The real Q35 machine puts the first USB controller set (EHCI+(UHCIx4))
on bus 0 slot 0x1D, and the 2nd USB controller set on bus 0 slot 0x1A,
so let's attempt to make the virtual machine match that for
controllers with auto-assigned addresses when possible.
Three test cases were added to assure that the proper addresses are
assigned - one with a single set of unaddressed USB controllers, one
with 3 (to grab both preferred slots plus one more), and one with the
order of the controller definitions reordered, to assure that the
auto-assignment isn't mixed up by order.
When qemuAssignDevicePCISlots() is looking for companion controllers
for a USB controller that has no PCI address specified, it initializes
a virDevicePCIAddress to 0000:00:00.0, fills it in with the
companion's address if one is found, then checks whether or not there
was a find based on slot == 0. On a system with a single PCI bus, that
is a valid way to check, because slot 0 is reserved, but on most other
PCI buses, slot 0 is not reserved, and is open for use by any
device. This patch adds a separate bool that is set when a companion
is found rather than relying on the faulty information provided with
"slot == 0".
If the q35 specific disable s3/s4 setting isn't supported, fallback to
specifying the PIIX setting, which is the previous behavior. It doesn't
have any effect, but qemu will just warn about it rather than error:
qemu-system-x86_64: Warning: global PIIX4_PM.disable_s3=1 not used
qemu-system-x86_64: Warning: global PIIX4_PM.disable_s4=1 not used
Since it doesn't error, I don't think we should either, since there
may be configs in the wild that already have q35 + disable_s3/4 (via
virt-manager)
The condition was checking for UHCI (and OHCI for ppc64) availability so
that it can specify the proper device instead of legacy usb. However,
for ppc64, we don't need to check both OHCI and UHCI, but only OHCI as
that is the legacy default. The condition is so big that it was just a
matter of time when someone will make a mistake there, so let's use more
lines so that it is visible what the condition checks for.
This fixes usage of -device instead of -usb for ppc64 that supports
pci-usb-ohci and does not support piix3-usb-uhci.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1297020
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If user defines a virtio channel with UNIX socket backend and doesn't
care about the path for the socket (e.g. qemu-agent channel), we still
generate it into the persistent XML. Moreover when then user renames
the domain, due to its persistent socket path saved into the per-domain
directory, it will not start. So let's forget about old generated paths
and also stop putting them into the persistent definition.
https://bugzilla.redhat.com/show_bug.cgi?id=1278068
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
For completeness, use the VIR_TRISTATE_SWITCH_ABSENT for data.file.append
comparisons. Commit ids '70ffa02f' and '53a15aed' just went with the non
zero comparison.
By default, QEMU truncates serial file on open. Sometimes, it could be weird -
for example, when we are trying to investigate some event, which occured several
restarts ago. This patch adds an ability to preserve previous content.
Signed-off-by: Dmitry Mishin <dim@virtuozzo.com>
when appropriate, of course. If the config for a domain specifies boot
order with <boot dev='blah'/> elements, e.g.:
<os>
...
<boot dev='hd'/>
<boot dev='network'/>
</os>
Then the first disk device in the config will have ",bootindex=1"
appended to its qemu commandline -device options, and the first (and
*only* the first) network interface device will get ",bootindex=2".
However, if the first network interface device is a "hostdev" device
(an SRIOV Virtual Function (VF) being assigned to the domain with
vfio), then the bootindex option will *not* be appended. This happens
because the bootindex=n option corresponding to the order of "<boot
dev='network'/>" is added to the -device for the first network device
when network device commandline args are constructed, but if it's a
hostdev network device, its commandline arg is instead constructed in
the loop for hostdevs.
This patch fixes that omission by noticing (in bootHostdevNet) if the
first network device was a hostdev, and if so passing on the proper
bootindex to the commandline generator for hostdev devices - the
result is that ",bootindex=2" will be properly appended to the first
"network" device in the config even if it is really a hostdev
(including if it is assigned from a libvirt network pool). (note that
this is only the case if there is no <bootmenu enabled='yes'/> element
in the config ("-boot menu-on" in qemu) , since the two are mutually
exclusive - when the bootmenu is enabled, the individual per-device
bootindex options can't be used by qemu, and we revert to using "-boot
order=xyz" instead).
If a greater level of control over boot order is desired (e.g., more
than one network device should be tried, or a network device other
than the first one encountered in the config), then <boot
dev='network'/> in the <os> element should not be used; instead, the
individual device elements in the config should be given a "<boot
order='n'/>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1278421
https://bugzilla.redhat.com/show_bug.cgi?id=1240439
Ta-da! Now that we know how to open a macvtap device multiple
times, we can finally enable the multiqueue feature. Everything
else is already prepared (e.g. command line generation) from the
previous iteration where the feature was implemented for
TUN/TAP devices.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
For the multiqueue on macvtaps we are going to need to open
the device multiple times. Currently, this is not supported.
Rework the function, so that upper layers can be reworked too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So yet again one of integer arguments that we use as a boolean.
Since the argument count of the function is unbearably long
enough, lets turn those booleans into flags.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Check if virtio-gpu provides virgl option, and add qemu command line
formatter.
It is enabled with the existing accel3d attribute:
<model type='virtio' heads='1'>
<acceleration accel3d='yes'/>
</model>
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
qemu 2.5 provides virtio video device. It can be used with -device
virtio-vga for primary devices, or -device virtio-gpu for non-vga
devices. However, only the primary device (VGA) is supported with this
patch.
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=1195176
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
'model' attribute was added to a panic device but only one panic
device is allowed. This patch changes panic device presence
from 'optional' to 'zeroOrMore'.
Panic device type used depends on 'model' attribute.
If no model is specified then device type depends on hypervisor
and guest arch. 'pseries' model is used for pSeries guest and
'isa' model is used in other cases.
XML:
<devices>
<panic model='hyperv'/>
</devices>
QEMU command line:
qemu -cpu <cpu_model>,hv_crash
Make callers of qemuBuildCommandLine responsible for providing the URI
which should be passed as a parameter for -incoming.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Since we already make sure before that the domain configuration is
valid we may execute it always at the cost of doing 0 iterations of the
for loop.
This patch will simplify later refactor as it will avoid whitespace
changes.
Make the function usable so that -1 can be passed to it as cell ID so
that we can later enable memory hotplug on non-NUMA guests for certain
architectures.
The previous commit
commit 4e8993a250
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Mon Nov 9 16:20:08 2015 +0000
qemu: assume various QEMU 0.10 features are always available
Added broken handling of -sdl. Instead of duplicating existing
SDL handling code, just ensure it is invoked in the right
scenarios.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The -sdl and -net ...name=XXX arguments were both introduced
in QEMU 0.10, so the QEMU driver can assume they are always
available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.10.0 the -vga argument was introduced, so the
QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.10.0, the -drive cache option stopped using
the on/off value names, so the QEMU driver can assume
use of the new value names.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Since we require QEMU 0.12.0, we can assume that QEMU supports
all of the fd, tcp, unix and exec migration protocols.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
We have twice previously attempted to remove Xenner
support
commit de9be0ab4d
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Wed Aug 22 17:29:01 2012 +0100
Remove xenner support
commit 92572c3d71
Author: Ján Tomko <jtomko@redhat.com>
Date: Wed Feb 18 16:33:50 2015 +0100
Remove code handling the QEMU_CAPS_DOMID capability
This change really does remove the last traces of it
in the capabilities handling code
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.1 the -drive argument can be used to configure
all disks, so the QEMU driver can assume it is always available
and drop support for -hda/-cdrom/etc.
Many of the tests need updating because a great many were
running without CAPS_DRIVE set, so using the -hda legacy
syntax.
Fixing the tests uncovered a bug in the argv -> xml
convertor which failed to handle disk with if=floppy.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The QEMU argv -> virDomainDef conversion code was not handling
-drive arguments using the floppy bus. This caused them to be
added as hard disks instead.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The -no-reboot arg was added in QEMU 0.9.0, so the QEMU driver
can now assume it is always present.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.0 the -vnc option accepts a ':' to separate port
from listen address, so the QEMU driver can assume that support
for listen addresses is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The kQEMU accelerator was deleted in QEMU 0.12, so we no
longer need to support it in the QEMU driver.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
We have macros for both positive and negative string matching.
Therefore there is no need to use !STREQ or !STRNEQ. At the same
time as we are dropping this, new syntax-check rule is
introduced to make sure we won't introduce it again.
Signed-off-by: Ishmanpreet Kaur Khera <khera.ishman@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1249981
When qemuDomainPinIOThread was added in commit id 'fb562614', a check
for the IOThread capability was not needed since a check for iothreadpids
covered the condition where the support for IOThreads was not present.
The iothreadpids array was only created if qemuProcessDetectIOThreadPIDs
was able to query the monitor for IOThreads. It would only do that if
the QEMU_CAPS_OBJECT_IOTHREAD capability was set.
However, when iothreadids were added in commit id '8d4614a5' and the
check for iothreadpids was replaced by a search through the iothreadids[]
array for the matching iothread_id that left open the possibility that
an iothreadids[] array was defined, but the entries essentially pointed
to elements with only the 'iothread_id' defined leaving the 'thread_id'
value of 0 and eventually the cpumap entry of NULL.
This was because, the original IOThreads commit id '72edaae7' only
checked if IOThreads were defined and if the emulator had the IOThreads
capability, then IOThread objects were added at startup. The "capability
failure" check was only done when a disk was assigned to an IOThread in
qemuCheckIOThreads. This was because the initial implementation had no way
to dynamically add IOThreads, but it was possible to dynamically add a
disk to the domain. So the decision was if the domain supported it, then
add the IOThread objects. Then if a disk with an IOThread defined was
added, it could check the capability and fail to add if not there. This
just meant the 'iothreads' value was essentially ignored.
Eventually commit id 'a27ed6e7' allowed for the dynamic addition and
deletion of IOThread objects. So it was no longer necessary to generate
IOThread objects to dynamically attach a disk to. However, the startup
and disk check code was not modified to reflect this.
This patch will move the capability failure check to when IOThread
objects are being added to the command line. Thus a domain that has
IOThreads defined will not be started if the emulator doesn't support
the capability. This means when qemuCheckIOThreads is called to add
a disk, it's no longer necessary to check the capability. Instead the
code can use the IOThreadFind call to indicate that the IOThread
doesn't exist.
Finally because it could be possible to have a domain running with the
iothreadids[] defined prior to this change if libvirtd is restarted each
having mostly empty elements, qemuProcessDetectIOThreadPIDs will check
if there are niothreadids when the QEMU_CAPS_OBJECT_IOTHREAD capability
check fails and remove the elements and array if it exists.
With these changes in place, it turns out the cputune-numatune test
was failing because the right bit wasn't set in the test. So used the
opportunity to fix that and create a test that would expect to fail
with some sort of iothreads defined and used, but not having the
correct capability.
Although theoretically both should be the same value, the niothreadids
should be used in favor of iothreads when performing comparisons. This
leaves the iothreads as a purely numeric value to be saved in the config
file. The one exception to the rule is virDomainIOThreadIDDefArrayInit
where the iothreadids are being generated from the iothreads count since
iothreadids were added after initial iothreads support.
We are using memory-backing-file even when it's not needed, for example
if user requests hugepages for memory backing, but does not specify any
pagesize or memory node pinning. This causes migrations to fail when
migrating from older libvirt that did not do this. So similarly to
commit 7832fac847 which does it for
memory-backend-ram, this commit makes is more generic and
backend-agnostic, so the backend is not used if there is no specific
pagesize of hugepages requested, no nodeset the memory node should be
bound to, no memory access change required, and so on.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1266856
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
So since the introduction of the memory-backend-file object until now we
only added '-mem-path' for non-NUMA guests and we used the parameters of
the memory-backend-file object to specify the path to the hugetlbfs
mount. But hugepages can be also used without memory-backend-file
object, as it used to be before its introduction. Let's just get this
part of the code back and properly append the '-mem-path' for NUMA
guests as well, but only when the memory backend is not needed.
This parameter is already being applied when no numa is requested and
because we still use memory-object-file unconditionally for
hugepage-backed NUMA guests, this should not fire until later.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
That function is called qemuBuildMemPathStr() and will be used in
other places in the future. The change in the test suite is proper due
to the fact that -mem-prealloc makes only sense with -mem-path (from
qemu documentation -- html/qemu-doc.html).
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Support for GICv3 has been recently introduced in qemu using gic-version
option for the 'virt' machine. The option can actually take values of
'2', '3' and 'host', however, since in libvirt this is a numeric
parameter, we limit it only to 2 and 3. Value of 2 is not added to the
command line in order to keep backward compatibility with older qemu
versions.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
When we are starting a qemu process for an incomming migration or
snapshot reloading we should not modify the memory sizes in the domain
since we could potentially change the guest ABI that was tediously
checked before. Additionally the function now updates the initial memory
size according to the NUMA node size, which should not happen if we are
restoring state.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1252685
When implementing memory hotplug I've opted to recalculate the initial
memory size (contents of the <memory> element) as a sum of the sizes of
NUMA nodes when NUMA was enabled. This was based on an assumption that
qemu did not allow starting when the NUMA node size total didn't equal
to the initial memory size. Unfortunately the check was introduced to
qemu just lately.
This patch uses the new XML parser flag to decide whether it's safe to
update the memory size total from the NUMA cell sizes or not.
As an additional improvement we now report an error in case when the
size of hotplug memory would exceed the total memory size.
The rest of the changes assures that the function is called with correct
flags.
Fixes the following error when attempting to add a disk with bus='virtio'
to a machine which actually supports virtio-mmio (caught with ARM virt):
virtio disk cannot have an address of type 'virtio-mmio'
The problem has been likely introduced by
e8d5517254. Before that
qemuAssignDevicePCISlots() was never called for ARM "virt" machine.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
There's a couple reports of things failing in this area (bug 1259070),
but it's tough to tell what's going wrong without stderr from
qemu-bridge-helper. So let's report stderr in the error message
Couple new examples:
virbr0 is inactive:
internal error: /usr/libexec/qemu-bridge-helper --use-vnet --br=virbr0 --fd=21: failed to communicate with bridge helper: Transport endpoint is not connected
stderr=failed to get mtu of bridge `virbr0': No such device
bridge isn't on the ACL:
internal error: /usr/libexec/qemu-bridge-helper --use-vnet --br=br0 --fd=21: failed to communicate with bridge helper: Transport endpoint is not connected
stderr=access denied by acl file
https://bugzilla.redhat.com/show_bug.cgi?id=1258361
When attaching a disk, controller, or rng using an address type ccw
or s390, we need to ensure the support is provided by both the machine.os
and the emulator capabilities (corollary to unconditional setting when
address was not provided for the correct machine.os and emulator.
For an inactive guest, an addition followed by a start would cause the
startup to fail after qemu_command builds the command line and attempts
to start the guest. For an active guest, libvirtd would crash.
Rather than have different usages of STR function in order to determine
whether the domain is s390-ccw or s390-ccw-virtio, make a single API
which will check the machine.os prefix. Then use the function.
Adds a new interface type using UDP sockets, this seems only applicable
to QEMU but have edited tree-wide to support the new interface type.
The interface type required the addition of a "localaddr" (local
address), this then maps into the following xml and qemu call.
<interface type='udp'>
<mac address='52:54:00:5c:67:56'/>
<source address='127.0.0.1' port='11112'>
<local address='127.0.0.1' port='22222'/>
</source>
<model type='virtio'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/>
</interface>
QEMU call:
-net socket,udp=127.0.0.1:11112,localaddr=127.0.0.1:22222
Notice the xml "local" entry becomes the "localaddr" for the qemu call.
reference:
http://lists.gnu.org/archive/html/qemu-devel/2011-11/msg00629.html
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
We are automatically generating some socket paths for domains, but all
those paths end up in a directory that's the same for multiple domains.
The problem is that multiple domains can each run with different
seclabels (users, selinux contexts, etc.). The idea here is to create a
per-domain directory labelled in a way that each domain can access its
own unix sockets.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1146886
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Otherwise the error is just
error: Failed to create domain from test1.xml
error: failed to retrieve file descriptor for interface: Transport endpoint is not connected
since we don't get a sensible error after the fork.
https://bugzilla.redhat.com/show_bug.cgi?id=1210587 (completed)
When generating the default drive address for a SCSI <disk> device,
check the generated address to ensure it doesn't conflict with a SCSI
<hostdev> address. The <disk> address generation algorithm uses the
<target> "dev" name in order to determine which controller and unit
in order to place the device. Since a SCSI <hostdev> device doesn't
require a target device name, its placement on the guest SCSI address
"could" conflict. For instance, if a SCSI <hostdev> exists at
controller=0 unit=0 and an attempt to hotplug 'sda' into the guest
made, there would be a conflict if the <hostdev> is already using
/dev/sda.
This reverts commit ede34470fd, which
was apparently written based on testing performed before commits
1e15be1 and 9a12b6 were pushed upstream. Once those two patches are in
place, commit ede34470 is redundant, and can even cause
incorrect/unexpected behavior when auto-assigning addresses for
virtio-net devices.
Commit e8d5517 updated the domain post-parse to automatically add
pcie-root et al for certain ARM "virt" machinetypes, but didn't update
the function qemuDomainSupportsPCI() which is called later on when we
are auto-assigning PCI addresses and default settings for the PCI
controller <model> and <target> attributes. The result was that PCI
addresses weren't assigned, and the controllers didn't have their
attribute default values set, leading to an error when the domain was
started, e.g.:
internal error: autogenerated dmi-to-pci-bridge options not set
This patch adds the same check made in the earlier patch to
qemuDomainSupportsPCI(), so that PCI address auto-assignment and
target/model default values will be set.
nwfilter uses iptables and ebtables, which only work properly on
tap-based network connections (*not* on macvtap, for example), but we
just ignore any <filterref> elements for other types of networks,
potentially giving users a false sense of security.
This patch checks the network type and fails/logs an error if any
domain <interface> has a <filterref> when the connection isn't using a
tap device.
This resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1180011
This controller can be connected only to a port on a
pcie-switch-upstream-port. It provides a single hotpluggable port that
will accept any PCI or PCIe device, as well as any device requiring a
pcie-*-port (the only current example of such a device is the
pcie-switch-upstream-port).
This controller can be connected only to a pcie-root-port or a
pcie-switch-downstream-port (which will be added in a later patch),
which is the reason for the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_PORT. A pcie-switch-upstream-port provides
32 ports (slot=0 to slot=31) on the downstream side, which can only
have pci controllers of model "pcie-switch-downstream-port" plugged
into them, which is the reason for the other new connect type
VIR_PCI_CONNECT_TYPE_PCIE_SWITCH.
This is backed by the qemu device ioh3420.
chassis and port from the <target> subelement are used to store/set the
respective qemu device options for the ioh3420. Currently, chassis is
set to be the index of the controller, and port is set to
"(slot << 3) + function" (per suggestion from Alex Williamson).
This controller can be connected (at domain startup time only - not
hotpluggable) only to a port on the pcie root complex ("pcie-root" in
libvirt config), hence the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_ROOT. It provides a hotpluggable port that
will accept any PCI or PCIe device.
New attributes must be added to the controller <target> subelement for
this - chassis and port are guest-visible option values that will be
set by libvirt with values derived from the controller's index and pci
address information.
This uses the new subelement/attribute in two ways:
1) If a "pci-bridge" pci controller has no chassisNr attribute, it
will automatically be set to the controller's index as soon as the
controller's PCI address is known (during
qemuDomainAssignPCIAddresses()).
2) when creating the commandline for a pci-bridge device, chassisNr
will be used to set qemu's chassis_nr option (rather than the previous
practice of hard-coding it to the controller's index).
This patch provides qemu support for the contents of <model> in
<controller> for the two existing PCI controller types that need it
(i.e. the two controller types that are backed by a device that must
be specified on the qemu commandline):
1) pci-bridge - sets <model> name attribute default as "pci-bridge"
2) dmi-to-pci-bridge - sets <model> name attribute default as
"i82801b11-bridge".
These both match current hardcoded practice.
The defaults are set at the end of qemuDomainAssignPCIAddresses().
This can't be done earlier because some of the options that will be
autogenerated need full PCI address info for the controller, and
because qemuDomainAssignPCIAddresses() might create extra controllers
which would need default settings added, and that hasn't yet been done
at the time the PostParse callbacks are being run.
qemuDomainAssignPCIAddresses() is still called prior to the XML being
written to disk, though, so the autogenerated defaults are persistent.
qemu capabilities bits aren't checked when the domain is defined, but
rather when the commandline is actually created (so the domain can
possibly be defined on a host that doesn't yet have support for the
given device, or a host different from the one where it will
eventually be run). When the commandline is being generated we compare
the modelName to known qemu device names implementing the given type
of controller, and check the capabilities bit for that device.
virtio-net-pci adapter is capable to use irqfd with vhost-net only in MSI-X
mode, which appears to be available only on PCIe bus, at least on ARM
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Legacy -net option works correctly only with embedded device models, which
do not require any bus specification. Therefore, we should use -device for
PCI hardware
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Rather than provide a somewhat generic error message when the API
returns false, allow the caller to supply a "report = true" option
in order to cause virReportError's to describe which of the 3 paths
that can cause failure.
Some callers don't care about what caused the failure, they just want
to have a true/false - for those, calling with report = false should
be sufficient.
PowerPC pseries based VMs do not support a floppy disk controller.
This prohibits libvirt from creating qemu command with floppy device.
Signed-off-by: Kothapally Madhu Pavan <kmp@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1180486
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This loop occurs just after we've assured that all devices that
require a PCI device have been assigned and all necessary PCI
controllers have been added. It is the perfect place to add other
potentially auto-generated PCI controller attributes that are
dependent on the controller's PCI address (upcoming patch).
There is a convenient loop through all controllers at the end of the
function, but the patch to add new functionality will be cleaner if we
first rearrange that loop a bit.
Note that the loop originally was accessing info.addr.pci.bus prior to
determining that the pci part of the object was valid. This isn't
dangerous in any way, but seemed a bit ugly, so I fixed it.
This reverts commit 7b401c3bda.
Until libvirt is able to differentiate whether heads='1' is just a
leftover from previous libvirt or whether that's added by user on
purpose and also whether the domain was started with the support for
qxl's max_outputs, we cannot incorporate this patch into the tree
due to compatibility reasons.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Allows to specify maximum number of head to QXL driver.
Actually can be a compatiblity problem as heads in the XML configuration
was set by default to '1'.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
For s390-ccw-virtio machines the default bus type is set to ccw.
Specifing an address element allows to override the default.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Adding the recently in qemu added 9pfs support for virtio-ccw.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
If user passes an invalid address for shared memory device to qemu,
neither libvirt nor qemu will report an error, but qemu will auto assign
a pci address to the shared memory device.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
As the backend of shmem server is a unix type chr device, save it in
virDomainChrSourceDef, so we can reuse the existing code for chr device.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Rename qemuBuildShmemDevCmd to qemuBuildShmemDevStr and change the
return type so that it can be reused in the device hotplug code later.
And split the chardev creation part in a new function
qemuBuildShmemBackendStr for reuse in the device hotplug code later.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Since QEMU commit ea96bc6 [1]:
i386: drop FDC in pc-q35-2.4+ if neither it nor floppy drives are wanted
the floppy controller is no longer implicit.
Specify it explicitly on the command line if the machine type version
is 2.4 or later.
Note that libvirt's floppy drives do not result in QEMU implying the
controller, because libvirt uses if=none instead of if=floppy.
https://bugzilla.redhat.com/show_bug.cgi?id=1227880
[1] http://git.qemu.org/?p=qemu.git;a=commitdiff;h=ea96bc6
For the implicit controller, we set them via -global.
Separating them will allow reuse for explicit fdc controller as well.
No functional impact apart from one extra allocation.
Also check the device type when deciding what type the address should
be. Commit 9807c47 (aiming to fix another error in address allocation)
only checked the target type, but its value is different for different
device types. This resulted in an error when trying to attach
a channel with target type 'virtio':
error: Failed to attach device from channel-file.xml
error: internal error: virtio serial device has invalid address type
Make the logic for releasing the address dependent only on
* the address type
* whether it was allocated earlier
to avoid copying the device and target type checks.
https://bugzilla.redhat.com/show_bug.cgi?id=1230039
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1201760
When the domain "<on_crash>coredump-destroy</on_crash>" is set, the
domain wasn't being destroyed, rather it was being rebooted.
Add VIR_DOMAIN_LIFECYCLE_CRASH_COREDUMP_DESTROY to the list of
on_crash types that cause "-no-reboot" to be added to the qemu
command line.
Although defined the same way, fortunately there hadn't been any deviation.
Ensure any assignments to onCrash use VIR_DOMAIN_LIFECYCLE_CRASH_* defs and
not VIR_DOMAIN_LIFECYCLE_* defs
Make sure we only assign the default spicevmc channel name to spicevmc
virtio channels. Caused by commits 3269ee65 and 1133ee2b, which moved
the assignment from XML parsing code to QEMU but failed to keep the
logic.
https://bugzilla.redhat.com/show_bug.cgi?id=1179680
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When support for the pcie-root and dmi-to-pci-bridge buses on a Q35
machinetype was added, I was concerned that even though qemu at the
time allowed plugging a PCI device into a PCIe port, that it might not
be supported in the future. To prevent painful backtracking in the
possible future where this happened, I disallowed such connections
except in a few specific cases requested by qemu developers (indicated
in the code with the flag VIR_PCI_CONNECT_TYPE_EITHER_IF_CONFIG).
Now that a couple years have passed, there is a clear message from
qemu that there is no danger in allowing PCI devices to be plugged
into PCIe ports. This patch eliminates
VIR_PCI_CONNECT_TYPE_EITHER_IF_CONFIG and changes the code to always
allow PCI->PCIe or PCIe->PCI connection *when the PCI address is
specified in the config. (For newly added devices that haven't yet
been given a PCI address, the auto-placement still prefers using the
correct type of bus).
The PCI case of the switch statement in this function contains another
switch statement with a case for each model. Currently every model
except pci-root and pcie-root has a check for index > 0 (since only
those two can have index==0), and the function should never be called
for those two anyway. If we move the check for !pci[e]-root to the top
of the pci case, then we can move the check for index > 0 out of the
individual model cases. This will save repeating that check for the
three new controller models about to be added.
So far the argument has not much meaning and was practically ignored.
This is not good since when doing memory hotplug, the size of desired
hugepage backing is passed in that argument. Taking closer look at the
tests I'm fixing reveals the bug. For instance, while the following is
in the test:
<memory model='dimm'>
<source>
<nodemask>1-3</nodemask>
<pagesize unit='KiB'>4096</pagesize>
</source>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
<address type='dimm' slot='0' base='0x100000000'/>
</memory>
the generated commandline corresponding to this XML was:
-object memory-backend-ram,id=memdimm0,size=536870912,\
host-nodes=1-3,policy=bind
Have you noticed? Yes, memory-backend-ram! Nothing can be further away
from the right answer. The hugepage backing is requested in the XML
and we happily ignore it. This is just not right. It's
memory-backend-file which should have been used:
-object memory-backend-file,id=memdimm0,prealloc=yes,\
mem-path=/dev/hugepages4M/libvirt/qemu,size=536870912,\
host-nodes=1-3,policy=bind
The problem is, that @pagesize passed to qemuBuildMemoryBackendStr
(where this part of commandline is built) was ignored. The hugepage to
back memory was searched only and only by NUMA nodes pinning. This
works only for regular guest NUMA nodes.
Then, I'm changing the hugepages size in the test XMLs too. This is
simply because in the test suite we create dummy mount points just for
2M and 1G hugepages. And in the test 4M was requested. I'm sticking to
2M, but 1G should just work too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1196644
This function constructs the backend (host facing) part of the
memory device. At the beginning, the configured hugepages are
searched to find the best match for given guest NUMA node.
Configured hugepages can have a @nodeset attribute to specify on
which guest NUMA nodes should be the hugepages backing used.
There is, however, one 'corner case'. Users may just tell 'use
hugepages to back all the nodes'. In other words:
<memoryBacking>
<hugepages/>
</memoryBacking>
<cpu>
<numa>
<cell id='0' cpus='0-1' memory='1024000' unit='KiB'/>
</numa>
</cpu>
Our code fails in this case. Well, since there's no @nodeset (nor
any <page/> child element to <hugepages/>) we fail to lookup the
default hugepage size to use.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch provides support for the new watchdog model "diag288".
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
The privileged flag will not change while the configuration might
change. Make the 'privileged' flag member of the driver again and mark
it immutable. Should that ever change add an accessor that will group
reads of the state.
When hotplugging a memory device, there wasn't a check to determine
if there is a conflict with the address space being used by the to
be added memory device and any existing device which is disallowed by qemu.
This patch adds a check to ensure the new device address doesn't
conflict with any existing device.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1220527
This type of information defines attributes of a system
baseboard. With one exception: board type is yet not implemented
in qemu so it's not introduced here either.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1021480
Seems the property has been deprecated for qemu, although seemingly ignored.
This patch enforces from a libvirt perspective that a scsi-block 'lun'
device should not provide the 'serial' property.
Move all the system_* fields into a separate struct. Not only this
simplifies the code a bit it also helps us to identify whether BIOS
info is present. We don't have to check all the four variables for
being not-NULL, but we can just check the pointer to the struct.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Move all the bios_* fields into a separate struct. Not only this
simplifies the code a bit it also helps us to identify whether BIOS
info is present. We don't have to check all the four variables for
being not-NULL, but we can just check the pointer to the struct.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch adds the support of queues attribute of the driver element
for vhost-user interface type. Example:
<interface type='vhostuser'>
<mac address='52:54:00:ee:96:6d'/>
<source type='unix' path='/tmp/vhost2.sock' mode='client'/>
<model type='virtio'/>
<driver queues='4'/>
</interface>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1207692
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
qemu 2.3.0 added the -cpu host,aarch64=off option, which allows using
qemu-system-aarch64 KVM to run armv7l VMs.
Add a capabilities check for it, wire it up in qemu_command, and test
the command line generation.
The guest firmware provides the same functionality as the pvpanic
device, which is not available in QEMU on pSeries, so the domain
XML should be allowed to contain the <panic> element.
On the other hand, unlike the pvpanic device, the guest firmware
can't be configured, so report an error if an address has been
provided in the XML.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182388
When attempting to hotplug a virtio-serial console to a domain
that had no virtio-serial controllers (not even those that
are added by libvirt when some devices need them) at daemon startup,
report a user-friendly error:
error: Failed to attach device from console.xml
error: internal error: no virtio-serial controllers are available
instead of crashing the daemon:
Process terminating with default action of signal 11 (SIGSEGV): dumping core
Access not within mapped region at address 0x8
at 0x531028F: virDomainVirtioSerialAddrNext (domain_addr.c:916)
by 0x531028F: virDomainVirtioSerialAddrAssign (domain_addr.c:1029)
by 0x1CBF68: qemuDomainAttachChrDevice (qemu_hotplug.c:1565)
by 0x1BCD5E: qemuDomainAttachDeviceLive (qemu_driver.c:7997)
by 0x1BCD5E: qemuDomainAttachDeviceFlags (qemu_driver.c:8743)
Introduced in v1.2.14-30-g5903378.
Recent changes to the -M/--machine processing code in qemuParseCommandLine
caused Coverity to determine there was a possible resource leak with how
the 'list' is managed. Rather than try to add virStringFreeList calls
everywhere - just promote list to the top of the variables and free it
within the error processing code. Also required a couple of other tweaks
in order to avoid double free's.
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Implementation is pretty straight-forward. Of course, not all qemus
out there supports the device, so new capability is introduced and
checked prior each use of the device.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So far, we are not reporting if numatune was even defined. The
value of zero is blindly returned (which maps onto
VIR_DOMAIN_NUMATUNE_MEM_STRICT). Unfortunately, we are making
decisions based on this value. Instead, we should not only return
the correct value, but report to the caller if the value is valid
at all.
For better viewing of this patch use '-w'.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Introduces two new -machine option parameters to the QEMU command to
enable/disable the CPACF protected key management operations for a guest:
aes-key-wrap='on|off'
dea-key-wrap='on|off'
The QEMU code maps the corresponding domain configuration elements to the
QEMU -machine option parameters to create the QEMU command:
<cipher name='aes' state='on'> --> aes-key-wrap=on
<cipher name='aes' state='off'> --> aes-key-wrap=off
<cipher name='dea' state='on'> --> dea-key-wrap=on
<cipher name='dea' state='off'> --> dea-key-wrap=off
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
We have previously effectively ignored all <controller type='ide'>
elements in a domain definition.
On the i440fx-based machinetypes there is an IDE controller that is
included in the chipset and can't be removed (which is the ide
controller with index='0'>), so it makes sense to ignore that one
controller. However, if an i440fx domain definition has a 2nd
controller, nothing catches this error (unless you also have a disk
attached to it, in which case qemu will complain that you're trying to
use the ide controller named "ide1", which doesn't exist), and if any
other type of domain has even a single controller defined, it will be
incorrectly ignored.
Ignoring a bogus controller definition isn't such a big problem, as
long as an error is logged when any disk is attached to that
non-existent controller. But in the case of q35-based machinetypes,
the hardcoded id ("alias" in libvirt terms) of its builtin SATA
controller is "ide", which happens to be the same id as the builtin
IDE controller on i440fx machinetypes. So libvirt creates a
commandline believing that it is connecting the disk to the builtin
(but actually nonexistent) IDE controller, qemu thinks that libvirt
wanted that disk connected to the builtin SATA controller, and
everybody is happy.
Until you try to connect a 2nd disk to the IDE controller. Then qemu
will complain that you're trying to set unit=1 on a controller that
requires unit=0 (SATA controllers are organized differently than IDE
controllers).
After this patch, if a domain has an IDE controller defined for a
machinetype that has no IDE controllers, libvirt will log an error
about the controller itself as it is building the qemu commandline
(rather than a (possible) error from qemu about disks attached to that
controller). This is done by adding IDE to the list of controller
types that are handled in the loop that creates controller command
strings in qemuBuildCommandline() (previously it would *always* skip
IDE controllers). Then qemuBuildControllerDevStr() is modified to log
an appropriate error in the case of IDE controllers.
In the future, if we add support for extra IDE controllers (piix3-ide
and/or piix4-ide) we can just add it into the IDE case in
qemuBuildControllerDevStr(). For now, nobody seems anxious to add
extra support for an aging and very slow controller, when there are so
many better options available.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1176071 (Fedora)
This makes sure that that the commandlines generated for devices and
controller devices are all using the alias that has been set in the
controller's object as the id of the controller, rather than
hardcoding a printf (or worse, encoding exceptions to the standard
${controller}${index} into the logic)
Since this "fixes" the controller name used for the sata controller,
the commandline arg for the sata controller in the sata test case had
to be adjusted to be "sata0" instead of "ahci0". All other tests
remain unchanged, verifying that the patch causes no other functional
change.
Because the function that finds a controller alias based on a device
def requires a pointer to the full domainDef in order to get the list
of controllers, the arglist of a few functions had to have this added.
There are a few extra exceptions that weren't being accounted for when
creating the alias for a controller. This resulted in 1) incorrect
status XML, and 2) exceptions/printfs of what *should* have been
directly available in the controller alias when constructing device
commandline arguments:
1) The primary (and only) IDE controller on a 440FX machinetype is
hardcoded to be "ide" in qemu.
2) The primary SATA controller on a 440FX machinetype is also
hardcoded to be "ide" in qemu.
3) On machinetypes that don't support multiple PCI buses, the PCI bus
is hardcoded in qemu to have the name "pci".
4) The first usb master controller is "usb", all others are the normal
"usb%d". (note that usb controllers that are not a "master" will have
the same index, and thus alias, as the master).
We needed to pass in the full domainDef and qemuCaps in order to
properly make the decisions about these exceptions.
In the XML we have the vnc port number, but QEMU takes on command line
a vnc screen number, it's port-5900. We should fail with error message
that only ports in range [5900,65535] are valid.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1164966
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The code to add device type to the commandline was identical for lsi
and other models of SCSI controllers, but was duplicated (with the
exception of a minor ordering difference of the if-else clauses) for
the two cases. This patch replaces those two with a single instance of
the code just before the if().
This patch makes qemuValideDevicePCISlotsChipsets() more consistent in
appearance by replacing several clauses of an if with the equivalent
call to qemuDomainMachineIsI440FX. The if was checking exactly the
same items, just in a slightly different order.
Allow ccw devices to be used with multiqueues. ccw provides a one to
one relation of fds to queues and does not support the vectors option.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Coverity points out it was possible to have a zero return from
qemuBuildRNGBackendProps thus not filling in 'props' and then
causing a NULL dereference on the next call.
The only version that's supported in QEMU is version 2, currently.
Fortunately, it is enabled by aarch64 automatically, so there's
nothing for us that needs to be put onto command line.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Found by Laine and discussed a bit on internal IRC.
Commit id c56fe7f1d6 added support for creating a command line to support
scsi-disk.channel.
Series was here:
http://www.redhat.com/archives/libvir-list/2012-February/msg01052.html
Which pointed to a design proposal here:
http://permalink.gmane.org/gmane.comp.emulators.libvirt/50428
Which states (in part):
Libvirt should check for the QEMU "scsi-disk.channel" property. If it
is unavailable, QEMU will only support channel=lun=0 and 0<=target<=7.
However, the check added was ensuring that bus != lun *and* bus != 0. So
if bus == lun and both were non zero, we'd never make the second check.
Changing this to an *or* check fixes the check, but still is less readable
than the just checking each for 0
Rather than have a separate routine to parse the alias of an iothread
returned from qemu in order to get the iothread_id value, parse the alias
when returning and just return the iothread_id in qemuMonitorIOThreadInfoPtr
This set of patches removes the function, changes the "char *name" to
"unsigned int" and handles all the fallout.
Add 'thread_id' to the virDomainIOThreadIDDef as a means to store the
'thread_id' as returned from the live qemu monitor data.
Remove the iothreadpids list from _qemuDomainObjPrivate and replace with
the new iothreadids 'thread_id' element.
Rather than use the default numbering scheme of 1..number of iothreads
defined for the domain, use the iothreadid's list for the iothread_id
Since iothreadids list keeps track of the iothread_id's, these are
now used in place of the many places where a for loop would "know"
that the ID was "+ 1" from the array element.
The new tests ensure usage of the <iothreadid> values for an exact number
of iothreads and the usage of a smaller number of <iothreadid> values than
iothreads that exist (and usage of the default numbering scheme).
This revealed that GuestDefaultEmulator was a bit buggy, capable
of returning an emulator that didn't match the passed domain type. Fix
up the test suite input to continue to pass.
We support VNC for containers to have the same
interface with VMs. At this moment it just renders
linux text console.
Of course we don't pass any physical devices and
don't emulate virtual devices. Our VNC server
renders text from terminal master and sends
input events from VNC client to terminal.
So add special video type VIR_DOMAIN_VIDEO_TYPE_PARALLELS
for these pseudo-devices.
Signed-off-by: Dmitry Guryanov <dguryanov@parallels.com>
==19015== 968 (416 direct, 552 indirect) bytes in 1 blocks are definitely lost in loss record 999 of 1,049
==19015== at 0x4C2C070: calloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==19015== by 0x52ADF14: virAllocVar (viralloc.c:560)
==19015== by 0x5302FD1: virObjectNew (virobject.c:193)
==19015== by 0x1DD9401E: virQEMUDriverConfigNew (qemu_conf.c:164)
==19015== by 0x1DDDF65D: qemuStateInitialize (qemu_driver.c:666)
==19015== by 0x53E0823: virStateInitialize (libvirt.c:777)
==19015== by 0x11E067: daemonRunStateInit (libvirtd.c:905)
==19015== by 0x53201AD: virThreadHelper (virthread.c:206)
==19015== by 0xA1EE1F2: start_thread (in /lib64/libpthread-2.19.so)
==19015== by 0xA4EFC8C: clone (in /lib64/libc-2.19.so)
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Instead of always using controller 0 and incrementing port number,
respect the maximum port numbers of controllers and use all of them.
Ports for virtio consoles are quietly reserved, but not formatted
(neither in XML nor on QEMU command line).
Also rejects duplicate virtio-serial addresses.
https://bugzilla.redhat.com/show_bug.cgi?id=890606https://bugzilla.redhat.com/show_bug.cgi?id=1076708
Test changes:
* virtio-auto.args
Filling out the port when just the controller is specified.
switched from using
maxport + 1
to:
first free port on the controller
* virtio-autoassign.args
Filling out the address when no <address> is specified.
Started using all the controllers instead of 0, also discards
the bus value.
* xml -> xml output of virtio-auto
The port assignment is no longer done as a part of XML parsing,
so the unspecified values stay 0.
Starting a qemu VM with a memory module that has the base address
specified results in the following error:
error: internal error: early end of file from monitor: possible problem:
2015-03-26T03:45:52.338891Z qemu-kvm: -device pc-dimm,node=0,memdev=memdimm0,
id=dimm0,slot=0,base=4294967296: Property '.base' not found
The correct property name for the base address is 'addr'.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Because of the microcode update to Haswell/Broadwell CPUs, existing
domains using these CPUs may fail to start even though they used to run
just fine. To help users solve this issue we try to suggest switching to
-noTSX variant of the CPU model:
virsh # start cd
error: Failed to start domain cd
error: unsupported configuration: guest and host CPU are not
compatible: Host CPU does not provide required features: rtm, hle;
try using 'Haswell-noTSX' CPU model
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Use the virStorageSourceIsEmpty helper to determine whether the drive
source is empty rather than checking for src->path. This will fix start
of VM with empty network cdrom that would not report any error.
The function that formats the string for network drives would return
error code but did not set the error message when called on storage
source with VIR_STORAGE_NET_PROTOCOL_LAST or _NONE.
Report an error in this case if it would ever be called in that way.
When starting a VM with hotpluggable memory devices the user may specify
an invalid source NUMA node. Libvirt would pass through the error from
qemu:
# virsh start test3
error: Failed to start domain test3
error: internal error: process exited while connecting to monitor:
2015-03-25T01:12:17.205913Z qemu-kvm: -object memory-backend-ram,id=memdimm0
,size=536870912,host-nodes=1-3,policy=bind: cannot bind memory to host NUMA nodes:
Invalid argument
This patch adds a check that allows to report better error:
# virsh start test3
error: Failed to start domain test3
error: configuration unsupported: NUMA node 1 is unavailable
Signed-off-by: Luyao Huang <lhuang@redhat.com>
by rewriting it completely from:
error: unsupported configuration: virtio only support device address
type 'PCI'
to:
error: unsupported configuration: virtio disk cannot have an address of type
drive
Since we now support CCW addresses as well.
Add support to start qemu instance with 'pc-dimm' device. Thanks to the
refactors we are able to reuse the existing function to determine the
parameters.
To enable memory hotplug the maximum memory size and slot count need to
be specified. As qemu supports now other units than mebibytes when
specifying memory, use the new interface in this case.
In the last section if the function determines that the config is
invalid when QEMU doesn't support the memory device the JSON config
object would be returned even if it doesn't make sense.
Assign the object to be returned only on success.
Problem Description:
When we set boot order for a vhost-user network interface, we found the boot index
doesn't work.
Cause of the Problem:
In the function qemuBuildVhostuserCommandLine(), it forcely set the arg bootindex of
function qemuBuildNicDevStr() to 0. Thus, the bootindex parameter got missing.
Solution:
Trans the arg bootindex down.
Signed-off-by: Gao Haifeng <gaohaifeng.gao@huawei.com>
Signed-off-by: Zhang Bo <oscar.zhangbo@huawei.com>
The memory sizes in qemu are aligned up to 1 MiB boundaries. There are
two places where this was done once for the total size and then for
individual NUMA cell sizes.
Add a function that will align the sizes in one place so that it's clear
where the sizes are aligned.
As there are two possible approaches to define a domain's memory size -
one used with legacy, non-NUMA VMs configured in the <memory> element
and per-node based approach on NUMA machines - the user needs to make
sure that both are specified correctly in the NUMA case.
To avoid this burden on the user I'd like to replace the NUMA case with
automatic totaling of the memory size. To achieve this I need to replace
direct access to the virDomainMemtune's 'max_balloon' field with
two separate getters depending on the desired size.
The two sizes are needed as:
1) Startup memory size doesn't include memory modules in some
hypervisors.
2) After startup these count as the usable memory size.
Note that the comments for the functions are future aware and document
state that will be present after a few later patches.
We interpret port values as signed int (convert them from char *),
so if a negative value is provided in network disk's configuration,
we accept it as valid, however there's an 'unknown cause' error raised later.
This error is only accidental because we return the port value in the return code.
This patch adds just a minor tweak to the already existing check so we
reject negative values the same way as we reject non-numerical strings.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1163553
Error messages are already set in all code paths returning -1 from
networkGetNetworkAddress, so we don't want to overwrite them.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
Commit 4bbe1029f fixed a problem in commit f7afeddc by moving the call
to virNetDevGetIndex() to a location common to all interface types (so
that the nicindex array would be filled in for macvtap as well as tap
interfaces), but the location was *too* common, as the original call
to virNetDevGetIndex() had been in a section qualified by "if
(cfg->privileged)". The result was that the "fixed" libvirtd would try
to call virNetDevGetIndex() even for session mode libvirtd, and end up
failing with the log message:
Unable to open control socket: Operation not permitted
To remedy that, this patch qualifies the call to virNetDevGetIndex()
in its new location with cfg->privileged.
This resolves https://bugzilla.redhat.com/show_bug.cgi?id=1198244
There was a mess in the way how we store unlimited value for memory
limits and how we handled values provided by user. Internally there
were two possible ways how to store unlimited value: as 0 value or as
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED. Because we chose to store memory
limits as unsigned long long, we cannot use -1 to represent unlimited.
It's much easier for us to say that everything greater than
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED means unlimited and leave 0 as valid
value despite that it makes no sense to set limit to 0.
Remove unnecessary function virCompareLimitUlong. The update of test
is to prevent the 0 to be miss-used as unlimited in future.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1146539
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Pass the TPM file descriptor to QEMU via command line.
Instead of passing /dev/tpm0 we now pass /dev/fdset/10 and the additional
parameters -add-fd set=10,fd=20.
This addresses the use case when QEMU is started with non-root privileges
and QEMU cannot open /dev/tpm0 for example.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1142631
This patch resolves a situation where the same "<target dev='$name'...>"
can be used for multiple disks in the domain.
While the $name is "mostly" advisory regarding the expected order that
the disk is added to the domain and not guaranteed to map to the device
name in the guest OS, it still should be unique enough such that other
domblk* type operations can be performed.
Without the patch, the domblklist will list the same Target twice:
$ virsh domblklist $dom
Target Source
------------------------------------------------
sda /var/lib/libvirt/images/file.qcow2
sda /var/lib/libvirt/images/file.img
Additionally, getting domblkstat, domblkerror, domblkinfo, and other block*
type calls will not be able to reference the second target.
Fortunately, hotplug disallows adding a "third" sda value:
$ qemu-img create -f raw /var/lib/libvirt/images/file2.img 10M
$ virsh attach-disk $dom /var/lib/libvirt/images/file2.img sda
error: Failed to attach disk
error: operation failed: target sda already exists
$
BUT, it since 'sdb' doesn't exist one would get the following on the same
hotplug attempt, but changing to use 'sdb' instead of 'sda'
$ virsh attach-disk $dom /var/lib/libvirt/images/file2.img sdb
error: Failed to attach disk
error: internal error: unable to execute QEMU command 'device_add': Duplicate ID 'scsi0-0-1' for device
$
Since we cannot fix this issue at parsing time, the best that can be done so
as to not "lose" a domain is to make the check prior to starting the guest
with the results as follows:
$ virsh start $dom
error: Failed to start domain $dom
error: XML error: target 'sda' duplicated for disk sources '/var/lib/libvirt/images/file.qcow2' and '/var/lib/libvirt/images/file.img'
$
Running 'make check' found a few more instances in the tests where this
duplicated target dev value was being used. These also exhibited some
duplicated 'id=' values (negating the uniqueness argument of aliases) in
the corresponding .args file and of course the *xmlout version of a few
input XML files.
If we combine the boot order on the command line with other
boot options, we prepend order= in front of it.
Instead of checking if the number of added arguments is between
0 and 2, separate the strings for boot order and options
and prepend boot order only if both strings are not empty.
Commit f7afeddc added code to report to systemd an array of interface
indexes for all tap devices used by a guest. Unfortunately it not only
didn't add code to report the ifindexes for macvtap interfaces
(interface type='direct') or the tap devices used by type='ethernet',
it ended up sending "-1" as the ifindex for each macvtap or hostdev
interface. This resulted in a failure to start any domain that had a
macvtap or hostdev interface (or actually any type other than
"network" or "bridge").
This patch does the following with the nicindexes array:
1) Modify qemuBuildInterfaceCommandLine() to only fill in the
nicindexes array if given a non-NULL pointer to an array (and modifies
the test jig calls to the function to send NULL). This is because
there are tests in the test suite that have type='ethernet' and still
have an ifname specified, but that device of course doesn't actually
exist on the test system, so attempts to call virNetDevGetIndex() will
fail.
2) Even then, only add an entry to the nicindexes array for
appropriate types, and to do so for all appropriate types ("network",
"bridge", and "direct"), but only if the ifname is known (since that
is required to call virNetDevGetIndex().
If the qemu binary on x86 does not support lsi SCSI controller,
but it supports virtio-scsi, we reject the virtio-specific attributes
for no reason.
Move the default controller assignment before the check.
https://bugzilla.redhat.com/show_bug.cgi?id=1168849
Since s390 does not support usb the default creation of a usb controller
for a domain should not occur.
Also adjust s390 test cases by removing usb device instances since
usb devices are no longer created by default for s390 the s390
test cases need to be adjusted.
Signed-off-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
For historical reasons data regarding NUMA configuration were split
between the CPU definition and numatune. We cannot do anything about the
XML still being split, but we certainly can at least store the relevant
data in one place.
This patch moves the NUMA stuff to the right place.
Name it virNumaMemAccess and add it to conf/numa_conf.[ch]
Note that to avoid a circular dependency the type of the NUMA cell
memAccess variable was changed to int. It will be turned back later
after the circular dependency will not exist.
PowerPC : Forbid NULL CPU model with 'host-model' mode in qemu command line.
This ensures that an XML such as following:
...
<cpu mode='host-model'>
<model fallback='allow'/>
</cpu>
...
will not generate a '-cpu host,compat=(null)' command line with qemu-system-ppc64.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
So, when building the '-numa' command line, the
qemuBuildMemoryBackendStr() function does quite a lot of checks to
chose the best backend, or to check if one is in fact needed. However,
it returned that backend is needed even for this little fella:
<numatune>
<memory mode="strict" nodeset="0,2"/>
</numatune>
This can be guaranteed via CGroups entirely, there's no need to use
memory-backend-ram to let qemu know where to get memory from. Well, as
long as there's no <memnode/> element, which explicitly requires the
backend. Long story short, we wouldn't have to care, as qemu works
either way. However, the problem is migration (as always). Previously,
libvirt would have started qemu with:
-numa node,memory=X
in this case and restricted memory placement in CGroups. Today, libvirt
creates more complicated command line:
-object memory-backend-ram,id=ram-node0,size=X
-numa node,memdev=ram-node0
Again, one wouldn't find anything wrong with these two approaches.
Both work just fine. Unless you try to migrated from the older libvirt
into the newer one. These two approaches are, unfortunately, not
compatible. My suggestion is, in order to allow users to migrate, lets
use the older approach for as long as the newer one is not needed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Export the required helpers and add backend code to hotplug RNG devices.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
As the RNG device is using an -object as backend refactor the code to
use the JSON to commandline generator so that we can reuse the code
later in hotplug.
Move the alias name right after the object type for rng-egd backend so
that we can later use the JSON to commandline generator to create the
command line.
Libvirt didn't prefix the random number generator backend object alias
with any string thus the device alias and object alias were identical.
To avoid possible problems, rename the alias for the backend object and
tweak tests to comply with the change.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Rename qemuBuildRNGDeviceArgs to qemuBuildRNGDevStr and change the
return type so that it can be reused in the device hotplug code later.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
This function is used to assign an alias for a RNG device. It will be
later reused when hotplugging RNGs.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
It is only usable for NETWORK and BRIDGE type interfaces.
Error out when trying to start a domain where the custom
tap device path is specified for interfaces of other types,
or when the daemon is not privileged.
Note that this cannot be checked at definition time, because
the comparison is against actual type.
https://bugzilla.redhat.com/show_bug.cgi?id=1147195
Some code paths have special logic depending on the page size
reported by sysconf, which in turn affects the test results.
We must mock this so tests always have a consistent page size.
Change done by commit f309db1f4d wrongly
assumes that qemu can start with a combination of NUMA nodes specified
with the "memdev" option and the appropriate backends, and the legacy
way by specifying only "mem" as a size argument. QEMU rejects such
commandline though:
$ /usr/bin/qemu-system-x86_64 -S -M pc -m 1024 -smp 2 \
-numa node,nodeid=0,cpus=0,mem=256 \
-object memory-backend-ram,id=ram-node1,size=12345 \
-numa node,nodeid=1,cpus=1,memdev=ram-node1
qemu-system-x86_64: -numa node,nodeid=1,cpus=1,memdev=ram-node1: qemu: memdev option must be specified for either all or no nodes
To fix this issue we need to check if any of the nodes requires the new
definition with the backend and if so, then all other nodes have to use
it too.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182467
With the new JSON to argv formatter we are now able to represent the
memory backend definitions in the JSON object format that is reusable
for monitor use (hotplug) and then convert it into the shell string.
This will avoid having two separate instances of the same code that
would create the different formats.
Previous refactors now allow to make this step without changes to the
test suite.
QEMU's command line visitor as well as the JSON interface take bytes by
default for memory object sizes. Convert mebibytes to bytes so that we
can later refactor the existing code for hotplug purposes.
QEMU's qapi visitor code allows yes/on/y for true and no/off/n for false
value of boolean properities. Unify the used style so that we can
generate it later and fix test cases.
Extract the memory backend device code into a separate function so that
it can be later easily refactored and reused.
Few small changes for future reusability, namely:
- new (currently unused) parameter for user specified page size
- size of the memory is specified in kibibytes, divided up in the
function
- new (currently unused) parameter for user specifed source nodeset
- option to enforce capability check
Unlike -device, qemu uses a JSON object to add backend "objects" via the
monitor rather than the string that would be passed on the commandline.
To be able to reuse code parts that configure backends for various
devices, this patch adds a helper that will allow generating the command
line representations from the JSON property object.
For distros that want to add versioned machine types, they will add
(downstream) machine types like "virt-foo-1.2.3". Detect these as
MMIO too.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Previous patch of this series fixed the issue with adding a new PCI bridge
when all the slots were reserved by devices with user specified addresses.
In case there are still some PCI devices waiting to get a slot reserved
by qemuAssignDevicePCISlots, this means a new bus needs to be
created along with a corresponding bridge controller. By adding an
additional check, this scenario now results in a reasonable error
instead of generating wrong qemu command line.
Commit 93c8ca tried to fix the issue with auto-adding of a PCI bridge
controller, but didn't work properly in all scenarios.
This patch provides a better fix of the issue when all slots on a PCI bus
are reserved by devices with user specified addresses and no additional
bridges need to be created.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1132900
In order to be able to test for fully reserved PCI buses, assignment of
PCI slots for integrated devices needs to be moved to a separate function.
This also might be a good preparation if we decide to add support for
other chipsets as well.
Move qemuDomainAssignPCIAddresses after the definition
of the static function qemuDomainValidateDevicePCISlotsQ35.
This lets us define a new static function using
qemuDomainValidateDevicePCISlots* and use it in
qemuDomainAssignPCIAddresses without a forward declaration.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
As it turned out, fix of dead code 419a22 changed the affected condition
from "never true" to "always true", so better fix would be to change the
return code of virDomainMaybeAddController from 0 to 1 if
a new bridge has been added, thus distinguishing case when we didn't need to
add any controller and case we successfully added one.
The return code is changed in the next commit
https://bugzilla.redhat.com/show_bug.cgi?id=1164627
When using 'virsh attach-device' to hotplug an unsupported console type
into a qemu guest the attachment would succeed as the command line
formatter didn't report error in such case.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1130390
The listen address is not mandatory for <interface type='server'>
but when it's not specified, we've been formatting it as:
-netdev socket,listen=(null):5558,id=hostnet0
which failed with:
Device 'socket' could not be initialized
Omit the address completely and only format the port in the listen
attribute.
Also fix the schema to allow specifying a model.
Ploop is a pseudo device which makeit possible to access
to an image in a file as a block device. Like loop devices,
but with additional features, like snapshots, write tracker
and without double-caching.
It used in PCS for containers and in OpenVZ. You can manage
ploop devices and images with ploop utility
(http://git.openvz.org/?p=ploop).
Signed-off-by: Dmitry Guryanov <dguryanov@parallels.com>
We tested for positive return value from virDomainMaybeAddController,
but it returns 0 or -1 only resulting in a dead code.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In case we find out, there are more PCI devices to be connected
than there are available slots on the default PCI bus, we automatically add a
new bus and a related PCI bridge controller as well. As there are no free slots
left on the default PCI bus, PCI bridge controller gets a free slot on a
newly created PCI bus which causes qemu to refuse to start the guest.
This fix introduces a new function qemuDomainPCIBusFullyReserved which
is checked right before we possibly try to reserve a slot for PCI bridge
controller.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1132900
https://bugzilla.redhat.com/show_bug.cgi?id=1165993
So, there are still plenty of vNIC types that we don't know how to set
bandwidth on. Let's warn explicitly in case user has requested it
instead of pretending everything was set.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
QEMU supports feature specification with -cpu host and we just skip
using that. Since QEMU developers themselves would like to use this
feature, this patch modifies the code to work.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178850
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The default value should be 16 MiB instead of 8 MiB. Only really old
version of upstream QEMU used the 8 MiB as default for vga framebuffer.
Without this change if you update your libvirt where we introduced the
"vgamem" attribute for QXL video device the value will be set to 8 MiB,
but previously your guest had 16 MiB because we didn't pass any value to
QEMU command line which means QEMU used its own 16 MiB as default.
This will affect all users with guest's display resolution higher than
1920x1080.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
In one of my previous commits (311b4a67) I've tried to allow to
pass regular system pages to <hugepages>. However, there was a
little bug that wasn't caught. If domain has guest NUMA topology
defined, qemuBuildNumaArgStr() function takes care of generating
corresponding command line. The hugepages backing for guest NUMA
nodes is handled there too. And here comes the bug: the hugepages
setting from XML is stored in KiB internally, however, the system
pages size was queried and stored in Bytes. So the check whether
these two are equal was failing even if it shouldn't.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Libvirt BZ: https://bugzilla.redhat.com/show_bug.cgi?id=1175397
QEMU BZ: https://bugzilla.redhat.com/show_bug.cgi?id=1170093
In qemu there are two interesting arguments:
1) -numa to create a guest NUMA node
2) -object memory-backend-{ram,file} to tell qemu which memory
region on which host's NUMA node it should allocate the guest
memory from.
Combining these two together we can instruct qemu to create a
guest NUMA node that is tied to a host NUMA node. And it works
just fine. However, depending on machine type used, there might
be some issued during migration when OVMF is enabled (see QEMU
BZ). While this truly is a QEMU bug, we can help avoiding it. The
problem lies within the memory backend objects somewhere. Having
said that, fix on our side consists on putting those objects on
the command line if and only if needed. For instance, while
previously we would construct this (in all ways correct) command
line:
-object memory-backend-ram,size=256M,id=ram-node0 \
-numa node,nodeid=0,cpus=0,memdev=ram-node0
now we create just:
-numa node,nodeid=0,cpus=0,mem=256
because the backend object is obviously not tied to any specific
host NUMA node.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When libvirt is managing a bridge's forwarding database (FDB)
(macTableManager='libvirt'), if we add FDB entries for a new guest
interface even before the qemu process is created, then in the case of
a migration any other guest attached to the "destination" bridge will
have its traffic immediately sent to the destination of the migration
even while the source domain is still running (and the destination, of
course, isn't). To make sure that traffic from other guests on the new
host continues flowing to the old guest until the new one is ready, we
have to wait until the new guest CPUs are started to add the FDB
entries.
Conversely, we need to remove the FDB entries from the bridge any time
the guest CPUs are stopped; among other things, this will assure
proper operation during a post-copy migration (which is just the
opposite of the problem described in the previous paragraph).
https://bugzilla.redhat.com/show_bug.cgi?id=1173507
It occurred to me that OpenStack uses the following XML when not using
regular huge pages:
<memoryBacking>
<hugepages>
<page size='4' unit='KiB'/>
</hugepages>
</memoryBacking>
However, since we are expecting to see huge pages only, we fail to
startup the domain with following error:
libvirtError: internal error: Unable to find any usable hugetlbfs
mount for 4 KiB
While regular system pages are not huge pages technically, our code is
prepared for that and if it helps OpenStack (or other management
applications) we should cope with that.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
qemuNetworkIfaceConnect() used to have a special case for
actualType='network' (a network with forward mode of route, nat, or
isolated) to call the libvirt public API to retrieve the bridge being
used by a network. That is no longer necessary - since all network
types that use a bridge and tap device now get the bridge name stored
in the ActualNetDef, we can just always use
virDomainNetGetActualBridgeName() instead.
(an audit of the two callers to qemuNetworkIfaceConnect() confirms
that it is never called for any other type of network, so the dead
code in the else statement (logging an internal error if it is called
for any other type of network) is eliminated in the process.)
When libvirt is managing the MAC table of a Linux host bridge, it must
turn off learning and unicast_flood for each tap device attached to
that bridge, then add a Forwarding Database (fdb) entry for the tap
device using the MAC address from the domain interface config.
Once we have disabled learning and flooding, any packet that has a
destination MAC address not present in the fdb will be dropped by the
bridge. This, along with the opportunistic disabling of promiscuous
mode[*], can result in enhanced network performance. and a potential
slight security improvement.
[*] If there is only one device on the bridge with learning/unicast_flood
enabled, then that device will automatically have promiscuous mode
disabled. If there are *no* devices with learning/unicast_flood
enabled (e.g. for a libvirt "route", "nat", or isolated network that
has no physical device attached), then all non-tap devices will have
promiscuous mode disabled (tap devices always have promiscuous mode
enabled, which may be a bug in the kernel, but in practice has 0
effect).
None of this has any effect for kernels prior to 3.15 (upstream kernel
commit 2796d0c648c940b4796f84384fbcfb0a2399db84 "bridge: Automatically
manage port promiscuous mode"). Even after that, until kernel 3.17
(upstream commit 5be5a2df40f005ea7fb7e280e87bbbcfcf1c2fc0 "bridge: Add
filtering support for default_pvid") traffic will not be properly
forwarded without manually adding vlan table entries. Unfortunately,
although the presence of the first patch is signalled by existence of
the "learning" and "unicast_flood" options in sysfs, there is no
reliable way to query whether or not the system's kernel has the
second of those patches installed, the only thing that can be done is
to try the setting and see if traffic continues to pass.
Since virNetworkFree will call virObjectUnref anyway, let's just use that
directly so as to avoid the possibility that we inadvertently clear out
a pending error message when using the public API.
Add attribute to set vgamem_mb parameter of QXL device for QEMU. This
value sets the size of VGA framebuffer for QXL device. Default value in
QEMU is 8MB so reuse it also in libvirt to not break things.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
So far we didn't have any option to set video memory size for qemu video
devices. There was only the vram (ram for QXL) attribute but it was valid
only for the QXL video device.
To provide this feature to users QEMU has a dedicated device attribute
called 'vgamem_mb' to set the video memory size. We will use the 'vram'
attribute for setting video memory size for other QEMU video devices.
For the cirrus device we will ignore the vram value because it has
hardcoded video size in QEMU.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
QEMU has two different type of QXL display device. The first "qxl-vga"
is for primary video device and second "qxl" is for secondary video
device.
There are also two different ways how to specify those devices on qemu
command line, the first one and obsolete is using "-vga" option and the
current new one is using "-device" option. The "-vga" could be used only
to setup primary video device, so the "-vga qxl" equal to
"-device qxl-vga". Unfortunately the "-vga qxl" doesn't support setting
additional parameters for the device and "-global" option must be used
for this purpose. It's mandatory to use "-global qxl-vga...." to set the
parameters of primary video device previously defined with "-vga qxl".
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The vram attribute was introduced to set the video memory but it is
usable only for few hypervisors excluding QEMU/KVM and the old XEN
driver. Only in case of QEMU the vram was used for QXL.
This patch updates the documentation to reflect current code in libvirt
and also changes the cases when we will set the default vram attribute.
It also fixes existing strange default value for VGA devices 9MB to 16MB
because the video ram should be rounded to power of two.
The change of default value could affect migrations but I found out that
QEMU always round the video ram to power of two internally so it's safe
to change the default value to the next closest power of two and also
silently correct every domain XML definition. And it's also safe because
we don't pass the value to QEMU.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
To be able to express some use cases of the RBD backing with libvirt, we
need to be able to specify a config file for the RBD client to qemu as
that is one of the commonly used options.
Some storage systems have internal support for snapshots. Libvirt should
be able to select a correct snapshot when starting a VM.
This patch adds a XML element to select a storage source snapshot for
the RBD protocol which supports this feature.
To allow reuse this non-trivial parser code in the backing store parser
this part of the command line parser needs to be split out into a
separate funciton.
Instead of splitting out various fields, pass the complete structure and
let the function pick various things of it.
As one of the callers isn't using virStorageSourcePtr to store the data,
this patch adds glue code that fills the data into a dummy
virStorageSourcePtr before calling the func.
This change will help when adding new fields that need output processing
in the future.
As discussed on the upstream list, it's better not to make this
kind of predictions in libvirt. It may happen that qemu learns
how to enable OVMF on other architectures too and we shouldn't
try to chase that.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Currently, we are whitelisting architectures, that we know how to run
OVMF on. So far, only x86_64 was enabled. However, looking at qemu
code, the same commandline can be used to enable OVMF for armv7l and
aarch64.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Ethernet interfaces in libvirt currently do not support bandwidth setting.
For example, following xml file for an interface will not apply these
settings to corresponding qdiscs.
<interface type="ethernet">
<mac address="02:36:1d:18:2a:e4"/>
<model type="virtio"/>
<script path=""/>
<target dev="tap361d182a-e4"/>
<bandwidth>
<inbound average="984" peak="1024" burst="64"/>
<outbound average="2000" peak="2048" burst="128"/>
</bandwidth>
</interface>
Signed-off-by: Anirban Chakraborty <abchak@juniper.net>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Seems the 'size_iops_sec' was a late add and the checks for whether
the field was defined, but unsupported and the maximum size of the
field were not being made.
Also, adjust blkdeviotune support error message for grammar, spelling
(paramater), and remove the "(need QEMU 1.7 or superior)". None of
our other similar error messages list which QEMU version is required.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Check the arability of the options with the current qemu binary,
add them in the varable opt if yes, print a message if not.
Signed-off-by: Matthias Gatto <matthias.gatto@outscale.com>
PowerISA allows processors to run VMs in binary compatibility ("compat")
mode supporting an older version of ISA. QEMU has recently added support to
explicitly denote a VM running in compatibility mode through commit 6d9412ea
& 8dfa3a5e85. Now, a "compat" mode VM can be run by invoking this qemu
commandline on a POWER8 host: -cpu host,compat=power7.
This patch allows libvirt to exploit cpu mode 'host-model' to describe this
new mode for PowerKVM guests. For example, when a user wants to request a
power7 vm to run in compatibility mode on a Power8 host, this can be
described in XML as follows :
<cpu mode='host-model'>
<model>power7</model>
</cpu>
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Li Zhang <zhlcindy@linux.vnet.ibm.com>
Signed-off-by: Pradipta Kr. Banerjee <bpradip@in.ibm.com>
Acked-by: Michal Privoznik <mprivozn@redhat.com>
This adds support for PowerPC Little Endian architecture.,
and allows libvirt to spawn VMs based on 'ppc64le' architecture.
Signed-off-by: Pradipta Kr. Banerjee <bpradip@in.ibm.com>
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Extending the iothread disk support from pci to pci and ccw.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Finding the right type of disk should check for virtio as bus and
pci as device address type.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
This is a reaction to Michal's fix [1] for non-NUMA systems that also
splits out conf/ out of util/ because libvirt_util shouldn't require
libvirt_conf if it is the other way around. This particular use case
worked, but we're trying to avoid it as mentioned [2], many times.
The only functions from virnuma.c that needed numatune_conf were
virDomainNumatuneNodesetIsAvailable() and virNumaSetupMemoryPolicy().
The first one should be in numatune_conf as it works with
virDomainNumatune, the second one just needs nodeset and mode, both of
which can be passed without the need of numatune_conf.
Apart from fixing that, this patch also fixes recently added
code (between commits d2460f85^..5c8515620) that doesn't support
non-contiguous nodesets. It uses new function
virNumaNodesetIsAvailable(), which doesn't need a stub as it doesn't use
any libnuma functions, to check if every specified nodeset is available.
[1] https://www.redhat.com/archives/libvir-list/2014-November/msg00118.html
[2] http://www.redhat.com/archives/libvir-list/2011-June/msg01040.html
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Since there was a valid note to patch 43b67f2e about the best spot to
check for bandwidth set call while having libvirt daemon run in session
mode, this patch reverts previous changes dealing with bandwith
(also reverts adding variable @cfg in qemuDomainGetNumaParameters which
does not have any use at the moment, but getting and unreferencing
driver's config) in qemu_driver.c and qemu_command.c. There will be
another patch in the series which introduces the fix itself.
Domain memory elements such as max_balloon and cur_balloon are
implemented as 'unsigned long long', whereas the 'memory' element
in NUMA cells is implemented as 'unsigned int'.
Use the same data type (unsigned long long) for 'memory' element
in NUMA cells.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
There was no check for 'nodeset' attribute in numatune-related
elements. This patch adds validation that any nodeset specified does
not exceed maximum host node.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Particularly in qemuBuildNumaArgStr(), there was a need for the advice
due to memory backing, which needs to know the nodeset it will be pinned
to. With newer qemu this caused the following error when starting
domain:
error: internal error: Advice from numad is needed in case of
automatic numa placement
even when starting perfectly valid domain, e.g.:
...
<vcpu placement='auto'>4</vcpu>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
<cpu>
<numa>
<cell id='0' cpus='0' memory='524288'/>
<cell id='1' cpus='1' memory='524288'/>
</numa>
</cpu>
...
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1138545
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Tuning NUMA or network interface parameters requires root
privileges to manage cgroups. Thus an attempt to set some of these
parameters in session mode on a running domain should be invalid
followed by an error. An example might be memory tuning which raises
an error in such case.
The following behavior in session mode will be present after applying
this patch:
Tuning | SET | GET |
----------|---------------|--------|
NUMA | shut off only | always |
Memory | never | never |
Interface | never | always |
Resolves https://bugzilla.redhat.com/show_bug.cgi?id=1126762
This patch implements support for the ivshmem device in QEMU.
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Right now when building the qemu command line, we try to do various
unconditional validations of the guest CPU against the host CPU. However
this checks are overly applied. The only time we should use the checks
are:
- The user requests host-model/host-passthrough, or
- When KVM is requsted. CPU features requested in TCG mode are always
emulated by qemu and are independent of the host CPU, so no host CPU
checks should be performed.
Right now if trying to specify a CPU for arm on an x86 host, it attempts
to do non-sensical validation and falls over.
Switch all the test cases that were intending to test CPU validation to
use KVM, so they continue to test the intended code.
Amend some aarch64 XML tests with a CPU model, to ensure things work
correctly.
In the function at one place we check if def->cpu is NULL prior
to accessing def->cpu->ncells. Then, later in the code,
def->cpu->ncells is accessed directly, without the check. This
makes coverity unhappy, because the first check makes it think
def->cpu can be NULL. However, the function is not called if
def->cpu is NULL. Therefore, remove the first check and hopefully
make coverity cheer again.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This patch adds support for RDMA protocol in migration URIs.
USAGE: $ virsh migrate --live --migrateuri rdma://hostname domain qemu+ssh://hostname/system
Since libvirt runs QEMU in a pretty restricted environment, several
files needs to be added to cgroup_device_acl (in qemu.conf) for QEMU to
be able to access the host's infiniband hardware. Full documenation of
the feature can be found on QEMU wiki:
http://wiki.qemu.org/Features/RDMALiveMigration
Signed-off-by: Michael R. Hines <mrhines@us.ibm.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
commit 72f919f558 introduced an user
friendly error message when trying to use IDE disks as readonly.
Do the same thing for the SATA bus.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1112939
Signed-off-by: Giuseppe Scrivano <gscrivan@redhat.com>
We are not detecting the presence of FIPS from QEMU, but from procfs and
that means it's not QEMU capability. It was decided that we will pass
this flag to QEMU even if it's not supported by old QEMU binaries.
This patch also reverts changes done by commit a21cfb0f to
qemucapabilitestest and implements a new test case in qemuxml2argvtest.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1135431
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Currently, build with clang fails with:
CC qemu/libvirt_driver_qemu_impl_la-qemu_command.lo
qemu/qemu_command.c:6580:58: error: implicit conversion from enumeration type
'virMemAccess' to different enumeration type 'virTristateSwitch'
[-Werror,-Wenum-conversion]
virTristateSwitch memAccess = def->cpu->cells[i].memAccess;
~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~^~~~~~~~~
1 error generated.
Fix that by using virMemAccess instead of virTristateSwitch.
https://bugzilla.redhat.com/show_bug.cgi?id=1135396
There are two ways how to tell qemu to use huge pages. The first one
is suitable for domains with NUMA nodes: the path to hugetlbfs mount
is appended to NUMA node definition on the command line. The second
one is suitable for UMA domains: here there's this global '-mem-path'
argument that accepts path to the hugetlbfs mount point. However, the
latter case was not used for all the cases that it should be. For
instance:
<memoryBacking>
<hugepages>
<page size='2048' unit='KiB' nodeset='0'/>
</hugepages>
</memoryBacking>
didn't trigger the '-mem-path' so the huge pages - despite being
configured - were not used at all.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of 136ad4974 it is possible to specify different huge pages per
guest NUMA node. However, there's no check if nodeset specified in
./hugepages/page contains only those guest NUMA nodes that exist.
In other words with current code it is possible to define meaningless
combination:
<memoryBacking>
<hugepages>
<page size='1048576' unit='KiB' nodeset='0,2-3'/>
<page size='2048' unit='KiB' nodeset='1,4'/>
</hugepages>
</memoryBacking>
<vcpu placement='static'>4</vcpu>
<cpu>
<numa>
<cell id='0' cpus='0' memory='1048576'/>
<cell id='1' cpus='1' memory='1048576'/>
<cell id='2' cpus='2' memory='1048576'/>
<cell id='3' cpus='3' memory='1048576'/>
</numa>
</cpu>
Notice the node 4 in <hugepages/>?
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
qemu for IBM Power processor architecture is adding functionality for
supporting multiple 'pseries' machine type versions, each with different
capabilities. This patch is for supporting the same
Signed-off-by: Pradipta Kr. Banerjee <bpradip@in.ibm.com>
QEMU now supports UEFI with the following command line:
-drive file=/usr/share/OVMF/OVMF_CODE.fd,if=pflash,format=raw,unit=0,readonly=on \
-drive file=/usr/share/OVMF/OVMF_VARS.fd,if=pflash,format=raw,unit=1 \
where the first line reflects <loader> and the second one <nvram>.
Moreover, these two lines obsolete the -bios argument.
Note that UEFI is unusable without ACPI. This is handled properly now.
Among with this extension, the variable file is expected to be
writable and hence we need security drivers to label it.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Up to now, users can configure BIOS via the <loader/> element. With
the upcoming implementation of UEFI this is not enough as BIOS and
UEFI are conceptually different. For instance, while BIOS is ROM, UEFI
is programmable flash (although all writes to code section are
denied). Therefore we need new attribute @type which will
differentiate the two. Then, new attribute @readonly is introduced to
reflect the fact that some images are RO.
Moreover, the OVMF (which is going to be used mostly), works in two
modes:
1) Code and UEFI variable store is mixed in one file.
2) Code and UEFI variable store is separated in two files
The latter has advantage of updating the UEFI code without losing the
configuration. However, in order to represent the latter case we need
yet another XML element: <nvram/>. Currently, it has no additional
attributes, it's just a bare element containing path to the variable
store file.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
qemu now checks for invalid address type for a panic device, which is
currently implemented only to use ISA address type, thus rejecting
any other options, except for leaving XML attributes blank, in that case,
defaults are used (this behaviour remains the same from earlier verions).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1138125
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Currently, there is one flag passed in during macvtap creation
(withTap) -- Let's convert this field to an unsigned int flag
field for future expansion.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
For virtio-blk-pci disks with the disk iothread attribute that are
running the correct emulator, add the "iothread=iothread#" to the
-device command line in order to enable iothreads for the disk as
long as the command is available, the disk iothread value provided is
valid, and is supported for the disk device being added
Add a new capability to ensure the iothreads feature exists for the qemu
emulator being run - requires the "query-iothreads" QMP command. Using the
domain XML add correspoding command argument in order to generate the
threads. The iothreads will use a name space "iothread#" where, the
future patch to add support for using an iothread to a disk definition to
merely define which of the available threads to use.
Add tests to ensure the xml/argv processing is correct. Note that no
change was made to qemuargv2xmltest.c as processing the -object element
would require knowing more than just iothreads.
One useless warning, but the other one rather pertinent. On entry
the 'trans' variable is initialized to VIR_DOMAIN_DISK_TRANS_DEFAULT.
When the "trans" was found in the parsing loop it def->geometry.trans
was assigned to the return from virDomainDiskGeometryTransTypeFromString
and then 'trans' was used to do the comparison to see if it was valid.
So remove 'trans' and use def->geometry.trans properly
In qemuNetworkIfaceConnect() a call to virNetDevBandwidthSet() is
made where the function prototype requires the first parameter
(net->ifname) to be non NULL. Coverity complains that the subsequent
non NULL check for net->ifname prior to the next call gets flagged as
an unnecessary check. Resolve by removing the extra check
According to docs/schemas/domaincommon.rng and _virDomainBlockIoTuneInfo
all the iotune values are interpreted as unsigned long long, however
according to qemu_monitor_json.c, qemu silently truncates numbers
larger than LLONG_MAX. There's really not much of a usage for such
large numbers anyway yet. This patch provides the same overflow
check during a domain start as it does during setting
a blkdeviotune element in qemu_driver.c and thus reports an error when
a larger number than LLONG_MAX is detected.
https://bugzilla.redhat.com/show_bug.cgi?id=1131876
QEMU 2.1 added support for the kvm=off option to the -cpu command,
allowing the KVM hypervisor signature to be hidden from the guest.
This enables disabling of some paravirualization features in the
guest as well as allowing certain drivers which test for the
hypervisor to load. Domain XML syntax is as follows:
<domain type='kvm>
...
<features>
...
<kvm>
<hidden state='on'/>
</kvm>
</features>
...
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1078126
Using 'virsh attach-device --config' (or --persistent) to attach a
file backed lun device will succeed; however, subsequent domain restarts
will result in failure because the configuration of a file backed lun
is not supported.
Although allowing 'illegal configurations' is something that can be
allowed, it may not be practical in this case. Generally, when attaching
a device to a domain means the domain must be running. A way around
this is using the --config (or --persistent) option. When an attach
is done to a running domain, a temporary configuration is modified
first followed by the live update. The live update will make a number
of disk validity checks when building the qemu command to attach the
disk. If any fail, then change is rejected.
Rather than allow a potentially illegal combination, adjust the code
in the configuration path to make the same checks as the running path
will make with respect to disk validity checks. This way we avoid
having the potential for some subsequent start/reboot to fail because
an illegal combination was allowed.
NB: The live path still checks the configuration since it is possible
to just do --live guest modification...
https://bugzilla.redhat.com/show_bug.cgi?id=1095636
When starting up the domain the domain's NICs are allocated. As of
1f24f682 (v1.0.6) we are able to use multiqueue feature on virtio
NICs. It breaks network processing into multiple queues which can be
processed in parallel by different host CPUs. The queues are, however,
created by opening /dev/net/tun several times. Unfortunately, only the
first FD in the row is labelled so when turning the multiqueue feature
on in the guest, qemu will get AVC denial. Make sure we label all the
FDs needed.
Moreover, the default label of /dev/net/tun doesn't allow
attaching a queue:
type=AVC msg=audit(1399622478.790:893): avc: denied { attach_queue }
for pid=7585 comm="qemu-kvm"
scontext=system_u:system_r:svirt_t:s0:c638,c877
tcontext=system_u:system_r:virtd_t:s0-s0:c0.c1023
tclass=tun_socket
And as suggested by SELinux maintainers, the tun FD should be labeled
as svirt_t. Therefore, we don't need to adjust any range (as done
previously by Guannan in ae368ebf) rather set the seclabel of the
domain directly.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
