_command.h (qemuNetworkIfaceConnect)
(qemuPhysIfaceConnect, qemuOpenVhostNet): Adjust prototype.
* src/qemu/qemu_command.c (qemuNetworkIfaceConnect)
(qemuPhysIfaceConnect, qemuOpenVhostNet): Add audit points and
adjust parameters.
(qemuBuildCommandLine): Adjust caller.
* src/qemu/qemu_hotplug.c (qemuDomainAttachNetDevice): Likewise.
Since libvirt always passes /dev/net/tun to qemu via fd, we should
never trigger the cases where qemu tries to directly open the
device. Therefore, it is safer to deny the cgroup device ACL.
* src/qemu/qemu_cgroup.c (defaultDeviceACL): Remove /dev/net/tun.
* src/qemu/qemu.conf (cgroup_device_acl): Reflect this change.
qemu driver in libvirt gained support for creating domain snapshots
almost a year ago in libvirt 0.8.0. Since then we enabled QMP support
for qemu >= 0.13.0 but QMP equivalents of {save,load,del}vm commands are
not implemented in current qemu (0.14.0) so the domain snapshot support
is not very useful.
This patch detects when the appropriate QMP command is not implemented
and tries to use human-monitor-command (aka HMP passthrough) to run
it's HMP equivalent.
JSON monitor command implementation can now just directly call text
monitor implementation and it will be automatically encapsulated into
QMP's human-monitor-command.
Some qemu monitor event handlers were issuing inadequate warning when
virDomainSaveStatus() failed. They copied the message from I/O error
handler without customizing it to provide better information on why
virDomainSaveStatus() was called.
Adding audit points showed that we were granting too much privilege
to qemu; it should not need any mknod rights to recreate any
devices. On the other hand, lxc should have all device privileges.
The solution is adding a flag parameter.
This also lets us restrict write access to read-only disks.
* src/util/cgroup.h (virCgroup*Device*): Adjust prototypes.
* src/util/cgroup.c (virCgroupAllowDevice)
(virCgroupAllowDeviceMajor, virCgroupAllowDevicePath)
(virCgroupDenyDevice, virCgroupDenyDeviceMajor)
(virCgroupDenyDevicePath): Add parameter.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Update clients.
* src/lxc/lxc_controller.c (lxcSetContainerResources): Likewise.
* src/qemu/qemu_cgroup.c: Likewise.
(qemuSetupDiskPathAllow): Also, honor read-only disks.
Although the cgroup device ACL controller path can be worked out
by researching the code, it is more efficient to include that
information directly in the audit message.
* src/util/cgroup.h (virCgroupPathOfController): New prototype.
* src/util/cgroup.c (virCgroupPathOfController): Export.
* src/libvirt_private.syms: Likewise.
* src/qemu/qemu_audit.c (qemuAuditCgroup): Use it.
Device names can be manipulated, so it is better to also log
the major/minor device number corresponding to the cgroup ACL
changes that libvirt made. This required some refactoring
of the relatively new qemu cgroup audit code.
Also, qemuSetupChardevCgroup was only auditing on failure, not success.
* src/qemu/qemu_audit.h (qemuDomainCgroupAudit): Delete.
(qemuAuditCgroup, qemuAuditCgroupMajor, qemuAuditCgroupPath): New
prototypes.
* src/qemu/qemu_audit.c (qemuDomainCgroupAudit): Rename...
(qemuAuditCgroup): ...and drop a parameter.
(qemuAuditCgroupMajor, qemuAuditCgroupPath): New functions, to
allow listing device major/minor in audit.
(qemuAuditGetRdev): New helper function.
* src/qemu/qemu_driver.c (qemudDomainSaveFlag): Adjust callers.
* src/qemu/qemu_cgroup.c (qemuSetupDiskPathAllow)
(qemuSetupHostUsbDeviceCgroup, qemuSetupCgroup)
(qemuTeardownDiskPathDeny): Likewise.
(qemuSetupChardevCgroup): Likewise, fixing missing audit.
* src/qemu/qemu_audit.c (qemuDomainHostdevAudit): Avoid use of
"type", which has a pre-defined meaning.
(qemuDomainCgroupAudit): Likewise, as well as "item".
virRun gives pretty useful error output, let's not overwrite it unless there
is a good reason. Some places were providing more information about what
the commands were _attempting_ to do, however that's usually less useful from
a debugging POV than what actually happened.
The way to detach a USB disk is the same as that to detach a SCSI
disk. Rename this function and we can use it to detach a USB disk.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
For qemu names the primary vga as "qxl-vga":
1) if vram is specified for 2nd qxl device:
-vga qxl -global qxl-vga.vram_size=$SIZE \
-device qxl,id=video1,vram_size=$SIZE,...
2) if vram is not specified for 2nd qxl device, (use the default
set by global):
-vga qxl -global qxl-vga.vram_size=$SIZE \
-device qxl,id=video1,...
For qemu names all qxl devices as "qxl":
1) if vram is specified for 2nd qxl device:
-vga qxl -global qxl.vram_size=$SIZE \
-device qxl,id=video1,vram_size=$SIZE ...
2) if vram is not specified for 2nd qxl device:
-vga qxl -global qxl-vga.vram_size=$SIZE \
-device qxl,id=video1,...
"-global" is the only way to define vram_size for the primary qxl
device, regardless of how qemu names it, (It's not good a good
way, as original idea of "-global" is to set a global default for
a driver property, but to specify vram for first qxl device, we
have to use it).
For other qxl devices, as they are represented by "-device", could
specify it directly and seperately for each, and it overrides the
default set by "-global" if specified.
v1 - v2:
* modify "virDomainVideoDefaultRAM" so that it returns 16M as the
default vram_size for qxl device.
* vram_size * 1024 (qemu accepts bytes for vram_size).
* apply default vram_size for qxl device for which vram_size is
not specified.
* modify "graphics-spice" tests (more sensiable vram_size)
* Add an argument of virDomainDefPtr type for qemuBuildVideoDevStr,
to use virDomainVideoDefaultRAM in qemuBuildVideoDevStr).
v2 - v3:
* Modify default video memory size for qxl device from 16M to 24M
* Update codes to be consistent with changes on qemu_capabilities.*
This was also found while investigating
https://bugzilla.redhat.com/show_bug.cgi?id=670848
An EOF on a domain's monitor socket results in an event being queued
to handle the EOF. The handler calls qemuProcessHandleMonitorEOF. If
it is a transient domain, this leads to a call to
virDomainRemoveInactive, which removes the domain from the driver's
hashtable and unref's it. Nowhere in this code is the qemu driver lock
acquired.
However, all modifications to the driver's domain hashtable *must* be
done while holding the driver lock, otherwise the hashtable can become
corrupt, and (even more likely) another thread could call a different
hashtable function and acquire a pointer to the domain that is in the
process of being destroyed.
To prevent such a disaster, qemuProcessHandleMonitorEOF must get the
qemu driver lock *before* it gets the DomainObj's lock, and hold it
until it is finished with the DomainObj. This guarantees that nobody
else modifies the hashtable at the same time, and that anyone who had
already gotten the DomainObj from the hashtable prior to this call has
finished with it before we remove/destroy it.
This was found while researching the root cause of:
https://bugzilla.redhat.com/show_bug.cgi?id=670848
virDomainUnref should only be called with the lock held for the
virDomainObj in question. However, when a transient qemu domain gets
EOF on its monitor socket, it queues an event which frees the monitor,
which unref's the virDomainObj without first locking it. If another
thread has already locked the virDomainObj, the modification of the
refcount could potentially be corrupted. In an extreme case, it could
also be potentially unlocked by virDomainObjFree, thus left open to
modification by anyone else who would have otherwise waited for the
lock (not to mention the fact that they would be accessing freed
data!).
The solution is to have qemuMonitorFree lock the domain object right
before unrefing it. Since the caller to qemuMonitorFree doesn't expect
this lock to be held, if the refcount doesn't go all the way to 0,
qemuMonitorFree must unlock it after the unref.
qemudDomainSaveImageStartVM was evil - it closed the incoming fd
argument on some, but not all, code paths, without informing the
caller about that action. No wonder that this resulted in
double-closes: https://bugzilla.redhat.com/show_bug.cgi?id=672725
* src/qemu/qemu_driver.c (qemudDomainSaveImageStartVM): Alter
signature, to avoid double-close.
(qemudDomainRestore, qemudDomainObjRestore): Update callers.
When a SPICE or VNC graphics controller is present, and sound is
piggybacked over a channel to the graphics device rather than
directly accessing host hardware, then there is no need to grant
host hardware access to that qemu process.
* src/qemu/qemu_cgroup.c (qemuSetupCgroup): Prevent sound with
spice, and with vnc when vnc_allow_host_audio is 0.
Reported by Daniel Berrange.
Relax the restriction that the hash table key must be a string
by allowing an arbitrary hash code generator + comparison func
to be provided
* util/hash.c, util/hash.h: Allow any pointer as a key
* internal.h: Include stdbool.h as standard.
* conf/domain_conf.c, conf/domain_conf.c,
conf/nwfilter_params.c, nwfilter/nwfilter_gentech_driver.c,
nwfilter/nwfilter_gentech_driver.h, nwfilter/nwfilter_learnipaddr.c,
qemu/qemu_command.c, qemu/qemu_driver.c,
qemu/qemu_process.c, uml/uml_driver.c,
xen/xm_internal.c: s/char */void */ in hash callbacks
Since the deallocator is passed into the constructor of
a hash table it is not desirable to pass it into each
function again. Remove it from all functions, but provide
a virHashSteal to allow a item to be removed from a hash
table without deleteing it.
* src/util/hash.c, src/util/hash.h: Remove deallocator
param from all functions. Add virHashSteal
* src/libvirt_private.syms: Add virHashSteal
* src/conf/domain_conf.c, src/conf/nwfilter_params.c,
src/nwfilter/nwfilter_learnipaddr.c,
src/qemu/qemu_command.c, src/xen/xm_internal.c: Update
for changed hash API
This is done for two reasons:
- we are getting very close to 64 flags which is the maximum we can use
with unsigned long long
- by using LL constants in enum we already violates C99 constraint that
enum values have to fit into int
Steps to reproduce this bug:
1. virsh attach-disk domain --source imagefile --target sdb --sourcetype file --driver qemu --subdriver raw
2. virsh detach-device controller.xml # remove scsi controller 0
3. virsh detach-disk domain sdb
error: Failed to detach disk
error: operation failed: detaching scsi0-0-1 device failed: Device 'scsi0-0-1' not found
I think we should not detach a controller when it is used by some other device.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Done mechanically with:
$ git grep -l '\bDEBUG0\? *(' | xargs -L1 sed -i 's/\bDEBUG0\? *(/VIR_&/'
followed by manual deletion of qemudDebug in daemon/libvirtd.c, along
with a single 'make syntax-check' fallout in the same file, and the
actual deletion in src/util/logging.h.
* src/util/logging.h (DEBUG, DEBUG0): Delete.
* daemon/libvirtd.h (qemudDebug): Likewise.
* global: Change remaining clients over to VIR_DEBUG counterpart.
Now that the virHash handling functions call virReportOOMError by
themselves when needed, users of the virHash API no longer need to
do it by themselves. Since users of the virHash API were not
consistently calling virReportOOMError after memory failures from
the virHash code, this has the added benefit of making OOM
reporting from this code more consistent and reliable.
When we attach a disk, but we specify a wrong format of disk image,
qemu monitor command drive_add will fail, but libvirt does not detect
this error.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
An upcoming patch has a use for a tap device to be created that
doesn't need to be actually put into the "up" state, and keeping it
"down" keeps the output of ifconfig from being unnecessarily cluttered
(ifconfig won't show down interfaces unless you add "-a").
bridge.[ch]: add "up" as an arg to brAddTap()
uml_conf.c, qemu_command.c: add "up" (set to "true") to brAddTap() call.
This is in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=629662
Explanation
qemu's virtio-net-pci driver allows setting the algorithm used for tx
packets to either "bh" or "timer". This is done by adding ",tx=bh" or
",tx=timer" to the "-device virtio-net-pci" commandline option.
'bh' stands for 'bottom half'; when this is set, packet tx is all done
in an iothread in the bottom half of the driver. (In libvirt, this
option is called the more descriptive "iothread".)
'timer' means that tx work is done in qemu, and if there is more tx
data than can be sent at the present time, a timer is set before qemu
moves on to do other things; when the timer fires, another attempt is
made to send more data. (libvirt retains the name "timer" for this
option.)
The resulting difference, according to the qemu developer who added
the option is:
bh makes tx more asynchronous and reduces latency, but potentially
causes more processor bandwidth contention since the cpu doing the
tx isn't necessarily the cpu where the guest generated the
packets.
Solution
This patch provides a libvirt domain xml knob to change the option on
the qemu commandline, by adding a new attribute "txmode" to the
<driver> element that can be placed inside any <interface> element in
a domain definition. It's use would be something like this:
<interface ...>
...
<model type='virtio'/>
<driver txmode='iothread'/>
...
</interface>
I chose to put this setting as an attribute to <driver> rather than as
a sub-element to <tune> because it is specific to the virtio-net
driver, not something that is generally usable by all network drivers.
(note that this is the same placement as the "driver name=..."
attribute used to choose kernel vs. userland backend for the
virtio-net driver.)
Actually adding the tx=xxx option to the qemu commandline is only done
if the version of qemu being used advertises it in the output of
qemu -device virtio-net-pci,?
If a particular txmode is requested in the XML, and the option isn't
listed in that help output, an UNSUPPORTED_CONFIG error is logged, and
the domain fails to start.
When the <driver> element (and its "name" attribute) was added to the
domain XML's interface element, a "backend" enum was simply added to
the toplevel of the virDomainNetDef struct.
Ignoring the naming inconsistency ("name" vs. "backend"), this is fine
when there's only a single item contained in the driver element of the
XML, but doesn't scale well as we add more attributes that apply to
the backend of the virtio-net driver, or add attributes applicable to
other drivers.
This patch changes virDomainNetDef in two ways:
1) Rename the item in the struct from "backend" to "name", so that
it's the same in the XML and in the struct, hopefully avoiding
confusion for someone unfamiliar with the function of the
attribute.
2) Create a "driver" union within virDomainNetDef, and a "virtio"
struct in that struct, which contains the "name" enum value.
3) Move around the virDomainNetParse and virDomainNetFormat functions
to allow for simple plugin of new attributes without disturbing
existing code. (you'll note that this results in a seemingly
redundant if() in the format function, but that will no longer be
the case as soon as a 2nd attribute is added).
In the future, new attributes for the virtio driver backend can be
added to the "virtio" struct, and any other network device backend that
needs an attribute will have its own struct added to the "driver"
union.
The introduction of the v3 migration protocol, along with
support for migration cookies, will significantly expand
the size of the migration code. Move it all to a separate
file to make it more manageable
The functions are not moved 100%. The API entry points
remain in the main QEMU driver, but once the public
virDomainPtr is resolved to the internal virDomainObjPtr,
all following code is moved.
This will allow the new v3 API entry points to call into the
same shared internal migration functions
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainFormatXML helper method
* src/qemu/qemu_driver.c: Remove all migration code
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Add
all migration code.
Move the qemudStartVMDaemon and qemudShutdownVMDaemon
methods into a separate file, renaming them to
qemuProcessStart, qemuProcessStop. All helper methods
called by these are also moved & renamed to match
* src/Makefile.am: Add qemu_process.c/.h
* src/qemu/qemu_command.c: Add qemuDomainAssignPCIAddresses
* src/qemu/qemu_command.h: Add VNC port min/max
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
domain event queue helpers
* src/qemu/qemu_driver.c, src/qemu/qemu_driver.h: Remove
all QEMU process startup/shutdown functions
* src/qemu/qemu_process.c, src/qemu/qemu_process.h: Add
all QEMU process startup/shutdown functions
"qemudDomainSaveFlag" goto wrong label "endjob", which will cause
error when security manager trying to restore label (regression).
As it's more reasonable to check if vm is shutoff immediately, and
return right away if it is, remove the checking in "qemudDomainSaveFlag",
and add checking in "qemudDomainSave".
* src/qemu/qemu_driver.c
The code expected that host CPU architecture matches the architecture on
which libvirt runs. This is normally true but not in tests, where host
CPU is faked to produce consistent results.
The processWatchdogEvent fix is real, although it can only trigger
on OOM, since bad things happen if doCoreDump is called with a NULL
pathname argument. The other fixes silence clang, but aren't a real
bug because virReportErrorHelper tolerates a NULL format string even
though *printf does not.
* src/qemu/qemu_driver.c (processWatchdogEvent): Exit on OOM.
(qemuDomainIsActive, qemuDomainIsPersistent, qemuDomainIsUpdated):
Provide valid message.
Commit 9962e406c6 introduced a
problem where if the VM failed to startup, it would not be
correctly cleaned up. Amongst other things the SELinux
security label would not be removed, which prevents the VM
from ever starting again.
The virDomainIsActive() check at the start of qemudShutdownVMDaemon
checks for vm->def->id not being -1. By moving the assignment of the
VM id to the start of qemudStartVMDaemon, we can ensure cleanup will
occur on failure
* src/qemu/qemu_driver.c: Move initialization of 'vm->def->id'
so that qemudShutdownVMDaemon() will process the shutdown
Suspending a VM which contains shell meta characters doesn't work with
libvirt-0.8.7:
/var/log/libvirt/qemu/andreas_231-ne\ doch\ nicht.log:
sh: -c: line 0: syntax error near unexpected token `doch'
sh: -c: line 0: `cat | { dd bs=4096 seek=1 if=/dev/null && dd bs=1048576; }
Although target="andreas_231-ne doch nicht" contains shell meta
characters (here: blanks), they are not properly escaped by
src/qemu/qemu_monitor_{json,text}.c#qemuMonitor{JSON,Text}MigrateToFile()
First, the filename needs to be properly escaped for the shell, than
this command line has to be properly escaped for qemu again.
For this to work, remove the old qemuMonitorEscapeArg() wrapper, rename
qemuMonitorEscape() to it removing the handling for shell=TRUE, and
implement a new qemuMonitorEscapeShell() returning strings using single
quotes.
Using double quotes or escaping special shell characters with backslashes
would also be possible, but the set of special characters heavily
depends on the concrete shell (dsh, bash, zsh) and its setting (history
expansion, interactive use, ...)
Signed-off-by: Philipp Hahn <hahn@univention.de>
QEMUD_CMD_FLAG_PCI_MULTIBUS should be set in the function
qemuCapsExtractVersionInfo()
The flag QEMUD_CMD_FLAG_PCI_MULTIBUS is used in the function
qemuBuildDeviceAddressStr(). All callers get qemuCmdFlags
by the function qemuCapsExtractVersionInfo() except that
testCompareXMLToArgvFiles() in qemuxml2argvtest.c.
So we should set QEMUD_CMD_FLAG_PCI_MULTIBUS in the function
qemuCapsExtractVersionInfo() instead of qemuBuildCommandLine()
because the function qemuBuildCommandLine() does not be called
when we attach a pci device.
tests: set QEMUD_CMD_FLAG_PCI_MULTIBUS in testCompareXMLToArgvFiles()
set QEMUD_CMD_FLAG_PCI_MULTIBUS before calling qemuBuildCommandLine()
as the flags is not set by qemuCapsExtractVersionInfo().
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Quite a few hosts don't have cgroups mounted and so see warnings
from libvirt logged, which then cause bug reports, etc. Reduce
the log level to INFO so they're not visible by default
* src/qemu/qemu_driver.c: Reduce log level for cgroups
When probing machine types if the QEMU binary does not exist
we get a hard to diagnose error, due to the execve() in the
child failing
error: internal error Child process exited with status 1.
Add an explicit check so that we get
error: Cannot find QEMU binary /usr/libexec/qem3u-kvm: No such file or directory
* src/qemu/qemu_capabilities.c: Check for QEMU binary
qemu 0.13.0 (at least as built for Fedora 14, and also backported to
RHEL 6.0 qemu) supported an older syntax for a spicevmc channel; it's
not as flexible (it has an implicit name and hides the chardev
aspect), but now that we support spicevmc, we might as well target
both variants.
* src/qemu/qemu_capabilities.h (QEMUD_CMD_FLAG_DEVICE_SPICEVMC):
New flag.
* src/qemu/qemu_capabilities.c (qemuCapsParseDeviceStr): Set it
correctly.
* src/qemu/qemu_command.h (qemuBuildVirtioSerialPortDevStr): Drop
declaration.
* src/qemu/qemu_command.c (qemuBuildVirtioSerialPortDevStr): Alter
signature, check flag.
(qemuBuildCommandLine): Adjust caller and check flag.
* tests/qemuhelptest.c (mymain): Update test.
* tests/qemuxml2argvtest.c (mymain): New test.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc-old.xml:
New file.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc-old.args:
Likewise.
Adds <smartcard mode='passthrough' type='spicevmc'/>, which uses the
new <channel name='smartcard'/> of <graphics type='spice'>.
* docs/schemas/domain.rng: Support new XML.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.h (virDomainGraphicsSpiceChannelName): New
enum value.
(virDomainChrSpicevmcName): New enum.
(virDomainChrSourceDef): Distinguish spicevmc types.
* src/conf/domain_conf.c (virDomainGraphicsSpiceChannelName): Add
smartcard.
(virDomainSmartcardDefParseXML): Parse it.
(virDomainChrDefParseXML, virDomainSmartcardDefParseXML): Set
spicevmc name.
(virDomainChrSpicevmc): New enum conversion functions.
* src/libvirt_private.syms: Export new functions.
* src/qemu/qemu_command.c (qemuBuildChrChardevStr): Conditionalize
name.
* tests/qemuxml2argvtest.c (domain): New test.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-passthrough-spicevmc.args:
New file.
* tests/qemuxml2argvdata/qemuxml2argv-smartcard-passthrough-spicevmc.xml:
Likewise.
Inspired by https://bugzilla.redhat.com/show_bug.cgi?id=615757
Add a new character device backend for virtio serial channels that
activates the QEMU spice agent on the main channel using the vdagent
spicevmc connection. The <target> must be type='virtio', and supports
an optional name that specifies how the guest will see the channel
(for now, name must be com.redhat.spice.0).
<channel type='spicevmc'>
<target type='virtio'/>
<address type='virtio-serial' controller='1' bus='0' port='3'/>
</channel>
* docs/schemas/domain.rng: Support new XML.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.h (virDomainChrType): New enum value.
* src/conf/domain_conf.c (virDomainChr): Add spicevmc.
(virDomainChrDefParseXML, virDomainChrSourceDefParseXML)
(virDomainChrDefParseTargetXML): Parse and enforce proper use.
(virDomainChrSourceDefFormat, virDomainChrDefFormat): Format.
* src/qemu/qemu_command.c (qemuBuildChrChardevStr)
(qemuBuildCommandLine): Add qemu support.
* tests/qemuxml2argvtest.c (domain): New test.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc.xml: New
file.
* tests/qemuxml2argvdata/qemuxml2argv-channel-spicevmc.args:
Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Qemu smartcard/spicevmc support exists on branches (such as
http://cgit.freedesktop.org/~alon/qemu/commit/?h=usb_ccid.v15&id=024a37b)
but is not yet upstream. The added -help output matches a scratch build
that will be close to the RHEL 6.1 qemu-kvm.
* src/qemu/qemu_capabilities.h (QEMUD_CMD_FLAG_CCID_EMULATED)
(QEMUD_CMD_FLAG_CCID_PASSTHRU, QEMUD_CMD_FLAG_CHARDEV_SPICEVMC):
New flags.
* src/qemu/qemu_capabilities.c (qemuCapsComputeCmdFlags)
(qemuCapsParseDeviceStr): Check for smartcard capabilities.
(qemuCapsExtractVersionInfo): Tweak comment.
* tests/qemuhelptest.c (mymain): New test.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel61: New file.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel61-device: Likewise.
Currently users who want to use virDomainQemuMonitorCommand() API or
it's virsh equivalent has to use the same protocol as libvirt uses for
communication to qemu. Since the protocol is QMP with current qemu and
HMP much more usable for humans, one ends up typing something like the
following:
virsh qemu-monitor-command DOM \
'{"execute":"human-monitor-command","arguments":{"command-line":"info kvm"}}'
which is not a very convenient way of debugging qemu.
This patch introduces --hmp option to qemu-monitor-command, which says
that the provided command is in HMP. If libvirt uses QMP to talk with
qemu, the command will automatically be converted into QMP. So the
example above is simplified to just
virsh qemu-monitor-command --hmp DOM "info kvm"
Also the result is converted from
{"return":"kvm support: enabled\r\n"}
to just plain HMP:
kvm support: enabled
If libvirt talks to qemu in HMP, --hmp flag is obviously a noop.
* src/qemu/qemu_driver.c (qemudShutdownVMDaemon): Check that vm is
still active.
Reported by Wen Congyang as follows:
Steps to reproduce this bug:
1. use gdb to debug libvirtd, and set breakpoint in the function
qemuConnectMonitor()
2. start a vm, and the libvirtd will be stopped in qemuConnectMonitor()
3. kill -STOP $(cat /var/run/libvirt/qemu/<domain>.pid)
4. continue to run libvirtd in gdb, and libvirtd will be blocked in the
function qemuMonitorSetCapabilities()
5. kill -9 $(cat /var/run/libvirt/qemu/<domain>.pid)
Here is log of the qemu:
=========
LC_ALL=C PATH=/sbin:/usr/sbin:/bin:/usr/bin ...
char device redirected to /dev/pts/3
2011-01-27 09:38:48.101: shutting down
2011-01-27 09:41:26.401: shutting down
=========
The vm is shut down twice. I do not know whether this behavior has
side effect, but I think we should shutdown the vm only once.
Depending if the qemu binary supports multiple pci-busses, the device
options will contain "bus=pci" or "bus=pci.0".
Only x86_64 and i686 seem to have support for multiple PCI-busses. When
a guest of these architectures is started, set the
QEMUD_CMD_FLAG_PCI_MULTIBUS flag.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Command line building for incoming tunneled migration is missed,
as a result, all the tunneled migration will fail with "unknown
migration protocol".
* src/qemu/qemu_command.c
Use it in all places where a memory or storage request size is converted
to a larger granularity. This avoids requesting too small memory or storage
sizes that could result from the truncation done by a simple division.
This extends the round up fix in 6002e0406c
to the whole codebase.
Instead of reporting errors for odd values in the VMX code round them up.
Update the QEMU Argv tests accordingly as the original memory size 219200
isn't a even multiple of 1024 and is rounded up to 215 megabyte now. Change
it to 219100 and 219136. Use two different values intentionally to make
sure that rounding up works.
Update virsh.pod accordingly, as rounding down and rejecting are replaced
by rounding up.
Fixes test failure that was overlooked after commit 1e1f7a8950.
* daemon/Makefile.am (check-local): Let 'make check' fail on error.
* daemon/test_libvirtd.aug: Move qemu-specific option...
* src/qemu/test_libvirtd_qemu.aug: ...into correct test.
* src/qemu/libvirtd_qemu.aug: Parse new option.
qemu allows the user to choose what io storage api should be used,
either the default (threads) or native (linux aio) which in the latter
case can result in better performance.
Based on a patch originally by Matthias Dahl.
Red Hat Bugzilla #591703
Signed-off-by: Eric Blake <eblake@redhat.com>
The refactoring of QEMU command startup was comitted with
a couple of VIR_WARN lines left in from debugging.
* src/qemu/qemu_driver.c: Remove log warning lines
When qemuMonitorSetCapabilities() fails, there is no need to
call qemuMonitorClose(), because the caller will already see
the error code and tear down the entire VM. The extra call to
qemuMonitorClose resulted in a double-free due to it removing
a ref count prematurely.
* src/qemu/qemu_driver.c: Remove premature close of monitor
Regression in commit caa805ea let a lot of bad messages slip in.
* cfg.mk (msg_gen_function): Fix function name.
* src/qemu/qemu_cgroup.c (qemuRemoveCgroup): Fix fallout from
'make syntax-check'.
* src/qemu/qemu_driver.c (qemudDomainGetInfo)
(qemuDomainWaitForMigrationComplete, qemudStartVMDaemon)
(qemudDomainSaveFlag, qemudDomainAttachDevice)
(qemuDomainUpdateDeviceFlags): Likewise.
* src/qemu/qemu_hotplug.c (qemuDomainAttachHostUsbDevice)
(qemuDomainDetachPciDiskDevice, qemuDomainDetachSCSIDiskDevice):
Likewise.
When attaching device from a xml file and the device is mis-configured,
virsh gives mis-leading message "out of memory". This patch fixes this.
Signed-off-by: Eric Blake <eblake@redhat.com>
* src/qemu/qemu_command.c (qemuBuildChrChardevStr): Alter the
chardev alias.
(qemuBuildCommandLine): Output an id for the chardev counterpart.
* tests/qemuxml2argvdata/*: Update tests to match.
Reported by Daniel P. Berrange.
Steps to reproduce this bug:
1. service libvirtd start
2. virsh start <domain>
3. kill -STOP $(cat /var/run/libvirt/qemu/<domain>.pid)
4. service libvirtd restart
5. kill -9 $(cat /var/run/libvirt/qemu/<domain>.pid)
Then libvirtd will core dump or be in deadlock state.
Make sure that json is built into libvirt and the version
of qemu is newer than 0.13.0.
The reason of libvirtd cores dump is that:
We add vm->refs when we alloc the memory, and decrease it
in the function qemuHandleMonitorEOF() in other thread.
We add vm->refs in the function qemuConnectMonitor() and
decrease it when the vm is inactive.
The libvirtd will block in the function qemuMonitorSetCapabilities()
because the vm is stopped by signal SIGSTOP. Now the vm->refs is 2.
Then we kill the vm by signal SIGKILL. The function
qemuMonitorSetCapabilities() failed, and then we will decrease vm->refs
in the function qemuMonitorClose().
In another thread, mon->fd is broken and the function
qemuHandleMonitorEOF() is called.
If qemuHandleMonitorEOF() decreases vm->refs before qemuConnectMonitor()
returns, vm->refs will be decrease to 0 and the memory is freed.
We will call qemudShutdownVMDaemon() as qemuConnectMonitor() failed.
The memory has been freed, so qemudShutdownVMDaemon() is too dangerous.
We will reference NULL pointer in the function virDomainConfVMNWFilterTeardown():
=============
void
virDomainConfVMNWFilterTeardown(virDomainObjPtr vm) {
int i;
if (nwfilterDriver != NULL) {
for (i = 0; i < vm->def->nnets; i++)
virDomainConfNWFilterTeardown(vm->def->nets[i]);
}
}
============
vm->def->nnets is not 0 but vm->def->nets is NULL(We don't set vm->def->nnets
to 0 when we free vm).
We should add an extra reference of vm to avoid vm to be deleted if
qemuConnectMonitor() failed.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
If a guest image is saved in compressed format, and the restore fails
in some way after the intermediate process used to uncompress the
image has been started, but before qemu has been started to hook up to
the uncompressor, libvirt will endlessly wait for the uncompressor to
finish, but it never will because it's still waiting to have something
hooked up to drain its output.
The solution is to close the pipes on both sides of the uncompressor,
then send a SIGTERM before calling waitpid on it (only if the restore
has failed, of course).
This patch is a partial resolution to the following bug:
https://bugzilla.redhat.com/show_bug.cgi?id=667756
(to complete the fix, an updated selinux-policy package is required,
to add the policy that allows libvirt to set the context of a fifo,
which was previously not allowed).
Explanation : When an incoming migration is over a pipe (for example,
if the image was compressed and is being fed through gzip, or was on a
root-squash nfs server, so needed to be opened by a child process
running as a different uid), qemu cannot read it unless the selinux
context label for the pipe has been set properly.
The solution is to check the fd used as the source of the migration
just before passing it to qemu; if it's a fifo (implying that it's a
pipe), we call the newly added virSecurityManagerSetFDLabel() function
to set the context properly.
The problem was introduced by commit 4303c91, which removed the checking
of domain state, this patch is to fix it.
Otherwise, improper error will be thrown, e.g.
error: Failed to save domain rhel6 state
error: cannot resolve symlink /var/lib/libvirt/qemu/save/rhel6.save: No such
file or directory
In QEMU, the card itself is a PCI device, but it requires a codec
(either -device hda-output or -device hda-duplex) to actually output
sound. Specifying <sound model='ich6'/> gives us -device intel-hda
-device hda-duplex I think it's important that a simple <sound model='ich6'/>
sets up a useful codec, to have consistent behavior with all other sound cards.
This is basically Dan's proposal of
<sound model='ich6'>
<codec type='output' slot='0'/>
<codec type='duplex' slot='3'/>
</sound>
without the codec bits implemented.
The important thing is to keep a consistent API here, we don't want some
<sound> devs require tweaking codecs but not others. Steps I see to
accomplishing this:
- every <sound> device has a <codec type='default'/> (unless codecs are
manually specified)
- <codec type='none'/> is required to specify 'no codecs'
- new audio settings like mic=on|off could then be exposed in
<sound> or <codec> in a consistent manner for all sound models
v2:
Use model='ich6'
v3:
Use feature detection, from eblake
Set codec id, bus, and cad values
v4:
intel-hda isn't supported if -device isn't available
v5:
Comment spelling fixes
If vnc_auto_unix_socket is enabled, any VNC devices without a hardcoded
listen or socket value will be setup to serve over a unix socket in
/var/lib/libvirt/qemu/$vmname.vnc.
We store the generated socket path in the transient VM definition at
CLI build time.
QEMU supports serving VNC over a unix domain socket rather than traditional
TCP host/port. This is specified with:
<graphics type='vnc' socket='/foo/bar/baz'/>
This provides better security access control than VNC listening on
127.0.0.1, but will cause issues with tools that rely on the lax security
(virt-manager in fedora runs as regular user by default, and wouldn't be
able to access a socket owned by 'qemu' or 'root').
Also not currently supported by any clients, though I have patches for
virt-manager, and virt-viewer should be simple to update.
v2:
schema: Make listen vs. socket a <choice>
This will allow us to record transient runtime state in vm->def, like
default VNC parameters. Accomplish this by adding an extra 'live' parameter
to SetDefTransient, with similar semantics to the 'live' flag for
AssignDef.
When restoring a saved qemu instance via JSON monitor, the vm is
left in a paused state. Turns out the 'cont' cmd was failing with
"MigrationExpected" error class and "An incoming migration is
expected before this command can be executed" error description
due to migration (restore) not yet complete.
Detect if 'cont' cmd fails with "MigrationExpecte" error class and
retry 'cont' cmd.
V2: Fix potential double-free noted by Laine Stump
Report VIR_ERR_CONFIG_UNSUPPORTED instead of VIR_ERR_INTERNAL_ERROR,
as it's valid in our domain schema, just unsupported by hypervisor
here.
* src/qemu/qemu_command.c
The code which set VNC passwords correctly had fallback for
the set_password command, but was lacking it for the
expire_password command. This made it impossible to start
a guest. It also failed to check whether QEMU was still
running after the initial 'set_password' command completed
* src/qemu/qemu_hotplug.c: Fix error handling when
password expiry fails
* src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_text.c: Fix
return code for missing expire_password command
Avoid overwriting the real error message with a generic
OOM failure message, when machine type probe fails
* src/qemu/qemu_driver.c: Don't overwrite error
The function virUnrefConnect() may call virReleaseConnect() to release
the dest connection, and the function virReleaseConnect() will call
conn->driver->close().
So the function virUnrefConnect() should be surrounded by
qemuDomainObjEnterRemoteWithDriver() and
qemuDomainObjExitRemoteWithDriver() to prevent possible deadlock between
two communicating libvirt daemons.
See commit f0c8e1cb37 for further details.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
In some circumstances, libvirtd would issue two STOPPED events after it
stopped a domain. This was because an EOF event can arrive after a qemu
process is killed but before qemuMonitorClose() is called.
qemuHandleMonitorEOF() should ignore EOF when the domain is not running.
I wasn't able to reproduce this bug directly, only after adding an
artificial sleep() into qemudShutdownVMDaemon().
Fixes regression introduced in commit 2211518, where all qemu 0.12.x
fails to start, as does qemu 0.13.x lacking the pci-assign device.
Prior to 2211518, the code was just ignoring a non-zero exit status
from the qemu child, but the virCommand code checked this to avoid
masking any other issues, which means the real bug of provoking
non-zero exit status has been latent for a longer time.
* src/qemu/qemu_capabilities.c (qemuCapsExtractVersionInfo): Check
for -device driver,? support.
(qemuCapsExtractDeviceStr): Avoid failure if all probed devices
are unsupported.
Reported by Ken Congyang.
https://bugzilla.redhat.com/show_bug.cgi?id=620363
When using -incoming stdio or -incoming exec:, qemu keeps the
stdin fd open long after the migration is complete. Not to
mention that exec:cat is horribly inefficient, by doubling the
I/O and going through a popen interface in qemu.
The new -incoming fd: of qemu 0.12.0 closes the fd after using
it, and allows us to bypass an intermediary cat process for
less I/O.
* src/qemu/qemu_command.h (qemuBuildCommandLine): Add parameter.
* src/qemu/qemu_command.c (qemuBuildCommandLine): Support
migration via fd: when possible. Consolidate migration handling
into one spot, now that it is more complex.
* src/qemu/qemu_driver.c (qemudStartVMDaemon): Update caller.
* tests/qemuxml2argvtest.c (mymain): Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-restore-v2-fd.args: New file.
* tests/qemuxml2argvdata/qemuxml2argv-restore-v2-fd.xml: Likewise.
Display or set unlimited values for memory parameters. Unlimited is
represented by INT64_MAX in memory cgroup.
Signed-off-by: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Reported-by: Justin Clift <jclift@redhat.com>
This is in response to a request in:
https://bugzilla.redhat.com/show_bug.cgi?id=665293
In short, under heavy load, it's possible for qemu's networking to
lock up due to the tap device's default 1MB sndbuf being
inadequate. adding "sndbuf=0" to the qemu commandline -netdevice
option will alleviate this problem (sndbuf=0 actually sets it to
0xffffffff).
Because we must be able to explicitly specify "0" as a value, the
standard practice of "0 means not specified" won't work here. Instead,
virDomainNetDef also has a sndbuf_specified, which defaults to 0, but
is set to 1 if some value was given.
The sndbuf value is put inside a <tune> element of each <interface> in
the domain. The intent is that further tunable settings will also be
placed inside this element.
<interface type='network'>
...
<tune>
<sndbuf>0</sndbuf>
...
</tune>
</interface>
This patch is in response to
https://bugzilla.redhat.com/show_bug.cgi?id=643050
The existing libvirt support for the vhost-net backend to the virtio
network driver happens automatically - if the vhost-net device is
available, it is always enabled, otherwise the standard userland
virtio backend is used.
This patch makes it possible to force whether or not vhost-net is used
with a bit of XML. Adding a <driver> element to the interface XML, eg:
<interface type="network">
<model type="virtio"/>
<driver name="vhost"/>
will force use of vhost-net (if it's not available, the domain will
fail to start). if driver name="qemu", vhost-net will not be used even
if it is available.
If there is no <driver name='xxx'/> in the config, libvirt will revert
to the pre-existing automatic behavior - use vhost-net if it's
available, and userland backend if vhost-net isn't available.
We try to use that command first when setting a VNC/SPICE password. If
that doesn't work we fallback to the legacy VNC only password
Allow an expiry time to be set, if that doesn't work, throw an error
if they try to use SPICE.
Change since v1:
- moved qemuInitGraphicsPasswords to qemu_hotplug, renamed
to qemuDomainChangeGraphicsPasswords.
- updated what looks like a typo (that appears to work anyway) in
initial patch from Daniel:
- ret = qemuInitGraphicsPasswords(driver, vm,
- VIR_DOMAIN_GRAPHICS_TYPE_SPICE,
- &vm->def->graphics[0]->data.vnc.auth,
- driver->vncPassword);
+ ret = qemuInitGraphicsPasswords(driver, vm,
+ VIR_DOMAIN_GRAPHICS_TYPE_SPICE,
+ &vm->def->graphics[0]->data.spice.auth,
+ driver->spicePassword);
Based on patch by Daniel P. Berrange <berrange@redhat.com>.
* src/qemu/qemu_capabilities.h (qemuCapsParseDeviceStr): New
prototype.
* src/qemu/qemu_capabilities.c (qemuCapsParsePCIDeviceStrs)
Rename and split...
(qemuCapsExtractDeviceStr, qemuCapsParseDeviceStr): ...to make it
easier to add and test device-specific checks.
(qemuCapsExtractVersionInfo): Update caller.
* tests/qemuhelptest.c (testHelpStrParsing): Also test parsing of
device-related flags.
(mymain): Update expected flags.
* tests/qemuhelpdata/qemu-0.12.1-device: New file.
* tests/qemuhelpdata/qemu-kvm-0.12.1.2-rhel60-device: New file.
* tests/qemuhelpdata/qemu-kvm-0.12.3-device: New file.
* tests/qemuhelpdata/qemu-kvm-0.13.0-device: New file.
* src/qemu/qemu_capabilities.c (qemuCapsProbeMachineTypes)
(qemuCapsProbeCPUModels, qemuCapsParsePCIDeviceStrs)
(qemuCapsExtractVersionInfo): Use virCommand rather than virExec.
If the emulator doesn't support SDL graphic, we should reject
the use of SDL graphic xml with error messages, but not ignore
it silently, and pretend things are fine.
"-sdl" flag was exposed explicitly by qemu since 0.10.0, more detail:
http://www.redhat.com/archives/libvir-list/2011-January/msg00442.html
And we already have capability flag "QEMUD_CMD_FLAG_0_10", which
could be used to prevent the patch affecting the older versions
of QEMU.
* src/qemu/qemu_command.c
Skip IB700 when assigning PCI slots.
Note: the I6300ESB watchdog _is_ a PCI device.
To test this: I applied this patch to libvirt-0.8.3-2.fc14 (rebasing
it slightly: qemu_command.c didn't exist in that version) and
installed this on my machine, then tested that I could successfully
add an ib700 watchdog device to a guest, start the guest, and the
ib700 was available to the guest. I also added an i6300esb (PCI)
watchdog to another guest, and verified that libvirt assigned a PCI
device to it, that the guest could be started, and that i6300esb was
present in the guest.
Note that if you previously had a domain with a ib700 watchdog, it
would have had an <address type='pci' .../> clause added to it in the
libvirt configuration. This patch does not attempt to remove this.
You cannot start such a domain -- qemu gives an error if you try.
With this patch you are able to remove the bogus address element
without libvirt adding it back.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
The current security driver usage requires horrible code like
if (driver->securityDriver &&
driver->securityDriver->domainSetSecurityHostdevLabel &&
driver->securityDriver->domainSetSecurityHostdevLabel(driver->securityDriver,
vm, hostdev) < 0)
This pair of checks for NULL clutters up the code, making the driver
calls 2 lines longer than they really need to be. The goal of the
patchset is to change the calling convention to simply
if (virSecurityManagerSetHostdevLabel(driver->securityDriver,
vm, hostdev) < 0)
The first check for 'driver->securityDriver' being NULL is removed
by introducing a 'no op' security driver that will always be present
if no real driver is enabled. This guarentees driver->securityDriver
!= NULL.
The second check for 'driver->securityDriver->domainSetSecurityHostdevLabel'
being non-NULL is hidden in a new abstraction called virSecurityManager.
This separates the driver callbacks, from main internal API. The addition
of a virSecurityManager object, that is separate from the virSecurityDriver
struct also allows for security drivers to carry state / configuration
information directly. Thus the DAC/Stack drivers from src/qemu which
used to pull config from 'struct qemud_driver' can now be moved into
the 'src/security' directory and store their config directly.
* src/qemu/qemu_conf.h, src/qemu/qemu_driver.c: Update to
use new virSecurityManager APIs
* src/qemu/qemu_security_dac.c, src/qemu/qemu_security_dac.h
src/qemu/qemu_security_stacked.c, src/qemu/qemu_security_stacked.h:
Move into src/security directory
* src/security/security_stack.c, src/security/security_stack.h,
src/security/security_dac.c, src/security/security_dac.h: Generic
versions of previous QEMU specific drivers
* src/security/security_apparmor.c, src/security/security_apparmor.h,
src/security/security_driver.c, src/security/security_driver.h,
src/security/security_selinux.c, src/security/security_selinux.h:
Update to take virSecurityManagerPtr object as the first param
in all callbacks
* src/security/security_nop.c, src/security/security_nop.h: Stub
implementation of all security driver APIs.
* src/security/security_manager.h, src/security/security_manager.c:
New internal API for invoking security drivers
* src/libvirt.c: Add missing debug for security APIs
When dynamic_ownership=0, saved images must be owned by the same uid
as is used to run the qemu process, otherwise restore won't work. To
accomplish this, qemuSecurityDACRestoreSavedStateLabel() needs to
simply return when it's called.
This fix is in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=661720
While doing some testing with Qemu and creating huge logfiles I encountered the case where the VM could not start anymore due to the lseek() to the end of the Qemu VM's log file failing. The patch below fixes the problem by replacing the previously used 'int' with 'off_t'.
To reproduce this error, you could do the following:
dd if=/dev/zero of=/var/log/libvirt/qemu/<name of VM>.log bs=1024 count=$((1024*2048))
and you should get an error like this:
error: Failed to start domain <name of VM>
error: Unable to seek to -2147482651 in /var/log/libvirt/qemu/<name of VM>.log: Success
This patch fixes https://bugzilla.redhat.com/show_bug.cgi?id=664406
If qemu is run as a different uid, it has been unable to access mode
0660 files that are owned by a different user, but with a group that
the qemu is a member of (aside from the one group listed in the passwd
file), because initgroups() is not being called prior to the
exec. initgroups will change the group membership of the process (and
its children) to match the new uid.
To make this happen, the setregid()/setreuid() code in
qemuSecurityDACSetProcessLabel has been replaced with a call to
virSetUIDGID(), which does both of those, plus calls initgroups.
Similar, but not identical, code in qemudOpenAsUID() has been replaced
with virSetUIDGID(). This not only consolidates the functionality to a
single location, but also potentially fixes some as-yet unreported
bugs.
Shorten qemuDomainSnapshotWriteSnapshotMetadata function name
and make it take a snapshot pointer instead of dealing with
the current snapshot. Update other functions accordingly.
Add a qemuDomainSnapshotReparentChildren hash iterator to
reparent the children of a snapshot that is being deleted. Use
qemuDomainSnapshotWriteMetadata to write updated metadata
to disk.
This fixes a problem where outdated parent information breaks
the snapshot tree and hinders the deletion of child snapshots.
Reported by Philipp Hahn.
Network disks are accessed by qemu directly, and have no
associated file on the host, so checking for file ownership etc.
is unnecessary.
Signed-off-by: Josh Durgin <joshd@hq.newdream.net>
The QEMU driver file is far too large. Move all the hotplug
helper code out into a separate file. No functional change.
* src/qemu/qemu_hotplug.c, src/qemu/qemu_hotplug.h,
src/Makefile.am: Add hotplug helper file
* src/qemu/qemu_driver.c: Delete hotplug code
To allow the APIs to be used from separate files, move the domain
lock / job helper code into qemu_domain.c
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add domain lock
/ job code
* src/qemu/qemu_driver.c: Remove domain lock / job code
To allow their use from other source files, move qemuDriverLock
and qemuDriverUnlock to qemu_conf.h and make them non-static
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Add qemuDriverLock
qemuDriverUnlock
* src/qemu/qemu_driver.c: Remove qemuDriverLock and qemuDriverUnlock
The QEMU driver file is far too large. Move all the hostdev
helper code out into a separate file. No functional change.
* src/qemu/qemu_hostdev.c, src/qemu/qemu_hostdev.h,
src/Makefile.am: Add hostdev helper file
* src/qemu/qemu_driver.c: Delete hostdev code
The QEMU driver file is far too large. Move all the cgroup
helper code out into a separate file. No functional change.
* src/qemu/qemu_cgroup.c, src/qemu/qemu_cgroup.h,
src/Makefile.am: Add cgroup helper file
* src/qemu/qemu_driver.c: Delete cgroup code
The QEMU driver file is far too large. Move all the audit
helper code out into a separate file. No functional change.
* src/qemu/qemu_audit.c, src/qemu/qemu_audit.h,
src/Makefile.am: Add audit helper file
* src/qemu/qemu_driver.c: Delete audit code
Move the code for handling the QEMU virDomainObjPtr private
data, and custom XML namespace into a separate file
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: New file
for private data & namespace code
* src/qemu/qemu_driver.c, src/qemu/qemu_driver.h: Remove
private data & namespace code
* src/qemu/qemu_driver.h, src/qemu/qemu_command.h: Update
includes
* src/Makefile.am: Add src/qemu/qemu_domain.c
The qemu_conf.c code is doing three jobs, driver config file
loading, QEMU capabilities management and QEMU command line
management. Move the command line code into its own file
* src/qemu/qemu_command.c, src/qemu/qemu_command.h: New
command line management code
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Delete command
line code
* src/qemu/qemu_conf.h, src/qemu_conf.c: Adapt for API renames
* src/Makefile.am: add src/qemu/qemu_command.c
* src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_text.c: Add
import of qemu_command.h
The qemu_conf.c code is doing three jobs, driver config file
loading, QEMU capabilities management and QEMU command line
management. Move the capabilities code into its own file
* src/qemu/qemu_capabilities.c, src/qemu/qemu_capabilities.h: New
capabilities management code
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Delete capabilities
code
* src/qemu/qemu_conf.h: Adapt for API renames
* src/Makefile.am: add src/qemu/qemu_capabilities.c
Currently, all of domain "save/dump/managed save/migration"
use the same function "qemudDomainWaitForMigrationComplete"
to wait the job finished, but the error messages are all
about "migration", e.g. when a domain saving job is canceled
by user, "migration was cancled by client" will be throwed as
an error message, which will be confused for user.
As a solution, intoduce two new job types(QEMU_JOB_SAVE,
QEMU_JOB_DUMP), and set "priv->jobActive" to "QEMU_JOB_SAVE"
before saving, to "QEMU_JOB_DUMP" before dumping, so that we
could get the real job type in
"qemudDomainWaitForMigrationComplete", and give more clear
message further.
And as It's not important to figure out what's the exact job
is in the DEBUG and WARN log, also we don't need translated
string in logs, simply repace "migration" with "job" in some
statements.
* src/qemu/qemu_driver.c
Changes common to all network disks:
-Make source name optional in the domain schema, since NBD doesn't use it
-Add a hostName type to the domain schema, and use it instead of genericName, which doesn't include .
-Don't leak host names or ports
-Set the source protocol in qemuParseCommandline
Signed-off-by: Josh Durgin <joshd@hq.newdream.net>
This patch adds network disk support to libvirt/QEMU. The currently
supported protocols are nbd, rbd, and sheepdog. The XML syntax is like
this:
<disk type="network" device="disk">
<driver name="qemu" type="raw" />
<source protocol='rbd|sheepdog|nbd' name="...some image identifier...">
<host name="mon1.example.org" port="6000">
<host name="mon2.example.org" port="6000">
<host name="mon3.example.org" port="6000">
</source>
<target dev="vda" bus="virtio" />
</disk>
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
`dump' watchdog action lets libvirtd to dump the guest when receives a
watchdog event (which probably means a guest crash)
Currently only qemu is supported.
When we get an EOF event on monitor connection, it may be a result of
either crash or graceful shutdown. QEMU which supports async events
(i.e., we are talking to it using JSON monitor) emits SHUTDOWN event on
graceful shutdown. In case we don't get this event by the time monitor
connection is closed, we assume the associated domain crashed.
Currently libvirt doesn't confirm whether the guest has responded to the
disk removal request. In some cases this can leave the guest with
continued access to the device while the mgmt layer believes that it has
been removed. With a recent qemu monitor command[1] we can
deterministically revoke a guests access to the disk (on the QEMU side)
to ensure no futher access is permitted.
This patch adds support for the drive_del() command and introduces it
in the disk removal paths. If the guest is running in a QEMU without this
command we currently explicitly check for unknown command/CommandNotFound
and log the issue.
If QEMU supports the command we issue the drive_del command after we attempt
to remove the device. The guest may respond and remove the block device
before we get to attempt to call drive_del. In that case, we explicitly check
for 'Device not found' from the monitor indicating that the target drive
was auto-deleted upon guest responds to the device removal notification.
1. http://thread.gmane.org/gmane.comp.emulators.qemu/84745
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Currently libvirt doesn't confirm whether the guest has responded to the
disk removal request. In some cases this can leave the guest with
continued access to the device while the mgmt layer believes that it has
been removed. With a recent qemu monitor command[1] we can
deterministically revoke a guests access to the disk (on the QEMU side)
to ensure no futher access is permitted.
This patch adds support for the drive_unplug() command and introduces it
in the disk removal paths. There is some discussion to be had about how
to handle the case where the guest is running in a QEMU without this
command (and the fact that we currently don't have a way of detecting
what monitor commands are available).
Changes since v2:
- use VIR_ERROR to report when unplug command not found
Changes since v1:
- return > 0 when command isn't present, < 0 on command failure
- detect when drive_unplug command isn't present and log error
instead of failing entire command
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
